TD62930PG/FG
2006-01-20
1
TOSHIBA BIPOLAR DIGITAL IC SILICON MONOLITHIC
TD62930PG,TD62930FG
THREE−CHANNEL SMALL−SIGNAL IGBT GATE DRIVER
The TD62930PG and TD62930FG are drivers using 5 V−signal
input to output the signals required to drive IGBT gates.
TD62930PG / FG is the most suitable for low−side drive of a
miniature IGBT to use for inverter for the household electric
appliances mainly.
The outputs are separated into high−side and low−side outputs.
This separation simplifies the IGBT gate on / off timing control.
Two output signals are assigned for one input signal.
The high−side output is high−level for high−level input, and high
impedance for low−level input. The low−side output is high
impedance for high−level input, and low−level for low−level
input.
The suffix (G) appended to the part number represents a Lead
(Pb)-Free product.
Features
Power supply voltage (absolute maximum rating)
High−voltage block power supply voltage VCC = 30 V
Low−voltage block power supply voltage VDD = 7 V
Output current (absolute maximum rating)
High−side peak current IOUT = −0.4 A (max)
Low−side peak current IOUT = 0.4 A (max)
Input−output response speed tpHL, tpLH ≤ 1 µs (max)
Package : DIP16 / SSOP16 (1.00 mm pitch)
TD62930PG
TD62930FG
Weight
DIP16-P-300-2.54A : 1.11 g (typ.)
SSOP16-P-225-1.00A : 0.14 g (typ.)
TD62930PG/FG
2006-01-20
2
Pin Assignment (top view)
Internal Equivalent Circuit
Pin Description
PIN No. PIN NAME FUNCTION
1, 8 VCC 30 V supply pins
2 VDD 5 V supply pin
3, 7 L−GND Ground pins for 5 V supply
4, 5, 6 IN1~3 Input pins for 5 V output control signals
11, 14 P−GND Ground pins for 30 V supply
9, 12, 15 OUT−L1~3 Low−side output pins
10, 13, 16 OUT−H1~3 High−side output pins
TD62930PG/FG
2006-01-20
3
Absolute Maximum Ratings (Ta = 25°C)
CHARACTERISTIC PIN / PACKAGE SYMBOL RATING UNIT
Power Supply Voltage VCC VCC 30 V
Power Supply Voltage VDD VDD 7 V
Input Voltage IN1~3 VIN −0.5~VDD + 0.5 V
0~20 (Ta = −20~85°C)
OUT−H1~3 VOUT (H) 0~30 (Ta = −20~70°C)
V
−0.5~20 (Ta = −20~85°C)
Output Voltage
OUT−L1~3 VOUT (L) −0.5~30 (Ta = −20~70°C)
V
High−level Output Peak Current OUT−H1~3 IOPH (Note 1) −0.4 A / ch
Low−level Output Peak Current OUT−L1~3 IOPL (Note 1) +0.4 A / ch
Operating Frequency IN1~3 f 25 kHz
DIP16 PD1 (Note 2) 1.47 (FREE AIR) W
Power Dissipation
SSOP16 PD2 (Note 2) 0.78 (ON PCB) W
Operating Ambient Temperature Topr −20~85 °C
Storage Temperature Tstg −55~150 °C
Note 1: Output pin current
The pulse width of the output pin current at peak is ≤ 1 µs, 300 pps.
Note 2: When ambient temperature exceeds 25°C
Derate the power dissipation of DIP−type devices at 11.76 mW / 1°C (device only) and
Derate the power dissipation of SMD−type devices at 6.24 mW / 1°C (mounted on the board).
Recommended Operating Conditions
(Unless otherwise specified, Ta = −20 to 70°C)
CHARACTERISTIC PIN SYMBOL TEST CONDITION MIN TYP. MAX UNIT
High level VIH 3.5 ― ―
Input Voltage
Low level
IN1~3
VIL
VCC = 15 V,
VDD = 4.5~5.5 V ― ― 1.0
V
High level IIH ― ― 5
Input Current
Low level
IN1~3
IIL
VCC = 15 V,
VDD = 4.5~5.5 V ― ― −5
mA
VCC VCC 10 15 25
Input Power Supply Voltage
VDD VDD 4.5 5.0 5.5
V
IOH (DC) ― ― −0.1
OUT−H1~3
IOH (Peak)
VCC = 20 V, VDD = 4.5 V
― ― −0.35
IOL (DC) ― ― 0.1
Output Current
OUT−L1~3
IOL (Peak)
VCC = 20 V, VDD = 4.5 V
― ― 0.35
A
VCC = 30 V, VDD = 5.5 V −20 25 70
Operating Temperature Topr VCC = 20 V, VDD = 5.5 V −20 25 85
°C
TD62930PG/FG
2006-01-20
4
Electrical Characteristics (Unless otherwise specified, Ta = −20 to 70°C)
CHARACTERISTIC PIN SYMBOL TEST CONDITION MIN TYP. MAX UNIT
High level IIH VCC = 15 V, VIN = 5 V 0.1 0.2 0.4
Input Current
Low level
IN1~3
IIL VCC = 15 V, VIN = 0 V ― 0 ―
mA
High level OUT−H1~3 VOH VCC = 15 V, VIH = 5 V,
RLH = 100 Ω
VCC
−4.0
VCC
−1.9
VCC
−1.0
Output
Voltage
Low level OUT−L1~3 VOL VCC = 15 V, VIL = 0 V,
RLL = 100 Ω 0.3 0.5 2.5
V
VDD = 5.5 V, VIH = 0 V,
Ta = 25°C ― 1.5 3.0
IDDL VDD = 5.5 V, VIH = 0 V,
Ta = −20~85°C ― ― 3.5
VDD = 5.5 V, VIH = 5 V,
Ta = 25°C ― 1.8 3.5
Dissipation Current 1 VDD
IDDH VDD = 5.5 V, VIH = 5 V,
Ta = −20~85°C ― ― 4.0
mA
VCC = 30 V, VDD = 5.5 V,
V
IH = 0 V, Ta = 25°C ― 10.2 15.0
ICCL
VCC = 30 V, VDD = 5.5 V,
VIH = 0 V ― ― 18.0
VCC = 30 V, VDD = 5.5 V,
V
IH = 5 V, Ta = 25°C ― 7.5 11.0
Dissipation Current 2 VCC
ICCH
VCC = 30 V, VDD = 5.5 V,
VIH = 5 V ― ― 14.0
mA
Operating Power Supply Voltage VCC VCCopr 10 ― 30 V
Switching Characteristics (Unless otherwise specified, Ta = −20~70°C)
CHARACTERISTIC PIN SYMBOL TEST CONDITION MIN TYP. MAX UNIT
High level OUT−H1~3 tPLH
VDD = 5.0 V, VCC = 15 V
RLH = RLL = 100 Ω,
VIN = 0.7 to 4 V
― 0.25 1.00
Output
Propagation
Delay Time
Low level OUT−L1~3 tPHL
VDD = 5.0 V, VCC = 15 V
RLH = RLL = 100 Ω,
VIN = 4 to 0.7 V
― 0.25 1.00
µs
TD62930PG/FG
2006-01-20
5
Switching Waveform
Propagation Delay Time Test Circuit
Toshiba recommends connecting load resistors as in the above diagram, utilizing the independence of the
high−level and low−level sides of this IC.
TD62930PG/FG
2006-01-20
6
Test Circuit
(1) IIH (2) IIL
(3) VIH, VOH (4) VIL, VOL
(5) IDDL, IDDH (6) ICCL, ICCH
TD62930PG/FG
2006-01-20
7
Application Circuit
Precautions for Using
This IC does not integrate protection circuits such as overcurrent and overvoltage protectors.
Thus, if excess current or voltage is applied to the IC, the IC may be damaged. Please design the IC so that
excess current or voltage will not be applied to the IC.
Utmost care is necessary in the design of the output line, VCC and GND (L−GND, P−GND) line since IC may be
destroyed due to short−circuit between outputs, air contamination fault, or fault by improper grounding.
TD62930PG, TD62930FG
TD62930PG/FG
2006-01-20
8
Package Dimensions
DIP16−P−300−2.54A Unit: mm
Weight: 1.11 g (Typ.)
TD62930PG/FG
2006-01-20
9
Package Dimensions
SSOP16−P−225−1.00A Unit: mm
Weight: 0.14 g (Typ.)
TD62930PG/FG
2006-01-20
10
Notes on Contents
1. Schematics
The schematics may be simplified or some parts of them may be omitted for explanatory purposes.
2. Absolute Maximum Ratings
The absolute maximum ratings of a semiconductor device are a set of specified parameter values that must
not be exceeded during operation, even for an instant.
If any of these ratings are exceeded during operation, the electrical characteristics of the device may be
irreparably altered and the reliability and lifetime of the device can no longer be guaranteed.
Moreover, any exceeding of the ratings during operation may cause breakdown, damage and/or degradation
in other equipment. Applications using the device should be designed so that no absolute maximum rating
will ever be exceeded under any operating conditions.
Before using, creating and/or producing designs, refer to and comply with the precautions and conditions
set forth in this document.
3. Recommended Operating Conditions
The values of the conditions are applied within the range of the operating temperature and not guaranteed.
4. AC Characteristics
AC characteristics that mean turn-on and turn-off time are targeted design values and not guaranteed.
5. Application Circuits
The application circuits shown in this document are provided for reference purposes only. Thorough
evaluation is required, especially in the phase of mass production design.
In furnishing these examples of application circuits, Toshiba does not grant the use of any industrial
property rights.
Handling of the IC
Ensure that the product is installed correctly to prevent breakdown, damage and/or degradation in the product or
equipment.
TD62930PG/FG
2006-01-20
11
