UCC28C40, UCC28C41, UCC28C42, UCC28C43, UCC28C44, UCC28C45 UCC38C40, UCC38C41, UCC38C42, UCC38C43, UCC38C44, UCC38C45 SLUS458E -- AUGUST 2001 -- REVISED OCTOBER 2010 BiCMOS LOW-POWER CURRENT-MODE PWM CONTROLLER FEATURES DESCRIPTION D Enhanced Replacement for UC3842A Family D D D D D D D D D D UCC38C4x family is a high-performance currentmode PWM controller. It is an enhanced BiCMOS version with pin-for-pin compatibility to the industry standard UC384xA family and UC384x family of PWM controllers. In addition, lower startup voltage versions of 7 V are offered as UCC38C40 and UCC38C41. With Pin-to-Pin Compatibility 1-MHz Operation 50-A Standby Current, 100-A Maximum Low Operating Current of 2.3 mA at 52 kHz Fast 35-ns Cycle-by-Cycle Overcurrent Limiting 1-A Peak Output Current Rail-to-Rail Output Swings with 25-ns Rise and 20-ns Fall Times 1% Initial Trimmed 2.5-V Error Amplifier Reference Trimmed Oscillator Discharge Current New Under Voltage Lockout Versions MSOP-8 Package Minimizes Board Space Providing necessary features to control fixed frequency, peak current-mode power supplies, this family offers the following performance advantages. The device offers high-frequency operation up to 1 MHz with low start-up and operating currents, thus minimizing start-up loss and low operating power consumption for improved efficiency. The device also features a very fast current-sense-to-output delay time of 35 ns and a 1 A peak output current capability with improved rise and fall times for driving large external MOSFETs directly. APPLICATIONS D Switch-Mode Power Supplies D dc-to-dc Converters D Board Mount Power Modules The UCC38C4x family is offered in 8-pin packages, MSOP (DGK), SOIC (D) and PDIP (P). FUNCTIONAL BLOCK DIAGRAM 5.0 V 8 VREF UVLO + 7 VDD 5 GND 6 OUT + VREF VREF GOOD LOGIC RT/CT 4 OSC (NOTE) 2.5 V FB + ERROR AMP T 2R 2 R COMP 1 CS 3 1V S Q R Q Note: Toggle flip--flop used only in UCC38C41, UCC38C44, and UCC38C45. UDG--99139 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2003 -- 2010, Texas Instruments Incorporated www.ti.com 1 UCC28C40, UCC28C41, UCC28C42, UCC28C43, UCC28C44, UCC28C45 UCC38C40, UCC38C41, UCC38C42, UCC38C43, UCC38C44, UCC38C45 SLUS458E -- AUGUST 2001 -- REVISED OCTOBER 2010 recommended operating conditions MIN MAX Input voltage, VDD 18 Output voltage range, VOUT 18 V 200 mA --20 mA 105 C Average output current, IOUTW Reference output current, IOUT(ref)W Operating junction temperature, TJW UNIT --40 V It is not recommended that the device operate under conditions beyond those specified in this table for extended periods of time. absolute maximum ratings over operating free-air temperature (unless otherwise noted)}w Supply voltage (VDD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 V (MAX ICC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 mA Output current, IOUT peak . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 A Output energy, capacitive load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 J Voltage rating (COMP, CS, FB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . --0.3 V to 6.3 V (OUT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . --0.3 V to 20 V (RT/CT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . --0.3 V to 6.3 V (VREF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Error amplifier output sink current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 mA Total Power Dissipation at TA = 25C: D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 C/W DGK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120C/W P package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65C/W Operating junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . --55C to 150C Storage temperature range Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . --65C to 150C Lead Temperature (Soldering, 10 seconds) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltages are with respect to ground. Currents are positive into and negative out of the specified terminals. Consult the Packaging Section of the Databook for thermal limitations and considerations of the package. AVAILABLE OPTIONS TA = TJ MAXIMUM DUTY CYCLE 100% --40C 40C to 105C 50% 100% 0C 0 C to 70C 70 C 50% 2 UVLO ON/OFF SOIC--8 SMALL OUTLINE (D){ PDIP--8 PLASTIC DIP (P) MSOP--8 SMALL OUTLINE (DGK){ 14.5V / 9.0V UCC28C42D UCC28C42P UCC28C42DGK 8.4V / 7.6V UCC28C43D UCC28C43P UCC28C43DGK 7.0V / 6.6V UCC28C40D UCC28C40P UCC28C40DGK 14.5V / 9.0V UCC28C44D UCC28C44P UCC28C44DGK 8.4V / 7.6V UCC28C45D UCC28C45P UCC28C45DGK 7.0V / 6.6V UCC28C41D UCC28C41P UCC28C41DGK 14.5V / 9.0V UCC38C42D UCC38C42P UCC38C42DGK 8.4V / 7.6V UCC38C43D UCC38C43P UCC38C43DGK 7.0V / 6.6V UCC38C40D UCC38C40P UCC38C40DGK 14.5V / 9.0V UCC38C44D UCC38C44P UCC38C44DGK 8.4V / 7.6V UCC38C45D UCC38C45P UCC38C45DGK 7.0V / 6.6V UCC38C41D UCC38C41P UCC38C41DGK D (SOIC--8) and DGK (MSOP--8) packages are available taped and reeled. Add R suffix to device type (e.g. UCC28C42DR) to order quantities of 2500 devices per reel. Tube quantities are 75 for D packages (SOIC--8) and 80 for DGK package (MSOP--8), and 50 for P package (PDIP-8). www.ti.com UCC28C40, UCC28C41, UCC28C42, UCC28C43, UCC28C44, UCC28C45 UCC38C40, UCC38C41, UCC38C42, UCC38C43, UCC38C44, UCC38C45 SLUS458E -- AUGUST 2001 -- REVISED OCTOBER 2010 electrical characteristics VDD = 15 V (See Note 1), RT = 10 k, CT = 3.3 nF, CVDD = 0.1F and no load on the outputs, TA = --40C to 105C for the UCC28C4x and TA = 0C to 70C for the UCC38C4x, TA = TJ (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNITS Reference Section Output voltage, initial accuracy TA = 25C IOUT = 1mA 4.9 Line regulation VDD = 12 V to 18 V Load regulation 1mA to 20mA Temperature stability See Note 2 Total output variation See Note 2 Output noise voltage 10 Hz to 10 kHz, TA = 25C, See Note 2 Long term stability 1000 hours, TA = 125C, See Note 2 5.0 5.1 V 0.2 20 mV 3 25 mV 0.4 mV/C 0.2 4.82 Output short circuit 5.18 50 -30 V V 5 25 mV -45 -55 mA kHz Oscillator Section Initial accuracy TA = 25C, Voltage stability VDD = 12 V to 18 V See Note 3 Temperature stability TMIN to TMAX, Amplitude RT/CT Pin peak-to-peak 50.5 53 55 0.2% 1.0% 1% 2.5% See Note 2 1.9 RT/CT = 2 V, RT/CT = 2 V, See Note 4 Feedback input voltage, initial accuracy VCOMP = 2.5 V, TA = 25C Feedback input voltage, total variation VCOMP = 2.5 V, Input bias current VFB = 5.0 V Open-loop voltage gain (AVOL) VOUT = 2 V to 4 V 65 90 dB Unity gain bandwidth See Note 2 1.0 1.5 MHz Power supply rejection ratio (PSRR) VDD = 12 V to 18 V 60 Output sink current VFB = 2.7 V, VCOMP = 1.1 V Output source current VFB = 2.3 V, VCOMP = 5V High-level output voltage (VOH) VFB = 2.7 V, RLOAD = 15 k to GND Low-level output voltage (VOL) VFB = 2.7 V, RLOAD = 15 k to VREF Discharge current See Note 4 V TA = 25C, 7.7 8.4 9.0 mA 7.2 8.4 9.5 mA 2.475 2.500 2.525 2.45 2.50 2.55 V -0.1 -2.0 A Error Amplifier Section V dB 2 14 mA -0.5 -1.0 mA 5 6.8 V 0.1 1.1 V 2.85 3.00 3.15 V/V 0.9 1.0 1.1 V -0.1 -2.0 A 35 70 ns Current Sense Section Gain See Note 5, 6 Maximum input signal VFB < 2.4 V Power supply rejection ratio (PSRR) VDD = 12 V to 18 V, See Note 2, 5 Input bias current CS to output delay COMP to CS offset NOTE: NOTE: NOTE: NOTE: NOTE: VCS = 0 V 70 1.15 dB V 1. 2. 3. 4. 5. Adjust VDD above the start threshold before setting at 15 V. Ensured by design. Not production tested. Output frequencies of the UCC38C41, UCC38C44 and the UCC38C45 are half the oscillator frequency. Oscillator discharge current is measured with RT = 10 k to VREF. Parameter measured at trip point of latch with VFB = 0 V. V COM , 0V V 900mV NOTE: 6. Gain is defined as ACS = CS V CS www.ti.com 3 UCC28C40, UCC28C41, UCC28C42, UCC28C43, UCC28C44, UCC28C45 UCC38C40, UCC38C41, UCC38C42, UCC38C43, UCC38C44, UCC38C45 SLUS458E -- AUGUST 2001 -- REVISED OCTOBER 2010 electrical characteristics VDD = 15 V (See Note 1), RT = 10 k, CT = 3.3 nF, CVDD = 0.1F and no load on the outputs, TA = --40C to 105C for the UCC28C4x and TA = 0C to 70C for the UCC38C4x, TA = TJ (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNITS Output Section VOUT low (RDS(on) pull-down) ISINK = 200 mA 5.5 15 VOUThigh (RDS(on) pull-up) ISOURCE = 200 mA 10 25 Rise tIme TA = 25C, CLOAD = 1 nF 25 50 Fall time TA = 25C, CLOAD = 1 nF 20 40 ns Undervoltage Lockout Section Start threshold Minimum operating voltage UCC38C42, UCC38C44 13.5 14.5 15.5 UCC38C43, UCC38C45 7.8 8.4 9.0 UCC38C40, UCC38C41 6.5 7.0 7.5 UCC38C42, UCC38C44 8 9 10 UCC38C43, UCC38C45 7.0 7.6 8.2 UCC38C40, UCC38C41 6.1 6.6 7.1 UCC38C42, UCC38C43, UCC38C40, VFB < 2.4 V 94% 96% UCC38C44, UCC38C45, UCC38C41, VFB < 2.4 V 47% 48% V PWM Section Maximum duty cycle Minimum duty cycle VFB > 2.6 V 0% Current Supply Section Start-up current (ISTART-UP) VDD = Undervoltage lockout start threshold (--0.5 V) 50 100 A Operating supply current (IDD) VFB = VCS = 0 V 2.3 3.0 mA NOTE 1: Adjust VDD above the start threshold before setting at 15 V. PDIP (P) or SOIC (D) PACKAGE (TOP VIEW) COMP FB CS RT/CT 4 1 8 2 7 3 4 6 5 MSOP (DGK) PACKAGE (TOP VIEW) COMP FB CS RT/CT VREF VDD OUT GND www.ti.com 1 8 2 7 3 6 4 5 VREF VDD OUT GND UCC28C40, UCC28C41, UCC28C42, UCC28C43, UCC28C44, UCC28C45 UCC38C40, UCC38C41, UCC38C42, UCC38C43, UCC38C44, UCC38C45 SLUS458E -- AUGUST 2001 -- REVISED OCTOBER 2010 pin assignments COMP: This pin provides the output of the error amplifier for compensation. In addition, the COMP pin is frequently used as a control port by utilizing a secondary-side error amplifier to send an error signal across the secondary-primary isolation boundary through an opto-isolator. CS: The current sense pin is the non-inverting input to the PWM comparator. This is compared to a signal proportional to the error amplifier output voltage. A voltage ramp can be applied to this pin to run the device with a voltage mode control configuration. FB: This pin is the inverting input to the error amplifier. The non-inverting input to the error amplifier is internally trimmed to 2.5 V 1%. GND: Ground return pin for the output driver stage and the logic level controller section. OUT: The output of the on-chip drive stage. OUT is intended to directly drive a MOSFET. The OUT pin in the UCC38C40, UCC38C42 and UCC38C43 is the same frequency as the oscillator, and can operate near 100% duty cycle. In the UCC38C41, UCC38C44 and the UCC38C45, the frequency of OUT is one-half that of the oscillator due to an internal T flipflop. This limits the maximum duty cycle to < 50%. RT/CT: Timing resistor and timing capacitor. The timing capacitor should be connected to the device ground using minimal trace length. VDD: Power supply pin for the device. This pin should be bypassed with a 0.1-F capacitor with minimal trace lengths. Additional capacitance may be needed to provide hold up power to the device during startup. VREF: 5-V reference. For stability, the reference should be bypassed with a 0.1-F capacitor to ground using the minimal trace length possible. www.ti.com 5 UCC28C40, UCC28C41, UCC28C42, UCC28C43, UCC28C44, UCC28C45 UCC38C40, UCC38C41, UCC38C42, UCC38C43, UCC38C44, UCC38C45 SLUS458E -- AUGUST 2001 -- REVISED OCTOBER 2010 APPLICATION INFORMATION This device is a pin-for-pin replacement of the bipolar UC3842 family of controllers, the industry standard PWM controller for single-ended converters. Familiarity with this controller family is assumed. The UCC28C4x/UCC38C4x series is an enhanced replacement with pin-to-pin compatibility to the bipolar UC284x/UC384x and UC284xA/UC384xA families. The new series offers improved performance when compared to older bipolar devices and other competitive BiCMOS devices with similar functionality. Note that these improvements discussed below generally consist of tighter specification limits that are a subset of the older product ratings, maintaining drop-in capability. In new designs these improvements can be utilized to reduce the component count or enhance circuit performance when compared to the previously available devices. advantages This device increases the total circuit efficiency whether operating off-line or in dc input circuits. In off-line applications the low start-up current of this device reduces steady state power dissipation in the startup resistor, and the low operating current maximizes efficiency while running. The low running current also provides an efficiency boost in battery operated supplies. low voltage operation Two members of the UCC38C4x family are intended for applications that require a lower start-up voltage than the original family members. The UCC38C40 and UCC38C41 have a turn-on voltage of 7.0 V typical and exhibit hysteresis of 0.4 V for a turn-off voltage of 6.6 V. This reduced start-up voltage enables use in systems with lower voltages, such as 12-V battery systems which are nearly discharged. high speed operation The BiCMOS design allows operation at high frequencies that were not feasible in the predecessor bipolar devices. First, the output stage has been redesigned to drive the external power switch in approximately half the time of the earlier devices. Second, the internal oscillator is more robust with less variation as frequency increases. In addition, the current sense to output delay has been reduced by a factor of three, to 45ns typical. These features combine to provide a device capable of reliable high frequency operation. The UCC38C4x family oscillator is true to the curves of the original bipolar devices at lower frequencies yet extends the frequency programmability range to at least 1MHz. This allows the device to offer pin to pin capability where required yet capable of extending the operational range to the higher frequencies typical of latest applications. When the original UC3842 was released in 1984 most switching supplies operated between 20kHz and 100kHz. Today, the UCC38C4x can be used in designs cover a span roughly ten times higher than those numbers. start/run current improvements The start--up current is only 60 A typical, a significant reduction from the bipolar device's ratings of 300uA (UC384xA). For operation over the temperature range of --40 to 85C the UCC28C4x devices offer a maximum startup current of 100 A, an improvement over competitive BiCMOS devices. This allows the power supply designer to further optimize the selection of the startup resistor value to provide a more efficient design. In applications where low component cost overrides maximum efficiency the low run current of 2.3 mA, typical, may allow the control device to run directly through the single resistor to (+) rail, rather than needing a bootstrap winding on the power transformer, along with a rectifier. The start/run resistor for this case must also pass enough current to allow driving the primary switching MOSFET, which may be a few milliamps in small devices. 6 www.ti.com UCC28C40, UCC28C41, UCC28C42, UCC28C43, UCC28C44, UCC28C45 UCC38C40, UCC38C41, UCC38C42, UCC38C43, UCC38C44, UCC38C45 SLUS458E -- AUGUST 2001 -- REVISED OCTOBER 2010 APPLICATION INFORMATION 1% initial reference voltage The BiCMOS internal reference of 2.5 V has an enhanced design and utilizes production trim to allow initial accuracy of 1% at room temperature and 2% over the full temperature range. This can be used to eliminate an external reference in applications that do not require the extreme accuracy afforded by the additional device. This is very useful for nonisolated dc-to-dc applications where the control device is referenced to the same common as the output. It is also applicable in offline designs that regulate on the primary side of the isolation boundary by looking at a primary bias winding, or perhaps from a winding on the output inductor of a buck-derived circuit. reduced discharge current variation The original UC3842 oscillator did not have trimmed discharged current, and the parameter was not specified on the datasheet. Since many customers attempted to use the discharge current to set a crude deadtime limit the UC3842A family was released with a trimmed discharge current specified at 25C. The UCC28C4x/UCC38C4x series now offers even tighter control of this parameter, with approximately 3% accuracy at 25C, and less than 10% variation over temperature using the UCC28C4x devices. This level of accuracy can enable a meaningful limit to be programmed, a feature not currently seen in competitive BiCMOS devices. The improved oscillator and reference also contribute to decreased variation in the peak to peak variation in the oscillator waveform, which is often used as the basis for slope compensation for the complete power system. soft-start The following diagram provides a typical soft-start circuit for use with the UCC38C42. The values of R and C should be selected to bring the COMP pin up at a controlled rate, limiting the peak current supplied by the power stage. After the soft-start interval is complete the capacitor continues to charge to VREF, effectively removing the PNP transistor from circuit considerations. The optional diode in parallel with the resistor forces a soft-start each time the PWM goes through UVLO and the reference (VREF) goes low. Without the diode,the capacitor otherwise remains charged during a brief loss of supply or brown-out, and no soft-start is enabled upon reapplication of VIN. UCC38C42 VREF 8 COMP 1 GND 5 Figure 1 www.ti.com UDG--01072 7 UCC28C40, UCC28C41, UCC28C42, UCC28C43, UCC28C44, UCC28C45 UCC38C40, UCC38C41, UCC38C42, UCC38C43, UCC38C44, UCC38C45 SLUS458E -- AUGUST 2001 -- REVISED OCTOBER 2010 APPLICATION INFORMATION oscillator synchronization The UCC38C4x oscillator has the same synchronization characteristics as the original bipolar devices. Thus, the information in the Application Note U--100A, UC3842/3/4/5 Provides Low-Cost Current-Mode Control, (TI Literature No. SLUA143) still applies. The application note describes how a small resistor from the timing capacitor-to-ground can offer an insertion point for synchronization to an external clock, (see Figures 2 and 3). Figure 2 shows how the UCC38C42 can be synchronized to an external clock source. This allows precise control of frequency and dead time with a digital pulse train. 8 VREF 4 RT / CT RT SYNCHRONIZATION CIRCUIT INPUT CT 24 UCC38C42 PWM UDG--01069 Figure 2. Oscillator Synchronization Circuit CLOCK INPUT PWM OUT UPPER THRESHOLD LOW HIGH LOW LOWER THRESHOLD ON . OFF . ON . VCT (ANALOG) OUTPUT A UPPER THRESHOLD VCT LOWER THRESHOLD VSYNC (DIGITAL) COMBINED Figure 3. Synchronization to an External Clock 8 www.ti.com UDG--01070 UCC28C40, UCC28C41, UCC28C42, UCC28C43, UCC28C44, UCC28C45 UCC38C40, UCC38C41, UCC38C42, UCC38C43, UCC38C44, UCC38C45 SLUS458E -- AUGUST 2001 -- REVISED OCTOBER 2010 APPLICATION INFORMATION precautions The absolute maximum supply voltage is 20 V, including any transients that may be present. If this voltage is exceeded, device damage is likely. This is in contrast to the predecessor bipolar devices, which could survive up to 30 V. Thus, the supply pin should be decoupled as close to the ground pin as possible. Also, since no clamp is included in the device, the supply pin should be protected from external sources which could exceed the 20 V level. Careful layout of the printed board has always been a necessity for high frequency power supplies. As the device switching speeds and operating frequencies increase the layout of the converter becomes increasingly important. This 8-pin device has only a single ground for the logic and power connections. This forces the gate drive current pulses to flow through the same ground that the control circuit uses for reference. Thus, the interconnect inductance should be minimized as much as possible. One implication is to place the device (gate driver) circuitry close to the MOSFET it is driving. Note that this can conflict with the need for the error amplifier and the feedback path to be away from the noise generating components. circuit applications Figure 4 shows a typical off-line application. D50 F1 12 V OUT T1 AC INPUT 100 Vac -- 240 Vac EMI FILTER REQUIRED + R10 C12 BR1 D2 R11 C1A C52 C3 D51 C18 C55 R56 L50 5V OUT R12 RT1 C53 D6 C54 R55 C5 SEC COMMON R6 IC2 R50 UCC38C44 1 COMP REF 8 2 FB VCC 7 3 CS OUT 6 4 RT/CT GND 5 R16 Q1 IC2 C50 C13 R50 R53 R52 C51 K IC3 A R R54 UDG--01071 Figure 4. Typical Off-Line Application Figure 5 shows the forward converter with synchronous rectification. This application provides 48 V to 3.3 V at 10 A with over 85% efficiency and uses the UCC38C42 as the secondary-side controller and UCC3961 as the primary-side startup control device. www.ti.com 9 10 www.ti.com 46.4k 0.1uF C5 7 6 5 4 3 2 AGnd Ref Rt FB SS SD OVS R12 200 ucc3961 U1 R2 2 1 C7 8 9 10 11 12 13 14 T2 100pF Vs CS PGnd Out Vdd St UVS 2.4k R3 1.2k 4 3 R4 1.5k 300 R13 C8 1uF Q2 470pF C6 76.8k R5 R6 4.7 C25 0.047uF C10 2.7nF 0.1uF C9 R8 R10 1k 5.1k D1 R14 50k R15 20k 40% 0.33 R9 Q1 C22 4.7nF 20k R24 20k 402 R23 Q3 R25 20k 680pF 100 R28 R19 20 4.7 R26 C17 4700pF 3300pF C12 5.6nF C16 21.5k C23 R17 R16 BAR74 D3 BAR74 D5 R20 10 1500pF C11 4 3 2 1 4 3 2 1 Vcc DT Rt/Ct CS FB U2 LODR BTLO HIDR 7.5k R18 UCC38C4x PGND 5 6 7 8 C19 470uF 4700pF U4 TPS2832 IN BOOT COMP R27 4.7 10 R21 Q4 GND OUT Vcc REF 5 6 7 8 2uF C26 470uF C20 0.22uF C13 + R11 0.22uF 10nF 1 + C4 C3 470uF C1 R1 32.4k 10k D2 T1 C18 + VinN VinP R7 1nF C2 L1 4.7uH C14 1uF C24 0.1uF D6 BZX84C15LT1 PWRGND 0.1uF C21 3r3V 100 R22 C15 1uF UCC28C40, UCC28C41, UCC28C42, UCC28C43, UCC28C44, UCC28C45 UCC38C40, UCC38C41, UCC38C42, UCC38C43, UCC38C44, UCC38C45 SLUS458E -- AUGUST 2001 -- REVISED OCTOBER 2010 APPLICATION INFORMATION + Figure 5. Forward Converter with Synchronous Rectification Using the UCC38C42 as the Secondary-Side Controller UCC28C40, UCC28C41, UCC28C42, UCC28C43, UCC28C44, UCC28C45 UCC38C40, UCC38C41, UCC38C42, UCC38C43, UCC38C44, UCC38C45 SLUS458E -- AUGUST 2001 -- REVISED OCTOBER 2010 TYPICAL CHARACTERISTICS OSCILLATOR FREQUENCY vs TIMING RESISTANCE AND CAPACITANCE OSCILLATOR DISCHARGE CURRENT vs TEMPERATURE 9.5 10 M CT = 470 pF 1M f -- Frequency -- Hz IDISCH -- Oscillator Discharge Current -- mA CT = 220 pF CT = 1 nF 100 k 10 k CT = 4.7 nF CT = 2.2 nF 1k 1k 10 k 9.0 8.5 8.0 7.5 7.0 100 k --50 --25 0 Figure 6 1.8 90 180 1.6 160 1.4 70 140 60 120 50 100 40 80 60 PHASE MARGIN 10 1 10 100 1k 10 k 125 1.2 COMP to CS Gain -- (dB) GAIN Phase Margin -- () 200 0 100 COMP to CS OFFSET VOLTAGE (with CS = 0) vs TEMPERATURE 100 20 75 Figure 7 ERROR AMPLIFIER FREQUENCY RESPONSE 30 50 TJ -- Temperature -- C RT -- Timing Resistance -- 80 25 100 k 1M 1.0 0.8 0.6 40 0.4 20 0.2 0 10 M f -- Frequency -- Hz 0.0 --50 --25 0 25 50 75 100 125 TJ -- Temperature -- C Figure 8 Figure 9 www.ti.com 11 UCC28C40, UCC28C41, UCC28C42, UCC28C43, UCC28C44, UCC28C45 UCC38C40, UCC38C41, UCC38C42, UCC38C43, UCC38C44, UCC38C45 SLUS458E -- AUGUST 2001 -- REVISED OCTOBER 2010 TYPICAL CHARACTERISTICS REFERENCE VOLTAGE vs TEMPERATURE ERROR AMPLIFIER REFERENCE VOLTAGE vs TEMPERATURE 2.55 VEAREF -- Error Amplifier Reference Voltage -- V 5.05 VREF -- Reference Voltage -- V 5.04 5.03 5.02 5.01 5.00 4.99 4.98 4.97 4.96 4.95 --50 --25 0 25 50 75 100 2.54 2.53 2.52 2.51 2.50 2.49 2.48 2.47 2.46 2.45 125 --50 --25 TJ -- Temperature -- C 0 REFERENCE SHORT-CIRCUIT CURRENT vs TEMPERATURE 100 125 200 --37 IBIAS -- Error Amplifier Input Bias Current -- nA ISC -- Reference Short Circuit Current -- mA 75 ERROR AMPLIFIER INPUT BIAS CURRENT vs TEMPERATURE --35 --39 --41 --43 --45 --47 --49 --51 --53 --25 0 25 50 75 TJ -- Temperature -- C 100 125 150 100 50 0 --50 --100 --150 --200 --50 --25 0 25 50 75 TJ -- Temperature -- C Figure 13 Figure 12 12 50 Figure 11 Figure 10 --55 --50 25 TJ -- Temperature -- C www.ti.com 100 125 UCC28C40, UCC28C41, UCC28C42, UCC28C43, UCC28C44, UCC28C45 UCC38C40, UCC38C41, UCC38C42, UCC38C43, UCC38C44, UCC38C45 SLUS458E -- AUGUST 2001 -- REVISED OCTOBER 2010 TYPICAL CHARACTERISTICS 16 UNDERVOLTAGE LOCKOUT vs TEMPERATURE (UCC38C43 & UCC38C45) UNDERVOLTAGE LOCKOUT vs TEMPERATURE (UCC38C42 & UCC38C44) 9.0 15 VUVLO -- UVLO Voltage -- V 13 UVLO ON 12 UVLO OFF 11 10 9 8.6 8.4 8.2 8.0 7.8 7.6 8 7.4 7 7.2 --50 --25 0 25 50 75 100 125 UVLO OFF 7.0 --50 --25 0 TJ -- Temperature -- C Figure 14 25 50 75 TJ -- Temperature -- C 100 125 Figure 15 UNDERVOLTAGE LOCKOUT vs TEMPERATURE (UCC38C40 & UCC38C41) 7.3 7.2 UVLO ON 7.1 VUVLO -- UVLO Voltage -- V VUVLO -- UVLO Voltage -- V 14 6 UVLO ON 8.8 7.0 6.9 6.8 6.7 6.6 6.5 UVLO OFF 6.4 6.3 --50 --25 0 25 50 75 100 125 TJ -- Temperature -- C Figure 16 www.ti.com 13 UCC28C40, UCC28C41, UCC28C42, UCC28C43, UCC28C44, UCC28C45 UCC38C40, UCC38C41, UCC38C42, UCC38C43, UCC38C44, UCC38C45 SLUS458E -- AUGUST 2001 -- REVISED OCTOBER 2010 TYPICAL CHARACTERISTICS SUPPLY CURRENT vs TEMPERATURE SUPPLY CURRENT vs OSCILLATOR FREQUENCY 3.0 25 1-nF LOAD 20 2.8 IDD -- Supply Current -- mA IDD -- Supply Current -- mA 2.9 15 10 NO LOAD 2.7 2.6 2.5 2.4 NO LOAD 2.3 2.2 5 2.1 0 2.0 200 k 0k 400 k 600 k f -- Frequency -- Hz 800 k 1M --50 --25 0 Figure 17 40 OUTPUT RISE TIME AND FALL TIME vs TEMPERATURE 75 100 125 MAXIMUM DUTY CYCLE vs OSCILLATOR FREQUENCY 100 10% to 90% VDD = 12 V CT = 220 pF tr (1 nF) 90 30 tf (1 nF) 25 20 10 80 70 CT = 1 nF 60 15 --50 --25 0 25 50 75 100 125 TJ -- Temperature -- C 50 0 500 1000 1500 f -- Frequency -- kHz Figure 19 14 50 Figure 18 Duty Cycle -- % Output Rise and Fall TIme -- ns 35 25 TJ -- Temperature -- C Figure 20 www.ti.com 2000 2500 UCC28C40, UCC28C41, UCC28C42, UCC28C43, UCC28C44, UCC28C45 UCC38C40, UCC38C41, UCC38C42, UCC38C43, UCC38C44, UCC38C45 SLUS458E -- AUGUST 2001 -- REVISED OCTOBER 2010 TYPICAL CHARACTERISTICS MAXIMUM DUTY CYCLE vs TEMPERATURE 100 MAXIMUM DUTY CYCLE vs TEMPERATURE 50 Output Rise and Fall TIme -- ns UCC38C40 UCC38C42 UCC38C43 Maximum Duty Cycle -- % 98 96 94 92 UCC38C41 UCC38C44 UCC38C45 49 48 47 46 90 --50 --25 0 25 50 75 100 45 125 --50 --25 TJ -- Temperature -- C 50 75 100 125 Figure 22 CURRENT SENSE THRESHOLD VOLTAGE vs TEMPERATURE CS TO OUT DELAY TIME vs TEMPERATURE 70 65 1.05 tD -- CD to OUT Delay Time -- ns VCS_th -- Current Sense Threshold -- V 25 TJ -- Temperature -- C Figure 21 1.10 0 1.00 0.95 60 55 50 45 40 35 0.90 --50 --25 0 25 50 75 100 125 TJ -- Temperature -- C 30 --50 --25 0 25 50 75 100 125 TJ -- Temperature -- C Figure 23 Figure 24 www.ti.com 15 UCC28C40, UCC28C41, UCC28C42, UCC28C43, UCC28C44, UCC28C45 UCC38C40, UCC38C41, UCC38C42, UCC38C43, UCC38C44, UCC38C45 SLUS458E -- AUGUST 2001 -- REVISED OCTOBER 2010 Revision History Revision SLUS458D to SLUS458E, 10/2010 1) Updated Operating Juction Temperature in the Recommended Operating Conditions Table, from --55 to 150 to --40 to 105. 2) Updated Available Options Table heading from TA to TA = TJ. 16 www.ti.com PACKAGE OPTION ADDENDUM www.ti.com 16-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) UCC28C40D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC28C40DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC28C40DGK ACTIVE VSSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC28C40DGKG4 ACTIVE VSSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC28C40DGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC28C40DGKRG4 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC28C40DR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC28C40DRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC28C40P ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC28C40PG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC28C41D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC28C41DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC28C41DGK ACTIVE VSSOP DGK 8 100 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC28C41DGKG4 ACTIVE VSSOP DGK 8 100 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC28C41DGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC28C41DGKRG4 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC28C41DR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 1 Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 16-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) UCC28C41DRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC28C42D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC28C42DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC28C42DGK ACTIVE VSSOP DGK 8 100 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC28C42DGKG4 ACTIVE VSSOP DGK 8 100 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC28C42DGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC28C42DGKRG4 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC28C42DR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC28C42DRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC28C42P ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC28C42PG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC28C43D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC28C43DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC28C43DGK ACTIVE VSSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC28C43DGKG4 ACTIVE VSSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC28C43DGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC28C43DGKRG4 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC28C43DR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 2 Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 16-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) UCC28C43DRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC28C43P ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC28C43PG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC28C44D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC28C44DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC28C44DGK ACTIVE VSSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC28C44DGKG4 ACTIVE VSSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC28C44DGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC28C44DGKRG4 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC28C44DR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC28C44DRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC28C44P ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC28C44PG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC28C45D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC28C45DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC28C45DGK ACTIVE VSSOP DGK 8 100 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC28C45DGKG4 ACTIVE VSSOP DGK 8 100 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC28C45DGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR Addendum-Page 3 Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 16-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) UCC28C45DGKRG4 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC28C45DR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC28C45DRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC28C45P ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC28C45PG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC38C40D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC38C40DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC38C40DGK ACTIVE VSSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC38C40DGKG4 ACTIVE VSSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC38C40DGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC38C40DGKRG4 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC38C40DR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC38C40DRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC38C40P ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC38C40PG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC38C41D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC38C41DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC38C41DGK ACTIVE VSSOP DGK 8 100 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR Addendum-Page 4 Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 16-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) UCC38C41DGKG4 ACTIVE VSSOP DGK 8 100 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC38C41DR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC38C41DRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC38C41P ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC38C41PG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC38C42D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC38C42DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC38C42DGK ACTIVE VSSOP DGK 8 100 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC38C42DGKG4 ACTIVE VSSOP DGK 8 100 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC38C42DGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC38C42DGKRG4 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC38C42DR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC38C42DRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC38C42P ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC38C42PG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC38C43D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC38C43DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC38C43DGK ACTIVE VSSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR Addendum-Page 5 Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 16-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) UCC38C43DGKG4 ACTIVE VSSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC38C43DGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC38C43DGKRG4 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC38C43DR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC38C43DRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC38C43P ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC38C43PG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC38C44D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC38C44DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC38C44DGK ACTIVE VSSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC38C44DGKG4 ACTIVE VSSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC38C44DGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC38C44DGKRG4 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC38C44DR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC38C44DRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC38C44P ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC38C44PG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC38C45D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 6 Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 16-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) UCC38C45DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC38C45DGK ACTIVE VSSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC38C45DGKG4 ACTIVE VSSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC38C45DGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC38C45DGKRG4 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR UCC38C45DR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC38C45DRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC38C45P ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC38C45PG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Addendum-Page 7 PACKAGE OPTION ADDENDUM www.ti.com 16-Aug-2012 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF UCC28C41, UCC28C43, UCC28C45 : * Automotive: UCC28C41-Q1 * Enhanced Product: UCC28C43-EP, UCC28C45-EP NOTE: Qualified Version Definitions: * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects * Enhanced Product - Supports Defense, Aerospace and Medical Applications Addendum-Page 8 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device UCC28C40DGKR Package Package Pins Type Drawing VSSOP SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 UCC28C40DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 UCC28C41DGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 UCC28C41DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 UCC28C42DGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 UCC28C42DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 UCC28C43DGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 UCC28C43DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 UCC28C44DGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 UCC28C44DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 UCC28C45DGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 UCC28C45DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 UCC38C40DGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 UCC38C40DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 UCC38C41DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 UCC38C42DGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 UCC38C42DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 UCC38C43DGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2012 Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant UCC38C43DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 UCC38C44DGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 UCC38C44DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 UCC38C45DGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 UCC38C45DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) UCC28C40DGKR VSSOP DGK 8 2500 366.0 364.0 50.0 UCC28C40DR SOIC D 8 2500 340.5 338.1 20.6 UCC28C41DGKR VSSOP DGK 8 2500 367.0 367.0 35.0 UCC28C41DR SOIC D 8 2500 340.5 338.1 20.6 UCC28C42DGKR VSSOP DGK 8 2500 367.0 367.0 35.0 UCC28C42DR SOIC D 8 2500 340.5 338.1 20.6 UCC28C43DGKR VSSOP DGK 8 2500 367.0 367.0 35.0 UCC28C43DR SOIC D 8 2500 340.5 338.1 20.6 UCC28C44DGKR VSSOP DGK 8 2500 366.0 364.0 50.0 UCC28C44DR SOIC D 8 2500 340.5 338.1 20.6 UCC28C45DGKR VSSOP DGK 8 2500 366.0 364.0 50.0 UCC28C45DR SOIC D 8 2500 340.5 338.1 20.6 Pack Materials-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2012 Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) UCC38C40DGKR VSSOP DGK 8 2500 367.0 367.0 35.0 UCC38C40DR SOIC D 8 2500 340.5 338.1 20.6 UCC38C41DR SOIC D 8 2500 340.5 338.1 20.6 UCC38C42DGKR VSSOP DGK 8 2500 367.0 367.0 35.0 UCC38C42DR SOIC D 8 2500 340.5 338.1 20.6 UCC38C43DGKR VSSOP DGK 8 2500 367.0 367.0 35.0 UCC38C43DR SOIC D 8 2500 340.5 338.1 20.6 UCC38C44DGKR VSSOP DGK 8 2500 367.0 367.0 35.0 UCC38C44DR SOIC D 8 2500 340.5 338.1 20.6 UCC38C45DGKR VSSOP DGK 8 2500 367.0 367.0 35.0 UCC38C45DR SOIC D 8 2500 340.5 338.1 20.6 Pack Materials-Page 3 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated