Q14 series -Q D IN LED INDICATORS 07 18 14 O14 mm panel mount LED indicators DISTINCTIVE FEATURES 10 mm colored diffused epoxy lens or 10 mm water clear super bright LEDs Prominent and flush bezel styles (2.8 x 0.8) solder lug/faston terminals, pins or (200 mm long) wire terminations Custom engraving available ENVIRONMENTAL SPECIFICATIONS * IP67 sealing option (EN60529) * Operating & Storage Temperature Range: Rear plastic body: -30 C to +65 C ( -22 F to +149 F) Rear epoxy body: -40 C to +85 C ( -40 F to +185 F) GENERAL SPECIFICATIONS * Max Reverse Voltage: 5 V * Viewing Angle: 30-100 (dependant on model) * Life Expectancy: 100,000 hours * Torque: 4 cNm (dependent on option) * Maximum panel thickness 11 mm MATERIALS * Plated brass bezel finished in bright chrome, black or satin grey and moulded polycarbonate rear body MOUNTING The company reserves the right to change specifications without notice. All LED characteristics are dependent upon environmental conditions. Therefore published data should be considered nominal and subject to variations. 1 LED INDICATORS Q14 series O14 mm panel mount LED indicators ELECTRICAL SPECIFICATIONS Voltage STANDARD LED INTENSITY LED COMPONENT SPECIFICATIONS Operating Current (Min to Max) (Typical All Types) Prominent and Recessed Flush Forward Voltage 02 (No Resistor) 1.8 to 3.3 VDC 20 mA max HE Red 80 mcd 10 mcd 2.0 V 6 VDC 5.4 to 6.6 VDC 20 mA Green 60 mcd 5 mcd 2.2 V 12 VDC 10.8 to 13.2 VDC 20 mA 24 VDC 21.6 to 26.4 VDC 20 mA Yellow 50 mcd 4 mcd 2.1 V Blue 540 mcd 100 mcd 3.3 V White 1000 mcd 150 mcd 3.3 V Orange 80 mcd 200 mcd 2.2 V Bi-color (Typical) (Red/Green) 15/15 mcd 14/10 mcd 2.0V/2.2 V Tri-color (Typical) (Red/Green/Yellow) 60/50/50mcd 15/10/30 mcd 2.0 V/2.2 V/2.1 V Bi-color - The color is changed by reversing the polarity of the supply voltage. Tri-color - The indicator has red and green LEDs, when both connected yellow is produced. SUPER BRIGHT LED INTENSITY LED COMPONENT SPECIFICATIONS Prominent and Recessed Flush Forward Voltage HE Red 17,000 mcd 2,000 mcd 2.2 V Green 11,000 mcd 680 mcd 3.3 V Yellow 4,000 mcd 350 mcd 2.0 V Blue 2,500mcd 250 mcd 3.3 V White 4,400 mcd 250 mcd 3.3 V Orange 2,800 mcd 300 mcd 2.2 V HYPER BRIGHT LED INTENSITY LED COMPONENT SPECIFICATIONS HE Red Prominent and Recessed Flush Forward Voltage 2,800 mcd 800 mcd 2.1 V Green 2,200 mcd 250 mcd 3.2 V Yellow 1,300 mcd 250 mcd 2.0 V Orange 850 mcd 200 mcd 2.1 V * The operating voltage must not be exceeded by more that 10% as this will result in reduced life expectancy * Luminous intensity is measured at 20 mA on a discrete led unless otherwise stated. * Luminous intensities and color shades of white LEDs may vary within a batch. * Luminous intensity will be reduced with lower operating current. 2 Operating Voltage 28 VDC 25.2 to 30.8 VDC 20 mA 110 VAC 99 to 121 VAC 6 mA 220 VAC 207 to 235 VAC 3 mA * Customer to supply resistor for desired operating current. O14 mm panel mount LED indicators BUILD YOUR PART NUMBER Q SERIES TERMINALS MOUNTING HOLE 14 O14mm BEZEL STYLE P Prominent R Recessed F Flush 1 Solder Lug/ Fastons (2.8 x 0.8) 2 Pins 3 Wires 4 Rear epoxy Pins BEZEL FINISH 5 Rear epoxy Wires 6 Short body Pins 7 Short body Wires ANODIZED FLUSH XX Fixed Light R Red KK Flashing Light (12V - 28VDC) G Green YY Bi-color Y Yellow ZZ Tri-color B Blue W White O Orange HR Hyper Bright Red B Black AY Yellow G Satin Grey AB Blue AN Black 12VDC Hyper Bright Yellow SW Super Bright White HO Hyper Bright Orange RG Red/Green RY 12A Red/Yellow GY 24 Green/Yellow SY Green 12 HY Super Bright Yellow AG 6VDC Super Bright Blue SG Bright Chrome 06 SB Super Bright Green C no resistor Hyper Bright Green Super Bright Red Red 02 HG SR AR VOLTAGE LED COLOR TYPE OF ILLUMINATION OTHERS RYG Red/Yellow/ Green ABOUT THIS SERIES 24A 28 SEALING (Blank) E Unsealed IP67 12VAC/DC 24VDC 24VAC/DC 28VDC 28A 28VAC/DC 110 110VAC 220 220VAC Notice: please note that not all combinations of above numbers are available. * Gold faston terminal denotes anode (+), silver terminal denotes cathode (-) * Take care when soldering to the faston terminals (recommended solder temperature 300 C - 3 sec) * Standard wire length is 200 mm, 22 AWG UL1061, red wire denotes anode (+), black wire denotes cathode (-) for other wire lengths consult APEM * Short body pins and wires are only available up to 28 VDC * For LEDs with alternative voltages and mutlit-voltage options consult APEM * Standard tri-color faston terminals are two anodes (+) and one cathode (-) * 110 VAC and 220 VAC, short body terminal options, 5, 6 and 7 please consult the factory * Bi-color leds, by connecting the gold faston (+) one color is produced, by reversing the supply voltage another color is produced - bi-colors are available up to 28 VDC * The Tri-color LED has red and green LEDs when both are connected yellow is produced * Tri-color wires are one red (+) and one green (+) anode and one black (-) cathode * Tri-color pins are center (-) cathode, shortest (+) anode pin green, longest (+) anode pin red * We recommend using Hyperbright or Superbright LEDs for use at 110 VAC and 220 VAC 3 LED INDICATORS Q14 series LED INDICATORS Q14 series O14 mm panel mount LED indicators PROMINENT BEZEL SOLDER LUG/FASTON WIRES PINS REAR EPOXY WIRES REAR EPOXY PINS SHORT BODY WIRES SHORT BODY PINS 4 O14 mm panel mount LED indicators FLUSH BEZEL SOLDER LUG/FASTON WIRES PINS REAR EPOXY WIRES REAR EPOXY PINS SHORT BODY WIRES SHORT BODY PINS 5 LED INDICATORS Q14 series LED INDICATORS Q14 series O14 mm panel mount LED indicators RECESSED BEZEL SOLDER LUG/FASTON WIRES PINS REAR EPOXY WIRES REAR EPOXY PINS SHORT BODY WIRES SHORT BODY PINS 6 O14 mm panel mount LED indicators CUSTOM ENGRAVING Some common codes are listed above, for your custom requirements please contact APEM. Unless specified standard engraving with white infill will be supplied. Suffix the part number with legend code : High beam -0AJ Low beam -097 Rear fog -027 Front fog -026 Windscreen wiper -021 Windscreen washer -022 Ventilator fan -023 Turn Signal -0AH Side lights -098 Horn -041 Hazard warning -013 Heating -018 Brake test -0BU Arrow -0K6 USB connection -0UB ABS Battery -0AG Oil can -0GP Windscreen heating -020 ABS -086 Engine coil -0EL Seat belt -0SB Side step -0AD Air con -012 Engine -040 Boot/Trunk Release -0BR ECU Steam -0ST ECU -0EU CABLE LENGTH AND CONNECTOR For custom cable length and connectors contact APEM. 7 LED INDICATORS Q14 series