LT8316 600VIN Micropower No-Opto Isolated Flyback Controller FEATURES DESCRIPTION Wide Input Voltage Range: 16V to 600V nn No Opto-Isolator Required for Regulation nn Quasi-Resonant Boundary Mode Operation nn Constant-Current and Constant-Voltage Regulation nn Low-Ripple Light Load Burst Mode(R) Operation nn Low Quiescent Current: 75A nn Programmable Current Limit and Soft-Start nn TSSOP Package with High-Voltage Spacing The LT(R)8316 is a micropower, high voltage flyback controller. No opto-isolator is needed for regulation. The device samples the output voltage from the isolated flyback waveform appearing across a third winding on the transformer. Quasi-resonant boundary mode operation improves load regulation, reduces transformer size, and maintains high efficiency. nn APPLICATIONS Isolated Telecom, Automotive, Industrial, Medical Power Supplies nn Isolated Off-Line Housekeeping Power Supplies nn Electric Vehicles and Battery Stacks nn Multioutput Isolated Power Supplies for Inverter Gate Drives nn At start-up, the LT8316 charges its INTVCC capacitor via a high voltage current source. During normal operation, the current source turns off and the device draws its power from a third winding on the transformer minimizing standby power dissipation. The LT8316 operates from a wide range of input supply voltages and can deliver up to 100W of power. It is available in a thermally enhanced 20-pin TSSOP package with four pins removed for high-voltage spacing. All registered trademarks and trademarks are the property of their respective owners. TYPICAL APPLICATION 16VIN to 600VIN Isolated 12VOUT Supply VIN 16V TO 600V Efficiency 95 8:1:1 VIN 47pF EN/UVLO SMODE 540H 108k TC GATE VC 100nF 8.44H FB LT8316 20k 44.2k DCM INTVCC 4.7F 10k BIAS VOUT+ 12V 8.44H 1300F VOUT- 30mA TO 800mA (VIN = 20V) 30mA TO 3A (VIN = 80V) 50mA TO 4A (VIN = 160V TO 600V) 4.99k M1 GND 85 80 VIN = 20V VIN = 80V VIN = 160V VIN = 320V VIN = 600V 75 70 SENSE IREG/SS 90 EFFICIENCY (%) 4.7F 0 1 2 3 4 LOAD CURRENT (A) 5 6 8316 TA01b 40m 61.9k 8316 TA01a Rev. 0 Document Feedback For more information www.analog.com 1 LT8316 ABSOLUTE MAXIMUM RATINGS PIN CONFIGURATION (Note 1) VIN...........................................................................600V BIAS, EN/UVLO..........................................................40V INTVCC.......................................................................15V SMODE, GATE...................................................... INTVCC SENSE, TC, FB, VC, IREG/SS........................................4V DCM.................................................................... 100mA Operating Junction Temperature (Note 2) LT8316E, LT8316I............................... -40C to 125C Storage Temperature Range................... -65C to 150C Lead Temperature (Soldering, 10 sec).................... 300C TOP VIEW VIN 1 VIN 2 VIN 3 20 19 18 17 16 15 14 13 12 11 21 GND INTVCC 8 BIAS 9 DCM 10 GND GATE SENSE EN/UVLO SMODE GND IREG/SS VC FB TC FE PACKAGE 20(16)-LEAD PLASTIC TSSOP JA = 38C/W, JC = 10C/W EXPOSED PAD (PIN 21) IS GND, MUST BE SOLDERED TO PCB ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT8316EFE#PBF LT8316EFE#TRPBF LT8316FE 20-Lead Plastic TSSOP -40C to 125C LT8316IFE#PBF LT8316IFE#TRPBF LT8316FE 20-Lead Plastic TSSOP -40C to 125C Contact the factory for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Tape and reel specifications. Some packages are available in 500 unit reels through designated sales channels with #TRMPBF suffix. Rev. 0 2 For more information www.analog.com LT8316 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. BIAS = 30V, VEN/UVLO = 30V unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN 9.5 BIAS Chip Bias Voltage Supply Range After Startup IQ BIAS Quiescent Current Burst Mode Operation Active ICLAMP(MAX) BIAS Clamp Maximum Current VCLAMP BIAS Clamping Voltage ICLAMP = 200A ICLAMP = 15mA ISHDN VIN Shutdown Current VEN/UVLO < 0.3V, BIAS = Floating TYP MAX UNITS 75 470 150 700 A 15 mA 38 39 V V 20 A V 34 35 12 VIN(MIN) Minimum Input Voltage for Startup BIAS = Floating l ISTARTUP Startup Current Out of INTVCC VIN = 16V, BIAS = Floating l VUVLO EN/UVLO Threshold EN/UVLO Hysteresis INTVCC UVLO Rising Threshold 16 V 100 300 VEN/UVLO Falling VEN/UVLO Rising 1.18 30 1.22 65 1.26 120 V mV Startup Current through Depletion FET 11.1 12 13.1 V 7.6 8.1 8.6 V 9.5 10 10.5 V INTVCC UVLO Falling Threshold INTVCC Regulation Voltage Drawing 20mA from INTVCC A INTVCC LDO Dropout Voltage Drawing 20mA from INTVCC Gate Driver Rise Time CGATE = 3.3nF, 10% to 90% 30 1 ns V Gate Driver Fall Time CGATE = 3.3nF, 90% to 10% 8 ns VREG FB Regulation Voltage GM Voltage Error Amplifier Transconductance VFB = 1.22V 5mV VTC TC Voltage TC Voltage Temperature Coefficient TA = 25C ITC TC Sinking/Sourcing Current IIREG/SS IREG/SS Current Current Out-of-Pin IDCM Flyback Collapse Detection Threshold Resonant Valley Detection Threshold IDCM Rising IDCM Falling VSENSE(MIN) Minimum Current Voltage Threshold 14 20 26 mV VSENSE(MAX) Maximum Current Voltage Threshold 90 100 110 mV SENSE Input Bias Current Current Out-of-Pin FSW(MIN) Minimum Switching Frequency Burst Mode Standby Mode 3 187 3.5 220 4 250 kHz Hz FSW(MAX) Maximum Switching Frequency 138 140 142 kHz l 1.18 1.22 1.25 V 245 350 455 S 1.22 +4.1 V mV/C 100 Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. 9.7 A 10 10.3 A -170 -85 A A 35 A Note 2: The LT8316E is guaranteed to meet performance specifications from 0C to 125C junction temperature. Specifications over the -40C to 125C operating junction temperature range are assured by design characterization and correlation with statistical process controls. The LT8316I is guaranteed over the full -40C to 125C operating junction temperature range. High junction temperatures degrade operating lifetimes. Operating lifetime is derated at junction temperatures greater than 125C. Rev. 0 For more information www.analog.com 3 LT8316 TYPICAL PERFORMANCE CHARACTERISTICS Load and Line Regulation Output Voltage vs Temperature 12.2 FRONT PAGE APPLICATION OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 12.4 12.2 12.0 11.8 VIN = 20V VIN = 80V VIN = 160V VIN = 320V VIN = 600V 11.6 11.4 0 1 2 3 4 LOAD CURRENT (A) 5 6 FRONT PAGE APPLICATION VIN = 320V 12.0 11.9 11.8 -50 -25 IOUT = 100mA IOUT = 1A IOUT = 4A 0 25 50 75 100 125 150 TEMPERATURE (C) FREQUENCY (kHz) 9 VIN = 320V RIREG/SS = 61.9k 6 3 0 0 1 8316 G02 Switching Frequency 2 3 4 LOAD CURRENT (A) 5 6 8316 G03 Boundary Mode Waveforms FRONT PAGE APPLICATION 80 VSW 200V/DIV 60 VSENSE 100mV/DIV 40 VOUT AC COUPLED 50mV/DIV VIN = 20V VIN = 80V VIN = 160V VIN = 320V VIN = 600V 20 0 FRONT PAGE APPLICATION 12 12.1 8316 G01 100 CV/CC Operation 15 OUTPUT VOLTAGE (V) 12.6 TA = 25C, unless otherwise noted. 0 1 2 3 4 LOAD CURRENT (A) 5 5s/DIV 8316 G05 FRONT PAGE APPLICATION VIN = 320V, IOUT = 4A 6 8316 G04 Discontinuous Mode Waveforms Burst Mode Waveforms VSW 200V/DIV VSW 200V/DIV VSENSE 100mV/DIV VSENSE 100mV/DIV VOUT AC COUPLED 50mV/DIV VOUT AC COUPLED 50mV/DIV 5s/DIV FRONT PAGE APPLICATION VIN = 320V, IOUT = 2A 8316 G06 100s/DIV 8316 G07 FRONT PAGE APPLICATION VIN = 320V, IOUT = 30mA Rev. 0 4 For more information www.analog.com LT8316 TYPICAL PERFORMANCE CHARACTERISTICS Load Transient Response TA = 25C, unless otherwise noted. Startup Waveforms VIN 320V/DIV VOUT AC COUPLED 200mV/DIV VBIAS 10V/DIV VINTVCC 10V/DIV IOUT 2A/DIV VOUT 10V/DIV 8316 G08 10ms/DIV 8316 G09 50ms/DIV FRONT PAGE APPLICATION VIN = 320V, ROUT= 3 VIN Pin Shutdown Current BIAS Pin Quiescent Current Depletion Startup Current 160 VIN = 100V VIN = 600V 1.6 150C 25C -55C 1.4 45 30 15 120 1.2 IINTVCC (mA) QUIESCENT CURRENT (A) SHUTDOWN CURRENT (A) 60 80 40 1.0 0.8 0.6 0.4 0.2 0 -50 -25 0 0 -50 -25 25 50 75 100 125 150 TEMPERATURE (C) 0 8316 G10 FB Regulation Voltage 3 6 9 VINTVCC (V) EN/UVLO Rising EN/UVLO Falling 12 15 8316 G12 TC Pin Voltage 1.240 1.80 1.235 1.30 1.25 1.20 1.60 1.230 TC VOLTAGE (V) FB REGULATION VOLTAGE (V) ENABLE THRESHOLD (V) 0 8316 G11 ULVO Threshold 1.35 0 25 50 75 100 125 150 TEMPERATURE (C) 1.225 1.220 1.215 1.210 1.40 1.20 1.00 1.205 1.15 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) 1.200 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) 8316 G14 8316 G13 0.80 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) 8316 G15 Rev. 0 For more information www.analog.com 5 LT8316 TYPICAL PERFORMANCE CHARACTERISTICS IREG/SS Pin Current Switching Frequency Limit 150 110 10.4 145 105 135 FREQUENCY (kHz) 10.2 10.1 10.0 9.9 9.8 100 MAXIMUM SWITCHING FREQUENCY SENSE VOLTAGE (mV) 140 130 125 5 4 3 9.7 MINIMUM SWITCHING FREQUENCY 90 85 25 20 9.6 1 5 9.5 -50 -25 0 -50 -25 25 50 75 100 125 150 TEMPERATURE (C) 0 Minimum Switch-Off Time 350 850 300 800 250 750 OFF TIME (ns) 900 150 100 DCM Pin Threshold -20 -40 700 650 25 50 75 100 125 150 TEMPERATURE (C) 8316 G19 500 -50 -25 -60 -80 RESONANT VALLEY DETECT -100 -120 -140 -160 FLYBACK COLLAPSE DETECT -180 550 0 25 50 75 100 125 150 TEMPERATURE (C) 0 600 50 0 8316 G18 DCM CURRENT (A) Minimum Switch-On Time 0 -50 -25 0 -50 -25 25 50 75 100 125 150 TEMPERATURE (C) 8316 G17 400 200 MINIMUM CURRENT LIMIT 15 10 0 MAXIMUM CURRENT LIMIT 95 2 8316 G16 MINIMUM ON TIME (ns) Switch Current Limit 10.5 10.3 IREG/SS CURRENT (A) TA = 25C, unless otherwise noted. -200 0 25 50 75 100 125 150 TEMPERATURE (C) 8316 G20 -220 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) 8315 G21 Rev. 0 6 For more information www.analog.com LT8316 PIN FUNCTIONS VIN (Pins 1, 2, 3): Drain of the 600V Internal Startup FET. During startup, an internal depletion MOSFET draws power from this pin to charge the INTVCC capacitor. INTVCC (Pin 8): Internal Gate Driver Bias Voltage. During start-up, current from the VIN pin charges this pin to 12V. During operation, a linear regulator from BIAS maintains this voltage at 10V. Bypass locally with a 2.2F ceramic 15V rated capacitor. BIAS (Pin 9): Unregulated Input Voltage for the IC. This pin derives power from a third winding on the transformer to provide power to INTVCC. Bypass locally with a 100nF capacitor. DCM (Pin 10): Discontinuous Conduction Mode Detector. This pin detects the dV/dt of the switching waveform, ensuring accurate output voltage sampling and quasiresonant boundary-mode switching. Connect a capacitor with series resistance from this pin to the third winding. See Boundary Mode Detection section. TC (Pin 11): Temperature Compensation Pin. This pin presents a proportional-to-absolute-temperature (PTAT) voltage, which is equal to the internal 1.22V reference voltage at 25C and rises with temperature by 4.1mV/C, to compensate for the output rectifier diode. Connect an appropriate resistor from this pin to FB. FB (Pin 12): Feedback Pin. The voltage appearing on this pin is sampled and regulated to equal the internal 1.22V reference voltage. Connect this pin to a resistor divider from the third winding to regulate the output voltage. VC (Pin 13): Loop Compensation Pin. An internal GM transconductance amplifier feeds this pin with an error current depending on the sampled FB voltage. The resulting voltage determines the switching frequency and peak current limit for power delivery. Connect a series R-C network to stabilize the regulator. See Loop Compensation section. IREG/SS (Pin 14): Current Regulation/Soft-Start Pin. A 10A current flows out of this pin. The resulting voltage sets the output current regulation point, as determined by an internal current regulation loop. Program the current with a resistor to GND, or connect a capacitor to implement soft-start. SMODE (Pin 16): Standby Mode Pin. Connect this pin to INTVCC to enable Standby Mode, which reduces the minimum switching frequency to 220Hz for ultralow quiescent power consumption. Connect to GND to disable. EN/UVLO (Pin 17): Enable/Undervoltage Lockout Pin. The chip will operate only if the voltage on this pin is greater than the internal 1.22V reference voltage. Connect to a resistor divider as desired, or connect to BIAS or INTVCC if UVLO functionality is not desired. SENSE (Pin 18): Current Sense Pin. The voltage appearing on this pin is used for peak current-mode control and current limiting. Connect a current-sensing resistor from the main power MOSFET to GND to program the current limit. Utilize a compact layout with the transformer and input capacitor to reduce EMI and voltage spikes. GATE (Pin 19): Gate Driver Output. Connect this pin to the gate of the main power MOSFET for the flyback converter. GND (Pins 15, 20, 21): Ground. Solder the exposed pad (Pin 21) to a ground plane for heat sinking. Rev. 0 For more information www.analog.com 7 LT8316 BLOCK DIAGRAM DOUT NPS :1 VIN CIN ZSNUB DSNUB LPRI * * VOUT + LSEC COUT VOUT - 9 VIN 1, 2, 3 BIAS CBIAS 36V LDO - 10V 600V DEPLETION FET + VUVLO M2 DBIAS + 8 17 EN/UVLO MASTER LATCH BIAS/REF CONTROL TSD CDRV 16 - INTVCC SMODE S Q GATE DRIVER 19 M1 R CDCM :NTS * RDCM 10 RFB2 12 LTER RFB1 DCM BOUNDARY DETECT FB x1 VOLTAGE CONTROLLED OSCILLATOR SENSE CURRENT COMPARATOR + RSNS x10 GND 15, 20, 21 - S&H 18 RTC 11 TC x1 +4.1mV/C CURRENT ERROR AMP VOLTAGE ERROR AMP - GM 1.22V 1.25x(1-D) - + 10A + 13 VC RC 14 IREG/SS 8316 BD RIREG CC Rev. 0 8 For more information www.analog.com LT8316 OPERATION The LT8316 is a high-voltage current-mode switching controller designed for the isolated flyback topology. The problem normally encountered in such circuits is that information relating to the output voltage on the isolated secondary side of the transformer must be communicated to the primary side in order to achieve regulation. This is often performed by opto-isolator circuits, which waste output power, require extra components that increase the cost and physical size of the power supply, and exhibit trouble due to limited dynamic response, nonlinearity, unit-to-unit variation, and aging over their life. The LT8316 does not need an opto-isolator because it derives information about the isolated output voltage by examining the flyback pulse waveform appearing on a tertiary winding on the transformer. The output voltage is easily programmed with two resistors. Boundary Mode Operation Boundary mode is a variable frequency, current-mode switching scheme. The external N-channel MOSFET turns on and the inductor current increases until it reaches the limit determined by the voltage on the VC pin and the sense resistor's value. After the MOSFET turns off, the voltage on the tertiary winding rises to the output voltage multiplied by the transformer tertiary-to-secondary turns ratio. After the current through the output diode falls to zero, the voltage on the tertiary winding falls. A boundary mode detection comparator on the DCM pin detects the negative dV/dt associated with the falling voltage and triggers the sample-and-hold circuit to sample the FB voltage. When the tertiary voltage reaches its minimum and stops falling, the boundary mode comparator turns the internal MOSFET back on for minimal switching energy loss. The LT8316 features a boundary mode control method (also called critical conduction mode), where the part operates at the boundary between continuous conduction mode and discontinuous conduction mode. Due to boundary mode operation, the output voltage can be determined from the tertiary winding's voltage when the secondary current is almost zero. This method improves load regulation without extra resistors and capacitors. Boundary mode operation returns the secondary current to zero every cycle, so parasitic resistive voltage drops do not cause load regulation errors. Boundary mode also allows the use of a smaller transformer compared to continuous conduction mode and does not exhibit subharmonic oscillation. The Block Diagram shows an overall view of the system. Many of the blocks are similar to those found in traditional switching regulators, including a current comparator, internal reference, LDO, logic, timers and a MOSFET gate driver. The novel sections include a special sampling error amplifier, a temperature compensation circuit, an output current regulator, and a depletion-mode startup FET. As the load gets lighter, the peak switch current decreases. Maintaining boundary mode requires the switching frequency to increase. An excessive switching frequency increases switching and gate charge losses. To limit these losses, the LT8316 features an internal oscillator which limits the maximum switching frequency to 140kHz. Once the switching frequency hits this limit, the part starts to reduce its switching frequency and operates in discontinuous conduction mode. Depletion Startup FET The LT8316 features an internal depletion mode MOSFET. At startup, this transistor charges the INTVCC capacitor so that the LT8316 has power to begin switching. This removes the need for an external bleeder resistor or other components. Discontinuous Conduction Mode Operation Low Ripple Burst Mode Operation Unlike traditional flyback converters, the MOSFET has to turn on and off to generate a flyback pulse in order to update the sampled output voltage. The duration of a well-formed flyback pulse must exceed the minimum-off time for proper sampling. To this end, a minimum switch turn-off current is necessary to ensure a flyback pulse of sufficient duration. Rev. 0 For more information www.analog.com 9 LT8316 OPERATION As the load gets very light, the LT8316 reduces switching frequency while maintaining the minimum current limit in order to reduce current delivery while still properly sampling the output voltage. Because flyback pulses must be generated to regulate the output, a minimum switching frequency of 3.5kHz is enforced. The minimum switching frequency determines how often the output voltage is sampled and introduces a minimum load requirement of approximately 1% of the maximum load power. Tying the SMODE pin to INTVCC enables Standby Mode, which reduces the minimum switching frequency to 220Hz, reducing the minimum load requirement at the expense of a longer period between samples. CV/CC Regulation Like a traditional voltage regulator, the LT8316 implements a GM transconductance amplifier that regulates the output voltage. In addition, the LT8316 includes a current regulation loop which regulates the estimated output current to a point set by the voltage on the IREG/SS pin. Below the current setpoint, the output voltage is regulated for constant-voltage (CV) regulation. Below the voltage setpoint, the the output current is regulated for constantcurrent (CC) regulation. APPLICATIONS INFORMATION The LT8316 is designed to be an easy-to-use, yet fullyfeatured flyback controller. With proper technique, it is simple to build an efficient and robust power solution. However, the voltage and power levels involved can be lethal. Milliamperes from a high voltage power supply can cause heart fibrillation and death. Never touch conductive nodes while the circuit is active, and keep one hand behind your back while probing. Depletion Startup FET The LT8316 features an internal depletion-mode FET, which has a negative threshold voltage and is therefore normally on. At startup, this FET charges the INTVCC capacitor to 12V so that the LT8316 has power to begin switching. This removes the need for an external bleeder resistor or other startup components. Once INTVCC is charged, the depletion-mode FET turns off. The depletion FET is current-limited to avoid destructive power levels. To ensure start-up, do not load INTVCC or BIAS with excessive current while the chip is starting. ENABLE and Undervoltage Lockout (UVLO) A resistive divider from VIN to the EN/UVLO pin implements undervoltage lockout (UVLO). The EN/UVLO pin threshold is set at 1.22V. Upon startup, the EN/UVLO pin exhibits a ~65mV hysteresis voltage to prevent oscillations. The EN/UVLO pin can also be driven with logic levels and set by the output pin of a digital controller. Otherwise, EN/UVLO can also be tied to BIAS or INTVCC to keep the chip enabled. Output Voltage The output voltage is programmed by the RFB1 and RFB2 resistors depicted in the Block Diagram. The LT8316 operates similarly to traditional current-mode switchers, except in its use of a unique sample-and-hold error amplifier, which regulates the isolated output voltage from the sampled flyback pulse. Operation is as follows: when the power switch M1 turns off, the voltage across the tertiary winding rises. The amplitude of the flyback pulse is given as: VFLBK = (VOUT + VF + ISEC * ESR) * NTS, Rev. 0 10 For more information www.analog.com LT8316 APPLICATIONS INFORMATION where where VF = Output diode (DOUT) forward-biased voltage VOUT = Desired output voltage ISEC = Transformer secondary current VF = Output diode (DOUT) forward voltage 300mV ESR = Parasitic resistance of secondary circuit NTS = Transformer tertiary-to-secondary turns ratio NTS = Transformer tertiary-to-secondary turns ratio The voltage divider formed by RFB1 and RFB2 feeds a scaled version of the flyback pulse to the FB pin, where it is sampled and fed to the error amplifier. Because the sample-and-hold circuit samples the voltage when the secondary current is nearly zero, the (ISEC * ESR) term in the VFLBK equation can be ignored. The internal 1.22V reference voltage feeds the non-inverting input of the error amplifier. The high gain of the overall loop causes the FB voltage to be nearly equal to the reference voltage. The resulting flyback voltage VFLBK can be expressed as: R VFLBK = 1+ FB2 * 1.22V RFB1 Combining with the previous VFLBK equation and solving for VOUT yields: R 1.22V VOUT = 1+ FB2 * - VF RFB1 N TS Due to the fast nature of the flyback pulse, it is recommended to keep RFB1 between 1k and 10k in order to preserve the resistor divider's dynamic response. Selecting the RFB2 Resistor Value The LT8316 uses a unique sampling scheme to regulate the isolated output voltage. Due to its sampling nature, the scheme exhibits repeatable delays and error sources, which will affect the output voltage and force a re-evaluation of the resistor values. With a fixed value for RFB1 (such as 10k) chosen, rearrangement of the expression for VOUT yields the starting value for RFB2: Power up the application with the final power components installed and the starting RFB2 value, and measure the regulated output voltage, VOUT(MEAS). The final RFB2 value can be adjusted to: RFB2(FINAL) (RFB2 + RFB1) * VOUT VOUT(MEAS) - RFB1 Once the final RFB2 value is selected, the regulation accuracy from board to board for a given application will be very consistent, typically within 5% when including device variation of all the components in the system (assuming resistor tolerances and transformer windings matching within 1%). However, if the transformer or the output diode is changed, or the layout is dramatically altered, there may be some change in VOUT. Example: Consider a 12V output supply with an output diode whose forward voltage at nearly zero current is 300mV at room temperature. If the tertiary-to-secondary ratio NTS is 1 and RFB1 is 10k, then RFB2 is calculated as 90.9k. The application is powered up and the output is slightly high at 12.2V, so RFB2 is adjusted to 88.7k. Output Diode Temperature Compensation Reiterating the equation for VOUT, R 1.22V VOUT = 1+ FB2 * - VF RFB2 N TS The first term in the VOUT equation is insensitive to temperature, but the output diode forward voltage VF has a significant negative temperature coefficient (from -1mV/C to -2mV/C). Such a temperature coefficient produces approximately 200mV to 400mV output voltage variation across operating temperature. V + VF RFB2 = RFB1 * OUT * N TS - 1 1.22V Rev. 0 For more information www.analog.com 11 LT8316 APPLICATIONS INFORMATION At higher output voltages, the resulting variation may be unimportant as it represents a small fraction of the total output. However, for lower output voltages, the diode temperature coefficient accounts for a large output voltage error. To correct this error, the TC pin provides a buffered proportional-to-absolute-temperature (PTAT) voltage. At room temperature, this voltage is equal to the internal 1.22V reference, and it has a +4.1mV/C temperature coefficient. The output diode's temperature coefficient TCF can easily be found experimentally by applying a uniform temperature to both the output diode and the LT8316. First, RFB1 and RFB2 are adjusted to give the desired output voltage at room temperature. The temperature is then raised or lowered by a known amount to a new temperature, and the diode temperature coefficient is found as: TCF = VOUT(25C) - VOUT(TNEW) TNEW - 25C where VOUT(25C) = VOUT measured at room temperature VOUT(TNEW) = VOUT measured at new temperature TNEW = New temperature in Celsius Alternatively, TCF can be found more accurately by measuring VOUT at two extremes of temperature and computing: TCF = - With the output diode's temperature coefficient known, a resistor RTC is then attached from the TC pin to the FB pin. Its value can be calculated as: R TC = -RFB2 * 4.1mV / C TCF * N TS Example: If the output diode's temperature coefficient TCF is found experimentally to be -1.9mV/C, then with RFB2 = 88.7k, a RTC value of 191k will yield a temperatureinvariant output voltage. Sense Resistor Selection The resistor RSNS between the power MOSFET and GND should be selected to provide an adequate switch current to drive the application without exceeding the current limit threshold. At maximum current delivery, current limit occurs when the SENSE pin voltage is 100mV. In boundary mode, the maximum output current will depend on the duty cycle D and is given by: IOUT(MAX) 100mV 2 * R SNS * (1- D ) * NPS where NPS = Transformer primary-to-secondary turns ratio D ( VOUT + VF ) * NPS ( VOUT + VF ) * NPS + VIN VIN = Power supply voltage. VOUT T It should be noted that for this measurement, it is critical that the entire board be heated or cooled uniformly, for example by an oven. A heat gun or freeze spray will not suffice, since the heating and cooling will not be uniform, and dramatic temperature mismatch between the LT8316 and the output diode will cause significant error. If no method is available to apply uniform heat or cooling, extrapolating data from the diode's data sheet or assuming a nominal TCF value (such as -1.5mV/C) may yield a satisfactory result. It should be noted that the worst-case occurs at minimum VIN, so DVIN(MIN) should be calculated assuming VIN = VIN(MIN). Solving for the sense resistor value: R SNS = 1- D VIN(MIN) IOUT(MAX) * 50mV * NPS * 80% A factor of 80% is introduced to compensate for system delays and tolerances, but it may need adjustment for the final application. Rev. 0 12 For more information www.analog.com LT8316 APPLICATIONS INFORMATION Example: A 12V output voltage is generated from a VIN = 400V input that can drop as low as VIN(MIN) = 250V. If a transformer with primary-to-secondary turns ratio NPS = 10 is selected to supply a maximum output current IOUT(MAX) = 2A, then the duty cycle is DVIN(MIN) 33% and the sense resistor is calculated RSNS = 133m. A 120m resistor is selected. where A more accurate value for RSNS can be obtained by finding D experimentally with an oscilloscope and electronic load. The calculated power is approximate, and does not take into account timing variations caused by circuit parasitics. The actual output power must be evaluated on the bench. Output Power Compared with a buck or a boost converter, a flyback converter has a complicated relationship between the input and output currents. Boost converters have relatively constant maximum input current regardless of input voltage, while buck converters have relatively constant maximum output current regardless of input voltage, owing to the fact that they have continuous input and output currents respectively. A flyback converter, however, has both discontinuous input and output currents. The duty cycle affects both input and output currents, making it hard to predict maximum output power. The following equation calculates output power: = Efficiency 80% D ( VOUT + VF ) * NPS ( VOUT + VF ) * NPS + VIN ISW(MAX) = Max. switch current limit = 100mV/RSNS Example: Consider a 12V output converter with a VIN(MIN) of 250V and a VIN(MAX) of 500V. With a ten-to-one primaryto-secondary winding ratio (NPS = 10) and a sense resistor RSNS = 120m, the maximum power output is 33W at VIN(MAX) = 500V but lowers to 28W at VIN(MIN) = 250V. Selecting a Transformer Transformer specification and design is possibly the most critical part of successfully applying the LT8316. In addition to the usual list of guidelines dealing with highfrequency isolated power supply transformer design, the following information should be carefully considered. Analog Devices has worked with several leading magnetic component manufacturers to produce pre-designed flyback transformers for use with the LT8316. Table 1 shows the details of these transformers. POUT = 0.5 * * VIN * D * ISW(MAX) Table 1. Predesigned Transformers -- Typical Specifications TRANSFORMER PART NUMBER LPRI (H) NP:NS:NT ISOLATION VENDOR TARGET APPLICATIONS 11328-T078 670 8:1:1 Reinforced Sumida 100V-600V to 12V/3A 11328-T080 670 4:1:0.5 Reinforced Sumida 100V-600V to 24V/1.5A 11328-T073 670 2:1:0.25 Reinforced Sumida 100V-600V to 54V/0.7A 11328-T061 600 5:1:1 Basic Sumida 200V-450V to 15V/2A 11338-T195 1000 14:1:1.7 Basic Sumida 100V-400V to 7V/2A 11328-T074 500 8:1:1 Reinforced Sumida 100V-450V to 12V/3A 15364-T008 1500 20:1:2.4 Reinforced Sumida 25V-450V to 5V/1A 11328-T086 70 4:1:0.5 Reinforced Sumida 30V-260V to 24V/3A 00399-T239 2800 6:1:0.7 Functional Sumida 90V-500V to 16.8V/0.4A 750317463 440 8:1:1 Reinforced Wurth Elektronik 100V-600V to 12V/4A 750317589 670 8:1:1 Reinforced Wurth Elektronik 100V-600V to 12V/3A 750317464 440 4:1:0.5 Reinforced Wurth Elektronik 100V-600V to 24V/2A 11328-T060 800 18:1:3 Reinforced Sumida 140V-450V to 5V/7A Rev. 0 For more information www.analog.com 13 LT8316 APPLICATIONS INFORMATION Flyback Transformer Modeling A flyback transformer can be thought of as an ideal transformer with a parallel magnetizing inductance and series leakage inductances, as shown in Figure 1. LLEAK(PRI) NPS :1 LLEAK(SEC) LPRI 8316 F01 IDEAL Figure 1. Transformer Model The magnetizing inductance, which is the mutual inductance shared by both primary and secondary windings, is essential for absorbing energy and delivering it to the load. It stores energy in magnetic flux lines that pass through both primary and secondary windings. If the leakage inductances are small, the magnetizing inductance can be measured by leaving the secondary open-circuited and measuring the inductance of the primary, resulting in an inductance LPRI. The magnetizing inductance can also be measured from the secondary by leaving the primary open-circuited and measuring the secondary inductance LSEC. The relationship between the primary-referred magnetizing inductance and secondaryreferred magnetizing inductance is given by the primaryto-secondary turns ratio NPS as: LPRI = LSEC * NPS2 The transformer also has leakage inductances, which are parasitic inductances associated with each winding. These inductances store energy in magnetic flux lines which "leak" out of the magnetic core and do not pass through both windings, and therefore represent selfinductances whose energy cannot be transferred through the transformer. As such, they contribute to energy loss and reduced converter efficiency. If the leakage inductances are small, the combined leakage inductance can be measured by short-circuiting the secondary and measuring the primary inductance. This results in a primary-referred inductance, LLEAK = LLEAK(PRI) + LLEAK(SEC) * NPS2 The leakage inductance and magnetizing inductance are related by the coupling coefficient k according to the relation: k= L PRI L PRI + L LEAK / 2 Coupling coefficients of k=99% are common, and are a function of transformer construction and materials. Increased voltage isolation between primary and secondary is often desired for safety purposes, but generally reduces the coupling coefficient and increases leakage inductance. Bifilar windings maximize the coupling coefficient, but are often undesirable because of their minimal isolation and increased primary-to-secondary capacitance. In the end, a reasonable trade-off between isolation and coupling coefficient must be made. Magnetizing Inductance Requirement The appropriate magnetizing inductance depends on the LT8316's minimum switch-on time, its minimum switchoff time, and output power. The conduction of secondary current reflects the output voltage onto the tertiary winding during the flyback pulse. The LT8316 obtains output voltage information from the reflected output voltage on the FB pin. The sample-andhold error amplifier needs a minimum of 800ns to settle and sample the reflected output voltage. In order to ensure proper sampling, the secondary winding needs to conduct current for at least 800ns. The minimum value for primary-side magnetizing inductance is given by: L PRI tOFF(MIN) * NPS * ( VOUT + VF ) ISW(MIN) where tOFF(MIN) = Minimum switch-off time = 800ns ISW(MIN) = Minimum switch current limit = 20mV/RSNS The LT8316 has a minimum switch-on time that prevents the chip from turning on the power switch for a period shorter than 300ns in order to blank the initial switch Rev. 0 14 For more information www.analog.com LT8316 APPLICATIONS INFORMATION turn-on current spike. If the inductor current exceeds the minimum switch current limit during that time, the minimum load current will increase. Therefore, the following equation must also be observed: L PRI tON(MIN) * VIN(MAX) ISW(MIN) where tON(MIN) = Minimum Switch-On Time = 300ns Additionally, the magnetizing inductance must be large enough to provide sufficient power to the output when the LT8316 operates at maximum frequency. This creates a third requirement for magnetizing inductance: L PRI 2 * (VOUT + VF ) * IOUT(MAX) 2 * ISW(MAX) * fSW(MAX) where Example: For a 12V/2A output converter with VIN(MAX) = 500V, VF = 300mV, NPS = 10, and RSNS = 120m, the first equation requires LPRI 590H, the second equation requires LPRI 900H, and the third equation requires LPRI 633H. A reasonable standard value for primary inductance is LPRI = 1.2mH. If a larger minimum load at high VIN can be tolerated, 820H is acceptable. The fourth equation dictates that LPRI must be less than 5.9mH; this requirement is easily satisfied by both options. Saturation Current The current in the transformer windings should not exceed its rated saturation current. Beyond its saturation value, the inductance drops and the current rises to an uncontrolled value, causing extra power dissipation and possible failure. Choose a transformer whose primary saturation current is at least 30% greater than ISW(MAX), which is 100mV/RSNS. ISW(MAX) = Maximum switch current = 100mV/RSNS Turns Ratios IOUT(MAX) = Maximum load current Typically, choose the transformer primary-to-secondary turns ratio NPS to maximize available output power. For low output voltages, a larger NPS ratio can be used to maximize the transformer's current gain. However, remember that the MOSFET's drain sees a voltage that is equal to VIN plus the output voltage multiplied by NPS. Additionally, leakage inductance will cause a voltage spike (VLEAKAGE) that adds to this reflected voltage. This total quantity needs to remain below the absolute maximum rating of the MOSFET's drain to prevent breakdown. Together these conditions place an upper limit on the turns ratio NPS for a given application. Choose a turns ratio low enough to ensure: fSW(MAX) = Maximum switching frequency = 140kHz = Efficiency 80% In general, choose a transformer with its primary magnetizing inductance about 20% to 50% larger than the minimum values calculated above. In addition to these minimum values, the magnetizing inductance has a maximum value. To avoid a stuck output-low state, the LT8316 has a 50s backup timer that turns the switch on if the secondary diode turn-off has not been detected. As a result, the magnetizing inductance must not be so large as to cause secondary diode conduction to exceed this time. This creates a final requirement for maximum magnetizing inductance: LPRI < 0.8 * ( VOUT + VF ) *NPS * tBU ISW(MAX ) where tBU = Backup time = 50s NPS < VBR - VIN(MAX) - VLEAKAGE VOUT + VF where VBR = MOSFET breakdown voltage. For producing high output voltages, a low ratio NPS may be used. However, the multiplied capacitance presented to the transformer primary may cause ringing that exceeds Rev. 0 For more information www.analog.com 15 LT8316 APPLICATIONS INFORMATION the 300ns tON(MIN), causing light-load instability. Fully evaluate these applications before use with the LT8316. During operation, the LT8316 derives its power from a tertiary winding through its BIAS pin. BIAS must be maintained between 10V and 30V for proper operation. This dictates a tertiary-to-secondary turns ratio NTS of: 10V VOUT < N TS < 30V VOUT Example: For VOUT = 12V, NTS must lie between 0.83 and 2.5, or a 5:6 and 5:2 tertiary-to-secondary ratio respectively. Due to leakage inductance ringing on the tertiary winding, BIAS will rise above its nominal value. To prevent BIAS pin breakdown, an internal clamp circuit activates at 36V and shunts the excess current to ground. This current must not exceed 15mA; evaluate at maximum load current and minimum VIN to verify proper operation. Because the output voltage is measured through the voltage appearing on the third winding, NTS directly affects the output voltage regulation accuracy. For best results, make sure the transformer is manufactured with a precise turns ratio specified within 1%. VSW Leakage Inductance and Snubbers Any leakage inductance on either the primary or secondary windings causes a voltage spike to appear on the primary after the power switch turns off. This spike is increasingly prominent at higher load currents where more energy is stored in the leakage inductance. This energy cannot be delivered to the load, and must be dissipated as heat. It is thus very important to minimize transformer leakage inductance. When designing an application, adequate margin should be kept for the worst-case leakage voltage spikes even under overload conditions. In most cases, the reflected output voltage on the primary plus VIN should be kept below 80% of VBR, as shown in Figure 2. This leaves 20% margin for the leakage spike across line and load conditions. A larger voltage margin will be required for poorly wound transformers with excessive leakage inductance. In addition to the voltage spikes, the leakage inductance also causes the switching node to ring for a while after the power switch turns off. To prevent the voltage ringing from falsely triggering the boundary mode detector, the LT8316 internally blanks the boundary mode detector for 800ns. Any ringing after 800ns may trigger the power switch to turn back on again before the secondary current falls to zero, so the leakage inductance spike and associated ringing should be limited to less than 800ns. VSW 800ns tOFF > 800ns tOFF > 800ns TIME No Snubber VLEAKAGE <0.8VBR TIME with DZ Snubber TIME with RC Snubber 8316 F02 Figure 2. Maximum Voltages for SW Pin Flyback Waveform Rev. 0 16 For more information www.analog.com LT8316 APPLICATIONS INFORMATION L L * Z D * C * * R 8316 F03 DZ Snubber RC Snubber Figure 3. Snubber Circuits A snubber circuit is recommended for most applications. Figure 3 shows two types of snubber circuits that can protect the internal power switch: the DZ (diode-Zener) snubber and the RC (resistor-capacitor) snubber. The DZ snubber ensures a well-defined and consistent clamping voltage and has slightly higher power efficiency, while the RC snubber quickly damps the voltage spike ringing and provides better load regulation and EMI performance. Figure 2 shows the flyback waveforms with the DZ and RC snubbers. For the DZ snubber, proper care must be taken when choosing both the diode and the Zener diode. Choose a fast-recovery diode that has a reverse-voltage rating higher than the maximum DRAIN pin voltage. The Zener diode breakdown voltage should be chosen to balance power loss and switch voltage protection. The best compromise is to choose the largest voltage breakdown. Use the following equation to make the proper choice: VZENER(MAX) VBR - VIN(MAX) Multiple Zener diodes may be placed in series to attain the required voltage and power dissipation. The Zener diode must be rated to absorb the power loss in the clamp, which is due to energy storage in the leakage inductance and the primary-to-secondary commutation time, which decreases with higher clamp voltage. A 500mW Zener is typically recommended. Design the metal of the VIN trace for sufficient heat removal. For the RC snubber, the recommended design approach is to power up at low voltage to avoid overvoltage stress, measure the period of the ringing on the MOSFET's drain when the power switch turns off without the snubber (TRING), and then add capacitance CSNUBBER (starting with 100pF) until the period of the ringing is 1.5 to 2 times longer (TRING(SNUBBED)). The change in period will determine the value of the parasitic capacitance CSW, from which the parasitic inductance LLEAK can also be determined, according to the equations: CSW = CSNUBBER 2 TRING(SNUBBED) - 1 T RING 2 1 T LLEAK = RING * 2 CSW With the value of the switching node capacitance and leakage inductance known, a resistor can be added in series with the snubber capacitor to dissipate power and critically dampen the ringing. The equation for deriving the optimal series resistance is: R SNUBBER = L LEAK CSW Energy absorbed by the RC snubber will be converted to heat and will not be delivered to the load. In high power applications, the snubber resistor may need to be sized for thermal dissipation. Rev. 0 For more information www.analog.com 17 LT8316 APPLICATIONS INFORMATION Note that the switching node capacitance is sometimes dominated by transformer interwinding capacitance. Also note that oscilloscope probes present considerable loading capacitance. Use of low-capacitance, high-voltage 100x probes is recommended. Leakage Inductance and Output Diode Stress The output diode may also see increased reverse voltage stresses from leakage inductance. While it nominally sees a reverse voltage of the input voltage divided by NPS plus the output voltage when the MOSFET power switch turns on, the capacitance on the output diode and the leakage inductance form an LC tank which may ring beyond that expected reverse voltage. A snubber or clamp may be implemented to reduce the voltage spike if it is desired to use a lower reverse voltage diode. Secondary Leakage Inductance Leakage inductance on the secondary forms an inductive divider that effectively reduces the size of the tertiaryreferred flyback pulse used for voltage feedback. This will increase the output voltage by a similar percentage. Note that, unlike leakage spike behavior, this phenomenon is load independent. To the extent that the secondary leakage inductance is a constant percentage of mutual inductance (over manufacturing variations), this can be accommodated by adjusting the RFB2/RFB1 resistor ratio. Winding Resistance Resistance in either the primary or secondary will reduce conversion efficiency. Good output voltage regulation will be maintained despite winding resistance due to the boundary/discontinuous conduction mode operation of the LT8316. Boundary Mode Detection Boundary mode is a variable frequency switching scheme that always returns the secondary current to zero with every cycle. The DCM pin uses a fast, current-input comparator in combination with a small capacitor CDCM to detect when the flyback waveform's dV/dt is negative, indicating that the secondary diode has turned off and the flyback pulse on the tertiary winding is falling. To avoid false tripping due to leakage inductance ringing, a blanking time of 800ns is applied after the switch turns off. The detector triggers when CDCM draws 170A of current out of the DCM pin. This information is used to set the timing of the FB sample-and-hold and estimate the output current. This is not the best time to turn the switch on because the MOSFET's drain voltage is still nearly VIN + (VOUT * NPS), and turning the switch on would waste all the energy stored in the parasitic capacitance on the switching node. When the secondary current reaches zero, discontinuous ringing begins and the energy in the parasitic capacitance on the switch node resonates with the transformer's magnetizing inductance, delivering this energy back to VIN. The minimum voltage of the switching node during this discontinuous ring is VIN - (VOUT * NPS). This is the optimal moment to turn the switch back on, and the LT8316 does this by sensing when current drawn out of DCM falls to 85A. This switching technique increases efficiency by up to 5%. Typical CDCM values range from 10pF to 100pF. A good starting value is 47pF. If the LT8316 is observed not to run in boundary mode, then increasing this capacitor will help. An unnecessarily large CDCM value can cause premature switch turn-on and increased power loss. Excessive current delivered to the DCM pin can cause erratic behavior. To avoid this, a resistor RDCM can be added in series with CDCM to limit the current. Typical values range from 5k to 50k. Output Capacitor Selection The output capacitor should be chosen to minimize the output voltage ripple while considering the increase in size and cost of a larger capacitor. The following equation provides an estimate of the maximum output voltage ripple at steady-state: VRIPPLE L PRI *I LIM 2 2 * C OUT * VOUT where ILIM = Maximum primary current = 100mV/RSNS Rev. 0 18 For more information www.analog.com LT8316 APPLICATIONS INFORMATION This is a simplified equation; the actual ripple will depend on load current, duty cycle and capacitor ESR. The LT8316 samples the output voltage only when switching. As a result, when it is operating at its minimum frequency, a load transient may discharge the output capacitor before the device can respond. The output capacitor must be sufficient to prevent the load from brown-out in this event. Additional bulk capacitance may be desirable for this purpose. Output Current Regulation and Soft-Start Using duty cycle information and the current limit set by the VC pin, the LT8316 estimates the output current and regulates it to a setpoint determined by the voltage on the IREG/SS pin. The output current is regulated according to the equation: N *V IOUT = PS IREG/SS 25 * R SNS where Operation Under Light Output Loads The LT8316 detects the output voltage from the flyback pulse appearing on the tertiary winding, which requires delivering power to the output. Thus, the LT8316 delivers a minimum amount of energy even during light load conditions to ensure accurate output voltage information. The minimum operating frequency at minimum load is approximately 3.5kHz. The minimum delivery of energy creates a minimum load requirement on the output of approximately 1% of the maximum load power. A Zener diode sufficiently rated to handle the minimum load power can be used to provide a minimum load without decreasing efficiency in normal operation. In selecting a Zener diode for this purpose, the Zener voltage should be high enough that the diode does not become the load path during transient conditions but the voltage must still be low enough that the MOSFET and output voltage ratings are not exceeded when the Zener functions as the minimum load. Standby Mode Operation For extremely low no-load power dissipation, the LT8316 features a standby mode which is enabled by tying the SMODE pin to INTVCC. When the load current has dropped to zero, the LT8316 reduces its minimum switching frequency by a factor of 16 from 3.5kHz to 220Hz. This reduces the minimum load current by a factor of 16, at the cost of slower transient response. Because the output voltage is sampled only once every 4.6ms, the LT8316 will be unable to respond to load steps for up to this period. VIREG/SS = Voltage on IREG/SS pin. A trimmed 10A current flows out of the IREG/SS pin, so that a resistor tied from this pin to GND programs the output current according to the equation: RIREG/SS = 2.5M * IOUT * R SNS NPS Example: For an application with RSNS = 120m, NPS = 10, and a desired regulated output current IOUT = 2A, an IREG/SS resistor is selected RIREG/SS = 60.4k. Circuit parasitics, especially transformer capacitance, will influence the accuracy of output current regulation due to energy delivery to the parasitics. Although this effect is usually small, some iteration may be necessary if accuracy better than 5% is required. In this case, RIREG/SS can be implemented with a rheostat and adjusted until the desired output current is realized, and then replaced with a fixed-value resistor for production. When the rheostat is present, a small bypass capacitor is helpful to attenuate switching interference pickup by the rheostat. Additionally, an RC snubber placed across the secondary rectifier can improve current regulation accuracy. Soft-start functionality can also be implemented by connecting a capacitor from the IREG/SS pin to GND. The 10A current will act to charge the external soft-start capacitor. At startup, the regulated output current will rise monotonically until reaching voltage regulation. The softstart capacitor then charges entirely and the output current regulation loop will not interfere with voltage regulation. Rev. 0 For more information www.analog.com 19 LT8316 APPLICATIONS INFORMATION In order to avoid an undervoltage condition which causes the chip to shut down, the combined capacitance on the INTVCC and BIAS pins must be sufficient to power the LT8316 until the output achieves regulation. the transient performance will suffer. The value choice for CC is somewhat the inverse of the RC choice: if too small a CC value is used, the loop may be unstable and if too large a CC value is used, the transient performance will suffer. If power at VIN is removed, over-temperature protection is engaged, undervoltage lockout trips, or overcurrent in the sense resistor is detected, a 20 pull-down switch to GND discharges any capacitance on the IREG/SS pin for the duration of the fault plus 640s. Transient response may be evaluated with a load step box and adjusted with an adjustable RC compensation network. Stability should be confirmed over the full range of load current and input voltage. Protection from Shorted Output Conditions The LT8316 is rated to operate from a VIN up to 600V. Operation from a higher supply voltage is made possible by placing a Zener diode in series with the VIN pin, as shown in Figure 4. The voltage dropped across the Zener diode reduces the voltage applied to the chip, allowing the supply voltage to exceed 600V. During a shorted output condition, the LT8316 operates at the minimum operating frequency. In normal operation, the tertiary winding provides power to the IC, but the tertiary winding voltage collapses during a shorted condition. This causes the part's INTVCC UVLO of 8.1V (typical) to shutdown switching and charge through the depletion startup current source. The part starts switching again when INTVCC has reached its turn-on voltage of 12V. To protect the output diode from excessive power dissipation during overload conditions, it is advised to program the regulated output current with a resistor RIREG/SS. For voltage regulators, the programmed current should be 120% to 150% of the maximum load current to ensure current regulation does not interfere with voltage regulation. Extending Supply Voltage For example, a 600V Zener diode will, in principle, allow a supply voltage ranging from 616V to 1200V. It should be noted that 616V is needed only during start-up; after start-up, the LT8316 will continue to operate through transient dips in supply voltage. In practice, the input voltage range must be adjusted according to the Zener diode's voltage tolerance. VSUPPLY VIN Loop Compensation LT8316 The LT8316 is compensated using an external resistorcapacitor network on the VC pin. Typical values are in the range of RC = 20k and CC = 220nF. If too large an RC value is used, the part will be more susceptible to high frequency noise and jitter. If too small of an RC value is used, 8316 F04 Figure 4. Increased Supply Voltage with a Zener Diode Rev. 0 20 For more information www.analog.com LT8316 APPLICATIONS INFORMATION VIN 20V TO 600V 10 1F 4.7F VIN BIAS 10k 49.9k TC GATE VC SENSE IREG/SS 20 100 GND 56.2k VOUT+ 54V 4.7F 100V X7S 1nF 4.99k D4 22F 63V VOUT- 670H 549k LT8316 D2 168H D3 FB SMODE 100nF 10.5H DCM INTVCC 10k T1 8:4:1 47pF EN/UVLO 4.7F D1 3mA TO 200mA (VIN = 20V) 4mA TO 400mA (VIN = 50V) 8mA TO 700mA (VIN = 100V TO 600V) STD6N90K5 50m T1: SUMIDA 11328-T073 D1: BAV20WS-7-F D2: PDU340 D3: SMBJ188A D4: US1MFA 8316 F05 Figure 5. 94% Efficient Isolated 54V Supply Rev. 0 For more information www.analog.com 21 LT8316 APPLICATIONS INFORMATION VIN 140V TO 450V 100 4.7F D1 T1 18:1:3 4.7F 47pF 729k 6.98k VIN 10k BIAS EN/UVLO TC GATE VC 330nF 42.2k LT8316 SENSE IREG/SS 68.1k 2.5H D4 FB SMODE 10k 61.9k DCM INTVCC 4.7F 4.99k 10 100 GND 1nF 100F 10V X5R/X7R x3 22.5H 810H D5 M2 D2 3 M1 DRAIN VCC LT8309 GATE GND 62m 1500F 6.3V VOUT- D3 3.32k VOUT+ 5V 70mA TO 7A 120pF 1F INTVCC 4.7F T1: SUMIDA 11328-T060 M1: BSC052N08NS5 M2: IPD80R450P7 D1, D2: BAV21WS-7-F D3: IN4148 D4: SMAJ200A D5: CMMR1U-08 D6: CMHZ5258B D6 8316 F06 Figure 6. 91% Efficient Isolated 5V/7A Synchronous Flyback Converter Rev. 0 22 For more information www.analog.com LT8316 APPLICATIONS INFORMATION VIN 19V TO 600V D1 D2 BIAS 21.5k EN/UVLO 10F 10k DCM INTVCC 0.1F M1: TK3P80E L1: SUMIDA RPT129NP-102MB D1, D3: US1KFA D2: CMDSH2-3 10pF VIN LT8316 FB TC M1 GATE SMODE VC 2.49k 22.1k SENSE GND IREG/SS 100nF 220m 100nF L1 VOUT 12V 47F 10mA TO 200mA 16V X5R/X7R x3 1mH D3 8316 F07 Figure 7. Ultra-Wide Input Range Non-Isolated 12V Buck Converter D1 VIN 20V TO 500V 0.47F 100 4.7F 47pF BIAS EN/UVLO DCM FB INTVCC 77.8H SMODE 10k 330nF 130k 0.12A (VIN = 20V) 0.25A (VIN = 50V) 0.42A (VIN = 100V TO 500V) TC GATE VC 100 M1 SENSE IREG/SS 48.7k D3 10k 4.99k LT8316 4.7F 1\0F 50V X5R/X7R x4 T1 6:1 2.8mH VIN VOUT 16.8V/0.42A D2 GND 1nF 220m M1: IPD80R4K5P7 T1: SUMIDA 00399-T239 D1: PDS4150H D2: BAV20WS-7-F D3: CMZ5932 8316 F08 Figure 8. Non-Isolated 16.8V Gate Drive Supply Rev. 0 For more information www.analog.com 23 LT8316 APPLICATIONS INFORMATION VIN 36V TO 600V D1 0.1F D2 Optional UVLO Circuit D3 46.4k BIAS DCM 10k M1: TK3P80E L1: SUMIDA RPT129NP-152MB D1, D3, D4: US1KFA D2: CMDSH2-3 10pF 1M 10F R4 2.49k EN/UVLO 10nF 42.2k 10F VIN LT8316 INTVCC FB TC SMODE VC GND GATE SENSE IREG/SS 22.1k 100nF M1 100nF 220m L1 1.5mH D4 10F 50V X5R x3 VOUT 24V 10mA TO 200mA 8316 F09 Figure 9. Nonisolated 24V Buck Converter with Optional Undervoltage Lockout Rev. 0 24 For more information www.analog.com LT8316 PACKAGE DESCRIPTION FE Package Variation: FE20(16) 20-Lead Plastic TSSOP (4.4mm) (Reference LTC DWG # 05-08-1990 Rev O) Exposed Pad Variation BB 6.40 - 6.60* (.252 - .260) 5.68 (.224) REF 5.68 (.224) REF 20 19 18 17 16 15 14 13 12 11 6.60 0.10 1.78 (.070) REF SEE NOTE 4 5.00 0.10 0.42 0.48 (.019) REF 0.45 0.05 1.78 6.40 (.070) (.252) BSC 0.2 0.42 (.016) REF 0.22 1.78 (.070) 0.80 0.10 0.65 BSC 1 2 3 4.30 - 4.50* (.169 - .177) 0.09 - 0.20 (.0035 - .0079) 0.25 REF 0.50 - 0.75 (.020 - .030) NOTE: 1. CONTROLLING DIMENSION: MILLIMETERS MILLIMETERS 2. DIMENSIONS ARE IN (INCHES) 3. DRAWING NOT TO SCALE 8 9 10 4.83 (.1902) RECOMMENDED SOLDER PAD LAYOUT 1.20 (.047) MAX 0 - 8 0.65 (.0256) BSC 0.195 - 0.30 (.0077 - .0118) TYP 0.05 - 0.15 (.002 - .006) FE20(16) (BB) TSSOP REV O 1014 4. RECOMMENDED MINIMUM PCB METAL SIZE FOR EXPOSED PAD ATTACHMENT *DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.150mm (.006") PER SIDE Rev. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license For is granted implication or otherwise under any patent or patent rights of Analog Devices. more by information www.analog.com 25 LT8316 TYPICAL APPLICATION Wide Input Range 24V Flyback Converter VIN 20V TO 600V 10 1F D1 T1 8:2:1 4.7F 10.5H 47pF VIN EN/UVLO VC 220nF TC GATE SENSE IREG/SS VOUT+ 24V/1.5A 10F 50V X5R/X7R x2 670H 249k LT8316 42H D3 FB SMODE 10k 44.2k DCM INTVCC 4.7F 10k BIAS D2 4.99k 20 D4 1nF 56.2k VOUT- 6mA TO 400mA (VIN = 20V) 7mA TO 900mA (VIN = 50V) 20mA TO 1.5A (VIN = 100V TO 600V) STD6N90K5 100 GND 100F 35V 50m T1: SUMIDA 11328-T080 D1: BAV20WS-7-F0 D2: PDS4200H-13 D3: SMBJ188A D4: US1MFA 8316 TA03 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT8304/LT8304-1 100VIN Micropower Isolated Flyback Converter with 150V/2A Low IQ Monolithic No-Opto Flyback, SO-8 Package Switch LT8304-1 Is Recommended for High Output Voltages LT8300 100VIN Micropower Isolated Flyback Converter with 150V/260mA Switch Low IQ Monolithic No-Opto Flyback, 5-Lead TSOT-23 LT8303 100VIN Micropower Isolated Flyback Converter with 150V/0.45A Switch Low IQ Monolithic No-Opto Flyback, 5-Lead TSOT-23 LT8301 42VIN Micropower Isolated Flyback Converter with 65V/1.2A Switch Low IQ Monolithic No-Opto Flyback, 5-Lead TSOT-23 LT8302 42VIN Micropower Isolated Flyback Converter with 65V/3.6A Switch Low IQ Monolithic No-Opto Flyback, SO-8 Package LT8309 Secondary-Side Synchronous Rectifier Driver 4.5V VCC 40V, Fast Turn-On and Turn-Off, 5-Lead TSOT-23 LT3748 100V Isolated Flyback Controller 5V VIN 100V, No-Opto Flyback, MSOP-16(12) LT3798 Off-Line Isolated No-Opto Flyback Controller with Active PFC VIN and VOUT Limited Only by External Components LT8312 Boost Controller with Power Factor Correction VIN and VOUT Limited Only by External Components LT8315 560VIN Micropower Isolated Flyback Converter with 630V/300mA Switch Low IQ Monolithic No-Opto Flyback, TSSOP-20(16) Rev. 0 26 03/19 www.analog.com For more information www.analog.com ANALOG DEVICES, INC. 2019