2010 Microchip Technology Inc. Preliminary DS22067H-page 1
11AA010/11LC010 11AA080/11LC080
11AA020/11LC020 11AA160/11LC160
11AA040/11LC040 11AA161/11LC161
Features:
• Single I/O, UNI/O® Serial Interface Bus
• Low-Power CMOS Technology:
- 1 mA active current, typical
- 1 µA standby current (max.) (I-temp)
• 128 x 8 through 2,048 x 8 Bit Organizations
• Schmitt Trigger Inputs for Noise Suppression
• Output Slope Control to Eliminate Ground Bounce
• 100 kbps Max. Bit Rate – Equivalent to 100 kHz
Clock Frequency
• Self-Timed Write Cycle (including Auto-Erase)
• Page-Write Buffer for up to 16 Bytes
• STATUS Register for Added Control:
- Write enable latch bit
- Write-In-Progress bit
• Block Write Protection:
- Protect none, 1/4, 1/2 or all of array
• Built-in Write Protection:
- Power-on/off data protection circuitry
- Write enable latch
• High Reliability:
- Endurance: 1,000,000 erase/write cycles
- Data retention: > 200 years
- ESD protection: > 4,000V
• 3-lead SOT-23 and TO-92 Packages
• 4-lead Chip Scale Package
• 8-lead PDIP, SOIC, MSOP, TDFN Packages
• Pb-Free and RoHS Compliant
• Available Temperature Ranges:
Pin Function Table
Description:
The Microchip Technology Inc. 11AAXXX/11LCXXX
(11XX*) devices are a family of 1 Kbit through 16 Kbit
Serial Electrically Erasable PROMs. The devices are
organized in blocks of x8-bit memory and support the
patented** single I/O UNI/O® serial bus. By using
Manchester encoding techniques, the clock and data
are combined into a single, serial bit stream (SCIO),
where the clock signal is extracted by the receiver to
correctly decode the timing and value of each bit.
Low-voltage design permits operation down to 1.8V (for
11AAXXX devices), with standby and active currents of
only 1 uA and 1 mA, respectively.
The 11XX family is available in standard packages
including 8-lead PDIP and SOIC, and advanced pack-
aging including 3-lead SOT-23, 3-lead TO-92, 4-lead
Chip Scale, 8-lead TDFN, and 8-lead MSOP.
Package Types (not to scale)
- Industrial (I): -40°C to +85°C
- Automotive (E): -40°C to +125°C
Name Function
SCIO Serial Clock, Data Input/Output
VSS Ground
VCC Supply Voltage
NC
NC
NC
Vss
1
2
3
4
8
7
6
5
VCC
NC
NC
SCIO
PDIP/SOIC
(P, SN)
NC
NC
NC
V
SS
1
2
3
4
8
7
6
5
VCC
NC
NC
SCIO
(MS)
TDFN
NC
NC
NC
VSS
NC
NC
SCIO
5
6
7
8
4
3
2
1VCC
(MN)
MSOP
SOT23
2
3
1SCIO
VCC
VSS
(TT)
Vcc
TO-92
SCIO
(TO) 12
34
VCC VSS
NC
SCIO
(Top down view,
balls not visible
)
Note 1: Available in I-temp, “AA” only.
Vss
CS (Chip Scale)(1)
1K-16K UNI/O® Serial EEPROM Family Data Sheet
* 11XX is used in this document as a generic part number for the 11 series devices.
** Microchip’s UNI/O® Bus products are covered by the following patent issued in the U.S.A.: 7,376,020.
11AAXXX/11LCXXX
DS22067H-page 2 Preliminary 2010 Microchip Technology Inc.
DEVICE SELECTION TABLE
Part Number Density
(bits) Organization VCC Range Page Size
(Bytes)
Temp.
Ranges
Device
Address Packages
11LC010 1K 128 x 8 2.5-5.5V 16 I,E 0xA0 P, SN, MS, MN, TO, TT
11AA010 1K 128 x 8 1.8-5.5V 16 I 0xA0 P, SN, MS, MN, TO, TT, CS
11LC020 2K 256 x 8 2.5-5.5V 16 I,E 0xA0 P, SN, MS, MN, TO, TT
11AA020 2K 256 x 8 1.8-5.5V 16 I 0xA0 P, SN, MS, MN, TO, TT, CS
11LC040 4K 512 x 8 2.5-5.5V 16 I,E 0xA0 P, SN, MS, MN, TO, TT
11AA040 4K 512 x 8 1.8-5.5V 16 I 0xA0 P, SN, MS, MN, TO, TT, CS
11LC080 8K 1,024 x 8 2.5-5.5V 16 I,E 0xA0 P, SN, MS, MN, TO, TT
11AA080 8K 1,024 x 8 1.8-5.5V 16 I 0xA0 P, SN, MS, MN, TO, TT, CS
11LC160 16K 2,048 x 8 2.5-5.5V 16 I,E 0xA0 P, SN, MS, MN, TO, TT
11AA160 16K 2,048 x 8 1.8-5.5V 16 I 0xA0 P, SN, MS, MN, TO, TT,CS
11LC161 16K 2,048 x 8 2.5-5.5V 16 I, E 0xA1 P, SN, MS, MN, TO, TT
11AA161 16K 2,048 x 8 1.8-5.5V 16 I 0xA1 P, SN, MS, MN, TO, TT, CS
2010 Microchip Technology Inc. Preliminary DS22067H-page 3
11AAXXX/11LCXXX
1.0 ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings (†)
VCC.............................................................................................................................................................................6.5V
SCIO w.r.t. VSS.....................................................................................................................................-0.6V to VCC+1.0V
Storage temperature ................................................................................................................................. -65°C to 150°C
Ambient temperature under bias............................................................................................................... -40°C to 125°C
ESD protection on all pins.......................................................................................................................................... 4 kV
TABLE 1-1: DC CHARACTERISTICS
† NOTICE: Stresses above those listed under ‘Absolute Maximum Ratings’ may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for an
extended period of time may affect device reliability.
DC CHARACTERISTICS
Electrical Characteristics:
Industrial (I): VCC = 2.5V to 5.5V TA = -40°C to +85°C
VCC = 1.8V to 2.5V TA = -20°C to +85°C
Automotive (E): VCC = 2.5V to 5.5V TA = -40°C to +125°C
Param.
No. Sym. Characteristic Min. Max. Units Test Conditions
D1 VIH High-level input
voltage
0.7*VCC VCC+1 V
D2 VIL Low-level input
voltage
-0.3
-0.3
0.3*VCC
0.2*VCC
V
V
VCC2.5V
VCC < 2.5V
D3 VHYS Hysteresis of Schmitt
Trigger inputs (SCIO)
0.05*Vcc — V VCC2.5V (Note 1)
D4 VOH High-level output
voltage
VCC -0.5
VCC -0.5
—
—
V
V
IOH = -300 A, VCC = 5.5V
IOH = -200 A, Vcc = 2.5V
D5 VOL Low-level output
voltage
—
—
0.4
0.4
V
V
IOI = 300 A, VCC = 5.5V
IOI = 200 A, Vcc = 2.5V
D6 IOOutput current limit
(Note 2)
—
—
±4
±3
mA
mA
VCC = 5.5V (Note 1)
Vcc = 2.5V (Note 1)
D7 ILI Input leakage current
(SCIO)
—±1AVIN = VSS or VCC
D8 CINT Internal Capacitance
(all inputs and
outputs)
—7pFT
A = 25°C, FCLK = 1 MHz,
VCC = 5.0V (Note 1)
D9 ICC Read Read Operating
Current
—
—
3
1
mA
mA
VCC=5.5V; FBUS=100 kHz, CB=100 pF
VCC=2.5V; FBUS=100 kHz, CB=100 pF
D10 ICC Write Write Operating
Current
—
—
5
3
mA
mA
VCC = 5.5V
VCC = 2.5V
D11 Iccs Standby Current —
—
5
1
A
A
VCC = 5.5V
TA = 125°C
VCC = 5.5V
TA = 85°C
D12 ICCI Idle Mode Current — 50 AVCC = 5.5V
Note 1: This parameter is periodically sampled and not 100% tested.
2: The SCIO output driver impedance will vary to ensure IO is not exceeded.
11AAXXX/11LCXXX
DS22067H-page 4 Preliminary 2010 Microchip Technology Inc.
TABLE 1-3: AC TEST CONDITIONS
TABLE 1-2: AC CHARACTERISTICS
AC CHARACTERISTICS
Electrical Characteristics:
Industrial (I): VCC = 2.5V to 5.5V TA = -40°C to +85°C
VCC = 1.8V to 2.5V TA = -20°C to +85°C
Automotive (E): VCC = 2.5V to 5.5V TA = -40°C to +125°C
Param.
No. Sym. Characteristic Min. Max. Units Test Conditions
1F
BUS Serial bus frequency 10 100 kHz —
2T
EBit period 10 100 µs —
3TIJIT Input edge jitter tolerance — ±0.08 UI (Note 3)
4FDRIFT Serial bus frequency drift
rate tolerance
— ±0.75 % per byte —
5F
DEV Serial bus frequency drift
limit
—±5% per
command
—
6T
OJIT Output edge jitter — ±0.25 UI (Note 3)
7TRSCIO input rise time
(Note 1)
— 100 ns —
8T
FSCIO input fall time
(Note 1)
— 100 ns —
9T
STBY Standby pulse time 600 — µs —
10 T
SS Start header setup time 10 — µs —
11 THDR Start header low pulse
time
5—µs—
12 T
SP Input filter spike
suppression (SCIO)
—50ns(Note 1)
13 TWC Write cycle time
(byte or page)
—
—
5
10
ms
ms
Write, WRSR commands
ERAL, SETAL commands
14 — Endurance (per page) 1M — cycles 25°C, VCC = 5.5V (Note 2)
Note 1: This parameter is periodically sampled and not 100% tested.
2: This parameter is not tested but ensured by characterization. For endurance estimates in a specific
application, please consult the Total Endurance™ Model which can be obtained on Microchip’s web site:
www.microchip.com.
3: A Unit Interval (UI) is equal to 1-bit period (TE) at the current bus frequency.
AC Waveform:
VLO = 0.2V
VHI = VCC - 0.2V
CL = 100 pF
Timing Measurement Reference Level
Input 0.5 VCC
Output 0.5 VCC
2010 Microchip Technology Inc. Preliminary DS22067H-page 5
11AAXXX/11LCXXX
FIGURE 1-1: BUS TIMING – START HEADER
FIGURE 1-2: BUS TIMING – DATA
FIGURE 1-3: BUS TIMING – STANDBY PULSE
FIGURE 1-4: BUS TIMING – JITTER
SCIO
2
Data ‘0’Data ‘1’Data ‘0’Data ‘1’Data ‘0’Data ‘1’Data ‘0’Data ‘1’MAK bit NoSAK bit
1110
2
SCIO
7 8
Data ‘0’Data ‘1’Data ‘1’Data ‘0’
12
SCIO
9
Standby
Mode
Ideal Edge
3
2
3 6 6
2
6 6
Ideal Edge Ideal Edge Ideal Edge
from Master from Master from Slave from Slave
11AAXXX/11LCXXX
DS22067H-page 6 Preliminary 2010 Microchip Technology Inc.
2.0 FUNCTIONAL DESCRIPTION
2.1 Principles of Operation
The 11XX family of serial EEPROMs support the
UNI/O® protocol. They can be interfaced with
microcontrollers, including Microchip’s PIC® microcon-
trollers, ASICs, or any other device with an available
discrete I/O line that can be configured properly to
match the UNI/O protocol.
The 11XX devices contain an 8-bit instruction register.
The devices are accessed via the SCIO pin.
Table 4-1 contains a list of the possible instruction
bytes and format for device operation. All instructions,
addresses, and data are transferred MSb first, LSb
last.
Data is embedded into the I/O stream through
Manchester encoding. The bus is controlled by a
master device which determines the clock period, con-
trols the bus access and initiates all operations, while
the 11XX works as slave. Both master and slave can
operate as transmitter or receiver, but the master
device determines which mode is active.
FIGURE 2-1: BLOCK DIAGRAM
SCIO
STATUS
Register
I/O Control Memory
Control
Logic
X
Dec
HV Generator
EEPROM
Array
Page Latches
Y Decoder
Sense Amp.
R/W Control
Logic
Vcc
Vss
Current-
Limited
Slope
Control
2010 Microchip Technology Inc. Preliminary DS22067H-page 7
11AAXXX/11LCXXX
3.0 BUS CHARACTERISTICS
3.1 Standby Pulse
When the master has control of SCIO, a standby pulse
can be generated by holding SCIO high for TSTBY. At
this time, the 11XX will reset and return to Standby
mode. Subsequently, a high-to-low transition on SCIO
(the first low pulse of the header) will return the device
to the active state.
Once a command is terminated satisfactorily (i.e., via
a NoMAK/SAK combination during the Acknowledge
sequence), performing a standby pulse is not required
to begin a new command as long as the device to be
selected is the same device selected during the previ-
ous command. However, a period of TSS must be
observed after the end of the command and before the
beginning of the start header. After TSS, the start
header (including THDR low pulse) can be transmitted
in order to begin the new command.
If a command is terminated in any manner other than a
NoMAK/SAK combination, then the master must per-
form a standby pulse before beginning a new com-
mand, regardless of which device is to be selected.
An example of two consecutive commands is shown in
Figure 3-1. Note that the device address is the same
for both commands, indicating that the same device is
being selected both times.
A standby pulse cannot be generated while the slave
has control of SCIO. In this situation, the master must
wait for the slave to finish transmitting and to release
SCIO before the pulse can be generated.
If, at any point during a command, an error is detected
by the master, a standby pulse should be generated
and the command should be performed again.
FIGURE 3-1: CONSECUTIVE COMMANDS EXAMPLE
3.2 Start Data Transfer
All operations must be preceded by a start header. The
start header consists of holding SCIO low for a period
of THDR, followed by transmitting an 8-bit ‘01010101’
code. This code is used to synchronize the slave’s
internal clock period with the master’s clock period, so
accurate timing is very important.
When a standby pulse is not required (i.e., between
successive commands to the same device), a period of
T
SS must be observed after the end of the command
and before the beginning of the start header.
Figure 3-2 shows the waveform for the start header,
including the required Acknowledge sequence at the
end of the byte.
FIGURE 3-2: START HEADER
Note: After a POR/BOR event occurs, a low-
to-high transition on SCIO must be gen-
erated before proceeding with communi-
cation, including a standby pulse.
11010100
Start Header
SCIO
Device Address
MAK
00001010
MAK
NoSAK
SAK
Standby Pulse(1)
11010100
Start Header
SCIO
Device Address
MAK
00001010
MAK
NoSAK
SAK
NoMAK
SAK
TSS
Note 1: After a POR/BOR event, a low-to-high transition on SCIO is required to occur before the first
standby pulse.
SCIO
Data ‘0’Data ‘1’Data ‘0’Data ‘1’Data ‘0’Data ‘1’Data ‘0’Data ‘1’MAK NoSAKTSS THDR
11AAXXX/11LCXXX
DS22067H-page 8 Preliminary 2010 Microchip Technology Inc.
3.3 Acknowledge
An Acknowledge routine occurs after each byte is
transmitted, including the start header. This routine
consists of two bits. The first bit is transmitted by the
master, and the second bit is transmitted by the slave.
The Master Acknowledge, or MAK, is signified by trans-
mitting a ‘1’, and informs the slave that the current
operation is to be continued. Conversely, a Not
Acknowledge, or NoMAK, is signified by transmitting a
‘0’, and is used to end the current operation (and initiate
the write cycle for write operations).
The slave Acknowledge, or SAK, is also signified by
transmitting a ‘1’, and confirms proper communication.
However, unlike the NoMAK, the NoSAK is signified by
the lack of a middle edge during the bit period.
A NoSAK will occur for the following events:
• Following the start header
• Following the device address, if no slave on the
bus matches the transmitted address
• Following the command byte, if the command is
invalid, including Read, CRRD, Write, WRSR,
SETAL, and ERAL during a write cycle.
• If the slave becomes out of sync with the master
• If a command is terminated prematurely by using
a NoMAK, with the exception of immediately after
the device address.
See Figure 3.3 and Figure 3-4 for details.
If a NoSAK is received from the slave after any byte
(except the start header), an error has occurred. The
master should then perform a standby pulse and begin
the desired command again.
FIGURE 3-3: ACKNOWLEDGE
ROUTINE
FIGURE 3-4: ACKNOWLEDGE BITS
3.4 Device Addressing
A device address byte is the first byte received from the
master device following the start header. The device
address byte consists of a four-bit family code, for the
11XX this is set as ‘1010’. The last four bits of the
device address byte are the device code, which is
hardwired to ‘0000’ on the 11XXXX0 devices.
The device code on 11XXXX1 devices is hardwired to
‘0001’. This allows both 11XXXX0 and 11XXXX1
devices to be used on the same bus without address
conflicts.
FIGURE 3-5: DEVICE ADDRESS BYTE
ALLOCATION
3.5 Bus Conflict Protection
To help guard against high current conditions arising
from bus conflicts, the 11XX features a current-limited
output driver. The IOL and IOH specifications describe
the maximum current that can be sunk or sourced,
respectively, by the SCIO pin. The 11XX will vary the
output driver impedance to ensure that the maximum
current level is not exceeded.
Note: A MAK must always be transmitted
following the start header.
Note: When a NoMAK is used to end a WRITE
or WRSR instruction, the write cycle is
not initiated if no bytes of data have
been received.
Note: In order to guard against bus contention,
a NoSAK will occur after the start
header.
Master Slave
MAK SAK
MAK (‘1’)
NoMAK (‘0’)
SAK (‘1’)
NoSAK(1)
Note 1:
valid SAK.
A NoSAK is defined as any sequence that is not a
1010000
MAK
SLAVE ADDRESS
0(1)
SAK
Note 1: This bit is a ‘1’ on the 11XXXX1.
2010 Microchip Technology Inc. Preliminary DS22067H-page 9
11AAXXX/11LCXXX
3.6 Device Standby
The 11XX features a low-power Standby mode during
which the device is waiting to begin a new command.
A high-to-low transition on SCIO will exit low-power
mode and prepare the device for receiving the start
header.
Standby mode will be entered upon the following
conditions:
• A NoMAK followed by a SAK (i.e., valid termina-
tion of a command)
• Reception of a standby pulse
3.7 Device Idle
The 11XX features an Idle mode during which all serial
data is ignored until a standby pulse occurs. Idle mode
will be entered upon the following conditions:
• Invalid device address
• Invalid command byte, including Read, CRRD,
Write, WRSR, SETAL and ERAL during a write
cycle.
• Missed edge transition
• Reception of a MAK following a WREN, WRDI,
SETAL, or ERAL command byte
• Reception of a MAK following the data byte of a
WRSR command
An invalid start header will indirectly cause the device
to enter Idle mode. Whether or not the start header is
invalid cannot be detected by the slave, but will
prevent the slave from synchronizing properly with the
master. If the slave is not synchronized with the
master, an edge transition will be missed, thus causing
the device to enter Idle mode.
3.8 Synchronization
At the beginning of every command, the 11XX utilizes
the start header to determine the master’s bus clock
period. This period is then used as a reference for all
subsequent communication within that command.
The 11XX features re-synchronization circuitry which
will monitor the position of the middle data edge during
each MAK bit and subsequently adjust the internal time
reference in order to remain synchronized with the
master.
There are two variables which can cause the 11XX to
lose synchronization. The first is frequency drift,
defined as a change in the bit period, T
E. The second is
edge jitter, which is a single occurrence change in the
position of an edge within a bit period, while the bit
period itself remains constant.
3.8.1 FREQUENCY DRIFT
Within a system, there is a possibility that frequencies
can drift due to changes in voltage, temperature, etc.
The re-synchronization circuitry provides some toler-
ance for such frequency drift. The tolerance range is
specified by two parameters, FDRIFT and FDEV. FDRIFT
specifies the maximum tolerable change in bus fre-
quency per byte. FDEV specifies the overall limit in fre-
quency deviation within an operation (i.e., from the end
of the start header until communication is terminated
for that operation). The start header at the beginning of
the next operation will reset the re-synchronization cir-
cuitry and allow for another FDEV amount of frequency
drift.
3.8.2 EDGE JITTER
Ensuring that edge transitions from the master always
occur exactly in the middle or end of the bit period is not
always possible. Therefore, the re-synchronization cir-
cuitry is designed to provide some tolerance for edge
jitter.
The 11XX adjusts its phase every MAK bit, so TIJIT
specifies the maximum allowable peak-to-peak jitter
relative to the previous MAK bit. Since the position of
the previous MAK bit would be difficult to measure by
the master, the minimum and maximum jitter values for
a system should be considered the worst-case. These
values will be based on the execution time for different
branch paths in software, jitter due to thermal noise,
etc.
The difference between the minimum and maximum
values, as a percentage of the bit period, should be cal-
culated and then compared against TIJIT to determine
jitter compliance.
Note: In the case of the WRITE, WRSR, SETAL, or
ERAL commands, the write cycle is initiated
upon receipt of the NoMAK, assuming all
other write requirements have been met.
Note: Because the 11XX only re-synchronizes
during the MAK bit, the overall ability to
remain synchronized depends on a combi-
nation of frequency drift and edge jitter (i.e.,
if the MAK bit edge is experiencing the max-
imum allowable edge jitter, then there is no
room for frequency drift). Conversely, if the
frequency has drifted to the maximum
amount tolerable within a byte, then no edge
jitter can be present.
11AAXXX/11LCXXX
DS22067H-page 10 Preliminary 2010 Microchip Technology Inc.
4.0 DEVICE COMMANDS
After the device address byte, a command byte must
be sent by the master to indicate the type of operation
to be performed. The code for each instruction is listed
in Table 4-1.
TABLE 4-1: INSTRUCTION SET
4.1 Read Instruction
The Read command allows the master to access any
memory location in a random manner. After the READ
instruction has been sent to the slave, the two bytes of
the Word Address are transmitted, with an Acknowl-
edge sequence being performed after each byte. Then,
the slave sends the first data byte to the master. If more
data is to be read, the master sends a MAK, indicating
that the slave should output the next data byte. This
continues until the master sends a NoMAK, which ends
the operation.
To provide sequential reads in this manner, the 11XX
contains an internal Address Pointer which is incre-
mented by one after the transmission of each byte. This
Address Pointer allows the entire memory contents to
be serially read during one operation. When the highest
address is reached, the Address Pointer rolls over to
address ‘0x000’ if the master chooses to continue the
operation by providing a MAK.
FIGURE 4-1: READ COMMAND SEQUENCE
Instruction Name Instruction Code Hex Code Description
READ 0000 0011 0x03 Read data from memory array beginning at specified address
CRRD 0000 0110 0x06 Read data from current location in memory array
WRITE 0110 1100 0x6C Write data to memory array beginning at specified address
WREN 1001 0110 0x96 Set the write enable latch (enable write operations)
WRDI 1001 0001 0x91 Reset the write enable latch (disable write operations)
RDSR 0000 0101 0x05 Read STATUS register
WRSR 0110 1110 0x6E Write STATUS register
ERAL 0110 1101 0x6D Write ‘0x00’ to entire array
SETAL 0110 0111 0x67 Write ‘0xFF’ to entire array
7654
Data Byte 1
32107654
Data Byte 2
32107654
Data Byte n
3210
SCIO
MAK
MAK
NoMAK
11010100
Start Header
SCIO
Device Address
MAK
00
(1)
001010
MAK
Command
01000001
MAK
NoSAK
SAK
Standby Pulse
SCIO
SAK
15 14 13 12
Word Address MSB
11 10 9 8
MAK
SAK
7654
Word Address LSB
3210
MAK
SAK
SAK
SAK
SAK
Note 1: For the 11XXXX1, this bit must be a ‘1’.
2010 Microchip Technology Inc. Preliminary DS22067H-page 11
11AAXXX/11LCXXX
4.2 Current Address Read (CRRD)
Instruction
The internal address counter featured on the 11XX
maintains the address of the last memory array loca-
tion accessed. The CRRD instruction allows the mas-
ter to read data back beginning from this current
location. Consequently, no word address is provided
upon issuing this command.
Note that, except for the initial word address, the
READ and CRRD instructions are identical, including
the ability to continue requesting data through the use
of MAKs in order to sequentially read from the array.
As with the READ instruction, the CRRD instruction is
terminated by transmitting a NoMAK.
Table 4-2 lists the events upon which the internal
address counter is modified.
TABLE 4-2: INTERNAL ADDRESS
COUNTER
FIGURE 4-2: CRRD COMMAND SEQUENCE
Command Event Action
— Power-on Reset Counter is undefined
READ or
WRITE
MAK edge fol-
lowing each
Address byte
Counter is updated
with newly received
value
READ,
WRITE, or
CRRD
MAK/NoMAK
edge following
each data byte
Counter is incre-
mented by 1
Note: If, following each data byte in a READ,
WRITE, or CRRD instruction, neither a
MAK nor a NoMAK edge is received
(i.e., if a standby pulse occurs instead),
the internal address counter will not be
incremented.
Note: During a Write command, once the last
data byte for a page has been loaded,
the internal Address Pointer will rollover
to the beginning of the selected page.
7654
Data Byte 1
32107654
Data Byte 2
3210
7654
Data Byte n
3210
SCIO
MAK
MAK
NoMAK
11010100
Start Header
SCIO
Device Address
MAK
00
(1)
001010
MAK
Command
10000001
MAK
NoSAK
SAK
Standby Pulse
SCIO
SAK
SAK
SAK
SAK
Note 1: For the 11XXXX1, this bit must be a ‘1’.
11AAXXX/11LCXXX
DS22067H-page 12 Preliminary 2010 Microchip Technology Inc.
4.3 Write Instruction
Prior to any attempt to write data to the 11XX, the write
enable latch must be set by issuing the WREN
instruction (see Section 4.4).
Once the write enable latch is set, the user may pro-
ceed with issuing a WRITE instruction (including the
header and device address bytes) followed by the MSB
and LSB of the Word Address. Once the last Acknowl-
edge sequence has been performed, the master
transmits the data byte to be written.
The 11XX features a 16-byte page buffer, meaning that
up to 16 bytes can be written at one time. To utilize this
feature, the master can transmit up to 16 data bytes to
the 11XX, which are temporarily stored in the page buf-
fer. After each data byte, the master sends a MAK, indi-
cating whether or not another data byte is to follow. A
NoMAK indicates that no more data is to follow, and as
such will initiate the internal write cycle.
Upon receipt of each word, the four lower-order
Address Pointer bits are internally incremented by one.
The higher-order bits of the word address remain con-
stant. If the master should transmit data past the end of
the page, the address counter will roll over to the begin-
ning of the page, where further received data will be
written.
FIGURE 4-3: WRITE COMMAND SEQUENCE
Note: If a NoMAK is generated before any data
has been provided, or if a standby pulse
occurs before the NoMAK is generated,
the 11XX will be reset, and the write
cycle will not be initiated.
Note: Page write operations are limited to writ-
ing bytes within a single physical page,
regardless of the number of bytes actu-
ally being written. Physical page bound-
aries start at addresses that are integer
multiples of the page size (16 bytes) and
end at addresses that are integer multi-
ples of the page size minus 1. As an
example, the page that begins at
address 0x30 ends at address 0x3F. If a
page Write command attempts to write
across a physical page boundary, the
result is that the data wraps around to
the beginning of the current page (over-
writing data previously stored there),
instead of being written to the next page
as might be expected. It is therefore
necessary for the application software to
prevent page write operations that
would attempt to cross a page bound-
ary.
7654
Data Byte 1
32107654
Data Byte 2
32107654
Data Byte n
3210
SCIO
MAK
MAK
No MAK
11010100
Start Header
SCIO
Device Address
MAK
00
(1)
001010
MAK
Command
10101100
MAK
NoSAK
SAK
Standby Pulse
SCIO
SAK
15 14 13 12
Word Address MSB
11 10 9 8
MAK
SAK
7654
Word Address LSB
3210
MAK
SAK
SAK
SAK
SAK
Twc
Note 1: For the 11XXXX1, this bit must be a ‘1’.
2010 Microchip Technology Inc. Preliminary DS22067H-page 13
11AAXXX/11LCXXX
4.4 Write Enable (WREN) and Write
Disable (WRDI) Instructions
The 11XX contains a write enable latch. See Table 6-1
for the Write-Protect Functionality Matrix. This latch
must be set before any write operation will be com-
pleted internally. The WREN instruction will set the
latch, and the WRDI instruction will reset the latch.
The following is a list of conditions under which the
write enable latch will be reset:
• Power-up
•WRDI instruction successfully executed
•WRSR instruction successfully executed
•WRITE instruction successfully executed
•ERAL instruction successfully executed
•SETAL instruction successfully executed
FIGURE 4-4: WRITE ENABLE COMMAND SEQUENCE
FIGURE 4-5: WRITE DISABLE COMMAND SEQUENCE
Note: The WREN and WRDI instructions must
be terminated with a NoMAK following
the command byte. If a NoMAK is not
received at this point, the command will
be considered invalid, and the device
will go into Idle mode without responding
with a SAK or executing the command.
11010100
Start Header
SCIO
Device Address
MAK
00
(1)
001010
MAK
Command
10010011
NoMAK
NoSAK
SAK
Standby Pulse
SCIO
SAK
Note 1: For the 11XXXX1, this bit must be a ‘1’.
11010100
Start Header
SCIO
Device Address
MAK
00
(1)
001010
MAK
Command
01010010
NoMAK
NoSAK
SAK
Standby Pulse
SCIO
SAK
Note 1: For the 11XXXX1, this bit must be a ‘1’.
11AAXXX/11LCXXX
DS22067H-page 14 Preliminary 2010 Microchip Technology Inc.
4.5 Read Status Register (RDSR)
Instruction
The RDSR instruction provides access to the STATUS
register. The STATUS register may be read at any time,
even during a write cycle. The STATUS register is
formatted as follows:
The Write-In-Process (WIP) bit indicates whether the
11XX is busy with a write operation. When set to a ‘1’,
a write is in progress, when set to a ‘0’, no write is in
progress. This bit is read-only.
The Write Enable Latch (WEL) bit indicates the status
of the write enable latch. When set to a ‘1’, the latch
allows writes to the array, when set to a ‘0’, the latch
prohibits writes to the array. This bit is set and cleared
using the WREN and WRDI instructions, respectively.
This bit is read-only for any other instruction.
The Block Protection (BP0 and BP1) bits indicate
which blocks are currently write-protected. These bits
are set by the user through the WRSR instruction.
These bits are nonvolatile.
The WIP and WEL bits will update dynamically (asyn-
chronous to issuing the RDSR instruction). Further-
more, after the STATUS register data is received, the
master can provide a MAK during the Acknowledge
sequence to request that the data be transmitted again.
This allows the master to continuously monitor the WIP
and WEL bits without the need to issue another full
command.
Once the master is finished, it provides a NoMAK to
end the operation.
FIGURE 4-6: READ STATUS REGISTER COMMAND SEQUENCE
7654 3 2 1 0
XXXX BP1 BP0 WEL WIP
Note: Bits 4-7 are don’t cares, and will read as ‘0’.
Note: If Read Status Register command is
initiated while the 11XX is currently
executing an internal write cycle on the
STATUS register, the new Block
Protection bit values will be read during
the entire command.
Note: The current drawn for a Read Status
Register command during a write cycle
is a combination of the ICC Read and ICC
Write operating currents.
11010100
Start Header
SCIO
Device Address
MAK
00
(1)
001010
MAK
Command
11000000
MAK
NoSAK
SAK
Standby Pulse
SCIO
SAK
STATUS Register Data
3210
NoMAK
SAK
The STATUS register data can continuously be read, or polled, by transmitting a MAK in place of the NoMAK.Note 2:
0000
Note 1: For the 11XXXX1, this bit must be a ‘1’.
2010 Microchip Technology Inc. Preliminary DS22067H-page 15
11AAXXX/11LCXXX
4.6 Write Status Register (WRSR)
Instruction
The WRSR instruction allows the user to select one of
four levels of protection for the array by writing to the
appropriate bits in the STATUS register. The array is
divided up into four segments. The user has the ability
to write-protect none, one, two, or all four of the seg-
ments of the array. The partitioning is controlled as
illustrated in Table 4-3.
After transmitting the STATUS register data, the master
must transmit a NoMAK during the Acknowledge
sequence in order to initiate the internal write cycle.
TABLE 4-3: ARRAY PROTECTION
TABLE 4-4: PROTECTED ARRAY ADDRESS LOCATIONS
FIGURE 4-7: WRITE STATUS REGISTER COMMAND SEQUENCE
Note: The WRSR instruction must be termi-
nated with a NoMAK following the data
byte. If a NoMAK is not received at this
point, the command will be considered
invalid, and the device will go into Idle
mode without responding with a SAK or
executing the command.
BP1 BP0 Address Ranges Write-Protected Address Ranges Unprotected
00 None All
01 Upper 1/4 Lower 3/4
10 Upper 1/2 Lower 1/2
11 All None
Density Upper 1/4 Upper 1/2 All Sectors
1K 60h-7Fh 40h-7Fh 00h-7Fh
2K C0h-FFh 80h-FFh 00h-FFh
4K 180h-1FFh 100h-1FFh 000h-1FFh
8K 300h-3FFh 200h-3FFh 000h-3FFh
16K 600h-7FFh 400h-7FFh 000h-7FFh
11010100
Start Header
SCIO
Device Address
MAK
00
(1)
001010
MAK
Command
10101101
MAK
NoSAK
SAK
Standby Pulse
SCIO
SAK
7654
Status Register Data
3210
NoMAK
SAK
Twc
Note 1: For the 11XXXX1, this bit must be a ‘1’.
11AAXXX/11LCXXX
DS22067H-page 16 Preliminary 2010 Microchip Technology Inc.
4.7 Erase All (ERAL) Instruction
The ERAL instruction allows the user to write ‘0x00’ to
the entire memory array with one command. Note that
the write enable latch (WEL) must first be set by issuing
the WREN instruction.
Once the write enable latch is set, the user may pro-
ceed with issuing a ERAL instruction (including the
header and device address bytes). Immediately after
the NoMAK bit has been transmitted by the master, the
internal write cycle is initiated, during which time all
words of the memory array are written to ‘0x00’.
The ERAL instruction is ignored if either of the Block
Protect bits (BP0, BP1) are not 0, meaning 1/4, 1/2, or
all of the array is protected.
FIGURE 4-8: ERASE ALL COMMAND SEQUENCE
4.8 Set All (SETAL) Instruction
The SETAL instruction allows the user to write ‘0xFF’
to the entire memory array with one command. Note
that the write enable latch (WEL) must first be set by
issuing the WREN instruction.
Once the write enable latch is set, the user may pro-
ceed with issuing a SETAL instruction (including the
header and device address bytes). Immediately after
the NoMAK bit has been transmitted by the master, the
internal write cycle is initiated, during which time all
words of the memory array are written to ‘0xFF’.
The SETAL instruction is ignored if either of the Block
Protect bits (BP0, BP1) are not 0, meaning 1/4, 1/2, or
all of the array is protected.
FIGURE 4-9: SET ALL COMMAND SEQUENCE
Note: The ERAL instruction must be termi-
nated with a NoMAK following the com-
mand byte. If a NoMAK is not received at
this point, the command will be consid-
ered invalid, and the device will go into
Idle mode without responding with a
SAK or executing the command.
11010100
Start Header
SCIO
Device Address
MAK
00
(1)
001010
MAK
Command
11101100
NoMAK
NoSAK
SAK
Standby Pulse
SCIO
SAK
Twc
Note 1: For the 11XXXX1, this bit must be a ‘1’.
Note: The SETAL instruction must be termi-
nated with a NoMAK following the com-
mand byte. If a NoMAK is not received at
this point, the command will be consid-
ered invalid, and the device will go into
Idle mode without responding with a
SAK or executing the command.
11010100
Start Header
SCIO
Device Address
MAK
00
(1)
001010
MAK
Command
11001101
NoMAK
NoSAK
SAK
Standby Pulse
SCIO
SAK
Twc
Note 1: For the 11XXXX1, this bit must be a ‘1’.
2010 Microchip Technology Inc. Preliminary DS22067H-page 17
11AAXXX/11LCXXX
5.0 DATA PROTECTION
The following protection has been implemented to
prevent inadvertent writes to the array:
• The Write Enable Latch (WEL) is reset on power-
up
•A Write Enable (
WREN) instruction must be issued
to set the write enable latch
• After a write, ERAL, SETAL, or WRSR command,
the write enable latch is reset
• Commands to access the array or write to the
status register are ignored during an internal write
cycle and programming is not affected
6.0 POWER-ON STATE
The 11XX powers on in the following state:
• The device is in low-power Shutdown mode,
requiring a low-to-high transition on SCIO to enter
Idle mode
• The Write Enable Latch (WEL) is reset
• The internal Address Pointer is undefined
• A low-to-high transition, standby pulse and subse-
quent high-to-low transition on SCIO (the first low
pulse of the header) are required to enter the
active state
.
TABLE 6-1: WRITE PROTECT FUNCTIONALITY MATRIX
WEL Protected Blocks Unprotected Blocks Status Register
0Protected Protected Protected
1Protected Writable Writable
11AAXXX/11LCXXX
DS22067H-page 18 Preliminary 2010 Microchip Technology Inc.
7.0 PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 7-1.
TABLE 7-1: PIN FUNCTION TABLE
7.1 Serial Clock, Data Input/Output
(SCIO)
SCIO is a bidirectional pin used to transfer commands
and addresses into, as well as data into and out of, the
device. The serial clock is embedded into the data
stream through Manchester encoding. Each bit is
represented by a signal transition at the middle of the
bit period.
Name 3-pin SOT-23 3-pin TO-92 4-pin CS 8-pin PDIP/SOIC/
MSOP/TDFN Description
SCIO 1 2 3 5 Serial Clock, Data Input/Output
VCC 2 3 1 8 Supply Voltage
VSS 3 1 2 4 Ground
NC — — 4 1,2,3,6,7 No Internal Connection
2010 Microchip Technology Inc. Preliminary DS22067H-page 19
11AAXXX/11LCXXX
8.0 PACKAGING INFORMATION
8.1 Package Marking Information
T/XXXNNN
XXXXXXXX
YYWW
8-Lead PDIP
I/P 1L7
11AA160
0828
Example:
3
e
8-Lead PDIP Package Marking (Pb-Free)
Device Line 1 Marking Device Line 1 Marking
11AA010 11AA010 11LC010 11LC010
11AA020 11AA020 11LC020 11LC020
11AA040 11AA040 11LC040 11LC040
11AA080 11AA080 11LC080 11LC080
11AA160 11AA160 11LC160 11LC160
11AA161 11AA161 11LC161 11LC161
Note: T = Temperature Grade (I, E)
Legend: XX...X Customer-specific information
Y Year code (last digit of calendar year)
YY Year code (last 2 digits of calendar year)
WW Week code (week of January 1 is week ‘01’)
NNN Alphanumeric traceability code
Pb-free JEDEC designator for Matte Tin (Sn)
*This package is Pb-free. The Pb-free JEDEC designator ( )
can be found on the outer packaging for this package.
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
3
e
3
e
11AAXXX/11LCXXX
DS22067H-page 20 Preliminary 2010 Microchip Technology Inc.
8-Lead SOIC
XXXXYYWW
XXXXXXXT
NNN
Example:
SN 0828
11AA160I
1L7
3
e
8-Lead SOIC Package Marking (Pb-Free)
Device Line 1 Marking Device Line 1 Marking
11AA010 11AA010T 11LC010 11LC010T
11AA020 11AA020T 11LC020 11LC020T
11AA040 11AA040T 11LC040 11LC040T
11AA080 11AA080T 11LC080 11LC080T
11AA160 11AA160T 11LC160 11LC160T
11AA161 11AA161T 11LC161 11LC161T
Note: T = Temperature Grade (I, E)
Legend: XX...X Customer-specific information
Y Year code (last digit of calendar year)
YY Year code (last 2 digits of calendar year)
WW Week code (week of January 1 is week ‘01’)
NNN Alphanumeric traceability code
Pb-free JEDEC designator for Matte Tin (Sn)
*This package is Pb-free. The Pb-free JEDEC designator ( )
can be found on the outer packaging for this package.
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
3
e
3
e
2010 Microchip Technology Inc. Preliminary DS22067H-page 21
11AAXXX/11LCXXX
3
e
8-Lead MSOP (150 mil) Example:
XXXXXXT
YWWNNN
11A01I
8281L7
8-Lead MSOP Package Marking (Pb-Free)
Device Line 1 Marking Device Line 1 Marking
11AA010 11A01T 11LC010 11L01T
11AA020 11A02T 11LC020 11L02T
11AA040 11A04T 11LC040 11L04T
11AA080 11A08T 11LC080 11L08T
11AA160 11AAT 11LC160 11LAT
11AA161 11AA1T 11LC161 11LA1T
Note: T = Temperature Grade (I, E)
Legend: XX...X Customer-specific information
Y Year code (last digit of calendar year)
YY Year code (last 2 digits of calendar year)
WW Week code (week of January 1 is week ‘01’)
NNN Alphanumeric traceability code
Pb-free JEDEC designator for Matte Tin (Sn)
*This package is Pb-free. The Pb-free JEDEC designator ( )
can be found on the outer packaging for this package.
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
3
e
3
e
11AAXXX/11LCXXX
DS22067H-page 22 Preliminary 2010 Microchip Technology Inc.
8-Lead 2x3 TDFN Example:
XXX
YWW
NN
D51
828
17
8-Lead 2x3 TDFN Package Marking (Pb-Free)
Device I-Temp Marking Device I-Temp Marking E-Temp Marking
11AA010 D11 11LC010 D14 D15
11AA020 D21 11LC020 D24 D25
11AA040 D31 11LC040 D34 D35
11AA080 D41 11LC080 D44 D45
11AA160 D51 11LC160 D54 D55
11AA161 D5D 11LC161 D5G D5H
Legend: XX...X Customer-specific information
Y Year code (last digit of calendar year)
YY Year code (last 2 digits of calendar year)
WW Week code (week of January 1 is week ‘01’)
NN Alphanumeric traceability code
Pb-free JEDEC designator for Matte Tin (Sn)
*This package is Pb-free. The Pb-free JEDEC designator ( )
can be found on the outer packaging for this package.
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
3
e
3
e
2010 Microchip Technology Inc. Preliminary DS22067H-page 23
11AAXXX/11LCXXX
3-Lead SOT-23
XXNN
Example:
B517
3-Lead SOT-23 Package Marking (Pb-Free)
Device I-Temp Marking Device I-Temp Marking E-Temp Marking
11AA010 B1NN 11LC010 M1NN N1NN
11AA020 B2NN 11LC020 M2NN N2NN
11AA040 B3NN 11LC040 M3NN N3NN
11AA080 B4NN 11LC080 M4NN N4NN
11AA160 B5NN 11LC160 M5NN N5NN
11AA161 B0NN 11LC161 M0NN N0NN
Legend: XX...X Customer-specific information
Y Year code (last digit of calendar year)
YY Year code (last 2 digits of calendar year)
WW Week code (week of January 1 is week ‘01’)
NNN Alphanumeric traceability code
Pb-free JEDEC designator for Matte Tin (Sn)
*This package is Pb-free. The Pb-free JEDEC designator ( )
can be found on the outer packaging for this package.
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
3
e
3
e
11AAXXX/11LCXXX
DS22067H-page 24 Preliminary 2010 Microchip Technology Inc.
3-Lead TO-92 Package Marking (Pb-Free)
Device Line 1 Marking Device Line 1 Marking
11AA010 11A010 11LC010 11L010
11AA020 11A020 11LC020 11L020
11AA040 11A040 11LC040 11L040
11AA080 11A080 11LC080 11L080
11AA160 11A160 11LC160 11L160
11AA161 11A161 11LC161 11L161
Note: T = Temperature Grade (I, E)
3-Lead TO-92
T/XXXX
XXXXXX
Example:
3
e
YWW
NNN
I/TO
11A160
928
1L7
3
e
Legend: XX...X Customer-specific information
Y Year code (last digit of calendar year)
YY Year code (last 2 digits of calendar year)
WW Week code (week of January 1 is week ‘01’)
NNN Alphanumeric traceability code
Pb-free JEDEC designator for Matte Tin (Sn)
*This package is Pb-free. The Pb-free JEDEC designator ( )
can be found on the outer packaging for this package.
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
3
e
3
e
2010 Microchip Technology Inc. Preliminary DS22067H-page 25
11AAXXX/11LCXXX
4-Lead Chip Scale Package Marking (Pb-Free)
Device Line 1 Marking
11AA010 AW
11AA020 BW
11AA040 CW
11AA080 DW
11AA160 EW
11AA161 HW
4-Lead Chip Scale
NN
XW
Example:
17
E3
Legend: XX...X Customer-specific information
Y Year code (last digit of calendar year)
YY Year code (last 2 digits of calendar year)
WW Week code (week of January 1 is week ‘01’)
NNN Alphanumeric traceability code
Pb-free JEDEC designator for Matte Tin (Sn)
*This package is Pb-free. The Pb-free JEDEC designator ( )
can be found on the outer packaging for this package.
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
3
e
3
e
11AAXXX/11LCXXX
DS22067H-page 26 Preliminary 2010 Microchip Technology Inc.
/HDG3ODVWLF'XDO,Q/LQH3±PLO%RG\>3',3@
1RWHV
3LQYLVXDOLQGH[IHDWXUHPD\YDU\EXWPXVWEHORFDWHGZLWKWKHKDWFKHGDUHD
6LJQLILFDQW&KDUDFWHULVWLF
'LPHQVLRQV'DQG(GRQRWLQFOXGHPROGIODVKRUSURWUXVLRQV0ROGIODVKRUSURWUXVLRQVVKDOOQRWH[FHHGSHUVLGH
'LPHQVLRQLQJDQGWROHUDQFLQJSHU$60(<0
%6&%DVLF'LPHQVLRQ7KHRUHWLFDOO\H[DFWYDOXHVKRZQZLWKRXWWROHUDQFHV
1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
8QLWV ,1&+(6
'LPHQVLRQ/LPLWV 0,1 120 0$;
1XPEHURI3LQV 1
3LWFK H %6&
7RSWR6HDWLQJ3ODQH $ ± ±
0ROGHG3DFNDJH7KLFNQHVV $
%DVHWR6HDWLQJ3ODQH $ ± ±
6KRXOGHUWR6KRXOGHU:LGWK (
0ROGHG3DFNDJH:LGWK (
2YHUDOO/HQJWK '
7LSWR6HDWLQJ3ODQH /
/HDG7KLFNQHVV F
8SSHU/HDG:LGWK E
/RZHU/HDG:LGWK E
2YHUDOO5RZ6SDFLQJ H% ± ±
N
E1
NOTE 1
D
123
A
A1
A2
L
b1
b
e
E
eB
c
0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &%
2010 Microchip Technology Inc. Preliminary DS22067H-page 27
11AAXXX/11LCXXX
/HDG3ODVWLF6PDOO2XWOLQH61±1DUURZPP%RG\>62,&@
1RWHV
3LQYLVXDOLQGH[IHDWXUHPD\YDU\EXWPXVWEHORFDWHGZLWKLQWKHKDWFKHGDUHD
6LJQLILFDQW&KDUDFWHULVWLF
'LPHQVLRQV'DQG(GRQRWLQFOXGHPROGIODVKRUSURWUXVLRQV0ROGIODVKRUSURWUXVLRQVVKDOOQRWH[FHHGPPSHUVLGH
'LPHQVLRQLQJDQGWROHUDQFLQJSHU$60(<0
%6& %DVLF'LPHQVLRQ7KHRUHWLFDOO\H[DFWYDOXHVKRZQZLWKRXWWROHUDQFHV
5() 5HIHUHQFH'LPHQVLRQXVXDOO\ZLWKRXWWROHUDQFHIRULQIRUPDWLRQSXUSRVHVRQO\
1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
8QLWV 0,//,0(7(56
'LPHQVLRQ/LPLWV 0,1 120 0$;
1XPEHURI3LQV 1
3LWFK H %6&
2YHUDOO+HLJKW $ ± ±
0ROGHG3DFNDJH7KLFNQHVV $ ± ±
6WDQGRII$ ±
2YHUDOO:LGWK ( %6&
0ROGHG3DFNDJH:LGWK ( %6&
2YHUDOO/HQJWK ' %6&
&KDPIHURSWLRQDO K ±
)RRW/HQJWK / ±
)RRWSULQW / 5()
)RRW$QJOH ±
/HDG7KLFNQHVV F ±
/HDG:LGWK E ±
0ROG'UDIW$QJOH7RS ±
0ROG'UDIW$QJOH%RWWRP ±
D
N
e
E
E1
NOTE 1
12 3
b
A
A1
A2
L
L1
c
h
h
φ
β
α
0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &%
11AAXXX/11LCXXX
DS22067H-page 28 Preliminary 2010 Microchip Technology Inc.
/HDG3ODVWLF6PDOO2XWOLQH61±1DUURZPP%RG\>62,&@
1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
2010 Microchip Technology Inc. Preliminary DS22067H-page 29
11AAXXX/11LCXXX
/HDG3ODVWLF0LFUR6PDOO2XWOLQH3DFNDJH06>0623@
1RWHV
3LQYLVXDOLQGH[IHDWXUHPD\YDU\EXWPXVWEHORFDWHGZLWKLQWKHKDWFKHGDUHD
'LPHQVLRQV'DQG(GRQRWLQFOXGHPROGIODVKRUSURWUXVLRQV0ROGIODVKRUSURWUXVLRQVVKDOOQRWH[FHHGPPSHUVLGH
'LPHQVLRQLQJDQGWROHUDQFLQJSHU$60(<0
%6& %DVLF'LPHQVLRQ7KHRUHWLFDOO\H[DFWYDOXHVKRZQZLWKRXWWROHUDQFHV
5() 5HIHUHQFH'LPHQVLRQXVXDOO\ZLWKRXWWROHUDQFHIRULQIRUPDWLRQSXUSRVHVRQO\
1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
8QLWV 0,//,0(7(56
'LPHQVLRQ/LPLWV 0,1 120 0$;
1XPEHURI3LQV 1
3LWFK H %6&
2YHUDOO+HLJKW $ ± ±
0ROGHG3DFNDJH7KLFNQHVV $
6WDQGRII $ ±
2YHUDOO:LGWK ( %6&
0ROGHG3DFNDJH:LGWK ( %6&
2YHUDOO/HQJWK ' %6&
)RRW/HQJWK /
)RRWSULQW / 5()
)RRW$QJOH ±
/HDG7KLFNQHVV F ±
/HDG:LGWK E ±
D
N
E
E1
NOTE 1
12
e
b
A
A1
A2 c
L1 L
φ
0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &%
11AAXXX/11LCXXX
DS22067H-page 30 Preliminary 2010 Microchip Technology Inc.
/HDG3ODVWLF'XDO)ODW1R/HDG3DFNDJH01±[[PP%RG\>7')1@
1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
2010 Microchip Technology Inc. Preliminary DS22067H-page 31
11AAXXX/11LCXXX
/HDG3ODVWLF'XDO)ODW1R/HDG3DFNDJH01±[[PP%RG\>7')1@
1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
11AAXXX/11LCXXX
DS22067H-page 32 Preliminary 2010 Microchip Technology Inc.
/HDG3ODVWLF7UDQVLVWRU2XWOLQH72>72@
1RWHV
'LPHQVLRQV$DQG(GRQRWLQFOXGHPROGIODVKRUSURWUXVLRQV0ROGIODVKRUSURWUXVLRQVVKDOOQRWH[FHHGSHUVLGH
'LPHQVLRQLQJDQGWROHUDQFLQJSHU$60(<0
%6& %DVLF'LPHQVLRQ7KHRUHWLFDOO\H[DFWYDOXHVKRZQZLWKRXWWROHUDQFHV
1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
8QLWV ,1&+(6
'LPHQVLRQ/LPLWV 0,1 0$;
1XPEHURI3LQV 1
3LWFK H %6&
%RWWRPWR3DFNDJH)ODW '
2YHUDOO:LGWK (
2YHUDOO/HQJWK $
0ROGHG3DFNDJH5DGLXV 5
7LSWR6HDWLQJ3ODQH / ±
/HDG7KLFNQHVV F
/HDG:LGWK E
E
A
N
1
L
b
e
c
R
D
123
0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &%
2010 Microchip Technology Inc. Preliminary DS22067H-page 33
11AAXXX/11LCXXX
/HDG3ODVWLF6PDOO2XWOLQH7UDQVLVWRU77>627@
1RWHV
'LPHQVLRQV'DQG(GRQRWLQFOXGHPROGIODVKRUSURWUXVLRQV0ROGIODVKRUSURWUXVLRQVVKDOOQRWH[FHHGPPSHUVLGH
'LPHQVLRQLQJDQGWROHUDQFLQJSHU$60(<0
%6& %DVLF'LPHQVLRQ7KHRUHWLFDOO\H[DFWYDOXHVKRZQZLWKRXWWROHUDQFHV
1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
8QLWV 0,//,0(7(56
'LPHQVLRQ/LPLWV 0,1 120 0$;
1XPEHURI3LQV 1
/HDG3LWFK H %6&
2XWVLGH/HDG3LWFK H %6&
2YHUDOO+HLJKW $ ±
0ROGHG3DFNDJH7KLFNQHVV $
6WDQGRII $ ±
2YHUDOO:LGWK ( ±
0ROGHG3DFNDJH:LGWK (
2YHUDOO/HQJWK '
)RRW/HQJWK /
)RRW$QJOH ±
/HDG7KLFNQHVV F ±
/HDG:LGWK E ±
b
N
E
E1
2
1
e
e1
D
A
A1
A2
c
L
φ
0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &%
11AAXXX/11LCXXX
DS22067H-page 34 Preliminary 2010 Microchip Technology Inc.
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2010 Microchip Technology Inc. Preliminary DS22067H-page 35
11AAXXX/11LCXXX
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
11AAXXX/11LCXXX
DS22067H-page 36 Preliminary 2010 Microchip Technology Inc.
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2010 Microchip Technology Inc. Preliminary DS22067H-page 37
11AAXXX/11LCXXX
APPENDIX A: REVISION HISTORY
Revision A (10/07)
Original release of this document.
Revision B (01/08)
Revised SOT-23 Package Type; Revised DFN
package to TDFN; Section 3.3 (added new bullet item);
Section 4.5 note; Table 7-1.
Revision C (03/08)
Removed patent pending notice; Revised Tables 1-1
and 1-2; Section 3.3 (bullet 3) and 3.7 (bullet 2);
Product ID System.
Revision D (04/08)
Revised document status to Preliminary; General
updates.
Revision E (09/08)
Updated UNI/O trademark; Revised Table 1-2,
parameters 3 and 5; Updated package drawings.
Revision F (10/09)
Added 3-lead TO-92 Package.
Revision G (12/09)
Added 11AA161/11LC161 device.
Revision H (03/10)
Added 4-lead Chip Scale package.
11AAXXX/11LCXXX
DS22067H-page 38 Preliminary 2010 Microchip Technology Inc.
NOTES:
2010 Microchip Technology Inc. Preliminary DS22067H-page 39
11AAXXX/11LCXXX
THE MICROCHIP WEB SITE
Microchip provides online support via our WWW site at
www.microchip.com. This web site is used as a means
to make files and information easily available to
customers. Accessible by using your favorite Internet
browser, the web site contains the following
information:
•Product Support – Data sheets and errata,
application notes and sample programs, design
resources, user’s guides and hardware support
documents, latest software releases and archived
software
•General Technical Support – Frequently Asked
Questions (FAQ), technical support requests,
online discussion groups, Microchip consultant
program member listing
•Business of Microchip – Product selector and
ordering guides, latest Microchip press releases,
listing of seminars and events, listings of
Microchip sales offices, distributors and factory
representatives
CUSTOMER CHANGE NOTIFICATION
SERVICE
Microchip’s customer notification service helps keep
customers current on Microchip products. Subscribers
will receive e-mail notification whenever there are
changes, updates, revisions or errata related to a
specified product family or development tool of interest.
To register, access the Microchip web site at
www.microchip.com, click on Customer Change
Notification and follow the registration instructions.
CUSTOMER SUPPORT
Users of Microchip products can receive assistance
through several channels:
• Distributor or Representative
• Local Sales Office
• Field Application Engineer (FAE)
• Technical Support
• Development Systems Information Line
Customers should contact their distributor,
representative or field application engineer (FAE) for
support. Local sales offices are also available to help
customers. A listing of sales offices and locations is
included in the back of this document.
Technical support is available through the web site
at: http://support.microchip.com
11AAXXX/11LCXXX
DS22067H-page 40 Preliminary 2010 Microchip Technology Inc.
READER RESPONSE
It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip prod-
uct. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation
can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150.
Please list the following information, and use this outline to provide us with your comments about this document.
To: Technical Publications Manager
RE: Reader Response
Total Pages Sent ________
From: Name
Company
Address
City / State / ZIP / Country
Telephone: (_______) _________ - _________
Application (optional):
Would you like a reply? Y N
Device: Literature Number:
Questions:
FAX: (______) _________ - _________
DS22067H11AAXXX/11LCXXX
1. What are the best features of this document?
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this document easy to follow? If not, why?
4. What additions to the document do you think would enhance the structure and subject?
5. What deletions from the document could be made without affecting the overall usefulness?
6. Is there any incorrect or misleading information (what and where)?
7. How would you improve this document?
2010 Microchip Technology Inc. Preliminary DS22067H-page 41
11AAXXX/11LCXXX
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO. X X /XXX
PackageTemperatureTape & Reel
Device
Device: 11AA01 = 1 Kbit, 1.8V UNI/O Serial EEPROM
11LC01 = 1 Kbit, 2.5V UNI/O Serial EEPROM
11AA02 = 2 Kbit, 1.8V UNI/O Serial EEPROM
11LC02 = 2 Kbit, 2.5V UNI/O Serial EEPROM
11AA04 = 4 Kbit, 1.8V UNI/O Serial EEPROM
11LC04 = 4 Kbit, 2.5V UNI/O Serial EEPROM
11AA08 = 8 Kbit, 1.8V UNI/O Serial EEPROM
11LC08 = 8 Kbit, 2.5V UNI/O Serial EEPROM
11AA16 = 16 Kbit, 1.8V UNI/O Serial EEPROM
11LC16 = 16 Kbit, 2.5V UNI/O Serial EEPROM
Device Address: 0= Standard Address – 0xA0
1= Alternate Address – 0xA1 (11XX161 only)
Tape & Reel: T = Tape and Reel
Blank = Tube
Temperature
Range:
I= -40C to +85C (Industrial)
E= -40C to +125C (Extended)
Package: P = 8-lead Plastic DIP (300 mil body)
SN = 8-lead Plastic SOIC (3.90 mm body)
MS = 8-lead Plastic Micro Small Outline (MSOP)
MNY(1) = 8-lead 2x3 mm TDFN
TO = 3-lead Plastic TO-92
TT = 3-lead SOT-23 (Tape and Reel only)
CS16K(2)= Chip Scale (CS), 4-lead (I-temp, “AA”, Tape and
Reel only)
Examples:
a) 11AA010-I/P = 1 Kbit, 1.8V Serial EEPROM,
Industrial temp., Standard address, PDIP pack-
age
b) 11LC160T-E/TT = 16 Kbit, 2.5V Serial
EEPROM, Extended temp., Tape & Reel,
SOT-23 package
c) 11AA080-I/MS = 8 Kbit, 1.8V Serial EEPROM,
Industrial temp., Standard address, MSOP
package
d) 11LC020T-I/SN = 2 Kbit, 2.5V Serial EEPROM,
Industrial temp., Tape & Reel, Standard
Address, SOIC package
e) 11AA040T-I/MNY = 4 Kbit, 1.8V Serial
EEPROM, Industrial temp., Tape and Reel,
Standard Address, 2x3 mm TDFN package,
Nickel Palladium Gold finish
f) 11LC161-I/SN = 16 Kbit, 2.5V Serial EEPROM,
Industrial temp., Alternate address, SOIC pack-
age
g) 11AA020T-I/CS16K = 2 Kbit, 1.8V Serial
EEPROM, Industrial temp., Standard address,
Chip Scale package
Range
Note 1: “Y” indicates a Nickel Palladium Gold (NiPdAu) finish.
2: “16K” indicates 160K technology.
X
Device
Address
11AAXXX/11LCXXX
DS22067H-page 42 Preliminary 2010 Microchip Technology Inc.
NOTES:
2010 Microchip Technology Inc. Preliminary DS22067H-page 43
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART,
PIC32 logo, rfPIC and UNI/O are registered trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor,
MXDEV, MXLAB, SEEVAL and The Embedded Control
Solutions Company are registered trademarks of Microchip
Technology Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, CodeGuard,
dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,
ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial
Programming, ICSP, Mindi, MiWi, MPASM, MPLAB Certified
logo, MPLIB, MPLINK, mTouch, Octopus, Omniscient Code
Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit,
PICtail, REAL ICE, rfLAB, Select Mode, Total Endurance,
TSHARC, UniWinDriver, WiperLock and ZENA are
trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2010, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
ISBN:978-1-60932-042-3
Note the following details of the code protection feature on Microchip devices:
• Microchip products meet the specification contained in their particular Microchip Data Sheet.
• Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
• There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
• Microchip is willing to work with the customer who is concerned about the integrity of their code.
• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Microchip received ISO/TS-16949:2002 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
DS22067H-page 44 Preliminary 2010 Microchip Technology Inc.
AMERICAS
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://support.microchip.com
Web Address:
www.microchip.com
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
Kokomo
Kokomo, IN
Tel: 765-864-8360
Fax: 765-864-8387
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
ASIA/PACIFIC
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8528-2100
Fax: 86-10-8528-2104
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
ASIA/PACIFIC
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
Taiwan - Hsin Chu
Tel: 886-3-6578-300
Fax: 886-3-6578-370
Taiwan - Kaohsiung
Tel: 886-7-536-4818
Fax: 886-7-536-4803
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
EUROPE
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
WORLDWIDE SALES AND SERVICE
01/05/10