2SB315A Data Sheet 2SB315A-CM1200DC-34N SCALE Dual-Channel Plug-and-Play Driver Driver solution for 130mm x 140mm dual IGBT modules with electrical interface suitable for the following IGBT modules: * CM1200DC-34N * CM1200DB-34N Abstract The 2SB315A-CM1200DC-34N is a dual-channel driver with an electrical interface based on CONCEPT's dual SCALE driver 2SD315AI, a proven technology for reliable driving and safe operation of IGBTs. The driver is matched to the above mentioned 1700V modules from Mitsubishi. Its plugand-play capability makes it ready to operate immediately after mounting. The user needs invest no effort in designing or adjusting it to a specific application. For drivers adapted to other types of high-power and high-voltage IGBT modules, refer to www.IGBT-Driver.com/go/plug-and-play Product Highlights Plug-and-play solution Active clamping of V ce at turn-off IGBT short-circuit and overcurrent protection No electrolytic capacitors 20-pin flat cable interface Monitoring of power supply voltage Duty cycle 0... 100% Extremely reliable; long service life Shortens application development time IGBT-Driver.com Applications Inverters Motor drives UPS Power-factor correctors Wind-power converters Welding SMPS 2-level converters and many others Page 1 2SB315A Data Sheet 2SB315A-CM1200DC-34N Important: Please refer to the relevant manuals! This data sheet contains only product-specific data. A detailed description, must-read application notes and general data applicable to this driver family are found in: "Description and Application Manual for 2SB315A SCALE Plug-and-play IGBT Driver". See www.IGBT-Driver.com/go/2SB315A Dimensions Dimensions: 130 x 145 mm, 21 mm height (30 mm with connector X1 and flat cable). Mounting principle: Connected to IGBT module with screws. Absolute Maximum Ratings Parameter Remarks Supply voltage VDC Supply voltage VDD Logic input voltage Gate peak current Iout Average supply current IDC Output power per gate Switching frequency DC-link voltage Operating temperature Storage temperature VDC to GND (Note 1) VDD to GND To GND Note 6 Notes 2,3 Note 3 Note 3 Note 4 Note 3 Min Max Units 0 16 0 16 0 VDD -15 +15 500 3 8.5 1200 -40 +85 -40 +90 V V V A mA W kHz V C C All data refer to +25C and VDC = 15V unless otherwise specified Page 2 INTELLIGENT POWER ELECTRONICS 2SB315A Data Sheet 2SB315A-CM1200DC-34N Electrical Characteristics Power supply Remarks Nominal supply voltage VDC Supply current IDC Supply current IDC Efficiency Nominal supply voltage VDD Supply current IDD Supply current IDD To GND (Note 1) Without load At 8.5 kHz switching frequency Internal DC/DC converter To GND Without load At 8.5 kHz switching frequency Power supply monitoring Test conditions Turn-on threshold Vth Hysteresis on/off Note 5 Note 5 Short circuit protection Remarks V ce -monitoring threshold Response time Blocking time Betw. aux. terminals Logic inputs Test conditions Input voltage All inputs Timing characteristics Test conditions Turn-on delay tpd(on) Turn-off delay tpd(off) Output rise time tr(out) Output fall time tf(out) Dead time between outputs Note 9 Note 9 Outputs Turn-on gate resistor R g(on) Turn-off gate resistor R g(off) Output current SOx Output voltage rating SOx IGBT-Driver.com Min Typ. Max Units 15 80 500 85 15 10 12 V dc mA mA % V dc mA mA Min Typ. Max Units 10.6 0.6 V dc V dc Min Typ. Max units 3.65 9.5 1 V s s Min Typ. Max Units Note 7 After failure (Note 8) 0 VDD V dc Min Typ. Max Units Gx to Ex (Note 10) Gx to Ex (Note 10) Half-bridge mode 400 500 150 80 2.5 ns ns ns ns s Test conditions Min Typ. Max Units 1.4 5.6 mA V SOx to GND 1.5 VDD Page 3 2SB315A Data Sheet 2SB315A-CM1200DC-34N Electrical insulation Test conditions Min Typ. Max Operating voltage Test voltage Partial discharge extinction volt. Creep path input-output Creep path output-output Maximum dV/dt at dV=1000 V Continuous or repeated (Note 4) 1200 50 Hz/1 min (Note 11) 4000 >1700 IEC270 (Note 12) 21 25 Note 13 100 Units V dc V AC(eff) V AC(pk) mm mm kV/s All data refer to +25C and VDC = 15 V unless otherwise specified Footnotes to the key data 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) The drivers have a zener diode on each channel for over-voltage protection. When the feed voltage exceeds 16V, this protection may be exposed to thermal overload. If the specified power consumption is exceeded, this indicates an overload of the DC/DC converter. It should be noted that these DC/DC converters are not protected against overload. Application-specific self-heating of gate drivers and IGBT modules, especially at high switching frequency, must be taken into account. As a rule, the switching frequency is limited due to the switching losses of the IGBT modules. Because CONCEPT cannot predict how the drivers will be incorporated in the user's application, no binding recommended value for self-heating and thus for the maximum useable output power can be made. Users are therefore recommended to check the gate driver's ambient temperature within the system. This limit is due to active clamping. Refer to the "Description and Application Manual for 2SB315A SCALE Dual-Channel Plug-and-play IGBT Driver". Under-voltage monitoring of the supply voltage to the gate driver. If the voltage drops below this limit, the power modules are switched off. The gate current is limited by the gate resistors located on the driver. Pulse width of the direct output of the gate drive unit (excluding the delay of the gate resistors). The typical blocking time after an error is 1 second. Versions with other blocking times may also be supplied if required. Measured from the transition of the turn-on or turn-off command at the host controller to direct output of the gate drive unit (excluding the delay of the gate resistors). Refers to the direct output of the gate drive unit (excluding the delay of the gate resistors). The test voltage of 4000 V ac(rms) /50Hz may be applied only once during one minute. It should be noted that with this (strictly speaking obsolete) test method, some (minor) damage occurs to the insulation layers due to the partial discharge. Consequently, this test is not performed at CONCEPT as a series test. In the case of repeated insulation tests (e.g. module test, equipment test, system test), the subsequent tests should be performed with a lower test voltage: the test voltage is reduced by 400V for each additional test. The more modern if more elaborate partial-discharge measurement is preferable to such test methods as it is almost entirely non-destructive. The partial discharge is not measured for the standard types. Tested and selected types with guaranteed partial-discharge immunity can be supplied for applications with maximum requirements and higher operating voltages (such as railroad applications). This specification guarantees that the drive information will be transferred reliably even at a high DC-link voltage and with ultra-fast switching operations. Page 4 INTELLIGENT POWER ELECTRONICS 2SB315A Data Sheet 2SB315A-CM1200DC-34N Important Notice The data contained in this product data sheet is intended exclusively for technically trained staff. Handling all high-voltage equipment involves risk to life. Strict compliance with the respective safety regulations is mandatory! Any handling of electronic devices is subject to the general specifications for protecting electrostatic-sensitive devices according to international standard IEC 747-1, Chapter IX or European standard EN 100015 (i.e. the workplace, tools, etc. must comply with these standards). Otherwise, this product may be damaged. Legal Disclaimer This data sheet specifies devices but cannot promise to deliver any specific characteristics. No warranty or guarantee is given - either expressly or implicitly - regarding delivery, performance or suitability. CT-Concept Technologie AG reserves the right to make modifications to its technical data and product specifications at any time without prior notice. The general terms and conditions of delivery of CT-Concept Technologie AG apply. Technical Support CONCEPT provides expert help for your questions and problems: Internet: www.IGBT-Driver.com/go/support Quality The obligation to high quality is one of the central features laid down in the mission statement of CT-Concept Technologie AG. The quality management system covers all stages of product development and production up to delivery. The drivers of the SCALE series are manufactured to the ISO 9001 standard. IGBT-Driver.com Page 5 2SB315A Data Sheet 2SB315A-CM1200DC-34N Ordering Information The general terms and conditions of delivery of CT-Concept Technologie AG apply. Related IGBT CONCEPT Driver Type # Mitsubishi CM1200DC-34N Mitsubishi CM1200DB-34N 2SB315A-CM1200DC-34N 2SB315A-CM1200DC-34N Information about Other Products For drivers adapted to other high-voltage or high-power IGBT modules Direct link: www.IGBT-Driver.com/go/plug-and-play For other drivers and evaluation systems Please click: www.IGBT-Driver.com (c) Manufacturer CT-Concept Technologie AG Intelligent Power Electronics Renferstrasse 15 CH-2504 Biel-Bienne Switzerland Tel. Fax E-mail Internet +41 - 32 - 344 47 47 +41 - 32 - 344 47 40 Info@IGBT-Driver.com www.IGBT-Driver.com Copyright 2003...2010 by CT-Concept Technologie AG - Switzerland. We reserve the right to make any technical modifications without prior notice. Page 6 All rights reserved. Version of 2016-05-20 INTELLIGENT POWER ELECTRONICS Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Power Integrations: 2SB315A-CM1200DC-34N