NJG1506R SPDT SWITCH GaAs MMIC nGENERAL DESCRIPTION NJG1506R is a GaAs SPDT switch IC which features low loss, high isolation and low control current and ideally suitable for switching the RF receiving circuit of cellular phone. NJG1506R is operated in the wide frequency range from 50MHz to 3GHz at low voltage from 2.5V with a small VSP8 package. nFEATURES lSingle and low positive supply voltage lLow insertion loss lHigh isolation lTransmission Power lLow control current lPackage nPACKAGE OUTLINE NJG1506R +2.5~+5.5V 0.3dB typ. @f=1GHz, Pin=0dBm 28dBm typ. @f=1GHz, Pin=0dBm 19dBm max. @f=2GHz, VCTR=3.0V 1uA typ. @f=0.05~2.5GHz, Pin=10dBm VSP8 (Mount Size: 4.0x2.9x1.2mm) nPIN CONFIGURATION R TYPE (Top View) Pin Connection 1.VCTR2 1 8 2.P2 2 7 4.GND 3 6 5.PC 3.GND 6.GND 4 5 7.P1 8.VCTR1 nTRUTH TABLE "H"=VCTR (H), "L"=VCTR (L) VCTL1 H L L H VCTL2 L H L H P1-PC OFF ON P2-PC ON OFF Loss =15dB P1 Return Loss =-3dB Loss =15dB P2 Return Loss =-3dB Loss =16dB P1 Return Loss =-2dB Loss =16dB P2 Return Loss =-2dB Note) The values of "Loss" and "Return Loss" are typical values at 2.0GHz. -1- NJG1506R nABSOLUTE MAXIMUM RATINGS (Ta=25C, Zs=Zl=50) PARAMETER SYMBOL RATINGS UNITS Pin 28 dBm VCTR 6.0 V Power dissipation PD 320 mW Operating Temp. Topr -30~+85 C Storage Temp. Tstg -40~+150 C Input power Control voltage nELECTRICAL CHARACTERISTICS (VCTR (L)=0V, VCTR (H)=2.7V, Zs=Zo=50, Ta=25C) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Control voltage (L) VCTR (L) f=0.05~2.5GHz, Pin=10dBm -0.2 0 0.2 V Control voltage (H) VCTR (H) f=0.05~2.5GHz, Pin=10dBm 2.5 2.7 5.5 V Control current ICTR f=0.05~2.5GHz, Pin=10dBm - 1.0 2.0 uA Insertion loss1 LOSS1 f=1.0GHz, Pin=0dBm - 0.3 0.6 dB Insertion loss2 Isolation 1 LOSS2 f=2.0GHz, Pin=0dBm - 0.5 0.8 dB ISL1 f=1.0GHz, Pin=0dBm 25 28 - dB (PC-P1, PC-P2, P1-P2) ISL2 f=2.0GHz, Pin=0dBm 23 27 - dB Pin at 1dB compression point P-1dB f=2.0GHz 19.0 22.0 - dBm f=0.05~2.5GHz, ON STATE - 1.2 1.5 f=0.05~2.5GHz - 15 - (PC-P1, PC-P2, P1-P2) Isolation 2 VSWR Switching time -2- VSWR TSW ns NJG1506R nTYPICAL CHARACTERISTICS -3- NJG1506R nTYPICAL CHARACTERISTICS -4- NJG1506R nTYPICAL CHARACTERISTICS -5- NJG1506R nTYPICAL CHARACTERISTICS -6- NJG1506R nTYPICAL CHARACTERISTICS -7- NJG1506R nTYPICAL CHARACTERISTICS MARKER f (MHz) Ang. (o) 1 50 0.957 -20.2 2 800 0.782 171.2 3 1500 0.759 102.0 4 2000 0.747 61.8 5 3000 0.710 -11.3 MARKER f (MHz) 1 -8- Mag. o Mag. Ang. ( ) 50 0.968 -20.2 2 800 0.782 174.5 3 1500 0.749 108.2 4 2000 0.734 69.5 5 3000 0.690 -1.2 NJG1506R nTYPICAL CHARACTERISTICS Scattering Parameters: S11 (OFF STATE) (VCTR=0/2.7V, 50System) -9- NJG1506R nAPPLICATION CIRCUIT 1: Single control signal operation by using C-MOS inverter. [1] Please connect bypass capacitors to the supply terminals of the C-MOS inverter. [2] In order to stabilize input impedance of inverter, please pull down using 510K resister from the input terminal of the C-MOS inverter to the ground. nAPPLICATION CIRCUIT 2: Single control signal operation by using a transistor. - 10 - NJG1506R nTEST CIRCUIT nRECOMMENDED PCB DESIGN (TOP VIEW) PCB SIZE=19.5x14.0mm PC PCB: FR-4, t=0.2mm CAPACITOR: size 1005 C1 u P1 STRIPLINE WIDTH=0.5mm C3 C2 NJG1506R C4, C5: 10pF 1 C4 V CTR1 C1~C3: 56pF P2 C5 V CTR2 u: Please short between Pin4 and ground plane directly as close as possible. Precautions [1] External capacitors should be connected to the input and output RF terminals (P1, P2, PC) to block the DC current. The above example is a circuit at 900MHz. Please select the capacitor value suitable for actual frequency from 10pF to 1000pF. [2] Decoupling capacitors should be connected to the control terminals (VCTR1, VCTR2) as close as possible. The values of these capacitors should be selected from 5pF to 100pF range. Please consider that these values are very effective to switching time (Larger capacitor gives longer switching time). [3] In order to keep good isolation characteristics, the ground terminals (3, 4, 6pin) should be connected to the ground pattern with wider width as close as possible, and through-hole in the ground plane should also be placed as close as possible. - 11 - NJG1506R nPACKAGE OUTLINE (VSP8) Lead material Lead surface finish Molding material UNIT Weight Cautions on using this product This product contains Gallium-Arsenide (GaAs) which is a harmful material. * Do NOT eat or put into mouth. * Do NOT dispose in fire or break up this product. * Do NOT chemically make gas or powder with this product. * To waste this product, please obey the relating law of your country. This product may be damaged with electric static discharge (ESD) or spike voltage. Please handle with care to avoid these damages. - 12 - : Copper : Solder plating : Epoxy resin : mm : 22mg [CAUTION] The specifications on this databook are only given for information , without any guarantee as regards either mistakes or omissions. The application circuits in this databook are described only to show representative usages of the product and not intended for the guarantee or permission of any right including the industrial rights.