a u s t ri a m i c r o s y s t e m s AS1751 , AS1752, AS1753 D a ta S he e t H i g h - Sp e e d , L o w - Vo l ta g e , S i n g l e - S u p p l y, 0 . 9 , Q u a d S P S T A n a l o g S w i t c h e s 1 General Description 2 Key Features The AS1751/AS1752/AS1753 are high-speed, low-voltage, quad single-pole/single-throw (SPST) analog switches. ! ON-Resistance: - 0.9 (+3V supply) - 2.5 (+1.8V supply) Fast switching speeds, low ON-resistance, and low power consumption make these devices ideal for singlecell battery powered applications. ! RON Matching: - 0.12 (+3V supply) - 0.25 (+1.8V supply) ! RON Flatness: 0.1 (+3V Supply) ! Supply Voltage Range: +1.6 to +3.6V ! Switching Speed: tON = 22ns, tOFF = 14ns ! Current-Handling: 250mA Continuous These highly-reliable devices operate from a single +1.6 to +3.6V supply, and are differentiated by the type and number of switches: ! AS1751 - Four normally open (NO) switches ! AS1752 - Four normally closed (NC) switches ! Break-Before-Make Switching (AS1753) ! AS1753 - Two NO switches and Two NC switches ! Rail-to-Rail Signal Handling ! 1.8V CMOS Logic Compatible (+3V Supply) ! Operating Temperature Range: -40 to +85C ! Package Types: - 16-pin QFN (3mm x 3mm) - 14-pin TSSOP The AS1753 supports break-before-make switching. With very low ON-resistance (RON), RON matching and RON flatness, the devices can accurately switch signals for sample and hold circuits, digital filters, and op-amp gain switching networks. The AS1751/AS1752/AS1753 digital logic input is 1.8V CMOS-compatible when using a +3V supply, and all devices can handle Rail-to-Rail signals. The devices are available in a 3mm x 3mm 16-pin QFN package and a 14-pin TSSOP package. Figure 1. 14-pin TSSOP Block Diagrams AS1751 3 Applications The devices are ideal for use in power routing systems, cordless and mobile phones, MP3 players, CD and DVD players, PDAs, handheld computers, digital cameras, hard drives, and any other application where high-speed signal switching is required. AS1752 AS1753 1 NO1 14 V+ 1 NC1 14 V+ 1 NO1 14 V+ 2 COM1 13 IN1 2 COM1 13 IN1 2 COM1 13 IN1 3 NO2 12 IN4 3 NC2 12 IN4 3 NC2 12 IN4 4 COM2 11 NO4 4 COM2 11 NC4 4 COM2 11 NC4 5 IN2 10 COM4 5 IN2 10 COM4 5 IN2 10 COM4 6 IN3 9 COM3 6 IN3 9 COM3 6 IN3 9 COM3 7 GND 8 NO3 Device AS1751 AS1752 AS1753 www.austriamicrosystems.com 7 GND Input Low High Low High Low High 8 NC3 7 GND 8 NO3 Switch State Off On On Off Switches 1, 3 = Off Switches 2, 4 = On Switches 1, 3 = On Switches 2, 4 = Off Revision 1.4 1 - 16 austriam i c r o systems AS1751, AS1752, AS1753 Data Sheet 4 Absolute Maximum Ratings Stresses beyond those listed in Table 1 may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in Section 5 Electrical Characteristics on page 3 is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 1. Absolute Maximum Ratings Parameter Min Max Units V+, INx to GND -0.3 +5 V -0.3 V+ + 0.3 V COMx, NOx, NCx Continuous Current -250 +250 mA COMx, NOx, NCx Peak Current -350 +350 mA COMx, NOx, NCx to GND 16-pin QFN Continuous Power Dissipation (TAMB = +70C) 14-pin TSSOP Operating Temperature Range 727 1349 -40 mW Comments Pulsed at 1ms 10% duty cycle Derate at 9.1W/C above +70C Derate at 16.9W/C above +70C +85 C 2500 V HBM Mil-Std883E 3015.7 methods Latch Up Immunity 250 mA Norm: JEDEC 17 Junction Temperature +150 C +150 C Electro-Static Discharge Storage Temperature Range Package Body Temperature -65 +260 C The reflow peak soldering temperature (body temperature) specified is in accordance with IPC/JEDEC J-STD-020C "Moisture/Reflow Sensitivity Classification for Non-Hermetic Solid State Surface Mount Devices" Signals on pins COM1, COM3, NO1, NO2, NC1, or NC2 that exceed V+ or GND are clamped by internal diodes. Forward-diode current should be limited to the maximum current rating. - www.austriamicrosystems.com Revision 1.4 2 - 16 austriam i c r o systems AS1751, AS1752, AS1753 Data Sheet 5 Electrical Characteristics Table 2. Power Supply Characteristics Symbol Parameter Conditions Min V+ Power Supply Range TAMB = TMIN to TMAX 1.6 I+ Positive Supply Current V+ = 3.6V, VINx = 0 or V+, TAMB = +25C Typ Max Unit 3.6 V 0.1 A V+ = +2.7 to +3.6V, VIH = +1.4V, VIL = +0.5V, TAMB = TMIN to TMAX (unless otherwise specified). Typ values @ V+ = +3.0V, TAMB = +25C. Table 3. +3V Supply Electrical Characteristics Symbol Parameter Conditions Min Typ Max Unit Analog Switch VCOMx, VNOx, VNCx Analog Signal Range RON ON-Resistance V+ = 2.7V, ICOMx = 100mA, VNOx or VNCx = 1.5V RON ON-Resistance Match 1 Between Channels V+ = 2.7V, ICOMx = 100mA, VNOx or VNCx = 1.5V RFLAT(ON) ON-Resistance 2 Flatness V+ = 2.7V, ICOMx = 100mA, VNOx or VNCx = 1, 1.5, or 2V INOx(OFF), INCx(OFF) NOx or NCx Off-Leakage Current V+ = 3.6V, VCOMx = 0.3 or 3.6V, VNOx or VNCx = 3.6 or 0.3V ICOMx(OFF) COMx Off-Leakage Current V+ = 3.6V, VCOMx = 0.3 or 3.6V, VNOx or VNCx = 3.6 or 0.3V ICOMx(ON) COMx On-Leakage Current V+ = 3.6V, VCOMx = 0.3 or 3.6V, VNOx or VNCx = 0.3 or 3.6V 0 TAMB = +25C V+ 0.4 TAMB = TMIN to TMAX 0.9 1 TAMB = +25C 0.03 TAMB = TMIN to TMAX 0.12 0.15 TAMB = +25C 0.02 TAMB = TMIN to TMAX 0.1 0.12 TAMB = +25C -2.5 +2.5 TAMB = TMIN to TMAX -10 +10 TAMB = +25C -2.5 +2.5 TAMB = TMIN to TMAX -10 +10 TAMB = +25C -2.5 +2.5 TAMB = TMIN to TMAX -10 +10 V nA nA nA Switch Dynamic Characteristics VNOx or VNCx = 1.5V, RLOAD = 50, CLOAD = 35pF, Figures 11, 12 3 tON Turn On Time tOFF Turn Off Time tBBM Break-Before-Make VNOx or VNCx = 1.5V, RLOAD = 50, CLOAD = 35pF, Figures 11, 12 3 3 VNOx or VNCx = 1.5V, RLOAD = 50, CLOAD = 35pF, Figure 13 (AS1753) TAMB = +25C 16 TAMB = TMIN to TMAX 24 TAMB = +25C 5 TAMB = TMIN to TMAX 14 15 TAMB = +25C TAMB = TMIN to TMAX 22 11 2 ns ns ns Q Charge Injection VGEN = V+, RGEN = 0, CLOAD = 1.0nF, Figure 14 2 pC COFF NOx, NCx Off-Capacitance f = 1MHz, Figure 15 45 pF CCOMx(OFF) COMx Off-Capacitance f = 1MHz, Figure 15 49 pF CCOMx(ON) COMx On-Capacitance f = 1MHz, Figure 15 85 pF www.austriamicrosystems.com Revision 1.4 3 - 16 austriam i c r o systems AS1751, AS1752, AS1753 Data Sheet Table 3. +3V Supply Electrical Characteristics (Continued) Symbol Parameter VISO Off-Isolation Crosstalk Conditions 4 5 Total Harmonic Distortion THD Min Typ f = 10MHz, RLOAD = 50, CLOAD = 5pF, Figure 16 -40 f = 1MHz, RLOAD = 50, CLOAD = 5pF, Figure 16 -55 f = 10MHz, RLOAD = 50, CLOAD = 5pF, Figure 16 -70 f = 1MHz, RLOAD = 50, CLOAD = 5pF, Figure 16 -80 f = 20Hz to 20kHz, VCOMx = 2Vp-p, RLOAD = 32 0.033 Max Unit dB dB % Logic Input VIH Input Logic High VIL Input Logic Low IIN Input Leakage Current 1.4 VINx = 0 or V+ -1 V 0.0001 0.5 V +1 A V+ = +1.8V, VIH = +1.0V, VIL = 0.4V, TAMB = TMIN to TMAX (unless otherwise specified). Typ values @ TAMB = +25C. Table 4. +1.8V Supply Electrical Characteristics Symbol Parameter Conditions Min Typ Max Unit V+ V Analog Switch VCOMx, VNOx, VNCx Analog Signal Range RON ON-Resistance V+ = 1.8V, ICOMx = 10mA, VNOx or VNCx = 0.9V RON ON-Resistance Match Between 1 Channels V+ = 1.8V, ICOMx = 10mA, VNOx or VNCx = 0.9V 0 TAMB = +25C 0.9 TAMB = TMIN to TMAX 2.5 3 TAMB = +25C 0.05 TAMB = TMIN to TMAX 0.25 0.25 Switch Dynamic Characteristics tON Turn On Time tOFF Turn Off Time Q 3 3 Charge Injection VNOx or VNCx = 1.0V, TAMB = +25C RLOAD = 50, CLOAD = 35pF, TAMB = TMIN to TMAX Figures 11, 12 22 VNOx or VNCx = 1.0V, TAMB = +25C RLOAD = 50, CLOAD = 35pF, TAMB = TMIN to TMAX Figures 11, 12 12 VGEN = V+, RGEN = 0, CLOAD = 1.0nF, Figure 14 1 30 35 20 25 ns ns pC Logic Input VIH Input Logic High VIL Input Logic Low IIN Input Leakage Current 1.0 VINx = 0 or V+ -1 V 0.0001 0.4 V +1 A 1. RON = RON(MAX) - RON(MIN). 2. Flatness is defined as the difference between the maximum and the minimum value of ON-resistance as measured over the specified analog signal ranges. 3. Guaranteed by design. 4. Off-Isolation = 20log10(VCOMx/VNOx), VCOMx = output, VNOx = input to off switch. 5. Between two switches. www.austriamicrosystems.com Revision 1.4 4 - 16 austriam i c r o systems AS1751, AS1752, AS1753 Data Sheet 6 Typical Operating Characteristics Figure 2. Frequency Response Figure 3. Total Harmonic Distortion vs. Frequency 0.04 10 0 VDD = 3V 0.03 -20 -30 THD (%) Response (dB) 0.035 Bandwidth -10 -40 -50 -60 -70 0.025 0.02 0.015 0.01 -80 0.005 -90 -100 0.01 0 0.1 1 10 100 1 1000 10 Figure 4. Turn On/Turn Off Time vs. Temperature 18 tON Time (ns) Time (ns) 14 12 10 8 6 tOFF 2 0 -40 -15 10 35 60 26 24 22 20 18 16 14 12 10 8 6 4 2 0 85 tON tOFF 1.6 2 Temperature (C) 2.4 2.8 3.2 3.6 Supply Voltage (V) Figure 6. RON vs. VCOM and Temperature; VDD = 2.7V Figure 7. RON vs. VCOM 1.0 0.50 Temp = +85C 0.45 VDD = 1.8V 0.9 0.8 RON ( ) 0.40 RON ( ) 10000 100000 Figure 5. Turn On/Off Time vs. Supply Voltage 20 4 1000 Frequency (Hz) Frequency (MHz) 16 100 Temp = +25C 0.35 0.30 0.7 VDD = 2V VDD = 2.7V VDD = 3V 0.6 VDD = 2.5V 0.5 Temp = -40C 0.25 VDD = 3.3V 0.4 0.20 VDD = 3.6V 0.3 0 0.5 1 1.5 2 2.5 3 0 1 1.5 2 2.5 3 3.5 VCOM (V) VCOM (V) www.austriamicrosystems.com 0.5 Revision 1.4 5 - 16 austriam i c r o systems AS1751, AS1752, AS1753 Data Sheet Figure 8. Charge Injection vs. VCOM 60 50 Q (pC) 40 30 VDD = 3V 20 VDD = 1.8V 10 0 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 VCOM (V) www.austriamicrosystems.com Revision 1.4 6 - 16 austriam i c r o systems AS1751, AS1752, AS1753 Data Sheet ON-Resistance 7 Detailed Description The AS1751/AS1752/AS1753 are low ON-resistance, low-voltage, quad analog SPST switches that operate from a single +1.6 to +3.6V supply. CMOS process technology allows switching of analog signals that are within the supply voltage range (GND to V+). AS1752 16 COM1 15 NO1 14 V+ 13 IN1 12 IN4 11 NC4 10 N/C 9 COM4 1 NC2 2 COM2 3 N/C 4 IN2 12 IN4 11 NC4 10 N/C 9 COM4 AS1753 5 IN3 6 GND 7 NO3 8 COM3 1 NC2 2 COM2 3 N/C 4 IN2 5 IN3 6 GND 7 NO3 8 COM3 AS1751 12 IN4 11 NO4 10 N/C 9 COM4 5 IN3 6 GND 7 NC3 8 COM3 1 NO2 2 COM2 3 N/C 4 IN2 16 COM1 15 NC1 14 V+ 13 IN1 16 COM1 15 NO1 14 V+ 13 IN1 Figure 9. 16-pin QFN Block Diagrams Table 5. Truth Tables Device AS1751 AS1752 AS1753 Input Switch State Low Off High On Low On High Off Low Switches 1, 3 = Off Switches 2, 4 = On High Switches 1, 3 = On Switches 2, 4 = Off ON-Resistance When powered from a +3V supply, the low (0.9, max) ON-resistance allows high-speed, continuous signals to be switched in a variety of applications. Bi-Directional Switching Pins NOx, NCx, and COMx are bi-directional, thus they can be used as inputs to- or outputs from other components. Analog Signal Levels Analog signals ranging over the entire supply voltage range (V+ to GND) can be switched with very little change in ONresistance (see Typical Operating Characteristics on page 5). Logic Inputs The devices' logic inputs can be driven up to +3.6V regardless of the supply voltage value. For example, with a +1.8V supply, INx may be driven low to GND and high to +3.6V. This allows the devices to interface with +3V systems using a supply of less than 3V. www.austriamicrosystems.com Revision 1.4 7 - 16 austriam i c r o systems AS1751, AS1752, AS1753 Data Sheet Power Supply Sequencing 8 Application Information Power Supply Sequencing Proper power-supply sequencing is critical for proper switch operation. The power supplies should be started up in the following sequence: 1. V+ 2. NOx, NCx, COMx Note: Do not exceed the absolute maximum ratings (see page 2). Overvoltage Protection ON-resistance increases slightly at lower supply voltages. Figure 10. Overvoltage Protection using 2 External Blocking Diodes AS1751/AS1752/AS1753 D1 V+ V+ COMx NOx VGEN GND D2 Adding diode D2 to the circuit shown in Figure 10 causes the logic threshold to be shifted relative to GND. Diodes D1 and D2 also protect against overvoltage conditions. For example, in the circuit shown in Figure 10, if the supply voltage goes below the absolute maximum rating, and if a fault voltage up to the absolute maximum rating is applied to an analog signal pin, no damage will result. Power Supply Bypass Power supply connections to the devices must maintain a low impedance to ground. This can be done using a bypass capacitor, which will also improve noise margin and prevent switching noise propagation from the V+ supply to other components. A 0.1F bypass capacitor, connected from V+ to GND (see Figure 16 on page 10), is adequate for most applications. Logic Inputs Driving INx Rail-to-Rail will help minimize power consumption. Layout Considerations High-speed switches require proper layout and design procedures for optimum performance. ! Short, wide traces should be used to reduce stray inductance and capacitance. ! Bypass capacitors should be as close to the device as possible. ! Large ground planes should be used wherever possible. www.austriamicrosystems.com Revision 1.4 8 - 16 austriam i c r o systems AS1751, AS1752, AS1753 Data Sheet Timing Diagrams and Test Setups Timing Diagrams and Test Setups Figure 11. AS1751/AS1753 Test Circuit and Timing Diagram V+ NOx V+ VNOx AS1751/ AS1753 50 INx COMx tR < 5ns tF < 5ns VIH + 0.5V INx 50% 50% 0 VCOMx 50 35pF GND VNOx VCOMx 0 90% 90% tOFF tON Figure 12. AS1752/AS1753 Test Circuit and Timing Diagram V+ NCx V+ VNCx AS1752/ AS1753 INx INx 50% 50% 0 VCOMx COMx 50 tR < 5ns tF < 5ns VIH + 0.5V 50 35pF VNCx VCOMx 0 90% 90% GND tON tOFF Figure 13. AS1753 Test Circuit and Timing Diagram VS NC2 V+ NO1 INx 0 V+ AS1753 VS COM1 INx VCOMx COM2 50 tR < 5ns tF < 5ns VIH + 0.5V VS 50 35pF VCOMx 90% 90% 0 GND tBBM tBBM tBBM = tON(NOx) - tOFF(NCx) or tBBM = tON(NCx) - tOFF(NOx) Figure 14. Charge Injection V+ NCx or NOx V+ V+ RGEN VIN COMx 50 GND www.austriamicrosystems.com 0 VGEN AS175x INx VIN AS1751 AS1752 VOUT CLOAD 1000pF VOUT VOUT VOUT is the measured voltage due to charge transfer error Q when the channel turns off. Q = VOUT x CLOAD Revision 1.4 9 - 16 austriam i c r o systems AS1751, AS1752, AS1753 Data Sheet Timing Diagrams and Test Setups Figure 15. NOx, NCx, and COMx Capacitance AS1751/ AS1752/ AS1753 V+ V+ COMx 1MHz Capacitance Analyzer As Required INx GND NCx or NOx Figure 16. Off-Isolation, On-Loss, and Crosstalk Network Analyzer V+ V+ 0.1F VIN NOx or NCx 50 AS1751/ AS1752/ AS1753 Measure COMx INx 50 Reference VOUT GND 50 50 Use 50 termination for off-isolation Notes: 1. Measurements are standardized against short-circuit at socket terminals. 2. Off-isolation is measured between COMx and the off NCx/NOx terminal on each switch. Off-isolation = 20log (VOUT/ VIN). 3. On-loss is measured between COMx and the on NCx/NOx terminal on each switch. On-loss = 20log (VOUT/VIN). 4. Signal direction through the switch is reversed; worst values are recorded. www.austriamicrosystems.com Revision 1.4 10 - 16 austriam i c r o systems AS1751, AS1752, AS1753 Data Sheet Pin Assignments 9 Pinout and Packaging Pin Assignments 3 - - 9 COM4 IN3 5 13 IN1 14 V+ 15 NO1 16 COM1 14 V+ 15 NC1 13 IN1 10 IN2 4 COM3 8 NO3 7 GND 6 IN3 5 - 11 NC4 AS1753 3 10 IN2 4 - 9 COM4 COM3 8 - 9 COM4 AS1752 12 IN4 COM2 2 NO3 7 10 IN2 4 NC2 1 11 NC4 GND 6 3 12 IN4 COM2 2 IN3 5 AS1751 NC2 1 COM3 8 11 NO4 NC3 7 12 IN4 COM2 2 GND 6 NO2 1 - 16 COM1 13 IN1 14 V+ 15 NO1 16 COM1 Figure 17. QFN Pin Assignments (Top View) Figure 18. TSSOP Pin Assignments (Top View) NO1 1 14 V+ COM1 2 NO2 3 COM2 4 AS1751 NC1 1 14 V+ NO1 1 13 IN1 COM1 2 13 IN1 COM1 2 12 IN4 NC2 3 12 IN4 NC2 3 11 NO4 COM2 4 AS1752 11 NC4 COM2 4 14 V+ 13 IN1 12 IN4 AS1753 11 NC4 IN2 5 10 COM4 IN2 5 10 COM4 IN2 5 10 COM4 IN3 6 9 COM3 IN3 6 9 COM3 IN3 6 9 COM3 GND 7 8 NO3 GND 7 8 NC3 GND 7 8 NO3 Pin Descriptions Table 6. Pin Descriptions Pin Number (see Figure 17 and Figure 18) Pin Name Description COM1: COM4 Analog Switch 1, 2, 3, 4 Common GND Ground IN1:IN4 Analog Switch 1, 2, 3, 4 Logic Control Input NC1:NC4 Analog Switch 1, 2, 3, 4 Normally Closed Terminal NO1:NO4 Analog Switch 1, 2, 3, 4 Normally Open Terminal V+ Input Supply Voltage, +1.6 to +3.6V www.austriamicrosystems.com Revision 1.4 11 - 16 austriam i c r o systems AS1751, AS1752, AS1753 Data Sheet Package Drawings and Markings Package Drawings and Markings The devices are available in an 16-pin QFN package and an 14-pin TSSOP package. Figure 19. 16-pin QFN Package D2 -A- D D2/2 D/2 INDEX AREA (D/2 xE/2) -B- -B- aaa C 2x E SEE DETAIL B E2 E2/2 e E/2 NXL 4 2 1 PIN 1 MARKER N N-1 aaa C 2x 6 SEE DETAIL B 4 TOP VIEW NXb -A- INDEX AREA (D/2 xE/2) 5 bbb ddd C A B C BTM VIEW 11 NX 0.08 C A ccc C SEATING PLANE 9 Symbol Datum A or B L1 12 DETAIL B Common Dimensions Min Nom Max e Terminal Tip 5 EVEN TERMINAL SIDE www.austriamicrosystems.com Revision 1.4 Notes aaa 0.15 1, 2 bbb 0.10 1, 2 ccc 0.10 1, 2 ddd 0.05 1, 2 A 0.70 0.75 0.80 A1 0.00 0.02 0.05 0.20 Ref A3 e/2 -C- A3 8 A1 SIDE VIEW L1 0.03 0.15 D BSC 3.00 1, 2, 10 E BSC 3.00 1, 2, 10 D2 1.30 1.45 1.55 1, 2, 10 E2 1.30 1.45 1.55 1, 2, 10 L 0.30 0.40 0.50 1, 2, 10 N 16 1, 2, 10 ND 4 1, 2, 10 NE 4 1, 2, 10 12 - 16 austriam i c r o systems AS1751, AS1752, AS1753 Data Sheet Package Drawings and Markings Notes: 1. 2. 3. 4. Dimensioning and tolerancing conform to ASME Y14.5M-1994. All dimensions are in millimeters; angles in degrees. N is the total number of terminals. The terminal #1 identifier and terminal numbering convention shall conform to JEDEC 95 SPP-012. Details of terminal #1 identifier are optional but must be located within the zone indicated. The terminal #1 identifier may be either a mold or marked feature. 5. Dimension b applies to metallized terminal and is measured between 0.15 and 0.30mm from terminal tip. If one end of the terminal has the optional radius, the b dimension should not be measured in that radius area. 6. Dimensions ND and NE refer to the number of terminals on each D and E side, respectively. 7. Depopulation is possible in a symmetrical fashion. 8. Figure 19 is shown for illustration only and does not represent any specific variation. 9. All variations may be constructed per Figure 19, however variations may alternately be constructed between square or rectangle shape per dimensions D and E. 10. Refer to the Dimensions Table for a complete set of dimensions. 11. Bilateral coplanarity zone applies to the exposed heat sink slug as well as the terminals. 12. Depending on the method of lead termination at the edge of the package, pullback (L1) may be present. L minus L1 to be 0.33mm. 13. For variations with more than one lead count for a given body size and terminal pitch, each lead count for that variation is denoted by a dash number (e.g., -1 or -2). 14. NJR designates non-JEDEC registered package. www.austriamicrosystems.com Revision 1.4 13 - 16 austriam i c r o systems AS1751, AS1752, AS1753 Data Sheet Package Drawings and Markings Figure 20. 14-pin TSSOP Package Symbol A A1 A2 L R R1 b b1 c c1 D E1 E 1, 2 0.65mm Lead Pitch Min Nom Max 1.10 0.05 0.15 0.85 0.90 0.95 0.50 0.60 0.75 0.09 0.09 0.19 0.30 0.19 0.22 0.25 0.09 0.20 0.09 0.16 4.90 4.30 5.00 4.40 6.4 BSC 5.10 4.50 Note 5 Symbol 1 L1 aaa bbb ccc ddd e 2 3 Variations 3, 8 e 4, 8 N 1, 2 0.65mm Lead Pitch Min Nom Max 0 8 1.0 Ref 0.10 0.10 0.05 0.20 0.65 BSC 12 Ref 12 Ref 0.65 BSC 14 Note 6 Notes: 1. All dimensions are in millimeters; angles in degrees. 2. Dimensions and tolerancing per ASME Y14.5M-1994. 3. Dimension D does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed 0.15mm per side. 4. Dimension E1 does not include interlead flash or protrusion. Interlead flash or protrusion shall not exceed 0.25mm per side. 5. Dimension b does not include dambar protrusion. Allowable dambar protrusion shall be 0.08mm total in excess of dimension b at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07mm for 0.5mm pitch packages. 6. Terminal numbers shown are for reference only. 7. Datums A and B to be determined at datum plane H. 8. Dimensions D and E1 to be determined at datum plane H. 9. This dimension applies only to variations with an even number of leads per side. For variations with an odd number of leads per package, the center lead must be coincident with the package centerline, datum A. 10. Cross section A-A to be determined at 0.10 to 0.25mm from the leadtip. www.austriamicrosystems.com Revision 1.4 14 - 16 austriam i c r o systems AS1751, AS1752, AS1753 Data Sheet 10 Ordering Information The devices are available as the standard products shown in Table 7. Table 7. Ordering Information Part Description Delivery Form Package AS1751S SPST Switch Tube 14-TSSOP AS1751S-T Quad SPST Switch Tape and Reel 14-TSSOP Quad SPST Switch Tray 16-QFN 3mmx3mm Quad SPST Switch Tape and Reel 16-QFN 3mmx3mm AS1752S Quad SPST Switch Tube 14-TSSOP AS1752S-T Quad SPST Switch Tape and Reel 14-TSSOP Quad SPST Switch Tray 16-QFN 3mmx3mm Quad SPST Switch Tape and Reel 16-QFN 3mmx3mm AS1753S Quad SPST Switch Tube 14-TSSOP AS1753S-T Quad SPST Switch Tape and Reel 14-TSSOP Quad SPST Switch Tray 16-QFN 3mmx3mm Quad SPST Switch Tape and Reel 16-QFN 3mmx3mm AS1751V AS1751V-T AS1752V AS1752V-T AS1753V AS1753V-T Future Product www.austriamicrosystems.com Revision 1.4 15 - 16 austriam i c r o systems AS1751, AS1752, AS1753 Data Sheet Copyrights Copyright (c) 1997-2005, austriamicrosystems AG, Schloss Premstaetten, 8141 Unterpremstaetten, Austria-Europe. Trademarks Registered (R). All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. All products and companies mentioned are trademarks or registered trademarks of their respective companies. Disclaimer Devices sold by austriamicrosystems AG are covered by the warranty and patent indemnification provisions appearing in its Term of Sale. austriamicrosystems AG makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. austriamicrosystems AG reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with austriamicrosystems AG for current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or lifesustaining equipment are specifically not recommended without additional processing by austriamicrosystems AG for each application. The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However, austriamicrosystems AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of austriamicrosystems AG rendering of technical or other services. Contact Information Headquarters austriamicrosystems AG A-8141 Schloss Premstaetten, Austria Tel: +43 (0) 3136 500 0 Fax: +43 (0) 3136 525 01 e-mail: info@austriamicrosystems.com For Sales Offices, Distributors and Representatives, please visit: http://www.austriamicrosystems.com austriamicrosystems www.austriamicrosystems.com Revision 1.4 - a leap ahead 16 - 16