Digital Phosphor Oscilloscopes DPO7000 Series Datasheet Key features Ease of use features Pinpoint(R) Triggering provides the most flexible and highest performance triggering, with over 1400 combinations to address virtually any triggering situation Visual Trigger precisely qualifies triggers and finds unique events in complex waveforms Advanced Search and Mark to find specific events in the entire waveform MyScope(R) custom control windows and right mouse click menus for exceptional efficiency 53 automated measurements, waveform histograms, and FFT analysis for simplified waveform analysis Tektronix understands that engineers rely on an oscilloscope throughout their design cycle, from prototype turn-on to production testing. The DPO7000 Series oscilloscopes' unique capabilities combined with exceptional signal acquisition performance and analysis accelerate your measurement tasks. Key performance specifications TekVPI(R) Probe Interface supports active, differential, and current probes for automatic scaling and units 12.1 in. (307 mm) bright XGA display with touch screen Optional serial triggering and analysis Automated Serial Triggering, Decode, and Search Options for I2C, SPI, CAN, LIN, FlexRay, RS-232/422/485/UART, MIL-STD-1553, and USB 2.0 3.5 GHz, 2.5 GHz, 1 GHz, and 500 MHz bandwidth models Automated Serial Analysis Options for MIPI(R) D-PHY DSI-1 and CSI-2, 8b/10b, Ethernet, and PCI Express Up to 40 GS/s real-time sample rate on one channel, up to 20 GS/s on two channels, and up to 10 GS/s on three or four channels Clock Recovery from serial data streams Up to 500 megapoint record length with MultiView ZoomTM >250,000 wfms/s maximum waveform capture rate with FastAcqTM FastFrameTM segmented memory acquisition mode with >310,000 waveforms per second capture rate User-selectable bandwidth limit filters for better low-frequency measurement accuracy 64-bit NRZ Serial Pattern Trigger for isolation of pattern-dependent effects up to 1.25 Gb/s Optional technology specific analysis Software Solutions provide built-in domain expertise for MIPI(R) DPHY, Ethernet, MOST, and USB 2.0 Compliance Testing, Jitter, Timing, Eye Diagrams, Power, DDR Memory Bus Analysis, and Wideband RF Limit and Mask Testing provide quick insight into signal characteristics Connectivity USB Host Ports on the front and side panels for quick and easy data storage, printing, and connecting USB peripherals Integrated 10/100/1000BASE-T Ethernet port for network connection and Video Out port to export the oscilloscope display to a monitor or projector Microsoft(R) Windows 7 64-bit operating system for easy connectivity and integration into your environment LXI Class C compliant www.tektronix.com 1 Datasheet Simplified analysis for complex digital designs With the DPO7000C Digital Phosphor Oscilloscope Series, you can analyze analog and serial bus signals with a single instrument to quickly find and diagnose problems in complex designs. Bandwidths up to 3.5 GHz and sample rates up to 40 GS/s ensure you have the performance you need to see fast-changing signal details. To capture long windows of signal activity while maintaining fine timing resolution, the DPO7000C Series offers a deep record length of up to 12.5 M points standard on all channels and an optional record length of up to 500 M points on one channel. With Advanced Search and Mark and MultiView ZoomTM features for rapid waveform navigation, and more than 15 optional software and analysis packages for common technologies and in-depth analysis tasks, the DPO7000C Series from Tektronix provides the feature-rich tools you need to simplify and speed debug of your complex design. Comprehensive features speed every stage of debug The DPO7000C Series offers the industry's most complete visualization of signals, providing fast insight into the real operation of your device. Tektronix proprietary FastAcqTM technology delivers a fast waveform capture - greater than 250,000 waveforms per second - that enables you to see glitches and other infrequent transients within seconds, revealing the true nature of device faults. A digital phosphor display with color intensity grading shows the history of a signal's activity by using color to identify areas of the signal that occur more frequently, providing a visual display of just how often anomalies occur. Capture Discovering a device fault is only the first step. Next, you must capture the event of interest to identify root cause. The DPO7000C Series provides a complete set of triggers - including runt, glitch, width, timeout, transition, pattern, state, setup/hold violation, window, comm, and serial pattern - to help quickly find your event. Enhanced Triggering reduces trigger jitter at the trigger point. In this mode, the trigger point can be used as a measurement reference. The DPO7000C Series offers a robust set of features to speed every stage of debugging your design - from quickly discovering an anomaly and capturing it, to searching your waveform record for the event and analyzing its characteristics and your device's behavior. Discover To debug a design problem, first you must know it exists. Every design engineer spends time looking for problems in their design, a timeconsuming and frustrating task without the right debug tools. Capture - Triggering on a specific transmit data packet going across an RS-232 bus. A complete set of triggers, including triggers for specific serial packet content, ensures you quickly capture your event of interest. Discover - Fast waveform capture rate - over 250,000 wfm/s - maximizes the probability of capturing elusive glitches and other infrequent events. 2 www.tektronix.com To enable complex system debug and validation, the DPO7000C Series provides Pinpoint(R) triggering, using Silicon Germanium (SiGe) technology to provide trigger performance up to the bandwidth of the oscilloscope and over 1400 trigger combinations. Most other trigger systems offer multiple trigger types only on a single event (A event), with the delayed trigger (B event) selection limited to edge-type triggering, and often do not provide a way to reset the trigger sequence if the B event doesn't occur. But Pinpoint triggering provides a full suite of advanced trigger types on both A and B triggers with Reset triggering to begin the trigger sequence again after a specified time, state, or transition so that even events in the most complex signals can be captured. DPO7000C Series Datasheet - DPO7000C Series Finding the right characteristic of a complex signal can require hours of collecting and sorting through thousands of acquisitions for the event of interest. Defining a trigger that isolates the desired event and shows data only when the event occurs speeds up this process. The optional Visual Trigger makes the identification of the desired waveform events quick and easy by scanning through all waveform acquisitions and comparing them to on-screen areas (geometric shapes). With up to a 500 M point record length, you can capture many events of interest, even thousands of serial packets, in a single acquisition for further analysis while maintaining high resolution to zoom in on fine signal details. Investigate multiple segments of your waveform capture simultaneously with MultiView ZoomTM to quickly compare events in real time. FastFrameTM Segmented Memory mode enables you to make efficient use of large records by capturing many trigger events in a single record eliminating large time gaps between events of interest. View and measure the segments individually or as an overlay. From triggering on specific packet content to automatic decode in multiple data formats, the DPO7000C Series provides integrated support for a broad range of serial buses - I2C, SPI, CAN, LIN, FlexRay, RS-232/422/485/ UART, MIL-STD-1553, Ethernet, USB 2.0, and MIPI D-PHY. The ability to decode up to 16 serial buses simultaneously means you gain insight into system-level problems quickly. The DPO7000C Series offers the industry's most comprehensive search and waveform navigation with the standard Advanced Search and Mark feature and front-panel controls. User marks allow you to mark any location that you may want to reference later for further investigation. Or, automatically search your entire record for the criteria you define. Along the way it will automatically mark every occurrence of your defined event so you can quickly move between events. The advanced search and mark capability of the DPO7000C Series can search for up to eight different events simultaneously and stop a live acquisition when it finds an event of interest, saving even more time. Analyze Verifying that your prototype's performance matches simulations and meets the project's design goals requires analyzing its behavior. Tasks can range from simple checks of rise times and pulse widths to sophisticated power loss analysis, characterization of system clocks, and investigation of noise sources. The DPO7000C Series offers a comprehensive set of integrated analysis tools including waveform- and screen-based cursors, 53 automated measurements, advanced waveform math including arbitrary equation editing, custom MATLAB and .NET math plug-in analysis functions, waveform histograms, and FFT analysis. Search Finding your event of interest in a long waveform record can be time consuming without the right search tools. With today's record lengths pushing beyond a million data points, locating your event can mean scrolling through thousands of screens of signal activity. Analyze - Waveform histogram of a falling edge showing the distribution of edge position (jitter) over time. Included are numeric measurements made on the waveform histogram data. A comprehensive set of integrated analysis tools speeds verification of your design's performance. Search - Results of an advanced search for a runt pulse or a narrow glitch within a long waveform record. Each instance of the runt or glitch is automatically marked for easy reference. Every DPO7000C Series oscilloscope includes the DPOJET Essentials jitter and eye pattern analysis software package, extending the oscilloscope's measurement capabilities to make measurements over contiguous clock and data cycles in a single-shot real-time acquisition. This enables measurement of key jitter and timing analysis parameters such as Time Interval Error and Phase Noise to help characterize possible system timing issues. Analysis tools such as plots for time trends and histograms quickly show how timing parameters change over time, and spectrum analysis quickly shows the precise frequency and amplitude of jitter and modulation sources. Specialized application support for serial bus debug and compliance test, jitter and eye pattern analysis, power supply design, limit and mask testing, DDR memory bus analysis, and wideband RF is also available. www.tektronix.com 3 Datasheet Advanced search and mark A 12.5 M point standard record length represents thousands of screens of information. The DPO7000C Series enables you to find your event in seconds with Advanced Search and Mark. Search step 2: Advanced Search and Mark automatically searches through the record and marks each event with a solid colored triangle. You can then use the Previous and Next buttons to jump from one event to the next. Search step 1: You define what you would like to find. User marks Press the Set/Clear front-panel button to place one or more marks on the waveform. Navigating between marks is as simple as pressing the Previous () and Next () buttons on the front panel. Digital phosphor technology The DPO7000C Series' digital phosphor technology provides you with fast insight into the real operation of your device. Its fast waveform capture rate - greater than 250,000 wfm/s - gives you a high probability of quickly seeing the infrequent problems common in digital systems: runt pulses, glitches, timing issues, and more. Search marks The Search button allows you to automatically search through your long acquisition looking for user-defined events. All occurrences of the event are highlighted with search marks and are easily navigated to, using the frontpanel Previous () and Next () buttons. Search types include edge, glitch, width, timeout, runt, pattern, state, setup and hold, transition, and window. Digital phosphor technology enables greater than 250,000 wfm/s waveform capture rate and real-time color grading on the DPO7000C Series. Waveforms are superimposed with one another and waveform points are color coded by frequency of occurrence. This quickly highlights the events that occur more often over time or, in the case of infrequent anomalies, occur less often. With the DPO7000C Series, you can choose infinite persistence or variable persistence, determining how long the previous waveform acquisitions stay on-screen. This allows you to determine how often an anomaly is occurring. 4 www.tektronix.com DPO7000C Series Datasheet - DPO7000C Series Visual Trigger (Optional) - Find the signal of interest quickly Finding the right cycle of a complex bus can require hours of collecting and sorting through thousands of acquisitions for an event of interest. Defining a trigger that isolates the desired event speeds up debug and analysis efforts. Visual Trigger qualifies the Tektronix Pinpoint Triggers by scanning through all waveform acquisitions and comparing them to on-screen areas (geometric shapes). Up to eight areas can be created using a mouse or touchscreen, and a variety of shapes (triangles, rectangles, hexagons, or trapezoids) can be used to specify the desired trigger behavior. Once shapes are created, they can be edited interactively to create ideal trigger conditions By triggering only on the most important signal events, Visual Trigger can save hours of capturing and manually searching through acquisitions. In seconds or minutes, you can find the critical events and complete your debug and analysis efforts. DDR memory bus events involve clocks, strobes and data channels as well as multiple amplitudes and bursts of data. Visual Trigger extends the Tektronix oscilloscope's triggering capabilities for a wide variety of complex signals as illustrated by the examples shown here. DDR memory. Visual Trigger used to isolate a rare occurrence of a write burst on a specific bit pattern in DDR3. The trigger event is a Write DQ burst of 11000000, when the DQ launch starts from a non-tri-state voltage value. DDR memory bus events involve clocks, strobes and data channels as well as multiple amplitudes and bursts of data. Customized serial triggering. Visual Trigger set to find a serial data pattern of 1101 0101. Boolean logic trigger qualification. Boolean logic using logical OR allows the user to simultaneously monitor each bit and capture the occurrence of an anomaly at any point in the acquisition. Multiple channel triggering. Visual Trigger areas can be associated with events spanning multiple channels such as packets transmitted on two USB2.0 buses simultaneously. www.tektronix.com 5 Datasheet Trigger on the width of a burst of 10 pulses. By drawing a "Must be outside" area before the first clock pulse and a second "Must be outside" area after the tenth pulse, as shown, you can define a Visual Trigger setup that captures the desired burst width. Triggering on a specific OUT Token packet on a USB full-speed serial bus. A bus waveform provides decoded packet content including Start, Sync, PID, Address, End Point, CRC, Data values, and Stop. Bus display Serial triggering and analysis (optional) On a serial bus, a single signal often includes address, control, data, and clock information. This can make isolating events of interest difficult. The DPO7000C Series offers a robust set of tools for debugging serial buses with automatic trigger and decode on I2C, SPI, CAN, LIN, FlexRay, RS-232/422/485/UART, MIL-STD-1553, and USB 2.0, and decode for MIPI D-PHY DSI-1 and CSI-2, 8b/10b, Ethernet, and PCI Express serial buses. Serial triggering Trigger on packet content such as start of packet, specific addresses, specific data content, unique identifiers, etc. on popular serial interfaces such as I2C, SPI, CAN, LIN, FlexRay, RS-232/422/485/UART, MILSTD-1553, and USB 2.0. Provides a higher-level, combined view of the individual signals (clock, data, chip enable, etc.) that make up your bus, making it easy to identify where packets begin and end and identifying subpacket components such as address, data, identifier, CRC, etc. Bus decoding Tired of having to visually inspect the waveform to count clocks, determine if each bit is a 1 or a 0, combine bits into bytes, and determine the hex value? Let the oscilloscope do it for you! Once you've set up a bus, the DPO7000C Series will decode each packet on the bus, and display the value in hex, binary, decimal (USB only) or ASCII (USB and RS-232/422/485/UART only) in the bus waveform. Event table display In addition to seeing decoded packet data on the bus waveform itself, you can view all captured packets in a tabular view much like you would see in a software listing. Packets are time stamped and listed consecutively with columns for each component (Address, Data, etc.). 6 www.tektronix.com DPO7000C Series Datasheet - DPO7000C Series Event table showing decoded serial packet data in a long acquisition. USB 2.0 Compliance Testing. Bus searching Power analysis (optional) Serial triggering is very useful for isolating the event of interest, but once you've captured it and need to analyze the surrounding data, what do you do? In the past, users had to manually scroll through the waveform counting and converting bits and looking for what caused the event. With the DPO7000C Series, you can have the oscilloscope automatically search through the acquired data for user-defined criteria including serial packet content. Each occurrence is highlighted by a search mark. Rapid navigation between marks is as simple as pressing the Previous () and Next () buttons on the front panel. The optional power analysis software package (Option PWR) enables quick and accurate analysis of power quality, switching loss, harmonics, magnetic measurements, safe operating area (SOA), modulation, ripple, and slew rate (di/dt, dv/dt). Automated, repeatable power measurements are available with a touch of a button; no external PC or complex software setup is required. The package includes a report generation tool to create customizable, detailed reports to document your measurement results. Serial bus compliance test (optional) Software packages for automated compliance test are available for MIPI DPHY (Option D-PHY), Ethernet 10BASE-T, 10BASE-Te, 100BASE-TX, and 1000BASE-T (Option ET3), MOST50 and MOST150 electrical (Option MOST), and USB 2.0 (Option USB) physical-layer devices. These software packages enable you to conduct testing using the standard's specified compliance tests. Switching Loss measurements. Automated power measurements enable quick and accurate analysis of common power parameters. www.tektronix.com 7 Datasheet Advanced analysis jitter timing and eye diagram measurements (optional) The optional DPOJET Advanced software package (Option DJA) offers extended capabilities, providing a complete suite of analysis tools for insight into jitter and timing as well as other signal quality issues. DPOJET Advanced adds advanced tools such as Rj/Dj separation, eye diagram masks, and Pass/Fail limits for conformance testing. The innovative onetouch wizard makes setup for jitter measurements easy. DPOJET Advanced is also a measurement framework that works in conjunction with standardsspecific compliance test packages for applications such as DDR memory and USB. Mask testing an OC-12 signal, capturing any violations of the mask. DDR memory bus analysis (optional) Advanced analysis, jitter, eye diagram, and timing measurements. Limit and mask testing (optional) The optional limit test (Option LT) and mask test (Option MTM) software packages are useful for long-term signal monitoring, characterizing signals during design, and testing on a production line. The limit test software compares a tested signal to a known good or "golden" version of the same signal with user-defined vertical and horizontal tolerances. The mask test software includes a robust set of masks for telecommunications and computer standards for easily checking compliance to a standard. Additionally, custom masks can be created and used for characterizing signals. With both software packages you can tailor a test to your specific requirements by defining test duration in a number of waveforms, setting a violation threshold that must be met before considering a test a failure, counting hits along with statistical information, and setting actions upon violations, test failure, and test complete. Whether specifying a limit template or a mask, conducting pass/fail tests in search of waveform anomalies such as glitches has never been easier. 8 www.tektronix.com The optional DDR memory analysis software package (Option DDRA) automatically identifies DDR1, DDR2, DDR3, LP-DDR, LP-DDR2, and GDDR3 Reads and Writes and makes JEDEC conformance measurements with Pass/Fail results on all edges in every Read and Write burst, perfect for debugging and troubleshooting DDR memory buses. Also provided are common measurements of clock, address, and control signals. Used in conjunction with DPOJET (Option DJA), Option DDRA is the fastest way to debug complex memory signaling issues. Vector signal analysis (optional) The optional SignalVuTM vector signal analysis packages (Options SVE, SVA, SVM, SVO, SVP, and SVT) easily validate wideband designs and characterize wideband spectral events. By combining the signal analysis engine of Tektronix real-time spectrum analyzers with the wide bandwidth acquisition of Tektronix digital oscilloscopes, you can now evaluate complex baseband signals directly on your oscilloscope. You get the functionality of a vector signal analyzer, a spectrum analyzer, and the powerful trigger capabilities of a digital oscilloscope - all in a single package. Whether your design validation needs include wideband radar, high data-rate satellite links, or frequency-hopping communications, SignalVuTM vector signal analysis software can speed your time-to-insight by showing you timevariant behavior of these wideband signals. DPO7000C Series Datasheet - DPO7000C Series TekVPI(R) probe interface The TekVPI probe interface sets the standard for ease of use in probing. TekVPI probes feature status indicators and controls, as well as a probe menu button right on the probe itself. This button brings up a probe menu on the oscilloscope display with all relevant settings and controls for the probe. The TekVPI interface enables direct attachment of a current probe without requiring a separate power supply. TekVPI probes can be controlled remotely through USB, GPIB, or Ethernet, enabling more versatile solutions in ATE environments. MyScope(R) custom control window SignalVuTM enables detailed analysis in multiple domains. Designed to make your work easier Easily create your own personalized "toolbox" of oscilloscope features in a matter of minutes using a simple, visual, drag-and-drop process. Once created, these custom control windows are easily accessed through a dedicated MyScope menu selection on the oscilloscope. This is ideal in a shared resource environment where each person can have their own custom control interface suited to their particular use. MyScope control windows benefit all oscilloscope users, eliminating the ramp-up time that many face when returning to the lab after not using an oscilloscope for a while, and enabling power users to be far more efficient. Large high-resolution display The DPO7000C Series features a 12.1 in. (307 mm) XGA color display with an integrated touch screen for seeing intricate signal details. Dedicated fron-panel controls Per-channel vertical controls provide simple and intuitive operation. No longer do you need to share one set of vertical controls across all four channels. Connectivity USB 2.0 host ports on the front and side panels enable easy transfer of screenshots, instrument settings, and waveform data to a USB thumb drive. The rear panel contains a GPIB port for controlling the oscilloscope remotely from a computer. An integrated 10/100/1000BASE-T Ethernet port enables easy connection to networks and a Video Out port allows the oscilloscope display to be exported to an external monitor or projector. PS-2 ports for keyboard and mouse are included for security-conscious applications that require the USB ports to be disabled. A standard removable hard disk drive makes customizing settings for different users easy as well as enables use in secure environments. MyScope custom control windows are created with a simple drag-and-drop process enabling each user to have a unique interface. Floating licenses Floating licenses offer an alternative method to manage your Tektronix asset. Floating licenses allow license-key enabled options to be easily moved among all your MSO/DPO5000, DPO7000, and DPO/DSA/ MSO70000 Series of Tektronix oscilloscopes. Floating licenses are available for many license-key enabled options. To order a floating version of an option license add "DPOFL-" prefix to the option name. (e.g. DPOFLET3) Check www.tektronix.com for additional information about floating license options. www.tektronix.com 9 Datasheet Interoperability with logic analyzer The Tektronix Integrated View (iViewTM) data display enables digital designers to solve signal integrity challenges and effectively debug and verify their systems more quickly and easily. This integration allows designers to view time-correlated digital and analog data in the same display windows, and isolate the analog characteristics of the digital signals that are causing system failures. No user calibration is required. And, once set up, the iView feature is completely automated. Remote operation and extended analysis There are many ways to connect to your DPO7000C Series oscilloscope to conduct extended analysis. The first makes use of the Windows Remote Desktop capability - connect directly to your oscilloscope and operate the user interface remotely through the built-in Remote Desktop. A second way to connect is through Tektronix OpenChoice(R) software which makes use of the fast embedded bus, transferring waveform data directly from acquisition to analysis applications on the Windows desktop at much faster speeds than conventional GPIB transfers. Industry-standard protocols, such as TekVISATM interface and ActiveX controls are included for using and enhancing Windows applications for data analysis and documentation. IVICOM instrument drivers are included to enable easy communication with the oscilloscope using GPIB, serial data, and LAN connections from programs running on the instrument or an external PC. Or, use the Software Developer's Kit (SDK) to help create custom software to automate multistep processes in waveform collection and analysis with Visual BASIC, C, C++, MATLAB, LabVIEW, LabWindows/CVI, and other common Application Development Environments (ADE). Microsoft(R) Excel and Word toolbars are included to simplify data capture and transfer directly to these programs running on the Windows desktop. A third way to connect to your oscilloscope is through NI LabVIEW SignalExpress Tektronix Edition, enabling you to instantly acquire, generate, analyze, compare, import, and save measurement data and signals using an intuitive drag-and-drop user interface that does not require any programming. Capture data into Microsoft Excel using the unique Excel toolbar, and create custom reports using the Word toolbar. Specifications All specifications apply to all models unless noted otherwise. Model overview DPO7054C DPO7104C DPO7254C DPO7354C 500 MHz 1 GHz 2.5 GHz 3.5 GHz Rise Time 10% to 90% (Typical) 460 ps 300 ps 160 ps 115 ps Rise Time 20% to 80% (Typical) 310 ps 200 ps 100 ps 95 ps DC Gain Accuracy 1% with offset/position set to 0 Bandwidth Limits Depending on instrument model: 3.0 GHz, 2.5 GHz, 2 GHz, 1 GHz, 500 MHz, 250 MHz, and 20 MHz Input Channels 4 Bandwidth Effective Number of Bits (Typical, sine 6.8 bits wave input at instrument bandwidth, 50 mV/div, 50 Input Impedance, maximum sample rate, 20k point record length) 6.7 bits Random Noise (RMS, typical, sample mode, full BW, maximum sample rate) 10 www.tektronix.com 5.6 bits 5.6 bits DPO7000C Series Datasheet - DPO7000C Series Step Gain DPO7054C DPO7104C DPO7254C DPO7354C 500 mV 11.9 mV 13.2 mV 19.7 mV 23.5 mV 200 mV 5.0 mV 5.57 mV 8.71 mV 10.9 mV 100 mV 2.75 mV 3.27 mV 5.23 mV 6.6 mV 50 mV 1.2 mV 1.36 mV 2.0 mV 2.35 mV 20 mV 0.5 mV 0.574 mV 0.866 mV 1.03 mV 10 mV 0.28 mV 0.328 mV 0.523 mV 0.61 mV 5 mV 0.185 mV 0.229 mV 0.343 mV 0.41 mV 2 mV 0.11 mV 0.135 mV 0.135 mV 0.19 mV 1 mV 0.09 mV 0.095 mV 0.095 mV 0.12 mV DPO7054C DPO7104C DPO7104C with Option 2SR DPO7254C/DPO7354C Maximum Sample Rate (1 ch) 20 GS/s 20 GS/s 40 GS/s 40 GS/s Maximum Sample Rate (2 ch) 10 GS/s 10 GS/s 20 GS/s 20 GS/s Maximum Sample Rate (3-4 ch) 5 GS/s 5 GS/s 10 GS/s 10 GS/s Maximum Equivalent Time Sampling Rate 4 TS/s Maximum Record Length with Standard Configuration 50 M (1 ch), 25 M (2 ch), 12.5 M (3-4 ch) -- 500 M (1 ch) 250 M (2 ch) 125 M (3-4 ch) Maximum Record Length with Option 125 M (1 ch), 50 M (2 ch), 25 M (3-4 ch) 2RL Maximum Record Length with Option 250 M (1 ch), 125 M (2 ch), 50 M (3-4 ch) 5RL Maximum Record Length with Option -- 10RL -- Maximum Duration at Highest Realtime Sample Rate (1 ch) 1-2 ms with standard record length, up to 10 ms with optional record length Time Base Range 1.25 ps/div to 1000 s/div 1.25 ps/div to 1000 s/div 1.25 ps/div to 1000 s/div 1.25 ps/div to 1000 s/div Time Resolution (in ET/IT mode) 500 fs 500 fs 250 fs 250 fs Vertical system - Analog channels Input impedance 1 M 1% with 13 pF 2 pF, 50 1% Input coupling AC, DC, GND Input sensitivity 1 M: 1 mV/div to 10 V/div 50 : 1 mV/div to 1 V/div Vertical resolution 8 bit (>11 bit with Hi Res) Delay between any two channels, typical 100 ps (50 , DC coupling and equal V/div at or above 10 mV/div) Channel-to-Channel isolation (Any two channels at equal Vertical Scale settings) (Typical) 100:1 at 100 MHz 30:1 between 100 MHz and 2.5 GHz 20:1 between 2.5 GHz and 3.5 GHz Max input voltage 1 M 150 V, derate at 20 dB/decade to 9 VRMS above 200 kHz Max input voltage 50 5 VRMS, with peaks 24 V www.tektronix.com 11 Datasheet Offset range 1 mV/div to 50 mV/div: 1 V 50.5 mV/div to 99.5 mV/div: (1.5 V - 10 divisions) 100 mV/div to 500 mV/div: 10 V 505 mV/div to 995 mV/div: (15 V - 10 divisions) 1 V/div to 5 V/div: 100 V 5.05 V/div to 10 V/div: (150 V - 10 divisions) Offset accuracy 1 mV/div to 9.95 mV/div: 0.2% x (offset - position) 0.1 div 1.5 mV 10 mV/div to 99.5 mV/div: 0.35% x (offset - position) 0.1 div 1.5 mV 100 mV/div to 1 V/div: 0.35% x (offset - position) 0.1 div 15 mV 1.01 V/div to 10 V/div: 0.25% x (offset - position) 0.1 div 150 mV Position range 5 divisions Horizontal system Time base delay time range -10 divisions to 1000 s Channel-to-channel deskew range 75 ns Delta time measurement accuracy ((0.06 / sample rate) + (2.5 ppm x Reading)) RMS Trigger jitter (RMS) 1.5 psRMS with enhanced triggering OFF <100 fsRMS with enhanced triggering ON Jitter noise floor <1 psRMS (<2 psPeak) for record duration <10 s (typical) <2.5 psRMS for record duration <30 ms <65 parts/trillion for record durations <10 s Time base accuracy 2.5 ppm + aging <1 ppm per year Acquisition system Acquisition modes Sample Acquires and displays sampled values Peak detect Captures and displays narrow glitches at all real-time sampling rates. Glitch widths: 1 ns at 10 GS/s Averaging From 2 to 10,000 waveforms can be included in an average waveform Envelope From 1 to 2x109 waveforms included in min-max envelope Hi-Res Real-time boxcar averaging reduces random noise and increases resolution Roll mode Scrolls sequential waveform points across the display in a right-to-left rolling motion at sweep speeds slower than 50 ms/div. Works at sample rates up to 10 MS/s with a maximum record length of 40 MS FastAcqTM FastAcqTM optimizes the instrument for analysis of dynamic signals and capture of infrequent events, capturing >250,000 wfms/s on all 4 channels simultaneously Waveform database Accumulates waveform data providing a three-dimensional array of amplitude, time, and counts FastFrameTM Acquisition memory divided into segments; maximum trigger rate >310,000 waveforms per second. Time of arrival recorded with each event. Frame finder tool helps to visually identify transients 12 www.tektronix.com DPO7000C Series Datasheet - DPO7000C Series Pinpoint(R) trigger system Trigger sensitivity Internal DC coupled 0.7 div from DC to 50 MHz, increasing to 1.2 div at rated analog bandwidth (typical), up to 2.5 GHz. 2.5 div at 3.5 GHz Aux input (external trigger) 1 M 250 mV from DC to 50 MHz, increasing to 350 mV at 250 MHz (typical) Trigger delay by time 3.2 ns to 3,000,000 s Trigger delay by events 1 to 2,000,000,000 events Main trigger modes Auto, Normal, and Single Enhanced triggering Enhanced triggering corrects the difference in timing between the trigger path and the acquired data path (supports all Pinpoint trigger types on both A- and B-Events except pattern trigger); Default On (user-selectable); Not available in FastAcq mode. Trigger sequences Main, Delayed by Time, Delayed by Events, Reset by Time, Reset by State, Reset by Transition, B Event Scan. All sequences can include separate horizontal delay after the trigger event to position the acquisition window in time. Communications-related triggers Support for AMI, HDB3, BnZS, CMI, MLT3, and NRZ encoded communications signals. Select among isolated positive or negative one, zero pulse form, or eye patterns as applicable to the standard. Requires Option MTM . Video trigger formats and field rates Triggers from negative sync composite video, field 1 or field 2 for interlaced systems, any field, specific line, or any line for interlaced or noninterlaced systems. Supported systems include NTSC, PAL, SECAM, and HDTV 1080/24sF, 1080p/25, 1080i/50, 1080i/60, 1080p/24, 720p/60, 480p/60 Serial pattern trigger NRZ-Encoded Data Clock recovery system DPO7254C and DPO7354C only, requires Opt. ST1G. Up to 64 bit serial word recognizer, bits specified in binary (high, low, don't care) or hex format. Trigger on NRZ-encoded data up to 1.25 GBaud. (DPO7254C and DPO7354C only, requires Opt. ST1G or MTM) Clock recovery phase locked loop bandwidth Fixed at FBaud/500 Clock recovery frequency range 1.5 MBaud to 1.25 GBaud Clock recovery jitter (RMS) 20 psRMS + 1.25% Unit Interval RMS for PRBS data patterns 20 psRMS + 1.25% Unit Interval RMS for repeating "0011" data pattern Clock recovery tracking/ acquisition range 5% of requested baud rate (typical) Minimum signal amplitude needed for clock recovery 1 divp-p up to 1.25 Gbaud Trigger level range Any channel 12 divisions from center of screen Auxiliary input TekVPI interface; 5 V (50 ); 150 V, derate at 20 dB/decade to 9 VRMS above 200 kHz (1 M) Line Fixed at 0 V Trigger coupling DC AC (attenuates <60 Hz) HF Rej (attenuates >30 kHz) LF Rej (attenuates <80 kHz) Noise Reject (reduces sensitivity) Trigger holdoff range 250 ns min to 100 s www.tektronix.com 13 Datasheet Trigger types A Event and Delayed B Event trigger types: edge, glitch, width, runt, timeout, transition time, logic pattern, logic state, setup/hold, window - all except Edge, Pattern, and State can be Logic State qualified by up to two channels. Edge Positive or negative slope on any channel or front-panel auxiliary input. Coupling includes DC, AC, noise reject, HF reject, and LF reject. Glitch Trigger on or reject glitches of positive, negative, or either polarity. Minimum glitch width is 170 ps (typical) with rearm time of 250 ps (for DPO7254C or DPO7354C) Width Trigger on width of positive or negative pulse either within or outside of selectable limits (225 ps to 10 s) Runt Trigger on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first again. Event can be time- or logic-qualified. Window Trigger on an event that enters or exits a window defined by two user-adjustable thresholds. Event can be time or logic qualified. Timeout Trigger on an event which remains high, low, or either, for a specified time period (300 ps to 1 s) Transition Trigger on pulse edge rates that are faster or slower than specified. Slope may be positive, negative, or either. Setup/Hold Trigger on violations of both setup time and hold time between clock and data present on any two input channels. Logic Pattern Trigger when pattern goes false or stays true for specified period of time (300 ps to 1 s). Pattern (AND, OR, NAND, NOR) specified for all analog input channels defined as high, low, or don't care Logic State Any logical pattern of channels (1, 2, 3) clocked by edge on channel 4. Trigger on rising or falling clock edge. Parallel Bus Trigger on specified data value on defined parallel bus Video Trigger on all lines, specific line number, odd, even, or all fields on NTSC, PAL, SECAM, and HDTV 480p/60, 576p/50, 875i/60, 720p/30, 720p/50, 720p/60, 1080/24sF, 1080i/50, 1080p/25, 1080i/60, 1080p/24, 1080p/25, 1080p/50, 1080p/60, Bi-level, Tri-level Optional trigger types Visual Trigger Trigger on up to 8 user-specified areas, including rectangle, triangle, trapezoid, hexagon, and user-specified shapes on any of the analog channels. Provided as part of Opt. VET. Serial Pattern Captures serial data stream with built-in clock recovery for NRZ standards up to 1.25 Gb/s. Extended with pattern lock triggering to capture repeated acquisitions of long serial data patterns. Provided as part of Opt. ST1G. Comm Support for AMI, HDB3, BnZS, CMI, MLT3, and NRZ encoded signals. Provided as part of Option MTM. I2C Trigger on Start, Repeated Start, Stop, Missing ACK, Address (7 or 10 bit), Data (1-5 bytes), or Address and Data on I2C buses up to 10 Mb/s. Provided as part of Opt. SR-EMBD. SPI Trigger on Slave Select, Idle Time, or Data (1-6 words) on SPI buses up to 10 Mb/s. Provided as part of Opt. SR-EMBD. CAN Trigger on Start of Frame, Frame Type (Data, Remote, Error, or Overload), Identifier, Data, Identifier and Data, End of Frame, Missing Ack, Bit Stuff Error or CRC Error on CAN buses up to 1 Mb/s. Provided as part of Opt. SR-AUTO. LIN Trigger on Sync, Identifier, Data, Ident and Data, Wakeup Frame, Sleep Frame, and Error on LIN buses up to 1 Mb/s. Provided as part of Opt. SR-AUTO. FlexRay Trigger on Indicator Bits (Normal, Payload, Null, Sync, Startup), Cycle Count, Header Fields (Indicator Bits, Identifier, Payload Length, Header CRC, and Cycle Count), Identifier, Data, Identifier and Data, End Of Frame, and Error on FlexRay buses up to 10 Mb/s. Provided as part of Opt. SR-AUTO. MIL-STD-1553B Trigger on Sync, Command Word, Status Word, Data Word, Idle Time, and Error on MIL-STD-1553 buses up to 1 Mb/s. Provided as part of Opt. SR-AERO. RS-232/422/485/UART Trigger on Start Bit, End of Packet, Data (1-5 words), and Parity Error on RS-232 buses up to 10 Mb/s. Provided as part of Opt. SRCOMP. USB 2.0 Low speed Trigger on Sync, Reset, Suspend, Resume, End of Packet, Token (Address) Packet, Data Packet, Handshake Packet, Special Packet, Error. Provided as part of Opt. SR-USB. Token Packet Trigger - Any token type, SOF, OUT, IN, SETUP; Address can be specified for Any, OUT, IN, and SETUP token types. Address can be further specified to trigger on , <, =, >, , != a particular value, or inside or outside of a range. Frame number can be specified for SOF token using Binary, Hex, Unsigned Decimal, and Don't Care digits. Data Packet Trigger - Any data type, DATA0, DATA1; Data can be further specified to trigger on , <, =, >, , != a particular data value, or inside or outside of a range. Handshake Packet Trigger - Any handshake type, ACK, NAK, STALL. Special Packet Trigger - Any special type, Reserved. Error Trigger - PID Check, CRC5 or CRC16, Bit Stuffing. 14 www.tektronix.com DPO7000C Series Datasheet - DPO7000C Series USB 2.0 Full speed Trigger on Sync, Reset, Suspend, Resume, End of Packet, Token (Address) Packet, Data Packet, Handshake Packet, Special Packet, Error. Provided as part of Opt. SR-USB. Token Packet Trigger - Any token type, SOF, OUT, IN, SETUP; Address can be specified for Any, OUT, IN, and SETUP token types. Address can be further specified to trigger on , <, =, >, , != a particular value, or inside or outside of a range. Frame number can be specified for SOF token using Binary, Hex, Unsigned Decimal, and Don't Care digits. Data Packet Trigger - Any data type, DATA0, DATA1; Data can be further specified to trigger on , <, =, >, , != a particular data value, or inside or outside of a range. Handshake Packet Trigger - Any handshake type, ACK, NAK, STALL. Special Packet Trigger - Any special type, PRE, Reserved. Error Trigger - PID Check, CRC5 or CRC16, Bit Stuffing. USB 2.0 High speed No protocol-level triggering. Provided as part of Opt. SR-USB. USB 2.0 High speed decoding and search only available on 1 GHz models. Waveform analysis Search and Mark Events Use Advanced Search and Mark to automatically mark events and document waveforms. Search positive/negative slopes or both, glitches, runts, pulse widths, transition rate, setup and hold, timeout, windows, or find any logic or state pattern, up to 8 different event types on any of the 4 analog channels. Search DDR Read or Write bursts with Opt. DDRA. When an event of interest is found with a hardware trigger, other similar events can be found using "Mark All Trigger Events in Record" in the Pinpoint trigger control windows. The Event table summarizes all found events. All events are time stamped in reference to trigger position. You can choose to stop acquisitions when an event is found. Waveform measurements Cursors Waveform and Screen Automatic measurements 53, of which 8 can be displayed on-screen at any one time Measurement Statistics Mean, Minimum, Maximum, Standard Deviation Reference Levels User-definable reference levels for automatic measurements can be specified in either percent or units Gating Isolate the specific occurrence within an acquisition to take measurements on, using either screen or waveform cursors Amplitude related Amplitude, High, Low, Maximum, Minimum, Peak-to-Peak, Mean, Cycle Mean, RMS, Cycle RMS, Positive Overshoot, Negative Overshoot Time related Rise Time, Fall Time, Positive Width, Negative Width, Positive Duty Cycle, Negative Duty Cycle, Period, Frequency, Delay Combination Area, Cycle Area, Phase, Burst Width Histogram related Waveform Count, Hits in Box, Peak Hits, Median, Maximum, Minimum, Peak-to-Peak, Mean (), Standard Deviation (sigma), +1sigma, +2sigma, +3sigma Eye-pattern related Extinction Ratio (absolute, %, dB), Eye Height, Eye Width, Eye Top, Eye Base, Crossing %, Jitter (p-p, RMS, 6sigma), Noise (p-p, RMS), Signal/Noise Ratio, Cycle Distortion, Q-Factor Waveform Histograms A waveform histogram provides an array of data values representing the total number of hits inside of a user-defined region of the display. A waveform histogram is both a visual graph of the hit distribution as well as a numeric array of values that can be measured. Sources - Channel 1, Channel 2, Channel 3, Channel 4, Ref 1, Ref 2, Ref 3, Ref 4, Math 1, Math 2, Math 3, Math 4 Types - Vertical, Horizontal Waveform processing/math Number of Math Waveforms Up to 4 Arithmetic Add, Subtract, Multiply, Divide Waveforms and Scalars Algebraic expressions Define extensive algebraic expressions including waveforms, scalars, user-adjustable variables, and results of parametric measurements. Perform math on math using complex equations. e.g. (Integral (CH1 - Mean(CH1)) x 1.414 x VAR1) Math functions Average, Invert, Integrate, Differentiate, Square Root, Exponential, Log 10, Log e, Abs, Ceiling, Floor, Min, Max, Sin, Cos, Tan, ASin, ACos, ATan, Sinh, Cosh, Tanh Relational Boolean result of comparison >, <, , , ==, != Frequency domain functions Spectral Magnitude and Phase, Real and Imaginary Spectra www.tektronix.com 15 Datasheet FFT vertical units Magnitude: Linear, dB, dBm Phase: Degrees, radians, group delay FFT window functions Rectangular, Hamming, Hanning, Kaiser-Bessel, Blackman-Harris, Gaussian, Flattop2, Tek Exponential Waveform definition As an arbitrary math expression Filtering function User-definable filters. Users specify a file containing the coefficients of the filter. Several example filter files are provided Customized Functions using Math Plug-in Interface An interface is provided to allow users to create their own custom math functions in MATLAB or Visual Studio Mask function Generates a Waveform Database pixel map from a sample waveform. Sample count can be defined Software NI LabVIEW SignalExpress Tektronix Edition A fully interactive measurement software environment optimized for the DPO7000C Series enables you to instantly acquire, generate, analyze, compare, import, and save measurement data and signals using an intuitive drag-and-drop user interface that does not require any programming. Standard DPO7000C Series support for acquiring, controlling, viewing, and exporting your live signal data is permanently available through the software. The full version (SIGEXPTE) adds additional signal processing, advanced analysis, mixed signal, sweeping, limit testing, and user-defined step capabilities and is available for a 30-day trial period. IVI Driver Provides a standard instrument programming interface for common applications such as LabVIEW, LabWindows/CVI, Microsoft .NET and MATLAB. IVI-COM standard LXI Class C Web Interface Connect to the DPO7000C Series through a standard web browser by simply entering the oscilloscope's IP address in the address bar of the browser. The web interface enables viewing of instrument status and configuration, as well as status and modification of network settings. All web interaction conforms to LXI Class C specification Display system Display type 307.3 mm (12.1 in.) liquid-crystal active-matrix color display Display resolution 1024 horizontal x 768 vertical pixels (XGA) Waveform styles Vectors, Dots, Variable Persistance, Infinite Persistance Color palettes Normal, Green, Gray, Temperature, Spectral, and User-defined Format YT, XY Horizontal divisions 10 Vertical divisions 10 Computer system and peripherals Operating system Windows 7 Ultimate 64-bit Instrument operation verified with version 1.1 of the National Institute of Standards and Technology (NIST) DSS Baseline Requirements, also known as the United States Government Configuration Baseline (USGCB) CPU Intel Core 2 Duo, 3 GHz processor System memory 8 GB Hard disk drive Removable hard disk drive, 500 GB capacity (3.5 in. SATA) CD/DVD drive Front-panel CD-R/W, DVD-R drive Mouse Optical wheel mouse, USB interface Keyboard Order 119-7083-xx for small keyboard; USB interface and hub 16 www.tektronix.com DPO7000C Series Datasheet - DPO7000C Series Input/Output ports USB 2.0 High-speed Host Ports Supports USB mass storage devices, printers, keyboard, and mouse. Ports on front and side panels of the instrument. Can be disabled individually GPIB interface Rear panel. IEEE 488.2 standard LAN port RJ-45 connector, supports 10BASE-T, 100BASE-T, and 1000BASE-T Video out port DVI-I connector, connect to show the oscilloscope display on an external monitor or projector. Support for extended desktop and clone mode Audio input/output Miniature phone jacks for stereo microphone input and stereo line output Keyboard port PS/2 compatible Mouse port PS/2 compatible Auxiliary input Front panel. See trigger specifications Auxiliary Out (Software switchable) Trigger Out: A TTL compatible pulse when the oscilloscope triggers External time base reference in Time base system can phase lock to an external 10 MHz reference (10 MHz 1%) Analog Signal Output BNC connector provides a buffered version of the Ch3 signal. 50 mV/div 20% into a 1 M load, 25 mV/div 20% into a 50 load. Bandwidth is 100 MHz into a 50 load Probe compensator output Front-panel pins Time Base Reference Out: A TTL compatible output of internal 10 MHz reference oscillator Amplitude: 1 V 20% into a 50 load Frequency: 1 kHz 5% Recovered Clock (DPO7254C and DPO7354C only) (Enabled by Opt. MTM.) BNC connector, 1.25 Gb/s, output swing 130 mVp-p into 50 Recovered Data (DPO7254C and DPO7354C only) (Enabled by Opt. MTM.) BNC connector, 1.25 Gb/s, output swing 200 mV into 50 LXI web interface (LAN eXtensions Class: LXI Class C Version: 1.3 for instrumentation) Power source Power Source 100 to 240 V 10%, 47 to 63 Hz, <550 W 115 VRMS 10%, 360 to 440 Hz, <500 VA Physical characteristics Dimensions Rackmount dimensions mm in. Height 292 11.48 Width 451 17.75 Depth 265 10.44 Height 331 12.25 Width 479 18.85 Depth (from rack mounting ear to back of instrument) 231.75 9.12 www.tektronix.com 17 Datasheet Weight Rackmount weight kg lb. Net 15 32 Shipping 28.9 63.75 Net 17.4 37.5 Kit 2.5 5.5 Cooling - Required clearance mm in. Top 0 0 Bottom 0 0 Left Side 76 3 Right Side 0 0 Front 0 0 Rear 0 0 Environmental Temperature Operating +5 C to +45 C, with noncondensing conditions Nonoperating -40 C to +71 C, with 15 C/hour maximum gradient, without CD/DVD media installed in disk drive Humidity Operating 8% to 80% relative humidity (RH) with a maximum wet bulb temperature of 29 C at or below +45 C, noncondensing. Upper limit derated to 30% RH at +45 C Nonoperating 5% to 90% relative humidity (RH) with a maximum wet bulb temperature of 29 C at or below +60 C, noncondensing. Upper limit derated to 20% RH at +60 C Altitude Operating 3,000 m (9,843 ft.) Nonoperating 12,192 m (40,000 ft.) Regulatory Electromagnetic compatibility 2004/108/EC Certifications UL61010-1; CSA61010-1, EN61010-1; IEC 61010-1 United States Government Configuration Baseline (USGCB) Testing 18 www.tektronix.com Tektronix has tested the DPO7000 Series oscilloscopes for compatibility with the security configuration for Information Technology products specified in the USGCB settings for Windows 7 and Internet Explorer DPO7000C Series Datasheet - DPO7000C Series Ordering information DPO7000C models DPO7054C 500 MHz, 5/10/20 GS/s (4/2/1 ch), 12.5 M record length, 4-channel digital phosphor oscilloscope DPO7104C 1 GHz, 5/10/20 GS/s (4/2/1 ch), 12.5 M record length, 4-channel digital phosphor oscilloscope DPO7254C 2.5 GHz, 10/20/40 GS/s (4/2/1 ch), 12.5 M record length, 4-channel digital phosphor oscilloscope DPO7354C 3.5 GHz, 10/20/40 GS/s (4/2/1 ch), 12.5 M record length, 4-channel digital phosphor oscilloscope Standard accessories P6139B One passive voltage probe per analog channel (500 MHz, 10X, 8 pF) -- Front cover 013-0347-00 DVI to VGA Adapter 071-298x-xx User Manual (please specify language when ordering) -- GPIB programmer's reference PDF file -- Performance verification procedure PDF file -- Advanced Search and Mark, DPOJET Essentials, and SR-CUST Custom serial analysis kit for developers software all included standard -- Accessory pouch -- Mouse -- Calibration Certificate documenting measurement traceability to National Metrology Institute(s), Z 540-1 Compliance and ISO9001 -- Power Cord (please specify power plug option when ordering) -- One-year warranty Instrument options Record length options Opt. 2RL 125 M max, 25 M/ch Opt. 5RL 250 M max, 50 M/ch Opt. 10RL 500 M max, 125 M/ch (DPO7254C and DPO7354C) Sample rate options Opt. 2SR Double maximum real-time sample rate to 40/20/10 GS/s on 1/2/4 ch (DPO7104C only) Storage options Opt. SSD Solid State Hard Disk Drive, 300 GB www.tektronix.com 19 Datasheet Advanced analysis options 20 www.tektronix.com Option Description Opt. DDRA DDR Memory Bus Analysis (Requires Opt. DJA) (For models of bandwidth 1 GHz only) Opt. DJA Jitter and Eye Analysis Tools - Advanced (DPOJET) Opt. D-PHY MIPI(R) D-PHY Essentials - Transmitter Debug,Characterization, and Compliance Test Solution (Requires Opt. DJA) (For models of bandwidth 2.5 GHz only) Opt. ET3 Ethernet Compliance Test Software (Requires TF-GBE-BTP or TF-GBE-ATP Ethernet Test Fixture) Opt. HSIC USB HSIC protocol decode and electrical validation (For models of bandwidth 2.5 GHz only.) Opt. LSA Low-speed Automotive Serial Analysis Bundle, includes CAN Trigger, CAN/LIN Decode and Analysis (includes TDSVNM) Opt. LT Waveform Limit Testing Opt. MOST Electrical Compliance and Debug Test Solution for MOST50 and MOST150 (Requires Opt. DJA) Opt. MTM Mask Testing for ITU-T, ANSI T1.102, Ethernet, SONET/SDH, Fibre Channel, USB 2.0, IEEE 1394b, Rapid I/O, OIF, CPRI, and Serial Video; (includes hardware clock recovery on DPO7254C/DPO7354C) Opt. PWR Power Measurement and Analysis Software Opt. SR-AERO Aerospace Serial Triggering and Analysis (MIL-STD-1553). Enables triggering on packet-level information on MIL-STD-1553 buses as well as analytical tools such as bus views, packet decoding, search tools, and packet decode tables with time stamp information Opt. SR-AUTO Automotive Serial Triggering and Analysis (CAN/LIN/FlexRay). Enables triggering on packet-level information on CAN, LIN, and FlexRay buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time stamp information Opt. SR-COMP Computer Serial Triggering and Analysis (RS-232/422/485/UART). Enables triggering on packet-level information on RS-232/422/485/UART buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time stamp information Opt. SR-DPHY MIPI(R) D-PHY Serial Analysis. Enables analysis of MIPI DSI-1 and CSI-2 buses with analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time stamp information Opt. SR-EMBD Embedded Serial Triggering and Analysis (I2C, SPI). Enables triggering on packet-level information on I2C and 2-wire and 3-wire SPI buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time stamp information Opt. SR-ENET Ethernet Serial Analysis (10BASE-T, 100BASE-TX). Enables analysis of Ethernet buses as well as analytical tools such as bus views, packet decoding, search tools, and packet decode tables with time stamp information Opt. SR-PCIE PCI Express Serial Analysis. Enables analysis of PCI Express buses with analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time stamp information (For models of bandwidth 1 GHz only) ( Due to large volumes of data, use of standard highcapacity hard drive rather than the smaller SSD is recommended.) Opt. SR-USB USB 2.0 Serial Triggering and Analysis (LS, FS, HS). Enables triggering on packet-level content for lowspeed and full-speed USB serial buses. Also enables analytical tools such as bus views, packet decoding, search tools, and packet decode tables with time stamp information for low-speed, full-speed, and highspeed USB serial buses. USB High Speed supported only on 1 GHz models Opt. SR-810B 8b/10b Serial Analysis. Enables analysis of 8b/10b buses with analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time stamp information Opt. ST1G 64-bit NRZ Serial Trigger and 8b/10b Serial Protocol Decode (includes Opt. SR-810B) (For models of bandwidth 2.5 GHz only) Opt. SVA AM/FM/PM Audio Signal Analysis (Requires Opt. SVE) Opt. SVE SignalVu(R) Essentials - Vector Signal Analysis Software Opt. SVM SignalVu(R) General Purpose Modulation Analysis (Requires Opt. SVE) Opt. SVO SignalVu(R) Flexible OFDM Analysis (Requires Opt. SVE) Opt. SVP SignalVu(R) Advanced Signal Analysis (including pulse measurements) (Requires Opt. SVE) Opt. SVT SignalVu(R) Frequency and Phase Settling Time Measurements (Requires Opt. SVE) Opt. USB USB 2.0 Compliance Test Software (Requires TDSUSBF (USB Test Fixture). 2 GHz bandwidth required for high-speed USB) DPO7000C Series Datasheet - DPO7000C Series TekExpress application framework options Bundle Options Option Description Opt. USBPWR Automated compliance test solution for USB power adapters Opt. VET Visual Trigger and Search Option Description TEKEXP TekExpress(R) Automation Framework Opt. D-PHYTX D-PHY Automated Solution (Requires Opt. DJA) (For models of bandwidth 2.5 GHz only) Opt. HEAC HEAC Automated Solution (Requires Opt. DJA, 2RL, MTM, ST1G) (For models of bandwidth 2.5 GHz only) These bundled items must be purchased at the same time as the instrument purchase. Option Description Opt. PS1 Power Solution Bundle: DPOPWR, P5205A, TCP0030A, TPA-BNC, 067-1686-xx (Deskew Fixture) Opt. PS2 Power Solution Bundle: DPOPWR, THDP0200, TCP0030A, 067-1686-xx (Deskew Fixture) Opt. PS3 Power Solution Bundle: DPOPWR, TMDP0200, TCP0020, 067-1686-xx (Deskew Fixture) Floating license options Floating licenses offer an alternative method to manage your Tektronix asset. Floating licenses allow license-key enabled options to be easily moved among all your MSO/ DPO5000, DPO7000, and DPO/DSA/MSO70000 Series of Tektronix oscilloscopes. Floating licenses are available for the following license-key enabled options. Check http://www.tek.com/products/oscilloscopes/floatinglicenses for additional information about floating license options. Option Description DPOFL-DDRA DDR Memory Bus Analysis (Requires Opt. DJA) (For models of bandwidth 1 GHz only) DPOFL-DJA Jitter and Eye Analysis Tools - Advanced (DPOJET) DPOFL-D-PHY MIPI(R) D-PHY Transmitter Debug, Characterization and Compliance Test Solution (Requires Opt. DJA) (For models of bandwidth 2.5 GHz only) DPOFL-ET3 Ethernet Compliance Testing (Requires TF-GBE-BTP or TF-GBE-ATP Ethernet Test Fixture) DPOFL-HSIC USB HSIC protocol decode and electrical validation (For models of bandwidth 2.5 GHz only.) DPOFL-LSA Low-speed Automotive Serial Analysis Bundle, includes CAN Trigger, CAN/LIN Decode and Analysis (includes TDSVNM) DPOFL-LT Waveform Limit Testing DPOFL-MOST Electrical Compliance and Debug Test Solution for MOST50 and MOST150 (Requires Opt. DJA) DPOFL-MTM Mask Testing for ITU-T, ANSI T1.102, Ethernet, SONET/SDH, Fibre Channel, USB 2.0, IEEE 1394b, Rapid I/O, OIF, CPRI, and Serial Video; (includes hardware clock recovery on DPO7254C/DPO7354C) DPOFL-PWR Power Measurement and Analysis DPOFL-SR-AERO Aerospace Serial Triggering and Analysis (MIL-STD-1553). Enables triggering on packet-level information on MILSTD-1553 buses as well as analytical tools such as digital views of the signal, bus views, and packet decoding DPOFL-SR-AUTO Automotive Serial Triggering and Analysis (CAN/LIN/FlexRay). Enables triggering on packet-level information on CAN, LIN, and FlexRay buses as well as analytical tools such as digital views of the signal, bus views, and packet decoding DPOFL-SR-COMP Computer Serial Triggering and Analysis (RS-232/422/485/UART). Enables triggering on packet-level information on RS-232/422/485/UART buses as well as analytical tools such as digital views of the signal, bus views, and packet decoding DPOFL-SR-DPHY MIPI(R) D-PHY Serial Analysis. Enables analysis of MIPI DSI-1 and CSI-2 buses with analytical tools such as digital views of the signal, bus views, and packet decoding DPOFL-SR-EMBD Embedded Serial Triggering and Analysis (I2C, SPI). Enables triggering on packet-level information on I2C and SPI buses as well as analytical tools such as digital views of the signal, bus views, and packet decoding DPOFL-SR-ENET Ethernet Serial Analysis (10BASE-T and 100BASE-TX) Ethernet Serial Analysis. Enables analysis of Ethernet buses with analytical tools such as digital views of the signal, bus views, and packet decoding DPOFL-SR-PCIE PCI Express Serial Analysis. Enables analysis of PCI Express buses with analytical tools such as digital views of the signal, bus views, and packet decoding (For models of bandwidth 1 GHz only) (Due to large volumes of data, use of standard high-capacity hard drive rather than the smaller SSD is recommended) www.tektronix.com 21 Datasheet Option Description DPOFL-SR-USB USB 2.0 Serial Triggering and Analysis (LS, FS, HS). Enables triggering on packet-level content for low-speed and full-speed USB serial buses. Also enables analytical tools such as digital views of the signal, bus views, and packet decoding for low-speed, fullspeed, and high-speed USB serial buses. USB High Speed supported only on 1 GHz models DPOFL-SR-810B 8b/10b Serial Analysis. Enables analysis of 8b/10b buses with analytical tools such as digital views of the signal, bus views, and packet decoding DPOFL- ST1G 64-bit NRZ Serial Trigger and 8b/10b Serial Protocol Decode (includes Opt. SR-810B) (For models of bandwidth 2.5 GHz only) DPOFL-SVA SignalVu(R) AM/FM/PM Audio Signal Analysis (Requires Opt. SVE) DPOFL-SVE SignalVu(R) Essentials - Vector Signal Analysis Software DPOFL-SVM SignalVu(R) General Purpose Modulation Analysis (Requires Opt. SVE) DPOFL-SVO SignalVu(R) Flexible OFDM Analysis (Requires Opt. SVE) DPOFL-SVP SignalVu(R) Advanced Signal Analysis (including pulse measurements) (Requires Opt. SVE) DPOFL-SVT SignalVu(R) Frequency and Phase Settling Time Measurements (Requires Opt. SVE) DPOFL-USB USB 2.0 Compliance Testing (Requires TDSUSBF USB Test Fixture) 2 GHz bandwidth required for high-speed USB. DPOFL-USBPWR Automated compliance test solution for USB power adapters DPOFL-VET Visual Trigger and Search Power plug options Opt. A0 North America power plug (115 V, 60 Hz) Opt. A1 Universal Euro power plug (220 V, 50 Hz) Opt. A2 United Kingdom power plug (240 V, 50 Hz) Opt. A3 Australia power plug (240 V, 50 Hz) Opt. A5 Switzerland power plug (220 V, 50 Hz) Opt. A6 Japan power plug (100 V, 110/120 V, 60 Hz) Opt. A10 China power plug (50 Hz) Opt. A11 India power plug (50 Hz) Opt. A12 Brazil power plug (60 Hz) Opt. A99 No power cord Language options Opt. L0 English manual Opt. L1 French manual Opt. L3 German manual Opt. L5 Japanese manual Opt. L7 Simplified Chinese manual Opt. L8 Traditional Chinese manual Opt. L9 Korean manual Opt. L10 Russian manual Opt. L99 No manual 22 www.tektronix.com DPO7000C Series Datasheet - DPO7000C Series Service options Opt. C3 Calibration Service 3 Years Opt. C5 Calibration Service 5 Years Opt. D1 Calibration Data Report Opt. D3 Calibration Data Report 3 Years (with Opt. C3) Opt. D5 Calibration Data Report 5 Years (with Opt. C5) Opt. G3 Complete Care 3 Years (includes loaner, scheduled calibration, and more) Opt. G5 Complete Care 5 Years (includes loaner, scheduled calibration, and more) Opt. R3 Repair Service 3 Years (including warranty) Opt. R5 Repair Service 5 Years (including warranty) Probes and accessories are not covered by the oscilloscope warranty and Service Offerings. Refer to the datasheet of each probe and accessory model for its unique warranty and calibration terms. Recommended accessories Probes Tektronix offers over 100 different probes to meet your application needs. For a comprehensive listing of available probes, please visit www.tektronix.com/probes. TAP3500 3.5 GHz TekVPI active single-ended probe TAP2500 2.5 GHz TekVPI active single-ended probe TAP1500 1.5 GHz TekVPI active single-ended probe TDP3500 3.5 GHz TekVPI differential voltage probe with 2 V differential input voltage TDP1500 1.5 GHz TekVPI differential voltage probe with 8.5 V differential input voltage TDP1000 1 GHz TekVPI differential voltage probe with 42 V differential input voltage TDP0500 500 MHz TekVPI differential voltage probe with 42 V differential input voltage TCP0150 20 MHz TekVPITM150 Ampere AC/DC current probe TCP0030A 120 MHz TekVPI 30 Ampere AC/DC current probe TCP0020 50 MHz TekVPI 20 Ampere AC/DC current probe TMDP0200 750 V, 200 MHz high-voltage differential probe THDP0200 1.5 kV, 200 MHz high-voltage differential probe THDP0100 6 kV, 100 MHz high-voltage differential probe P5100A 2.5 kV, 500 MHz, 100X high-voltage passive probe P6015A 20 kV, 75 MHz high-voltage passive probe P6158 3 GHz, 20X low-capacitance passive probe Accessories 077-0076-xx Service Manual, pdf on hard drive 016-1985-xx Rackmount Kit 065-0881-xx Removable HD Spare with rotational media 016-1979-xx Front HD option for Rackmount Kit 119-7083-xx Mini Keyboard (USB interface) 119-6297-xx Full-size keyboard with 4-port USB hub 016-1970-xx Transit Case K420 Oscilloscope Cart www.tektronix.com 23 Datasheet Cables 012-0991-xx GPIB Cable (1 m) 012-0991-xx GPIB Cable (2 m) Test fixtures 067-1686-xx Probe Calibration / Power Deskew Test Fixture TDSUSBF Test Fixture for use with Opt. USB TF-GBE-ATP 10/100/1000BASE-T Advanced Test Package (consists of test fixture PCB set, RJ45 interconnect cable, and 1000BASE-T jitter test channel cable) TF-GBE-BTP 10/100/1000BASE-T Basic Test Package (consists of test fixture PCB set and RJ45 interconnect cable) TF-GBE-EE Additional test fixture for Energy Efficient Ethernet measurements. Order through Crescent Heart Software (http://www.c-h-s.com) Adapters TPA-BNC TekVPI-to-TekProbe BNC Adapter P6701B Optical/Electrical Converter (Multi Mode). Requires TekVPI(R) to TekProbe BNC adapter (TPA-BNC). P6703B Optical/Electrical Converter (Single Mode). Requires TekVPI(R) to TekProbe BNC adapter (TPA-BNC). Software SIGEXPTE NI LabVIEW SignalExpress Tektronix Edition Software (Full Version) Upgrade options To upgrade your DPO7000C Series oscilloscope, order DPO-UP and option listed below. For example, DPO-UP DDRA. To upgrade record length: RL02 From Standard Configuration to Opt. 2RL Configuration RL05 From Standard Configuration to Opt. 5RL Configuration RL010 From Standard Configuration to Opt. 10RL Configuration RL25 From Opt. 2RL Configuration to Opt. 5RL Configuration RL210 From Opt. 2RL Configuration to Opt. 10RL Configuration RL510 From Opt. 5RL Configuration to Opt. 10RL Configuration To add a Solid State Hard Disk Drive: SSD Add an additional removable Solid State Drive (customer installable) To upgrade to a higher-capacity Hard Disk Drive: HDD7 Add an additional higher-capacity removable Hard Disk Drive (customer installable) To upgrade DPO7000C Series with: DDRA Add Option DDRA (Requires Opt. DJA) (For models of bandwidth 1 GHz only) DJAM Add Opt. DJA - Jitter and Eye Analysis Tools - Advanced (DPOJET) D-PHY Add Opt. D-PHY - MIPI(R) D-PHY Transmitter Debug, Characterization, and Compliance Test Solution (Requires Opt. DJA) (For models of bandwidth 2.5 GHz only) ET3 Add Opt. ET3 - Ethernet Compliance Testing (Requires TF-GBE-BTP or TF-GBE-ATP Ethernet Test Fixture) HSIC Add Opt. HSIC USB - HSIC protocol decode and electrical validation (For models of bandwidth 2.5 GHz only.) LSA Add Opt. LSA - CAN Trigger, CAN/LIN Decode and Analysis LT Add Opt. LT - Waveform Limit Testing MOST Add Opt. MOST - MOST Essentials - Electrical Compliance and Debug Test Solution for MOST50 and MOST150 (Requires Opt. DJA) MTM Add Opt. MTM - Mask Testing 24 www.tektronix.com DPO7000C Series Datasheet - DPO7000C Series PWR Add Opt. PWR - Power Measurement and Analysis SR-AERO Add Opt. SR-AERO - Aerospace Serial Triggering and Analysis (MIL-STD-1553). Enables triggering on packet-level information on MIL-STD-1553 buses as well as analytical tools such as digital views of the signal, bus views, and packet decoding SR-AUTO Add Opt. SR-AUTO - Automotive Serial Triggering and Analysis (CAN/LIN/FlexRay). Enables triggering on packet-level information on CAN, LIN, and FlexRay buses as well as analytical tools such as digital views of the signal, bus views, and packet decoding SR-COMP Add Opt. SR-COMP - Computer Serial Triggering and Analysis (RS-232/422/485/UART) SR-DPHY Add Opt. SR-DPHY - MIPI(R) D-PHY Serial Analysis (DSI-1 and CSI-2) SR-EMBD Add Opt. SR-EMBD - Embedded Serial Triggering and Analysis (I2C, SPI) SR-ENET Add Opt. SR-ENET - Ethernet Serial Analysis (10BASE-T, 100BASE-TX) SR-PCIE Add Opt. SR-PCIE - PCI Express Serial Analysis. Enables analysis of PCI Express buses with analytical tools such as digital views of the signal, bus views, and packet decoding (For models of bandwidth 1 GHz only) ( Due to large volumes of data, use of standard high-capacity hard drive rather than the smaller SSD is recommended.) SR-USB Add Opt. SR-USB - USB 2.0 Serial Triggering and Analysis (LS, FS, HS) SR-810B Add Opt. SR-810B - 8b/10b Serial Analysis. Enables analysis of 8b/10b buses with analytical tools such as digital views of the signal, bus views, and packet decoding SSD Add Opt. SSD - Solid State Hard Drive ST1G Add Opt. ST1G - 64-bit NRZ Serial Trigger and 8b/10b Serial Protocol Decode (includes Opt. SR-810B) (For models of bandwidth 2.5 GHz only) SVEM Add Opt. SVE - SignalVu Essentials Vector Signal Analysis SVA Add Opt. SVA - SignalVu AM/FM/Direct Audio Measurements (Requires Opt. SVE) SVM Add Opt. SVM - SignalVu General Purpose Modulation Analysis (Requires Opt. SVE) SVO Add Opt. SVO- SignalVu Flexible OFDM Analysis (Requires Opt. SVE) SVP Add Opt. SVP - SignalVu Pulse Advanced Signal Analysis (Requires Opt. SVE) SVT Add Opt. SVT - SignalVu Settling Time Measurements - Frequency and Phase (Requires Opt. SVE) USB Add Opt. USB - USB 2.0 Compliance Testing (Requires TDSUSBF (USB Test Fixture). 2 GHz bandwidth required for high-speed USB) USBPWR Add Opt. USBPWR - Automated compliance test solution for USB power adapters VETM Add Opt. VET - Visual Trigger and Search Tektronix is registered to ISO 9001 and ISO 14001 by SRI Quality System Registrar. www.tektronix.com 25 Datasheet ASEAN / Australasia (65) 6356 3900 Belgium 00800 2255 4835* Central East Europe and the Baltics +41 52 675 3777 Finland +41 52 675 3777 Hong Kong 400 820 5835 Japan 81 (3) 6714 3010 Middle East, Asia, and North Africa +41 52 675 3777 People's Republic of China 400 820 5835 Republic of Korea 001 800 8255 2835 Spain 00800 2255 4835* Taiwan 886 (2) 2722 9622 * European toll-free number. If not accessible, call: +41 52 675 3777 Austria 00800 2255 4835* Brazil +55 (11) 3759 7627 Central Europe & Greece +41 52 675 3777 France 00800 2255 4835* India 000 800 650 1835 Luxembourg +41 52 675 3777 The Netherlands 00800 2255 4835* Poland +41 52 675 3777 Russia & CIS +7 (495) 6647564 Sweden 00800 2255 4835* United Kingdom & Ireland 00800 2255 4835* Balkans, Israel, South Africa and other ISE Countries +41 52 675 3777 Canada 1 800 833 9200 Denmark +45 80 88 1401 Germany 00800 2255 4835* Italy 00800 2255 4835* Mexico, Central/South America & Caribbean 52 (55) 56 04 50 90 Norway 800 16098 Portugal 80 08 12370 South Africa +41 52 675 3777 Switzerland 00800 2255 4835* USA 1 800 833 9200 Updated 10 April 2013 For Further Information. Tektronix maintains a comprehensive, constantly expanding collection of application notes, technical briefs and other resources to help engineers working on the cutting edge of technology. Please visit www.tektronix.com. Copyright (c) Tektronix, Inc. All rights reserved. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specification and price change privileges reserved. TEKTRONIX and TEK are registered trademarks of Tektronix, Inc. All other trade names referenced are the service marks, trademarks, or registered trademarks of their respective companies. 19 Jun 2013 www.tektronix.com 48W-26543-11