Teccor Electronics http://www.teccor.com
972-580-7777 - 1
New D-PAK Sensitive
New D-PAK Sensitive SCRs
(4 – 10 Amps)
11
General Descript ion
Teccor 's new line of D-PA K se nsiti ve SCR sem i-con du ctors a re
hal f-w av e , un id i rect i on al , ga te -c ont ro lle d r ec tif i er s.These device s
are off ered with current ratings of 4 -10 amps and voltage ratings
of 100- 600 volts, with thr ee gate s en sitivi ties: 50, 20 0, an d 500
microa mpe res. The se sen sitive SCRs a re very us eful in ap plica-
tions where high gain is required. Gate currents of microamperes
contr ol load current s of s everal amper es.
Teccor ’s D-PAK SC Rs are available in a choice of t wo package s
as shown ab ove, surface mount (SM T ) TO-252AA and throug h
hole TO-251AA. The sturdy built assembled SCRs have copper
connections going directly to the die without any intermediate
wiring.
These SCRs from Teccor Electronics are par t of a broad line of
thyr istor prod uc ts with robust su rge c urre nt ca pabi lities.
This new line of d evices is designed f or high volume, low cost AC
power applicat ions s uc h as con trolle rs for motor load s, tools,
ground fault circuits, alarms, and general line voltage switching.
All Teccor SCRs have glass-passivated junctions to ensure long
term device reliability and permanent stability. Teccor’s glass
offers a rugged , reli able barr ie r aga inst junc tio n conta m ina-
tion.Variati ons of devices covered in this data sheet are available
for cust om desi gn app lic ations. P leas e cons ult factory for more
information.
Tape-a nd-r eel cap ab ility is available for throug h hol e TO-251AA.
The TO-252AA is fur n ishe d in p ocket / embossed t ape on reels.
Features
• Surface mount package TO-252AA and through
hole TO-251AA
• Glass-passivated junctions ensure long device
reliability and parameter stability
• Sensitive gate input
• Voltage capability — up to 600 Volts
• Surge capability — up to 100 Amps
Preliminary
D-PAK
TO-252AA D-PAK
TO-251AA
AK
G
Preliminary Thyristor Product Catalog
http://www.teccor.com Teccor Electronics
- 2 972-580-7777
(OHFWULFDO6SHFLILFDWLRQV
Part No. IT
VDRM &
VRRM IGT IDRM & IRRM VTM VGT
Surface Mount Through Hole
TYPE
Maximum
On-State
Current
(9)
Amps
Repetitive
Peak
Off-State
Forward &
Reverse
Voltage
Volts
DC Gate
Trigger
Current
VD = 6VDC
RL = 100Ω
(5)
µAmps
Peak Off-State
Current
Gate Open
VDRM = Max
Rated Value
(2)
mAmps
Peak
On-State
Voltage at
Max Rat-
ed RMS
Current
TC = 25°C
Volts
DC Gate
Trigger Voltage
VD = 6VDC
RL = 100Ω
(4)
Volts
TO-252AA
D-PAK TO-251AA
D-PAK IT(RMS) IT(AV) TC =
25°CTC =
110°CTC =
40°CTC =
25°CTC =
110°C
Non Isolated Non Isolated MIN MAX MAX MAX MAX MAX MAX MIN
4 Amps
S1004DS1 4.0 2.5 100 50 .002 0.10 2.2 1.0 0.8 0.2
S1004DS2 4.0 2.5 100 200 .002 0.10 2.2 1.0 0.8 0.2
S2004DS1 4.0 2.5 200 50 .002 0.10 2.2 1.0 0.8 0.2
S2004DS2 4.0 2.5 200 200 .002 0.10 2.2 1.0 0.8 0.2
S4004DS1 4.0 2.5 400 50 .002 0.10 2.2 1.0 0.8 0.2
S4004DS2 4.0 2.5 400 200 .002 0.10 2.2 1.0 0.8 0.2
S6004DS1 4.0 2.5 600 50 .002 0.10 2.2 1.0 0.8 0.2
S6004DS2 4.0 2.5 600 200 .002 0.10 2.2 1.0 0.8 0.2
S1004VS1 4.0 2.5 100 50 .002 0.10 2.2 1.0 0.8 0.2
S1004VS2 4.0 2.5 100 200 .002 0.10 2.2 1.0 0.8 0.2
S2004VS1 4.0 2.5 200 50 .002 0.10 2.2 1.0 0.8 0.2
S2004VS2 4.0 2.5 200 200 .002 0.10 2.2 1.0 0.8 0.2
S4004VS1 4.0 2.5 400 50 .002 0.10 2.2 1.0 0.8 0.2
S4004VS2 4.0 2.5 400 200 .002 0.10 2.2 1.0 0.8 0.2
S6004VS1 4.0 2.5 600 50 .002 0.10 2.2 1.0 0.8 0.2
S6004VS2 4.0 2.5 600 200 .002 0.10 2.2 1.0 0.8 0.2
6 Amps
S1006DS2 6.0 3.8 100 200 .005 0.25 1.6 1.0 0.8 0.25
S1006DS3 6.0 3.8 100 500 .005 0.25 1.6 1.0 0.8 0.25
S2006DS2 6.0 3.8 200 200 .005 0.25 1.6 1.0 0.8 0.25
S2006DS3 6.0 3.8 200 500 .005 0.25 1.6 1.0 0.8 0.25
S4006DS2 6.0 3.8 400 200 .005 0.25 1.6 1.0 0.8 0.25
S4006DS3 6.0 3.8 400 500 .005 0.25 1.6 1.0 0.8 0.25
S6006DS2 6.0 3.8 600 200 .005 0.25 1.6 1.0 0.8 0.25
S6006DS3 6.0 3.8 600 500 .005 0.25 1.6 1.0 0.8 0.25
S1006VS2 6.0 3.8 100 200 .005 0.25 1.6 1.0 0.8 0.25
S1006VS3 6.0 3.8 100 500 .005 0.25 1.6 1.0 0.8 0.25
S2006VS2 6.0 3.8 200 200 .005 0.25 1.6 1.0 0.8 0.25
S2006VS3 6.0 3.8 200 500 .005 0.25 1.6 1.0 0.8 0.25
S4006VS2 6.0 3.8 400 200 .005 0.25 1.6 1.0 0.8 0.25
S4006VS3 6.0 3.8 400 500 .005 0.25 1.6 1.0 0.8 0.25
S6006VS2 6.0 3.8 600 200 .005 0.25 1.6 1.0 0.8 0.25
S6006VS3 6.0 3.8 600 500 .005 0.25 1.6 1.0 0.8 0.25
8 Amps
S1008DS2 8.0 5.1 100 200 .005 0.25 1.6 1.0 0.8 0.25
S1008DS3 8.0 5.1 100 500 .005 0.25 1.6 1.0 0.8 0.25
S2008DS2 8.0 5.1 200 200 .005 0.25 1.6 1.0 0.8 0.25
S2008DS3 8.0 5.1 200 500 .005 0.25 1.6 1.0 0.8 0.25
S4008DS2 8.0 5.1 400 200 .005 0.25 1.6 1.0 0.8 0.25
S4008DS3 8.0 5.1 400 500 .005 0.25 1.6 1.0 0.8 0.25
S6008DS2 8.0 5.1 600 200 .005 0.25 1.6 1.0 0.8 0.25
S6008DS3 8.0 5.1 600 500 .005 0.25 1.6 1.0 0.8 0.25
S1008VS2 8.0 5.1 100 200 .005 0.25 1.6 1.0 0.8 0.25
S1008VS3 8.0 5.1 100 500 .005 0.25 1.6 1.0 0.8 0.25
S2008VS2 8.0 5.1 200 200 .005 0.25 1.6 1.0 0.8 0.25
S2008VS3 8.0 5.1 200 500 .005 0.25 1.6 1.0 0.8 0.25
S4008VS2 8.0 5.1 400 200 .005 0.25 1.6 1.0 0.8 0.25
S4008VS3 8.0 5.1 400 500 .005 0.25 1.6 1.0 0.8 0.25
S6008VS2 8.0 5.1 600 200 .005 0.25 1.6 1.0 0.8 0.25
S6008VS3 8.0 5.1 600 500 .005 0.25 1.6 1.0 0.8 0.25
Thyristor Product Catalog Preliminary
Teccor Electronics http://www.teccor.com
972-580-7777 - 3
New D-PAK Sensitive
IHIGM VGRM PGM PG(AV) ITSM dv/dt di/dt tgt tqI2t
Holding
Current
Gate Open
Initial on State
Current =
20mA
(6)
mAmps
Peak
Gate
Current
(1)
Amps
Peak
Reverse
Gate
Voltage
Volts
Peak
Gate
Power
Dissipa-
tion
(1)
Watts
Average
Gate
Power
Dissipa-
tion
Watts
Peak
One
Cycle
Surge
(3)(7)(9)
Amps
Critical Rate-of-
Applied V oltage
Volts/µSec
Maximum
Rate-of-
Change of
On-State
Current
IGT = 150mA
With 0.1µs
Rise Tim e
Amps/µSec
Gate
Controlled
Turn-OnTime
Gate
Pulse=10mA
Min.
Width=15µs
≤ 0.1µs
Rise Time
µSec
Circuit
Commulated
Turn-Off
Time
(8)
µSec
RMS Surge
(Non-
Repetitive)
On-State
Current
for Period of
8.3ms
for Fusing
Amps2Sec60Hz 50Hz TC =
110°C
MAX MIN TYP TYP MAX
4.0 1.0 6.0 1.0 0.1 20 16 850 3.0 50 1.6
6.0 1.0 6.0 1.0 0.1 20 16 850 4.0 50 1.6
4.0 1.0 6.0 1.0 0.1 20 16 850 3.0 50 1.6
6.0 1.0 6.0 1.0 0.1 20 16 850 4.0 50 1.6
4.0 1.0 6.0 1.0 0.1 20 16 850 3.0 50 1.6
6.0 1.0 6.0 1.0 0.1 20 16 850 4.0 50 1.6
4.0 1.0 6.0 1.0 0.1 20 16 850 3.0 50 1.6
6.0 1.0 6.0 1.0 0.1 20 16 850 4.0 50 1.6
4.0 1.0 6.0 1.0 0.1 20 16 850 3.0 50 1.6
6.0 1.0 6.0 1.0 0.1 20 16 850 4.0 50 1.6
4.0 1.0 6.0 1.0 0.1 20 16 850 3.0 50 1.6
6.0 1.0 6.0 1.0 0.1 20 16 850 4.0 50 1.6
4.0 1.0 6.0 1.0 0.1 20 16 850 3.0 50 1.6
6.0 1.0 6.0 1.0 0.1 20 16 850 4.0 50 1.6
4.0 1.0 6.0 1.0 0.1 20 16 850 3.0 50 1.6
6.0 1.0 6.0 1.0 0.1 20 16 850 4.0 50 1.6
6.0 1.0 6.0 1.0 0.1 100 83 10 100 4.0 50 41
8.0 1.0 6.0 1.0 0.1 100 83 10 100 5.0 45 41
6.0 1.0 6.0 1.0 0.1 100 83 10 100 4.0 50 41
8.0 1.0 6.0 1.0 0.1 100 83 10 100 5.0 45 41
6.0 1.0 6.0 1.0 0.1 100 83 8 100 4.0 50 41
8.0 1.0 6.0 1.0 0.1 100 83 8 100 5.0 45 41
6.0 1.0 6.0 1.0 0.1 100 83 8 100 4.0 50 41
8.0 1.0 6.0 1.0 0.1 100 83 8 100 5.0 45 41
6.0 1.0 6.0 1.0 0.1 100 83 10 100 4.0 50 41
8.0 1.0 6.0 1.0 0.1 100 83 10 100 5.0 45 41
6.0 1.0 6.0 1.0 0.1 100 83 10 100 4.0 50 41
8.0 1.0 6.0 1.0 0.1 100 83 10 100 5.0 45 41
6.0 1.0 6.0 1.0 0.1 100 83 8 100 4.0 50 41
8.0 1.0 6.0 1.0 0.1 100 83 8 100 5.0 45 41
6.0 1.0 6.0 1.0 0.1 100 83 8 100 4.0 50 41
8.0 1.0 6.0 1.0 0.1 100 83 8 100 5.0 45 41
6.0 1.0 6.0 1.0 0.1 100 83 10 100 4.0 50 41
8.0 1.0 6.0 1.0 0.1 100 83 10 100 5.0 45 41
6.0 1.0 6.0 1.0 0.1 100 83 10 100 4.0 50 41
8.0 1.0 6.0 1.0 0.1 100 83 10 100 5.0 45 41
6.0 1.0 6.0 1.0 0.1 100 83 8100 4.0 50 41
8.0 1.0 6.0 1.0 0.1 100 83 8100 5.0 45 41
6.0 1.0 6.0 1.0 0.1 100 83 8100 4.0 50 41
8.0 1.0 6.0 1.0 0.1 100 83 8100 5.0 45 41
6.0 1.0 6.0 1.0 0.1 100 83 10 100 4.0 50 41
8.0 1.0 6.0 1.0 0.1 100 83 10 100 5.0 45 41
6.0 1.0 6.0 1.0 0.1 100 83 10 100 4.0 50 41
8.0 1.0 6.0 1.0 0.1 100 83 10 100 5.0 45 41
6.0 1.0 6.0 1.0 0.1 100 83 8100 4.0 50 41
8.0 1.0 6.0 1.0 0.1 100 83 8100 5.0 45 41
6.0 1.0 6.0 1.0 0.1 100 83 8100 4.0 50 41
8.0 1.0 6.0 1.0 0.1 100 83 8100 5.0 45 41
Preliminary Thyristor Product Catalog
http://www.teccor.com Teccor Electronics
- 4 972-580-7777
(OHFWULFDO6SHFLILFDWLRQV
Electrical Specificati on Notes
(1) Pulse width ≤ 10µs.
(2) TC = TJ for test conditions in off-state.
(3) For more than one full cycle rating, see Figure 1.2
(4) See Figure 1.1 for VGT vs TC
(5) See Figure 1.6 for IGT vs TC
(6) See Figure 1.5 for IH vs TC
(7) 4.0A devices also have a pulse peak forward current on-state rat-
ing (repetitive) of 75A. This rating applies for operation at 60Hz,
75°C maximum tab (or anode) lead temperature, switching from
80V peak, sinusoidal current pulse width of 10µs minimum, 15 µs
maximum.
(8) Test conditions as follows:
TC ≤ 80°C, rectangular current waveform; rate-of-rise of current
≤10A/µs. Rate-of-reversa l of current ≤ 5A/µs. ITM = 1A (50µs
pulse) Repetition Rate = 60pps. VRRM = Rated. VR = 15V mini-
mum, VDRM = Rated. Rate-of-rise reapplied forward blocking volt-
age = 5V/µs. Gate Bias = 0V, 100Ω (during turn-off time interval)
(9) See Figure 1.3 and 1.4 for current rating at specified operating
case temperature.
General Notes
•All measurements are made at 60Hz with a resistive load at an
ambient temperature of +25°C unless otherwise specified.
•Operating temperature range (TJ) is -40°C to +110 °C
•Storage temperature range (TS) is -65°C to +150°C
•Lead solder temperature is a maximum of 230°C for 10 seconds
maximum; 1/16" (1.59mm) from case.
•The case temperature (TC) is measured as shown on dimensional
outline drawings. See mechanical specifications on page 6 of this
data sheet.
Figure 1.1 Norm alized DC Gate-Trigger Vo ltage vs Case Temperature
Figure 1.2 Peak Surge Current vs Surge Current Duration
Part No. IT
VDRM &
VRRM IGT IDRM & IRRM VTM VGT
Surface Mount Through Hole
TYPE
Maximum
On-State
Current
(9)
Amps
Repetitive
Peak
Off-State
Forward &
Reverse
Voltage
Volts
DC Gate
Trigger
Current
VD = 6VDC
RL = 100Ω
(5)
mAmps
Peak Off-State
Current
Gate Open
VDRM = Ma x
Rated Va lu e
(2)
mAmps
Peak
On-State
Voltage at
Max Rat-
ed RMS
Current
TC = 25°C
Volts
DC Gate
Trigger Voltage
VD = 12VDC
RL = 60Ω
(4)
Volts
TO-252AA
D-PAK TO-251AA
D-PAK IT(RMS) IT(AV) TC =
25°CTC =
110°CTC =
-40°CTC =
25°CTC =
110°C
Non Isolated Non Isolate d MIN M A X MA X MAX MAX MAX MAX MIN
10 Amps
S1010DS2 10.0 6.4 100 200 .005 0.25 1.6 1.0 0.8 0.25
S1010DS3 10.0 6.4 100 500 .005 0.25 1.6 1.0 0.8 0.25
S2010DS2 10.0 6.4 200 200 .005 0.25 1.6 1.0 0.8 0.25
S2010DS3 10.0 6.4 200 500 .005 0.25 1.6 1.0 0.8 0.25
S4010DS2 10.0 6.4 400 200 .005 0.25 1.6 1.0 0.8 0.25
S4010DS3 10.0 6.4 400 500 .005 0.25 1.6 1.0 0.8 0.25
S6010DS2 10.0 6.4 600 200 .005 0.25 1.6 1.0 0.8 0.25
S6010DS3 10.0 6.4 600 500 .005 0.25 1.6 1.0 0.8 0.25
S1010VS2 10.0 6.4 100 200 .005 0.25 1.6 1.0 0.8 0.25
S1010VS3 10.0 6.4 100 500 .005 0.25 1.6 1.0 0.8 0.25
S2010VS2 10.0 6.4 200 200 .005 0.25 1.6 1.0 0.8 0.25
S2010VS3 10.0 6.4 200 500 .005 0.25 1.6 1.0 0.8 0.25
S4010VS2 10.0 6.4 400 200 .005 0.25 1.6 1.0 0.8 0.25
S4010VS3 10.0 6.4 400 500 .005 0.25 1.6 1.0 0.8 0.25
S6010VS2 10.0 6.4 600 200 .005 0.25 1.6 1.0 0.8 0.25
S6010VS3 10.0 6.4 600 500 .005 0.25 1.6 1.0 0.8 0.25
-40 -15 +25 +65 +105 +125
0
.5
1.0
1.5
Case Temperature (TC) - ˚C
Ratio of VGT
VGT (TC = 25˚C)
8
1
2
3
4
5
6
10
20
30
40
50
60
80
100
123 54 6 7 8 10 20 30 40 60 80 100 200 300 400 600 1000
Surge Current Duration - Full Cycles
10 AMP DEVICES
SUPPLY FREQUENCY: 60 Hz Sinusoidal
LOAD: Resistive
RMS ON-STATE CURRENT: [IT(RMS)]: Max-
Rated Value at Specified Case Temperature
GATE CONTROL MAY BE LOST
DURING AND IMMEDIATELY
FOLLOWING SURGE CURRENT
INTERVAL.
OVERLOAD MAY NOT BE REPEATED
UNTIL JUNCTION TEMPERATURE
HAS RETURNED TO STEADY-STATE
RATED VALUE.
8 AMP DEVICES
6 AMP DEVICES
4 AMP DEVICES
Thyristor Product Catalog Preliminary
Teccor Electronics http://www.teccor.com
972-580-7777 - 5
New D-PAK Sensitive
Figure 1.3 Maximum Allowable Case Tem peratrue vs RMS On-State
Current Figure 1.4 Maximum Allowable Case Temperatrue v s Average On-
State Current
IHIGM VGRM PGM PG(AV) ITSM dv/dt di/dt tgt tqI2t
Holding
Current
Gate Open
Initial on State
Current =
20mA
(6)
mAmps
Peak
Gate
Current
(1)
Amps
Peak
Reverse
Gate
Voltage
Volts
Peak
Gate
Power
Dissipa-
tion
(1)
Watts
Average
Gate
Power
Dissipa-
tion
Watts
Peak
One
Cycle
Surge
(3)(9)
Amps
Critical Rate-of-
Applied V oltage
Volts/µSec
Maximum
Rate-of-
Change of
On-State
Current
IGT = 150mA
With 0.1µs
Rise Time
Amps/µSec
Gate
Controlled
Turn-OnTime
Gate
Pulse=100mA
Min.
Width=15µs
IGT = 50mA
≤ 0.1µs
Rise Tim e
µSec
Circuit
Commulated
Turn-Off
Time
(8)
µSec
RMS Surge
(Non-
Repetitive)
On-State
Current
for Period of
8.3ms
for Fusing
Amps2Sec60Hz 50Hz TC =
110°C
MAX MIN TYP TYP MAX
6.0 1.0 6.0 1.0 0.1 100 83 10 100 4.0 50 41
8.0 1.0 6.0 1.0 0.1 100 83 10 100 5.0 45 41
6.0 1.0 6.0 1.0 0.1 100 83 10 100 4.0 50 41
8.0 1.0 6.0 1.0 0.1 100 83 10 100 5.0 45 41
6.0 1.0 6.0 1.0 0.1 100 83 8100 4.0 50 41
8.0 1.0 6.0 1.0 0.1 100 83 8100 5.0 45 41
6.0 1.0 6.0 1.0 0.1 100 83 8100 4.0 50 41
8.0 1.0 6.0 1.0 0.1 100 83 8100 5.0 45 41
6.0 1.0 6.0 1.0 0.1 100 83 10 100 4.0 50 41
8.0 1.0 6.0 1.0 0.1 100 83 10 100 5.0 45 41
6.0 1.0 6.0 1.0 0.1 100 83 10 100 4.0 50 41
8.0 1.0 6.0 1.0 0.1 100 83 10 100 5.0 45 41
6.0 1.0 6.0 1.0 0.1 100 83 8100 4.0 50 41
8.0 1.0 6.0 1.0 0.1 100 83 8100 5.0 45 41
6.0 1.0 6.0 1.0 0.1 100 83 8100 4.0 50 41
8.0 1.0 6.0 1.0 0.1 100 83 8100 5.0 45 41
02 4681012
50
60
70
80
90
100
110
120
130
CURRENT WAVEFORM: Sinusoidal
LOAD: Resistive or Inductive
CONDUCTION ANGLE: 180º
CASE TEMPERATURE: Measure as
shown on dimensional drawings
RMS On-State Current [IT(RMS)] - Amps
Maximum Allowable
Case Temperature (TC) - ˚C
8 AMP
10 AMP
4 AMP
6 AMP
02468
50
60
70
80
90
100
110
120
130
Average On-State Current [IT(AV)] - Amps
Maximum Allowable
Case Temperature (TC) - ˚C
8 AMP
6 AMP
10 AMP
4 AMP
CURRENT WAVEFORM: Sinusoidal
LOAD: Resistive or Inductive
CONDUCTION ANGLE: 180º
CASE TEMPERATURE: Measure as
shown on dimensional drawings
Preliminary Thyristor Product Catalog
http://www.teccor.com Teccor Electronics
- 6 972-580-7777
0HFKDQLFDO6SHFLILFDWLRQV
TO -252AA D-PAK Surface Mount
Figure 1.5 Normalized DC Holding Current vs Case Temperature
TO-251AA D-PAK Through Hole
Figure 1.6 Norm alized DC Gate - Trigger Current vs Case
Temperature
DIM INCHES MILLIMETERS
MIN MAX MIN MAX
A.236 .244 6.00 6.20
B.379 .409 9.63 10.39
C.176 .184 4.47 4.67
D.035 .050 0.89 1.27
E.087 .093 2.21 2.36
F.027 .033 0.69 0.84
G.205 .213 5.21 5.41
H.251 .261 6.38 6.63
J.040 .050 1.02 1.27
K.086 .094 2.18 2.39
L.026 .036 0.66 0.91
M.018 .023 0.46 0.58
N.170 .180 4.32 4.57
O.002 .010 0.05 0.25
P.018 .023 0.46 0.58
-65 -40 -15 +25 +65 +110 +125
0
1.0
2.0
3.0
4.0 See General Notes for specific
operating temperature range.
Case Temperature (TC) - ˚C
Ratio of IH
IH(TC = 25˚C)
DIM INCHES MILLIMETERS
MIN MAX MIN MAX
A.040 .050 1.02 1.27
B.236 .244 6.00 6.20
C.350 .375 8.89 9.53
D.205 .213 5.21 5.41
E.251 .261 6.38 6.63
F.027 .033 0.69 0.84
G.087 .093 2.21 2.36
H.086 .094 2.18 2.39
J.018 .023 0.46 0.58
K.036 .042 0.91 1.07
L.018 .023 0.46 0.58
-65 -15 +25 +65 +110 +125-40
0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
Case Temperature (TC) - ˚C
Ratio of IGT
I
GT
(TC = 25˚C)
See General Notes for specific device
operating temperature range.