AS1753 - austriamicrosystems AG

AS1751, AS1752, AS1753

High-Speed, Low-Voltage, Single-Supply,

0.9Ω, Quad SPST Analog Switches

www.austriamicrosystems.com Revision 1.4 1 - 16

austria

micro

systems

Data Sheet

1 General Description

The AS1751/AS1752/AS1753 are high-speed, low-volt-

age, quad single-pole/single-throw (SPST) analog

switches.

Fast switching speeds, low ON-resistance, and low

power consumption make these devices ideal for single-

cell battery powered applications.

These highly-reliable devices operate from a single +1.6

to +3.6V supply, and are differentiated by the type and

number of switches:

! AS1751 – Four normally open (NO) switches

! AS1752 – Four normally closed (NC) switches

! AS1753 – Two NO switches and Two NC switches

The AS1753 supports break-before-make switching.

With very low ON-resistance (RON), RON matching and

RON flatness, the devices can accurately switch signals

for sample and hold circuits, digital filters, and op-amp

gain switching networks.

The AS1751/AS1752/AS1753 digital logic input is 1.8V

CMOS-compatible when using a +3V supply, and all

devices can handle Rail-to-Rail signals.

The devices are available in a 3mm x 3mm 16-pin QFN

package and a 14-pin TSSOP package.

Figure 1. 14-pin TSSOP Block Diagrams

2 Key Features

! ON-Resistance:

-0.9Ω (+3V supply)

-2.5Ω (+1.8V supply)

! RON Matching:

-0.12Ω (+3V supply)

-0.25Ω (+1.8V supply)

! RON Flatness: 0.1Ω (+3V Supply)

! Supply Voltage Range: +1.6 to +3.6V

! Switching Speed: tON = 22ns, tOFF = 14ns

! Current-Handling: 250mA Continuous

! Break-Before-Make Switching (AS1753)

! Rail-to-Rail Signal Handling

! 1.8V CMOS Logic Compatible (+3V Supply)

! Operating Temperature Range: -40 to +85ºC

! Package Types:

- 16-pin QFN (3mm x 3mm)

- 14-pin TSSOP

3 Applications

The devices are ideal for use in power routing systems,

cordless and mobile phones, MP3 players, CD and DVD

players, PDAs, handheld computers, digital cameras,

hard drives, and any other application where high-speed

signal switching is required.

AS1752

NC1

COM1

NC2

COM2

IN2

IN3

GND

V+

IN1

IN4

NC4

COM4

COM3

NC3

AS1753

NO1

COM1

NC2

COM2

IN2

IN3

GND

V+

IN1

IN4

NC4

COM4

COM3

NO3

AS1751

NO1

COM1

NO2

COM2

IN2

IN3

GND

V+

IN1

IN4

NO4

COM4

COM3

NO3

Device Input Switch State

AS1751 Low Off

High On

AS1752 Low On

High Off

AS1753 Low Switches 1, 3 = Off Switches 2, 4 = On

High Switches 1, 3 = On Switches 2, 4 = Off

AS1751, AS1752, AS1753 austria

micro

systems

Data Sheet

www.austriamicrosystems.com Revision 1.4 2 - 16

4 Absolute Maximum Ratings

Stresses beyond those listed in Table 1 may cause permanent damage to the device. These are stress ratings only,

and functional operation of the device at these or any other conditions beyond those indicated in Section 5 Electrical

Characteristics on page 3 is not implied. Exposure to absolute maximum rating conditions for extended periods may

affect device reliability.

† Signals on pins COM1, COM3, NO1, NO2, NC1, or NC2 that exceed V+ or GND are clamped by internal diodes. For-

ward-diode current should be limited to the maximum current rating.

Table 1. Absolute Maximum Ratings

Parameter Min Max Units Comments

V+, INx to GND -0.3 +5 V

COMx, NOx, NCx to GND †-0.3 V+

+ 0.3 V

COMx, NOx, NCx Continuous Current -250 +250 mA

COMx, NOx, NCx Peak Current -350 +350 mA Pulsed at 1ms 10% duty cycle

Continuous Power

Dissipation (TAMB = +70ºC)

16-pin QFN 727 mW Derate at 9.1W/ºC above +70ºC

14-pin TSSOP 1349 Derate at 16.9W/ºC above +70ºC

Operating Temperature Range -40 +85 ºC

Electro-Static Discharge 2500 V HBM Mil-Std883E 3015.7 methods

Latch Up Immunity 250 mA Norm: JEDEC 17

Junction Temperature +150 ºC

Storage Temperature Range -65 +150 ºC

Package Body Temperature +260 ºC

The reflow peak soldering temperature (body

temperature) specified is in accordance with

IPC/JEDEC J-STD-020C “Moisture/Reflow

Sensitivity Classification for Non-Hermetic

Solid State Surface Mount Devices”

AS1751, AS1752, AS1753 austria

micro

systems

Data Sheet

www.austriamicrosystems.com Revision 1.4 3 - 16

5 Electrical Characteristics

V+ = +2.7 to +3.6V, VIH = +1.4V, VIL = +0.5V, TAMB = TMIN to TMAX (unless otherwise specified). Typ values @ V+ =

+3.0V, TAMB = +25ºC.

Table 2. Power Supply Characteristics

Symbol Parameter Conditions Min Typ Max Unit

V+ Power Supply Range TAMB = TMIN to TMAX 1.6 3.6 V

I+ Positive Supply

Current V+ = 3.6V, VINx = 0 or V+, TAMB = +25ºC 0.1 µA

Table 3. +3V Supply Electrical Characteristics

Symbol Parameter Conditions Min Typ Max Unit

Analog Switch

VCOMx,

VNOx, VNCxAnalog Signal Range 0 V+ V

RON ON-Resistance V+ = 2.7V, ICOMx = 100mA,

VNOx or VNCx = 1.5V

TAMB = +25ºC 0.4 0.9

TAMB = TMIN to TMAX 1

ΔRON ON-Resistance Match

Between Channels 1V+ = 2.7V, ICOMx = 100mA,

VNOx or VNCx = 1.5V

TAMB = +25ºC 0.03 0.12

TAMB = TMIN to TMAX 0.15

RFLAT(ON) ON-Resistance

Flatness 2V+ = 2.7V, ICOMx = 100mA,

VNOx or VNCx = 1, 1.5, or 2V

TAMB = +25ºC 0.02 0.1

TAMB = TMIN to TMAX 0.12

INOx(OFF),

INCx(OFF)

NOx or NCx

Off-Leakage Current

V+ = 3.6V,

VCOMx = 0.3 or 3.6V,

VNOx or VNCx = 3.6 or 0.3V

TAMB = +25ºC -2.5 +2.5 nA

TAMB = TMIN to TMAX -10 +10

ICOMx(OFF) COMx Off-Leakage

Current

V+ = 3.6V,

VCOMx = 0.3 or 3.6V,

VNOx or VNCx = 3.6 or 0.3V

TAMB = +25ºC -2.5 +2.5 nA

TAMB = TMIN to TMAX -10 +10

ICOMx(ON) COMx On-Leakage

Current

V+ = 3.6V,

VCOMx = 0.3 or 3.6V,

VNOx or VNCx = 0.3 or 3.6V

TAMB = +25ºC -2.5 +2.5 nA

TAMB = TMIN to TMAX -10 +10

Switch Dynamic Characteristics

tON Turn On Time 3VNOx or VNCx = 1.5V,

RLOAD = 50Ω, CLOAD =

35pF, Figures 11, 12

TAMB = +25ºC 16 22 ns

TAMB = TMIN to TMAX 24

tOFF Turn Off Time 3VNOx or VNCx = 1.5V,

RLOAD = 50Ω, CLOAD =

35pF, Figures 11, 12

TAMB = +25ºC 5 14 ns

TAMB = TMIN to TMAX 15

tBBM Break-Before-Make 3VNOx or VNCx = 1.5V,

RLOAD = 50Ω, CLOAD =

35pF, Figure 13 (AS1753)

TAMB = +25ºC 11 ns

TAMB = TMIN to TMAX 2

QCharge Injection VGEN = V+, RGEN = 0, CLOAD = 1.0nF, Figure 14 2 pC

COFF NOx, NCx

Off-Capacitance f = 1MHz, Figure 15 45 pF

CCOMx(OFF) COMx

Off-Capacitance f = 1MHz, Figure 15 49 pF

CCOMx(ON) COMx

On-Capacitance f = 1MHz, Figure 15 85 pF

AS1751, AS1752, AS1753 austria

micro

systems

Data Sheet

www.austriamicrosystems.com Revision 1.4 4 - 16

V+ = +1.8V, VIH = +1.0V, VIL = 0.4V, TAMB = TMIN to TMAX (unless otherwise specified). Typ values @ TAMB = +25ºC.

1. ΔRON = RON(MAX) - RON(MIN).

2. Flatness is defined as the difference between the maximum and the minimum value of ON-resistance as measured

over the specified analog signal ranges.

3. Guaranteed by design.

4. Off-Isolation = 20log10(VCOMx/VNOx), VCOMx = output, VNOx = input to off switch.

5. Between two switches.

VISO Off-Isolation 4f = 10MHz, RLOAD = 50Ω, CLOAD = 5pF, Figure 16 -40 dB

f = 1MHz, RLOAD = 50Ω, CLOAD = 5pF, Figure 16 -55

Crosstalk 5f = 10MHz, RLOAD = 50Ω, CLOAD = 5pF, Figure 16 -70 dB

f = 1MHz, RLOAD = 50Ω, CLOAD = 5pF, Figure 16 -80

THD Total Harmonic

Distortion f = 20Hz to 20kHz, VCOMx = 2Vp-p, RLOAD = 32Ω0.033 %

Logic Input

VIH Input Logic High 1.4 V

VIL Input Logic Low 0.5 V

IIN Input Leakage Current VINx = 0 or V+ -1 0.0001 +1 µA

Table 4. +1.8V Supply Electrical Characteristics

Symbol Parameter Conditions Min Typ Max Unit

Analog Switch

VCOMx,

VNOx, VNCx

Analog Signal

Range 0V+V

RON ON-Resistance V+ = 1.8V, ICOMx = 10mA,

VNOx or VNCx = 0.9V

TAMB = +25ºC 0.9 2.5 Ω

TAMB = TMIN to TMAX 3

ΔRON

ON-Resistance

Match Between

Channels 1

V+ = 1.8V, ICOMx = 10mA,

VNOx or VNCx = 0.9V

TAMB = +25ºC 0.05 0.25

TAMB = TMIN to TMAX 0.25

Switch Dynamic Characteristics

tON Turn On Time 3VNOx or VNCx = 1.0V,

RLOAD = 50Ω, CLOAD = 35pF,

Figures 11, 12

TAMB = +25ºC 22 30 ns

TAMB = TMIN to TMAX 35

tOFF Turn Off Time 3VNOx or VNCx = 1.0V,

RLOAD = 50Ω, CLOAD = 35pF,

Figures 11, 12

TAMB = +25ºC 12 20 ns

TAMB = TMIN to TMAX 25

QCharge Injection VGEN = V+, RGEN = 0, CLOAD = 1.0nF, Figure 14 1 pC

Logic Input

VIH Input Logic High 1.0 V

VIL Input Logic Low 0.4 V

IIN Input Leakage

Current VINx = 0 or V+ -1 0.0001 +1 µA

Table 3. +3V Supply Electrical Characteristics (Continued)

Symbol Parameter Conditions Min Typ Max Unit

AS1751, AS1752, AS1753 austria

micro

systems

Data Sheet

www.austriamicrosystems.com Revision 1.4 5 - 16

6 Typical Operating Characteristics

Figure 2. Frequency Response Figure 3. Total Harmonic Distortion vs. Frequency

Figure 4. Turn On/Turn Off Time vs. Temperature Figure 5. Turn On/Off Time vs. Supply Voltage

Figure 6. RON vs. VCOM and Temperature; VDD = 2.7V Figure 7. RON vs. VCOM

-100

-90

-80

-70

-60

-50

-40

-30

-20

-10

0.01 0.1 1 10 100 1000

Frequency (MHz)

Response (dB)

Bandwidth

0.005

0.01

0.015

0.02

0.025

0.03

0.035

0.04

1 10 100 1000 10000 100000

Frequency (Hz)

THD (%)

VDD = 3V

1.6 2 2.4 2.8 3.2 3.6

Supply Voltage (V)

Time (ns)

tON

tOFF

-40 -15 10 35 60 85

Temperature (°C)

Time (ns)

tON

tOFF

0.20

0.25

0.30

0.35

0.40

0.45

0.50

0 0.5 1 1.5 2 2.5 3

VCOM (V)

RON (Ω)

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

0 0.5 1 1.5 2 2.5 3 3.5

VCOM (V)

RON (Ω)

Temp = -40ºC

VDD = 1.8V

VDD = 2.5V

VDD = 2.7V

VDD = 3V

VDD = 3.6V

VDD = 2V

VDD = 3.3V

Temp = +25ºC

Temp = +85ºC

AS1751, AS1752, AS1753 austria

micro

systems

Data Sheet

www.austriamicrosystems.com Revision 1.4 6 - 16

Figure 8. Charge Injection vs. VCOM

0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3

VCOM (V)

Q (pC)

VDD = 1.8V

VDD = 3V

AS1751, AS1752, AS1753 austria

micro

systems

Data Sheet ON-Resistance

www.austriamicrosystems.com Revision 1.4 7 - 16

7 Detailed Description

The AS1751/AS1752/AS1753 are low ON-resistance, low-voltage, quad analog SPST switches that operate from a

single +1.6 to +3.6V supply.

CMOS process technology allows switching of analog signals that are within the supply voltage range (GND to V+).

Figure 9. 16-pin QFN Block Diagrams

ON-Resistance

When powered from a +3V supply, the low (0.9Ω, max) ON-resistance allows high-speed, continuous signals to be

switched in a variety of applications.

Bi-Directional Switching

Pins NOx, NCx, and COMx are bi-directional, thus they can be used as inputs to- or outputs from other components.

Analog Signal Levels

Analog signals ranging over the entire supply voltage range (V+ to GND) can be switched with very little change in ON-

resistance (see Typical Operating Characteristics on page 5).

Logic Inputs

The devices’ logic inputs can be driven up to +3.6V regardless of the supply voltage value. For example, with a +1.8V

supply, INx may be driven low to GND and high to +3.6V. This allows the devices to interface with +3V systems using

a supply of less than 3V.

Table 5. Truth Tables

Device Input Switch State

AS1751 Low Off

High On

AS1752 Low On

High Off

AS1753 Low Switches 1, 3 = Off Switches 2, 4 = On

High Switches 1, 3 = On Switches 2, 4 = Off

AS1751

COM2

N/C

IN2

NO2

GND

COM3

IN3

NO3

NO4

N/C

COM4

IN4

COM1

AS1752

COM2

N/C

IN2

NC2

GND

COM3

IN3

NC3

NC4

N/C

COM4

IN4

AS1753

COM2

N/C

IN2

NC2

GND

COM3

IN3

NO3

NC4

N/C

COM4

IN4

NO1

V+

IN1

COM1

NC1

V+

IN1

COM1

NO1

V+

IN1

AS1751, AS1752, AS1753 austria

micro

systems

Data Sheet Power Supply Sequencing

www.austriamicrosystems.com Revision 1.4 8 - 16

8 Application Information

Power Supply Sequencing

Proper power-supply sequencing is critical for proper switch operation. The power supplies should be started up in the

following sequence:

1. V+

2. NOx, NCx, COMx

Note: Do not exceed the absolute maximum ratings (see page 2).

Overvoltage Protection

ON-resistance increases slightly at lower supply voltages.

Figure 10. Overvoltage Protection using 2 External Blocking Diodes

Adding diode D2 to the circuit shown in Figure 10 causes the logic threshold to be shifted relative to GND. Diodes D1

and D2 also protect against overvoltage conditions.

For example, in the circuit shown in Figure 10, if the supply voltage goes below the absolute maximum rating, and if a

fault voltage up to the absolute maximum rating is applied to an analog signal pin, no damage will result.

Power Supply Bypass

Power supply connections to the devices must maintain a low impedance to ground. This can be done using a bypass

capacitor, which will also improve noise margin and prevent switching noise propagation from the V+ supply to other

components.

A 0.1µF bypass capacitor, connected from V+ to GND (see Figure 16 on page 10), is adequate for most applications.

Logic Inputs

Driving INx Rail-to-Rail will help minimize power consumption.

Layout Considerations

High-speed switches require proper layout and design procedures for optimum performance.

! Short, wide traces should be used to reduce stray inductance and capacitance.

! Bypass capacitors should be as close to the device as possible.

! Large ground planes should be used wherever possible.

AS1751/AS1752/AS1753

GND

VGEN

COMx

D1 V+

V+

NOx

AS1751, AS1752, AS1753 austria

micro

systems

Data Sheet Timing Diagrams and Test Setups

www.austriamicrosystems.com Revision 1.4 9 - 16

Timing Diagrams and Test Setups

Figure 11. AS1751/AS1753 Test Circuit and Timing Diagram

Figure 12. AS1752/AS1753 Test Circuit and Timing Diagram

Figure 13. AS1753 Test Circuit and Timing Diagram

Figure 14. Charge Injection

AS1751/

AS1753

COMx

NOx

35pF50Ω

VCOMx

INx

VNOx

50Ω

V+

GND

VCOMx

INx

VNOx

VIH + 0.5V

tON tOFF

tR < 5ns

tF < 5ns

50% 50%

90%90%

AS1752/

AS1753

COMx

NCx

35pF50Ω

VCOMx

INx

VNCx

50Ω

V+

VCOMx

INx

VNCx

VIH + 0.5V

tOFF tON

50% 50%

90%90%

GND

tR < 5ns

tF < 5ns

AS1753

COM2

NO1

35pF50Ω

VCOMx

NC2

INx

VSVS

50Ω

V+

VCOMx

INx

VIH + 0.5V

tBBM

90%

tBBM

90%

tBBM = tON(NOx) - tOFF(NCx)

or tBBM = tON(NCx) - tOFF(NOx)

GND

tR < 5ns

tF < 5ns

COM1

AS175x

COMx

NCx

NOx

CLOAD

1000pF

VOUT

INx

VGEN

50Ω

V+

V+ VIN

V+

ΔVOUTVOUT

AS1751 AS1752

ΔVOUT is the measured voltage due to charge transfer error Q

when the channel turns off.

Q = ΔVOUT x CLOAD

GND

RGEN

VIN

AS1751, AS1752, AS1753 austria

micro

systems

Data Sheet Timing Diagrams and Test Setups

www.austriamicrosystems.com Revision 1.4 10 - 16

Figure 15. NOx, NCx, and COMx Capacitance

Figure 16. Off-Isolation, On-Loss, and Crosstalk

Notes:

1. Measurements are standardized against short-circuit at socket terminals.

2. Off-isolation is measured between COMx and the off NCx/NOx terminal on each switch. Off-isolation = 20log (VOUT/

VIN).

3. On-loss is measured between COMx and the on NCx/NOx terminal on each switch. On-loss = 20log (VOUT/VIN).

4. Signal direction through the switch is reversed; worst values are recorded.

AS1751/

AS1752/

AS1753

COMx

NCx or

NOx

INx

V+

Required

GND

1MHz

Capacitance

Analyzer

AS1751/

AS1752/

AS1753

COMx

NOx

NCx

INx

V+

50Ω50Ω

VIN

VOUT

0.1µF

Measure Reference

GND

Network Analyzer

† Use 50Ω termina-

tion for off-isolation

†

AS1751, AS1752, AS1753 austria

micro

systems

Data Sheet Pin Assignments

www.austriamicrosystems.com Revision 1.4 11 - 16

9 Pinout and Packaging

Pin Assignments

Figure 17. QFN Pin Assignments (Top View)

Figure 18. TSSOP Pin Assignments (Top View)

Pin Descriptions

Table 6. Pin Descriptions

Pin Number Pin Name Description

(see Figure 17

and Figure 18)

COM1: COM4 Analog Switch 1, 2, 3, 4 Common

GND Ground

IN1:IN4 Analog Switch 1, 2, 3, 4 Logic Control Input

NC1:NC4 Analog Switch 1, 2, 3, 4 Normally Closed Terminal

NO1:NO4 Analog Switch 1, 2, 3, 4 Normally Open Terminal

V+ Input Supply Voltage, +1.6 to +3.6V

15 NO1

AS1753

16 COM1

14 V+

13 IN1

11 NC4

12 IN4

10 –

9COM4

GND

IN3

NO3

COM3

COM2

NC2

–

IN2

15 NC1

AS1752

16 COM1

14 V+

13 IN1

11 NC4

12 IN4

10 –

9COM4

GND

IN3

NC3

COM3

COM2

NC2

–

IN2

15 NO1

AS1751

16 COM1

14 V+

13 IN1

11 NO4

12 IN4

10 –

9COM4

GND

IN3

NO3

COM3

COM2

NO2

–

IN2

AS1751

14 V+

8NO3

9COM3

12 IN4

NO1

GND

IN3

NO2

11 NO4

COM2

10 COM4

IN2

13 IN1

COM1

AS1752

14 V+

8NC3

9COM3

12 IN4

NC1

GND

IN3

NC2

11 NC4

COM2

10 COM4

IN2

13 IN1

COM1

AS1753

14 V+

8NO3

9COM3

12 IN4

NO1

GND

IN3

NC2

11 NC4

COM2

10 COM4

IN2

13 IN1

COM1

AS1751, AS1752, AS1753 austria

micro

systems

Data Sheet Package Drawings and Markings

www.austriamicrosystems.com Revision 1.4 12 - 16

Package Drawings and Markings

The devices are available in an 16-pin QFN package and an 14-pin TSSOP package.

Figure 19. 16-pin QFN Package

-C-

SIDE VIEW PLANE

ccc C

0.08 C

11 NX SEATING

D/2

INDEX AREA

aaa C

TOP VIEW

(D/2 xE/2)

E/2

-B-

-A-

NXL

NXb

D2/2

E2/2

bbb C A B

ddd C

-B-

-A-

NN-1

BTM VIEW

(D/2 xE/2)

INDEX AREA

SEE

DETAIL B

SEE

DETAIL B

Datum A or B

EVEN TERMINAL SIDE

DETAIL B

Terminal Tip

e/2

Common Dimensions

Symbol Min Nom Max Notes

aaa 0.15 1, 2

bbb 0.10 1, 2

ccc 0.10 1, 2

ddd 0.05 1, 2

A 0.70 0.75 0.80

A1 0.00 0.02 0.05

A3 0.20

Ref

L1 0.03 0.15

D BSC 3.00 1, 2, 10

E BSC 3.00 1, 2, 10

D2 1.30 1.45 1.55 1, 2, 10

E2 1.30 1.45 1.55 1, 2, 10

L 0.30 0.40 0.50 1, 2, 10

N 16 1, 2, 10

ND 4 1, 2, 10

NE 4 1, 2, 10

PIN 1

MARKER

AS1751, AS1752, AS1753 austria

micro

systems

Data Sheet Package Drawings and Markings

www.austriamicrosystems.com Revision 1.4 13 - 16

Notes:

1. Dimensioning and tolerancing conform to ASME Y14.5M-1994.

2. All dimensions are in millimeters; angles in degrees.

3. N is the total number of terminals.

4. The terminal #1 identifier and terminal numbering convention shall conform to JEDEC 95 SPP-012. Details of termi-

nal #1 identifier are optional but must be located within the zone indicated. The terminal #1 identifier may be either

a mold or marked feature.

5. Dimension b applies to metallized terminal and is measured between 0.15 and 0.30mm from terminal tip. If one end

of the terminal has the optional radius, the b dimension should not be measured in that radius area.

6. Dimensions ND and NE refer to the number of terminals on each D and E side, respectively.

7. Depopulation is possible in a symmetrical fashion.

8. Figure 19 is shown for illustration only and does not represent any specific variation.

9. All variations may be constructed per Figure 19, however variations may alternately be constructed between square

or rectangle shape per dimensions D and E.

10. Refer to the Dimensions Table for a complete set of dimensions.

11. Bilateral coplanarity zone applies to the exposed heat sink slug as well as the terminals.

12. Depending on the method of lead termination at the edge of the package, pullback (L1) may be present. L minus

L1 to be ≥ 0.33mm.

13. For variations with more than one lead count for a given body size and terminal pitch, each lead count for that vari-

ation is denoted by a dash number (e.g., -1 or -2).

14. NJR designates non-JEDEC registered package.

AS1751, AS1752, AS1753 austria

micro

systems

Data Sheet Package Drawings and Markings

www.austriamicrosystems.com Revision 1.4 14 - 16

Figure 20. 14-pin TSSOP Package

Notes:

1. All dimensions are in millimeters; angles in degrees.

2. Dimensions and tolerancing per ASME Y14.5M-1994.

3. Dimension D does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not

exceed 0.15mm per side.

4. Dimension E1 does not include interlead flash or protrusion. Interlead flash or protrusion shall not exceed 0.25mm

per side.

5. Dimension b does not include dambar protrusion. Allowable dambar protrusion shall be 0.08mm total in excess of

dimension b at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum

space between protrusion and adjacent lead is 0.07mm for 0.5mm pitch packages.

6. Terminal numbers shown are for reference only.

7. Datums A and B to be determined at datum plane H.

8. Dimensions D and E1 to be determined at datum plane H.

9. This dimension applies only to variations with an even number of leads per side. For variations with an odd number

of leads per package, the center lead must be coincident with the package centerline, datum A.

10. Cross section A-A to be determined at 0.10 to 0.25mm from the leadtip.

Symbol 0.65mm Lead Pitch 1, 2 Note Symbol 0.65mm Lead Pitch 1, 2 Note

Min Nom Max Min Nom Max

A- -1.10 θ10º - 8º

A1 0.05 - 0.15 L1 1.0 Ref

A2 0.85 0.90 0.95 aaa 0.10

L 0.50 0.60 0.75 bbb 0.10

R 0.09 - - ccc 0.05

R1 0.09 - - ddd 0.20

b 0.19 - 0.30 5 e 0.65 BSC

b1 0.19 0.22 0.25 θ2 12º Ref

c 0.09 - 0.20 θ3 12º Ref

c1 0.09 - 0.16

Variations

D 4.90 5.00 5.10 3, 8 e 0.65 BSC

E1 4.30 4.40 4.50 4, 8 N 14 6

E 6.4 BSC

AS1751, AS1752, AS1753 austria

micro

systems

Data Sheet

www.austriamicrosystems.com Revision 1.4 15 - 16

10 Ordering Information

The devices are available as the standard products shown in Table 7.

† Future Product

Table 7. Ordering Information

Part Description Delivery Form Package

AS1751S SPST Switch Tube 14-TSSOP

AS1751S-T Quad SPST Switch Tape and Reel 14-TSSOP

AS1751V †Quad SPST Switch Tray 16-QFN 3mmx3mm

AS1751V-T †Quad SPST Switch Tape and Reel 16-QFN 3mmx3mm

AS1752S Quad SPST Switch Tube 14-TSSOP

AS1752S-T Quad SPST Switch Tape and Reel 14-TSSOP

AS1752V †Quad SPST Switch Tray 16-QFN 3mmx3mm

AS1752V-T †Quad SPST Switch Tape and Reel 16-QFN 3mmx3mm

AS1753S Quad SPST Switch Tube 14-TSSOP

AS1753S-T Quad SPST Switch Tape and Reel 14-TSSOP

AS1753V †Quad SPST Switch Tray 16-QFN 3mmx3mm

AS1753V-T †Quad SPST Switch Tape and Reel 16-QFN 3mmx3mm

AS1751, AS1752, AS1753 austria

micro

systems

Data Sheet

www.austriamicrosystems.com Revision 1.4 16 - 16

Copyrights

lated, stored, or used without the prior written consent of the copyright owner.

All products and companies mentioned are trademarks or registered trademarks of their respective companies.

Disclaimer

Devices sold by austriamicrosystems AG are covered by the warranty and patent indemnification provisions appearing

in its Term of Sale. austriamicrosystems AG makes no warranty, express, statutory, implied, or by description regarding

the information set forth herein or regarding the freedom of the described devices from patent infringement. austriami-

crosystems AG reserves the right to change specifications and prices at any time and without notice. Therefore, prior

to designing this product into a system, it is necessary to check with austriamicrosystems AG for current information.

This product is intended for use in normal commercial applications. Applications requiring extended temperature

range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-

sustaining equipment are specifically not recommended without additional processing by austriamicrosystems AG for

each application.

The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However,

austriamicrosystems AG shall not be liable to recipient or any third party for any damages, including but not limited to

personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or

consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the tech-

nical data herein. No obligation or liability to recipient or any third party shall arise or flow out of

austriamicrosystems AG rendering of technical or other services.

Contact Information

Headquarters

austriamicrosystems AG

A-8141 Schloss Premstaetten, Austria

Tel: +43 (0) 3136 500 0

Fax: +43 (0) 3136 525 01

e-mail: info@austriamicrosystems.com

For Sales Offices, Distributors and Representatives, please visit:

http://www.austriamicrosystems.com

austria

micro

systems

– a leap ahead