P2160 October 2003 rev E High Frequency LCD Panel EMI Reduction IC Features FCC approved method of EMI attenuation Provides up to 20 dB of EMI suppression Generates a low EMI spread spectrum clock of the input frequency 40 MHz to 166 MHz input frequency range Optimized for SVGA, XGA and high resolution SXGA and UXGA LCD panels Internal loop filter minimizes external components and board space 2 selectable spreading options SSON# control pin for spread spectrum enable and disable options 2 selectable modulation rates Low cycle-to-cycle jitter 3.3V operating range 16 mA output drives 16 mA output drives TTL or CMOS compatible outputs Low power CMOS design Supports most mobile graphic accelerator specifications Available in 8 pin SOIC and TSSOP typical narrow band signal produced by oscillators and most frequency generators. Lowering EMI by increasing a signal's bandwidth is called "spread spectrum clock generation" reducing the number of circuit board layers and shielding that are traditionally required to pass EMI regulations. The P2160 uses the most efficient and optimized modulation profile approved by the FCC and is implemented in a proprietary all-digital method. The P2160 modulates the output of a single PLL in order to "spread" the bandwidth of a synthesized clock and, more importantly, decreases the peak amplitudes of its harmonics. This results in significantly lower system EMI compared to the typical narrow band signal produced by oscillators and most frequency generators. Lowering EMI by increasing a signal's bandwidth is called "spread spectrum clock generation". Applications The P2160 is targeted towards digital flat panel applications for Notebook PCs, Palm-size PCs, Office Automation Equipments, and LCD Monitors, Digital Still Cameras and GPS Devices. Product Description The P2160 is a selectable spread spectrum frequency modulator designed compared to the Block Diagram Alliance Semiconductor 2575, Augustine Drive * Santa Clara, CA * Tel: 408.855.4900 * Fax: 408.855.4999 * www.alsc.com Notice: The information in this document is subject to change without notice. P2160 October 2003 rev E Pin Configuration Pin Description Pin# Pin Name Type 1 CLKIN I 2 FSO I 3 MRA I 4 VSS P 5 SSON# I 6 ModOUT O 7 SRO I 8 VDD P Description External reference frequency input. Connect to externally generated reference signal. Select appropriate frequency range for the intended input frequency (see Table `Modulation Selection') Digital logic input used to select Frequency Range (see Table 1). This pin has an internal pull-up resistor. Digital logic input used to select Modulation Rate (see Table 1). This pin has an internal pull-up resistor. Ground Connection. Connect to system ground. Digital logic input used to enable Spread Spectrum function (Active Low). Spread Spectrum function enable when low. This pin has an internal pulllow resistor. Spread Spectrum Clock Output. Digital logic input used to select Spreading Range (see Table 1). This pin has an internal pull-up resistor. Connect to +3.3V High Frequency LCD Panel EMI Reduction IC Notice: The information in this document is subject to change without notice. 2 of 9 P2160 October 2003 rev E Table-1 Modulation Selection FS0 MRA SR0 Frequency Range Spread Range Modulation Rate 0 0 0 40-80MHz +/- 0.5% (Fin/40) * 34.72 KHz 0 0 1 40-80MHz +/- 1.0% (Fin/40) * 34.72 KHz 0 1 0 40-80MHz +/- 0.5% (Fin/40) * 20.83 KHz 0 1 1 40-80MHz +/- 1.0% (Fin/40) * 20.83 KHz 1 0 0 80-166MHz +/- 0.5% (Fin/80) * 34.72 KHz 1 0 1 80-166MHz +/- 1.00% (Fin/80) * 34.72 KHz 1 1 0 80-166MHz +/- 0.5% (Fin/80) * 20.83 KHz 1 1 1 80-166MHz +/- 1.00% (Fin/80) * 20.83 KHz Spread Spectrum Selection Table 1 illustrates the possible spread spectrum options. The optimal setting should minimize system EMI to the fullest without affecting system performance. The spreading is described as a percentage deviation of the center frequency (Note: the center frequency is the frequency of the external reference input on CLKIN, Pin 1). Example: P2160 is designed for high-resolution flat panel applications and is able to support UXGA (1600 X 1200) flat panel that operates on 162 MHz (Fin) clock speed. A spreading selection of FS0=1, SR0=1 and modulation rate selection MRA=1, enables input frequency range from 80 ~ 166 MHz and provides a percentage deviation of +/-1.00% (see Table 1) of the input frequency (Fin). This results in frequency on ModOUT being swept from 160.38 MHz to 163.62 MHz at a modulation rate of 42.18 KHz (162 MHz/80 MHz X 20.83KHz). This particular example (see below figure) given here is a common EMI reduction method for notebook and LCD monitor manufacturers and has already been implemented by most of the leading OEM and mobile graphic accelerator manufacturers. Application Schematic for Mobile LCD Graphics Controllers High Frequency LCD Panel EMI Reduction IC Notice: The information in this document is subject to change without notice. 3 of 9 P2160 October 2003 rev E EMC Software Simulation By using Alliance Semiconductor's proprietary EMC simulation software - EMI-lator(R), radiated system level EMI analysis can be made easier to allow a quantitative assessment on Alliance's EMI reduction products. The simulation engine of this EMC software has already been characterized to correlate with the electrical characteristics of Alliance EMI reduction IC's. The figure below is an example of the simulation result. Please visit our web site at www.alsc.comfor information on how to obtain a free copy and demonstration of EMI-lator(R). Simulation Result from EMI-lator(R) High Frequency LCD Panel EMI Reduction IC Notice: The information in this document is subject to change without notice. 4 of 9 P2160 October 2003 rev E Absolute Maximum Ratings Symbol VDD, VIN Parameter Voltage on any pin with respect to GND Rating Unit -0.5 to + 7.0 V TSTG Storage temperature -65 to +125 C TA Operating temperature 0 to +70 C DC Electrical Characteristics Symbol Parameter VIL Input Low Voltage VIH Input High Voltage Input Low Current (pull-up resistor on inputs FS0, SR0 and MRA) Input High Current (pull-down resistor on input SSON#) IIL Min Typ Max Unit GND - 0.3 - 0.8 V 2.0 - VDD + 0.3 V - - -35 A - - 35 VOL Output Low Voltage (VDD=3.3V, IOL = 20 mA) - - 0.4 A V VOH Output High Voltage (VDD=3.3V, IOH = 20 mA) 2.5 - - V IDD Static Supply Current, measured @ FS0=0 @ FS0=1 - 3.27 0.67 - mA ICC Dynamic Supply Current FS0=0 (see fIN ) (3.3V and 15 pF loading) FS0=1 (see fIN ) 7.92 10.9 10 16 12.9 22.1 mA VDD Operating Voltage 2.7 3.3 3.8 V tON Power Up Time (First locked clock cycle after power up) IIH ZOUT Clock Output Impedance 0.18 ms 50 AC Electrical Characteristics Symbol fIN tLH* tHL* tJC Parameter Input Frequency when FS0=0 FS0=1 Output rise time (Measured at 0.8V to 2.0V) Output fall time (Measured at 0.8V to 2.0V) Jitter (cycle to cycle) tD Output duty cycle *tLH and tHL are measured into a capacitive load of 15pF Min Typ Max Unit 40 80 65 120 80 166 MHz MHz 0.7 0.9 1.1 ns 0.6 0.8 1.0 ns - - 360 ps 45 50 55 % High Frequency LCD Panel EMI Reduction IC Notice: The information in this document is subject to change without notice. 5 of 9 P2160 October 2003 rev E Package Information Mechanical Package Outline 8-Pin SOIC Symbol Dimensions in inches Dimensions in millimeters Min Nor Max Min Nor Max A 0.057 0.064 0.071 1.45 1.63 1.80 A1 0.004 0.007 0.010 0.10 0.18 0.25 A2 0.053 0.061 0.069 1.35 1.55 1.75 B 0.012 0.016 0.020 0.31 0.41 0.51 C 0.004 0.006 0.01 0.10 0.15 0.25 D 0.186 0.194 0.202 4.72 4.92 5.12 E 0.148 0.156 0.164 3.75 3.95 4.15 e 0.050 BSC 1.27 BSC H 0.224 0.236 0.248 5.70 6.00 6.30 L 0.012 0.020 0.028 0.30 0.50 0.70 a 0 5 8 0 5 8 Note: Controlling dimensions are millimeters SOIC - 0.074 grams unit weight High Frequency LCD Panel EMI Reduction IC Notice: The information in this document is subject to change without notice. 6 of 9 P2160 October 2003 rev E Mechanical Package Outline 8-Pin TSSOP Dimensions in inches Symbol Min Nor A Max Dimensions in millimeters Min Nor 0.047 A1 0.002 A2 0.031 B Max 1.10 0.006 0.05 0.041 0.80 0.007 0.012 0.19 0.30 C 0.004 0.008 0.09 0.20 D 0.114 0.118 0.122 2.90 3.00 3.10 E 0.169 0.173 0.177 4.30 4.40 4.50 e 0.039 0.026 BSC 0.15 1.00 1.05 0.65 BSC H 0.244 0.252 0.260 6.20 6.40 6.60 L 0.018 0.024 0.030 0.45 0.60 0.75 a 0 5 8 0 5 8 Note: Controlling dimensions are millimeters TSSOP - 0.034 grams unit weight High Frequency LCD Panel EMI Reduction IC Notice: The information in this document is subject to change without notice. 7 of 9 P2160 October 2003 rev E Ordering Codes Part Number Marking Package Type P2160A-08ST P2160A 8-pin SOIC, tube P2160A-08SR P2160A 8-pin SOIC, tape & reel P2160A-08TT P2160A 8-pin TSSOP, tube P2160A-08TR P2160A 8-pin TSSOP, tape & reel Qty per reel Temperature (C) 0 to 70 2500 0 to 70 0 to 70 2500 0 to 70 Licensed under US patent Nos 5,488,627 and 5,631,920. Preliminary datasheet. Specification subject to change without notice. High Frequency LCD Panel EMI Reduction IC Notice: The information in this document is subject to change without notice. 8 of 9 P2160 October 2003 rev E Alliance Semiconductor Corporation 2595, Augustine Drive, Santa Clara, CA 95054 Tel# 408-855-4900 Fax: 408-855-4999 www.alsc.com Copyright (c) Alliance Semiconductor All Rights Reserved Part Number: P2160A Document Version: E (c) Copyright 2003 Alliance Semiconductor Corporation. All rights reserved. Our three-point logo, our name and Intelliwatt are trademarks or registered trademarks of Alliance. All other brand and product names may be the trademarks of their respective companies. Alliance reserves the right to make changes to this document and its products at any time without notice. Alliance assumes no responsibility for any errors that may appear in this document. The data contained herein represents Alliance's best data and/or estimates at the time of issuance. Alliance reserves the right to change or correct this data at any time, without notice. If the product described herein is under development, significant changes to these specifications are possible. The information in this product data sheet is intended to be general descriptive information for potential customers and users, and is not intended to operate as, or provide, any guarantee or warrantee to any user or customer. Alliance does not assume any responsibility or liability arising out of the application or use of any product described herein, and disclaims any express or implied warranties related to the sale and/or use of Alliance products including liability or warranties related to fitness for a particular purpose, merchantability, or infringement of any intellectual property rights, except as express agreed to in Alliance's Terms and Conditions of Sale (which are available from Alliance). All sales of Alliance products are made exclusively according to Alliance's Terms and Conditions of Sale. The purchase of products from Alliance does not convey a license under any patent rights, copyrights; mask works rights, trademarks, or any other intellectual property rights of Alliance or third parties. Alliance does not authorize its products for use as critical components in life-supporting systems where a malfunction or failure may reasonably be expected to result in significant injury to the user, and the inclusion of Alliance products in such life-supporting systems implies that the manufacturer assumes all risk of such use and agrees to indemnify Alliance against all claims arising from such use. High Frequency LCD Panel EMI Reduction IC Notice: The information in this document is subject to change without notice. 9 of 9