REVISIONS
LTR DESCRIPTION DATE (YR-MO-DA) APPROVED
A
Changes in accordance with NOR 5962-R139-96.
96-06-06
M. A. FRYE
B
Replaced referenc e to MIL-STD-973 with reference to MIL-PRF-38535.
Deleted subgroups 10 and 11 in table II (not called out in table I). Drawing
updated to reflect current requi rements. -rrp
04-01-27
R. MONNIN
C
Drawing updated to reflect current requirements. –rrp
11-03-08
C. SAFFLE
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV STATUS REV C C C C C C C C C
OF SHE ETS SHEET 1 2 3 4 5 6 7 8 9
PMIC N/A PREPARED BY
Charles E. Besore
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.dscc.dla.mil
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
CHECKED BY
Charles E. Besore
APPRO V ED BY
Michael A. Frye
MICROCIRCUI T, LINEAR, VOLTAGE
COMPARATOR, QUAD, PRECISION,
MONOLITHIC SILICON
DRAWING APPROVAL DATE
90-02-02
AMSC N/A
REVISION LEVEL
C SIZE
A CAGE CODE
67268
5962-86860
SHEET 1 OF 9
DSCC FORM 2233
APR 97 5962-E028-11
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-86860
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
C SHEET 2
DSCC FORM 2234
APR 97
1. SCOPE
1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
5962-86860
01
E
A
Drawing number
Device type
(see 1.2.1)
Case outline
(see 1.2.2)
Lead finish
(see 1.2.3)
1.2.1 Dev ice ty pe(s). The device type(s) identify the circuit function as follows:
Device type Generic number Circuit function
01 HA-4902 Precision qua d comp arat or
1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter Descriptive designator Terminals Pa cka ge sty l e
E GDIP1-T16 or CDIP 2-T16 16 Dual-in-line
2 CQCC1-N20 20 Square leadless chi p carri er
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
1.3 Absol ute maximum rating s.
Voltage between +V and –V termin als ...................................................................... 33 V dc
Differential input voltage ............................................................................................ ±15 V dc
Output short-circuit duration ...................................................................................... Indefinite 1/
Peak output current ................................................................................................... ±50 mA
Storage temperature range ....................................................................................... -65°C to +150°C
Maximum power dissipation (PD):
Case E ................................................................................................................... 1.33 W 2/
Case 2 ................................................................................................................... 1.32 W 3/
Lead temperature (soldering, 10 seconds) ................................................................ +275°C
Thermal resistance, junction-to-case (θJC) ................................................................ See MIL-STD-1835
Thermal resistance, junction-to-ambient (θJA):
Case E ................................................................................................................... 75°C/W
Case 2 ................................................................................................................... 76°C/W
Junction temperature (TJ) .......................................................................................... +175°C
1.4 Recom mended operating cond itio ns.
Positive supply voltage (+V) ...................................................................................... +15 V dc
Negative supply voltage (-V) ..................................................................................... -15 V dc
Logic supply voltage (+VL) ........................................................................................ +5.0 V dc
Logic reference voltage (-VL) ..................................................................................... 0 V dc
Ambient temperature range (TA) ............................................................................... -55°C to +125°C
1/ One amplifier shorted to gr ound.
2/ Derate linearly above TA = +75°C at 13.4 mW/°C.
3/ Derate linearly above TA = +75°C at 13.1 mW/°C.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-86860
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
C SHEET 3
DSCC FORM 2234
APR 97
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks for m a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitati on or contr ac t.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated C ircuit s, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of prece den ce. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-
JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer
Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certificat ion to M IL-
PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying
activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan
may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.
These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-
PRF-38535 is required to identify when the QML flow option is used.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535, appendix A and herein.
3.2.1 Case outline. The case outline shall be in accordance with 1.2.2 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.3 Electr ica l performance char act eris tic s. Unless otherwise specified herein, the electrical performance character ist ic s are
as specified in table I and shall apply over the full ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in table I.
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN
listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entir e SM D
PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device.
3.5.1 Certificati on/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices bui lt in compliance
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-86860
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
C SHEET 4
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics.
Test Symbol Conditions 1/
-55°C ≤ TA ≤ +125°C
unless otherw ise speci fied
Group A
subgroups
Device
type
Limits Unit
Min
Max
Input offset volt age
VIO VCM = 0 V, VOUT = 1.4 V 2/ 1 01 ±5.0 mV
2, 3 ±8.0
Input bias current
+I
B
V
CM
= 0 V
1
01
±150
nA
2, 3
±200
-IB 1 ±150
2, 3
±200
Input offset current
I
IO
V
CM
= 0 V
1
01
±35
nA
2, 3 ±45
Input sensitiv ity
IN
SEN
V
CM
= 0 V
1
01
±0.5
mV
2, 3
±0.6
Output low voltage VOL ISINK = 3.0 mA 1, 2, 3 01 0.4 V
Output high voltage VOH ISOURCE = 3.0 mA 1, 2, 3 01 3.5 V
Output sink current ISINK VOUT ≤ 0.4 V 1, 2, 3 01 3.0 mA
Output sour ce curren t
I
SOURCE
VOUT ≥ 0.4 V
1, 2, 3
01
-3.0
mA
Supply current
+I
CC
V
OUT
= V
OL
and V
OH
1, 2, 3
01
20
mA
-I
CC
1
8.0
2, 3
10
Logic current
I
L
V
OUT
= V
OL
and V
OH
1
01
6.0
mA
2, 3
8.0
Response time 3/
t
PD0
100 mV input step, 4/
10 mV overdrive,
TA = +25°C
9
01
200
ns
t
PD1
-100 mV input step, 4/
-10 mV overdrive,
TA = +25°C
9
200
Common mode voltage
range 3/
+V
CM
TA = +25°C
1
01
-15
12.4
V
-V
CM
-15
12.4
1/ +V = 15 V, -V = -15 V, and VL = 0 V unless otherwise specified herein.
2/ Offset voltage is measured when VOUT = 1.4 V. Sensitivity is measured on the transition edge at 0.4 V and 3.5 V.
Sensitivity is the change in differential input voltage required to change the output state. Sensitivity includes the effects of
of fse t v ol tage and voltage gain. See figure 2.
3/ If not tested, shall be guaranteed to the limits specified in table I.
4/ Duty cycle = 50%, f = 100 Hz, inverting input is driven, and all unused inverting inputs are tied to +5.0 V. See figure 3.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-86860
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
C SHEET 5
DSCC FORM 2234
APR 97
Device type
01
Case outlines
E
2
Terminal number
Terminal symbo l
1
+VL
NC
2
OUT 1
+VL
3
-IN
OUT 1
4
+IN
-IN 1
5
-V
+IN 1
6
+IN 2
NC
7
-IN 2
-V
8
OUT 2
+IN 2
9
-VL
-IN 2
10
OUT 3
OUT 2
11
-IN 3
NC
12
+IN 3
-VL
13
+V
OUT 3
14
+IN 4
-IN 3
15
-IN 4
+IN 3
16
OUT 4
NC
17
----
+V
18
----
+IN 4
19
----
-IN 4
20
----
OUT 4
NC = No connect ion
FIGURE 1. Terminal connections.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-86860
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
C SHEET 6
DSCC FORM 2234
APR 97
FIGURE 2. Offset voltage and sensitivity waveforms.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-86860
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
C SHEET 7
DSCC FORM 2234
APR 97
NOTE: Response time testing is done after VIO testing to acquire device offset voltage.
Ten millivolts overdrive is then added (or subtracted depending on state) to this
measured VIO value.
FIGURE 3. Response time waveforms.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-86860
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
C SHEET 8
DSCC FORM 2234
APR 97
3.6 Certif i cate of compli an ce. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved sour ce of supply in M IL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and
Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturer's product meets the
requireme nts of M IL-PRF-38535, appendix A and the requirements herein.
3.7 Certif i cate of conform anc e . A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
with each lot of microcir cui ts d eliv ered to this draw ing.
3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be required for any change that
affects this drawing.
3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritime 's agent, and the acquiring activity retain the
option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made
available onshore at the option of the reviewer.
4. VERIFICATION
4.1 Sampling an d inspection . Sampling and inspection procedures shall be in accordance with MIL-PRF-38535,
appendix A.
4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices
prior to quality conformance inspection. The following additional criteria shall apply:
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify
the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method
1015 of MIL-STD-883.
(2) TA = +125°C, minimum.
b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
4.3 Quality conformance insp ecti on. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-
883 including groups A, B, C, and D inspections. The following additional criteria shall apply.
4.3.1 Gro up A inspe ctio n.
a. Tests s hal l be as specif ied in table II herein.
b. Subgroups 4, 5, 6, 7, 8, 10, and 11 in table I, method 5005 of MIL-STD-883 shall be omitted.
4.3.2 Groups C and D inspections.
a. End-point elec tr ic al para meters shall be as specified in table II herein.
b. Steady-state life test conditions, method 1005 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision
level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
method 1005 of MIL-STD-883.
(2) TA = +125°C, minim um.
(3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-86860
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
C SHEET 9
DSCC FORM 2234
APR 97
TABLE II. Electrical test requirements.
MIL-STD-883 test requirements Subgroups
(in accordance with
MIL-STD-883, method 5005,
table I)
Interim electrical parameters
(method 5004)
----
Final electrical test parameters
(method 5004)
1*, 2, 3
Group A test requirements
(method 5005)
1, 2, 3, 9
Groups C and D end-point
electrical parameters
(method 5005)
1
* PDA applies to subgroup 1.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A.
6. NOTES
6.1 Inten ded use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equ ipm ent), des ign applicat ion s, and logi sti cs purpo ses.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-
prepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for
the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal.
6.4 Record of user s. Mil itary and industrial users shall inform DLA Land and Maritime when a system application requires
configuration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this
list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics
devices (FSC 5962) should co ntact DLA Land and Maritime -VA, telephone (614) 692-0544.
6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime -VA, Columbus, Ohio 43218-
3990, or telephone (614) 692-0540.
6.6 Approv ed sour ce s of supp ly . Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in M IL-
HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by
DLA Land and Maritime -VA.
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 11-03-08
Approved sources of supply for SMD 5962-86860 are listed below for immediate acquisition information only and
shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QM L-38535 will be
revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been submitted to and accepted by DLA Land and Maritime -VA. This information
bulletin is supers eded by the next dated revision of M IL-HDBK-103 and QML-38535. DLA Land and M aritim e
maintains an online database of all current sources of supply at http://www.dscc.dla.mil/Programs/Smcr/.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-8686001EA 34371 HA1-4902/883
5962-86860012A 34371 HA4-4902/883
1/ The lead finish shown for each PIN representing
a hermetic package is the most readily available
from the manufac turer lis ted f o r that part. If the
desired lead finish is not listed contact the vendor
to determine its availa bil it y .
2/ Caution. Do not use this number for item
acquisition. Items acquired to this number may not
satisfy the perf orma nce requirements of this drawing.
Vendor CAGE Vendor name
number and address
34371 Intersil Corporation
1001 Murphy Ranch Road
Milpitas, CA 95035-6803
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.
