REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update the boilerplate to current requirements as specified in MIL-PRF-38535. Editorial changes throughout. - jak 06-10-02 Thomas M. Hess REV SHEET REV A A A SHEET 15 16 17 REV STATUS REV A A A A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Thanh V. Nguyen STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY Thanh V. Nguyen APPROVED BY Monica L. Poelking DRAWING APPROVAL DATE 94-02-18 REVISION LEVEL AMSC N/A DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http://www.dscc.dla.mil A MICROCIRCUIT, DIGITAL, ADVANCED CMOS, OCTAL D-TYPE LATCH WITH THREE-STATE OUTPUTS, MONOLITHIC SILICON SIZE CAGE CODE A 67268 SHEET DSCC FORM 2233 APR 97 1 OF 5962-92180 17 5962-E474-06 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - Federal stock class designator \ 92180 RHA designator (see 1.2.1) 01 M R A Device type (see 1.2.2) Device class designator (see 1.2.3) Case outline (see 1.2.4) Lead finish (see 1.2.5) / \/ Drawing number 1.2.1 RHA designator. Device classes Q, and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type 01 Generic number 54ACQ573 Circuit function Octal D-type latch with three-state outputs 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class M Q, or V Device requirements documentation Vendor self-certification to the requirements for MIL-STD-883 compliant, nonJAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter R S 2 Descriptive designator GDIP1-T20 or CDIP2-T20 GDFP2-F20 or CDFP3-F20 CQCC1-N20 Terminals 20 20 20 Package style Dual-in-line Flat pack Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q, and V or MIL-PRF-38535, appendix A for device class M. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92180 A REVISION LEVEL A SHEET 2 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) ........................................................................... DC input voltage range (VIN) ......................................................................... DC output voltage range (VOUT) .................................................................... DC input clamp current (IIK): VIN = -0.5 V ................................................................................................. VIN = VCC + 0.5 V......................................................................................... DC output clamp current (IOK): VOUT = -0.5 V............................................................................................... VOUT = VCC + 0.5 V ...................................................................................... DC output current (IOUT) (per output pin) ....................................................... DC VCC or GND current (ICC, IGND) (per pin) .................................................. Storage temperature range (TSTG) ................................................................ Maximum power dissipation (PD) ................................................................. Lead temperature (soldering, 10 seconds).................................................... Thermal resistance, junction-to-case (JC) .................................................... Junction temperature (TJ) ............................................................................. -0.5 V dc to +7.0 V dc -0.5 V dc to VCC + 0.5 V dc -0.5 V dc to VCC + 0.5 V dc -20 mA +20 mA -20 mA +20 mA 50 mA 400 mA -65C to +150C 500 mW +300C See MIL-STD-1835 +175C 1.4 Recommended operating conditions. 2/ 3/ Supply voltage range (VCC) ........................................................................... Input voltage range (VIN) ............................................................................... Output voltage range (VOUT).......................................................................... Minimum high level input voltage (VIH): VCC = 3.0 V ................................................................................................. VCC = 4.5 V ................................................................................................. VCC = 5.5 V ................................................................................................. Maximum low level input voltage (VIL): VCC = 3.0 V ................................................................................................. VCC = 4.5 V ................................................................................................. VCC = 5.5 V ................................................................................................. Case operating temperature range (TC) ........................................................ Minimum input edge rate (V/t): (VIN from 0.3VCC to 0.7VCC or from 0.7VCC to 0.3VCC) ................................ Maximum high level output current (IOH): VCC = 3.0 V ................................................................................................. VCC = 4.5 V ................................................................................................. Maximum low level output current (IOL): VCC = 3.0 V ................................................................................................. VCC = 4.5 V ................................................................................................. +2.0 V dc to +6.0 V dc 0.0 V to VCC 0.0 V to VCC 2.1 V 3.15 V 3.85 V 0.9 V 1.35 V 1.65 V -55C to +125C 125 mV/ns -12 mA -24 mA +12 mA +24 mA 1/ Stresses above the absolute maximum rating may cause permanent damage to the device, Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the full specified VCC range and case temperature range of -55C to +125C. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92180 A REVISION LEVEL A SHEET 3 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 MIL-STD-1835 - Test Method Standard Microcircuits. Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 MIL-HDBK-780 - List of Standard Microcircuit Drawings. Standard Microcircuit Drawings. (Copies of these documents are available online at http://assist.daps.dla.mil/quicksearch/ or http://assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. ELECTRONIC INDUSTRIES ALLIANCE (EIA) JEDEC Standard No. 20 - Standard for Description of 54/74ACXXXX and 54/74ACTXXXX Advanced High-Speed CMOS Devices. (Copies of these documents are available online at http://www.eia.org or from the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834.) 2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Ground bounce waveforms and test circuit. The ground bounce waveforms and test circuit shall be as specified on figure 4. 3.2.6 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 5. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92180 A REVISION LEVEL A SHEET 4 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 38 (see MIL-PRF-38535, appendix A). STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92180 A REVISION LEVEL A SHEET 5 TABLE I. Electrical performance characteristics. Test and MIL-STD-883 test method 1/ High level output voltage 3006 Symbol VOH Test conditions 2/ -55C TC +125C +3.0 V VCC +5.5 V unless otherwise specified For all inputs affecting output under test, VIN = VIH or VIL For all other inputs, VIN = VCC or GND VCC Group A subgroups IOH = -50 A 3.0 V 1, 2, 3 Min 2.90 IOH = -12 mA 4.5 V 5.5 V 3.0 V 1, 2, 3 1, 2, 3 1 4.40 5.40 2.56 2, 3 2.40 5.5 V 1 2, 3 1 2, 3 1, 2, 3 3.86 3.70 4.86 4.70 3.85 3.0 V 1, 2, 3 0.10 4.5 V 5.5 V 3.0 V 1, 2, 3 1, 2, 3 1 0.10 0.10 0.36 2, 3 0.50 0.36 0.50 0.36 0.50 1.65 5.7 IOH = -24 mA 4.5 V 5.5 V Low level output voltage 3007 VOL For all inputs affecting output under test, VIN = VIH or VIL For all other inputs, VIN = VCC or GND IOH = -50 mA 4/ IOL = 50 A IOL = 12 mA IOL = 24 mA 4.5 V IOL = 50 mA 4/ 5.5 V 1 2, 3 1 2, 3 1, 2, 3 For input under test IIN = 18 mA For input under test IIN = -18 mA For input under test, VIN = 5.5 V For all other inputs, VIN = VCC or GND For input under test, VIN = 0.0 V For all other inputs, VIN = VCC or GND 4.5 V 1, 2, 3 5.5 V Positive input clamp voltage 3022 Negative input clamp voltage 3022 Input current high 3010 Input current low 3009 Three-state output leakage current, high 3021 VIC+ IOZH 5/ OE = VIH or GND For all other inputs, VIN = VCC or GND VOUT = 5.5 V 5.5 V Three-state output leakage current, low 3020 IOZL 5/ Quiescent supply current, output high 3005 Quiescent supply current, output low 3005 Quiescent supply current, output three-state 3005 ICCH OE = VIH or GND For all other inputs, VIN = VCC or GND VOUT = 0.0 V VICIIH IIL OE = GND For all other inputs, VIN = VCC or GND ICCL ICCZ 5/ 4.5 V Unit Max V V V -1.2 A 1 2, 3 1 2, 3 1 2, 3 0.1 1.0 -0.1 -1.0 0.5 10.0 5.5 V 1 2, 3 -0.5 -10.0 A 5.5 V 1 8.0 A 2, 3 160 1 8.0 2, 3 160 1 8.0 2, 3 160 5.5 V 5.5 V 5.5 V OE = VCC For all other inputs, VIN = VCC or GND Limits 3/ 5.5 V A A A A See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92180 A REVISION LEVEL A SHEET 6 TABLE I. Electrical performance characteristics - Continued. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +3.0 V VCC +5.5 V unless otherwise specified VCC Group A subgroups GND 4 Max 12 pF 5.5 V 4 15 pF 5.0 V 4 50 pF 5.0 V 4 1750 mV 5.0 V 4 -1200 mV 5.0 V 4 mV 5.0 V 4 3.0 V 4.5 V 5.5 V 3.0 V L L L 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.0 1.0 4.0 VOH +1000 VOH -1800 H H H 13.0 16.0 9.5 11.0 12.5 15.0 9.5 11.0 11.5 13.5 8.5 10.0 11.5 13.0 9.5 10.5 Limits 3/ Min Input capacitance 3012 Output capacitance 3012 Power dissipation capacitance Low level ground bounce noise High level VCC bounce noise Functional tests 3014 CIN COUT 5/ CPD 6/ VOLP 7/ VOLV 7/ VOHP 7/ VOHV 7/ 8/ TC = +25C See 4.4.1c VIH = VCC VIL = 0.0 V TA = +25C See 4.4.1d See figure 4 Propagation delay time, Dn to On 3003 tPLH1, tPHL1 9/ For all inputs, VIN = VIH or VIL Verify output VO See 4.4.1b CL = 50 pF minimum RL = 500 See figure 5 Propagation delay time, LE to On 3003 tPLH2, tPHL2 9/ CL = 50 pF minimum RL = 500 See figure 5 3.0 V Propagation delay time, output enable, OE to On 3003 tPZH, tPZL 9/ CL = 50 pF minimum RL = 500 See figure 5 3.0 V Propagation delay time, output disable, OE to On 3003 tPHZ, tPLZ 9/ CL = 50 pF minimum RL = 500 See figure 5 3.0 V Setup time, high or low, Dn to LE ts 10/ CL = 50 pF minimum RL = 500 See figure 5 3.0 V 7, 8 7, 8 7, 8 9 10, 11 9 10, 11 9 10, 11 9 10, 11 9 10, 11 9 10, 11 9 10, 11 9 10, 11 9, 10, 11 4.5 V 9, 10, 11 4.0 CL = 50 pF minimum RL = 500 See figure 5 3.0 V 9, 10, 11 2.0 4.5 V 9, 10, 11 2.0 CL = 50 pF minimum RL = 500 See figure 5 3.0 V 9, 10, 11 5.0 4.5 V 9, 10, 11 5.0 Hold time, high or low, Dn from LE LE pulse width, high th 10/ tw 10/ 4.5 V 4.5 V 4.5 V 4.5 V Unit mV ns ns ns ns ns ns ns ns ns ns ns See footnotes on next sheet. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92180 A REVISION LEVEL A SHEET 7 TABLE I. Electrical performance characteristics - Continued. 1/ For tests not listed in the referenced MIL-STD-883, utilize the general test procedure under the conditions listed herein. 2/ Each input/output, as applicable, shall be tested at the specified temperature for the specified limits to the tests in table I herein. Output terminals not designated shall be high level logic, low level logic, or open, except for all ICC tests, the output terminals shall be open. When performing the ICC tests, the current meter shall be placed in the circuit such that all current flows through the meter. The values to be used for VIH and VIL shall be the VIH minimum and VIL maximum values listed in section 1.4 herein. 3/ For negative and positive voltage and current values, the sign designates the potential difference in reference to GND and the direction of current flow, respectively; and the absolute value of the magnitude, not the sign, is relative to the minimum and maximum limits, as applicable, listed herein. All devices shall meet or exceed the limits specified in table I, as applicable, at 3.0 V VCC 3.6 V and 4.5 V 5.5 V. 4/ Transmission driving tests are performed at VCC = 5.5 V dc with a 2 ms duration maximum. This test may be performed using VIN = VCC or GND. When VIN = VCC or GND is used, the test is guaranteed for VIN = 3.85 V or 1.65 V. 5/ Three-state output conditions are required. 6/ Power dissipation capacitance (CPD) determines the power consumption, PD = (CPD + CL) (VCC x VCC)f + (ICC x VCC), and the current consumption, IS = (CPD + CL)VCCf + ICC. For both PD and IS, f is the frequency of the input signal, and CL is the external output load capacitance. 7/ This test is for qualification only. Ground and VCC bounce tests are performed on a non-switching (quiescent) output and are used to measure the magnitude of induced noise caused by other simultaneously switching outputs. The test is performed on a low noise bench test fixture. For the device under test, all outputs shall be loaded with 500 of load resistance and a minimum of 50 pF of load capacitance (see figure 4). Only chip capacitors and resistors shall be used. The output load components shall be located as close as possible to the device outputs. It is suggested that, whenever possible, this distance be kept to less than 0.25 inches. Decoupling capacitors shall be placed in parallel from VCC to ground. The device manufacturer shall determine the values of these decoupling capacitors. The low and high level ground and VCC bounce noise is measured at the quiet output using a 1 GHz minimum bandwidth oscilloscope with a 50 input impedance. The device inputs shall be conditioned such that all outputs are at a high nominal VOH level. The device inputs shall then be conditioned such that they switch simultaneously and the output under test remains at VOH as all other outputs possible are switched from VOH to VOL. VOHV and VOHP are then measured from the nominal VOH level to the largest negative and positive peaks, respectively (see figure 4). This is then repeated with the same outputs not under test switching from VOL to VOH. The device inputs shall be conditioned such that all outputs are at a low nominal VOL level. The device inputs shall then be conditioned such that they switch simultaneously and the output under test remains at VOL as all other outputs possible are switched from VOL to VOH. VOLP and VOLV are then measured from the nominal VOL level to the largest positive and negative peaks, respectively (see figure 4). This is then repeated with the same outputs not under test switching from VOH to VOL. 8/ Tests shall be performed in sequence, attributes data only. Functional tests shall include the truth table and other logic patterns used for fault detection. The test vectors used to verify the truth table shall, at a minimum, test all functions of each input and output. All possible input to output logic patterns per function shall be guaranteed, if not tested, to the truth table in figure 2 herein. For output measurements, L < 0.3VCC and H 0.7VCC. 9/ AC limits at VCC = 5.5 V are equal to the limits at VCC = 4.5 V and guaranteed by testing at VCC = 4.5 V. AC limits at VCC = 3.6 V are equal to the limits at VCC = 3.0 V and guaranteed by testing at VCC = 3.0 V. Minimum propagation delay time limits for VCC = 5.5 V and VCC = 3.6 V shall be guaranteed to be no more than 0.5 ns less than those specified at VCC = 4.5 V and VCC = 3.0 V, respecftively, in table I herein. For propagation delay tests, all paths must be tested. 10/ This parameter shall be guaranteed, if not tested, to the limits in table I, herein. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92180 A REVISION LEVEL A SHEET 8 Device type 01 Case outlines R, S, and 2 Terminal number Terminal symbol 1 OE 2 D0 3 D1 4 D2 5 D3 6 D4 7 D5 8 D6 9 D7 10 GND 11 LE 12 O7 13 O6 14 O5 15 O4 16 O3 17 O2 18 O1 19 O0 20 VCC Terminal description Terminal symbol Description Dn (n = 0 to 7) Data inputs On (n = 0 to 7) Outputs (noninverting) LE Latch input input (active high) Output enable control input OE (active low) FIGURE 1. Terminal connections. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92180 A REVISION LEVEL A SHEET 9 Inputs OE H L L L L L LE X H H L Device type 01 Internal Dn X L H l h X On X H L H L O0 Outputs On Z L H L H O0 L = Low voltage level H = High voltage level X = Irrelevant = High-to-low transition l = Low voltage level meeting the setup and hold times in table I relative to the transition of LE h = High voltage level meeting the setup and hold times in table I relative to the transition of LE Z = High impedance O0 = Previous O0 before high-to-low transition of latch enable FIGURE 2. Truth table. FIGURE 3. Logic diagram. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92180 A REVISION LEVEL A SHEET 10 NOTES: 1. CL includes a 47 pF chip capacitor (-0 percent, +20 percent) and at least 3 pF of equivalent capacitance from the test jig and probe. 2. RL = 450 1 percent, chip resistor in series with a 50 termination. For monitored outputs, the 50 termination shall be the 50 characteristic impedance of the coaxial connector to the oscilloscope. 3. Input signal to the device under test: a. VIN = 0.0 V to VCC; duty cycle = 50 percent; fIN 1 MHz. b. tr, tf = 3.0 ns 1.0 ns. For input signal generators incapable of maintaining these values of tr and tf, the 3.0 ns limit may be increased up to 10 ns, as needed, maintaining the 1.0 ns tolerance and guaranteeing the results at 3.0 ns 1.0 ns; skew between any two switching input signals (tsk): 250 ps. FIGURE 4. Ground bounce waveforms and test circuit. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92180 A REVISION LEVEL A SHEET 11 FIGURE 5. Switching waveforms and test circuit. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92180 A REVISION LEVEL A SHEET 12 NOTES: 1. When measuring tPLZ and tPZL: VTEST = 2 x VCC. 2. When measuring tPHZ, tPZH, tPLH, and tPHL: VTEST = Open. 3. The tPZL and tPLZ reference waveform is for the output under test with internal conditions such that the output is at VOL except when disabled by the output enable control. The tPZH and tPHZ reference waveform is for the output under test with internal conditions such that the output is at VOH except when disabled by the output enable control. 4. CL = 50 pF minimum or equivalent (includes test jig and probe capacitance). 5. RT = 50 or equivalent. RL = 500 or equivalent. 6. Input signal from pulse generator: VIN = 0.0 V to VCC; PRR 10 MHz; tr 3.0 ns; tf 3.0 ns; tr and tf shall be measured from 0.3VCC to 0.7VCC and from 0.7VCC to 0.3VCC, respectively; duty cycle = 50 percent. 7. Timing parameters shall be tested at a minimum input frequency of 1 MHz. 8. The outputs are measured one at a time with one transition per measurement. FIGURE 5. Switching waveforms and test circuit.- Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92180 A REVISION LEVEL A SHEET 13 4. VERIFICATION 4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with MIL-PRF-38535 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. For device class M, sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and shall be conducted on all devices prior to qualification and technology conformance inspection. For device class M, screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. 4.2.1 Additional criteria for device class M. a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA = +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein. 4.2.2 Additional criteria for device classes Q and V. a. The burn-in test duration, test condition and test temperature, or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The burn-in test circuit shall be maintained under document revision level control of the device manufacturer's Technology Review Board (TRB) in accordance with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein. c. Additional screening for device class V beyond the requirements of device class Q shall be as specified in MIL-PRF-38535, appendix B. 4.3 Qualification inspection for device classes Q and V. Qualification inspection for device classes Q and V shall be in accordance with MIL-PRF-38535. Inspections to be performed shall be those specified in MIL-PRF-38535 and herein for groups A, B, C, D, and E inspections (see 4.4.1 through 4.4.4). 4.4 Conformance inspection. Technology conformance inspection for classes Q and V shall be in accordance with MIL-PRF-38535 including groups A, B, C, D, and E inspections and as specified herein. Quality conformance inspection for device class M shall be in accordance with MIL-PRF-38535, appendix A and as specified herein. Inspections to be performed for device class M shall be those specified in method 5005 of MIL-STD-883 and herein for groups A, B, C, D, and E inspections (see 4.4.1 through 4.4.4). 4.4.1 Group A inspection. a. Tests shall be as specified in table II herein. b. For device class M, subgroups 7 and 8 tests shall be sufficient to verify the truth table in figure 2 herein. The test vectors used to verify the truth table shall, at a minimum, test all functions of each input and output. All possible input to output logic patterns per function shall be guaranteed, if not tested, to the truth table in figure 2, herein. For device classes Q and V, subgroups 7 and 8 shall include verifying the functionality of the device. c. CIN, COUT, and CPD shall be measured only for initial qualification and after process or design changes which may affect capacitance. CIN and COUT shall be measured between the designated terminal and GND at a frequency of 1 MHz. CPD shall be tested in accordance with the latest revision of JEDEC Standard No. 20 and table I herein. For CIN, COUT, and CPD, test all applicable pins on five devices with zero failures. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92180 A REVISION LEVEL A SHEET 14 For CIN and COUT, a device manufacturer may qualify devices by functional groups. A specific functional group shall be composed of function types, that by design, will yield the same capacitance values when tested in accordance with table I, herein. The device manufacturer shall set a function group limit for the CIN and COUT tests. The device manufacturer may then test one device function from a functional group to the limits and conditions specified herein. All other device functions in that particular functional group shall be guaranteed, if not tested, to the limits and conditions specified in table I, herein. The device manufacturer shall submit to DSCC-VA the device functions listed in each functional group and the test results for each device tested. d. Ground and VCC bounce tests are required for all device classes. These tests shall be performed only for initial qualification, after process or design changes which may affect the performance of the device, and any changes to the test fixture. VOLP, VOLV, VOHP, and VOHV shall be measured for the worst case outputs of the device. All other outputs shall be guaranteed, if not tested, to the limits established for the worst case outputs. The worst case outputs tested are to be determined by the manufacturer. Test 5 devices assembled in the worst case package type supplied to this document. All other package types shall be guaranteed, if not tested, to the limits established for the worst case package. The package type to be tested shall be determined by the manufacturer. The device manufacturer will submit to DSCC-VA data that shall include all measured peak values for each device tested and detailed oscilloscope plots for each VOLP, VOLV, VOHP, and VOHV from one sample part per function. The plot shall contain the waveforms of both a switching output and the output under test. Each device manufacturer shall test product on the fixtures they currently use. When a new fixture is used, the device manufacturer shall inform DSCC-VA of this change and test the 5 devices on both the new and old test fixtures. The device manufacturer shall then submit to DSCC-VA data from testing on both fixtures that shall include all measured peak values for each device tested and detailed oscilloscope plots for each VOLP, VOLV, VOHP, and VOHV from one sample part per function. The plot shall contain the waveforms of both a switching output and the output under test. For VOHP, VOHV, VOLP, and VOLV, a device manufacturer may qualify devices by functional groups. A specific functional group shall be composed of function types, that by design, will yield the same test values when tested in accordance with table I, herein. The device manufacturer shall set a functional group limit for the VOHP, VOHV, VOLP, and VOLV tests. The device manufacturer may then test one device function from a functional group to the limits and conditions specified herein. All other device functions in that particular functional group shall be guaranteed, if not tested, to the limits and conditions specified in table I, herein. The device manufacturer shall submit to DSCC-VA the device functions listed in each functional group and the test results, along with the oscilloscope plots, for each device tested. 4.4.2 Group C inspection. The group C inspection end-point electrical parameters shall be as specified in table II herein. 4.4.2.1 Additional criteria for device class M. Steady-state life test conditions, method 1005 of MIL-STD-883: a. Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. b. TA = +125C, minimum. c. Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 4.4.2.2 Additional criteria for device classes Q and V. The steady-state life test duration, test condition and test temperature, or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The test circuit shall be maintained under document revision level control by the device manufacturer's TRB in accordance with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. 4.4.3 Group D inspection. The group D inspection end-point electrical parameters shall be as specified in table II herein. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92180 A REVISION LEVEL A SHEET 15 4.4.4 Group E inspection. Group E inspection is required only for parts intended to be marked as radiation hardness assured (see 3.5 herein). a. End-point electrical parameters shall be as specified in table II herein. b. For device classes Q and V, the devices or test vehicle shall be subjected to radiation hardness assured tests as specified in MIL-PRF-38535 for the RHA level being tested. For device class M, the devices shall be subjected to radiation hardness assured tests as specified in MIL-PRF-38535, appendix A for the RHA level being tested. All device classes must meet the postirradiation end-point electrical parameter limits as defined in table I at TA = +25C 5C, after exposure, to the subgroups specified in table II herein. TABLE II. Electrical test requirements. Test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Subgroups (in accordance with MIL-PRF-38535, table III) Device class M Device class Q Device class V Interim electrical parameters (see 4.2) --- 1 1 Final electrical parameters (see 4.2) 1/ 1, 2, 3, 7, 8, 9 1/ 1, 2, 3, 7, 8, 9, 10, 11 2/ 1, 2, 3, 7, 8, 9, 10, 11 Group A test requirements (see 4.4) 1, 2, 3, 4, 7, 8, 9, 10, 11 1, 2, 3, 4, 7, 8, 9, 10, 11 1, 2, 3, 4, 7, 8, 9, 10, 11 Group C end-point electrical parameters (see 4.4) 1, 2, 3 1, 2, 3, 7, 8 1, 2, 3, 7,8 Group D end-point electrical parameters (see 4.4) 1, 2, 3 1, 2, 3, 7, 8 1, 2, 3, 7, 8 Group E end-point electrical parameters (see 4.4) 1, 7, 9 1, 7, 9 1, 7, 9 1/ PDA applies to subgroup 1. 2/ PDA applies to subgroups 1 and 7. 4.5 Methods of inspection. Methods of inspection shall be specified as follows: 4.5.1 Voltage and current. Unless otherwise specified, all voltages given are referenced to the microcircuit GND terminal. Currents given are conventional current and positive when flowing into the referenced terminal. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92180 A REVISION LEVEL A SHEET 16 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.1.1 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing. 6.1.2 Substitutability. Device class Q devices will replace device class M devices. 6.2 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.3 Record of users. Military and industrial users should inform Defense Supply Center Columbus (DSCC) when a system application requires configuration control and which SMD's are applicable to that system. DSCC will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544. 6.4 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43218-3990, or telephone (614) 692-0547. 6.5 Abbreviations, symbols, and definitions. The abbreviations, symbols, and definitions used herein are defined in MIL-PRF-38535 and MIL-HDBK-1331. 6.6 Sources of supply. 6.6.1 Sources of supply for device classes Q and V. Sources of supply for device classes Q and V are listed in QML-38535. The vendors listed in QML-38535 have submitted a certificate of compliance (see 3.6 herein) to DSCC-VA and have agreed to this drawing. 6.6.2 Approved sources of supply for device class M. Approved sources of supply for class M are listed in MIL-HDBK-103. The vendors listed in MIL-HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DSCC-VA. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-92180 A REVISION LEVEL A SHEET 17 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 06-10-02 Approved sources of supply for SMD 5962-92180 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DSCC-VA. This information bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. DSCC maintains an online database of all current sources of supply at http://www.dscc.dla.mil/Programs/Smcr/. Standard microcircuit drawing PIN 1/ 5962-9218001MRA 5962-9218001MSA 5962-9218001M2A Vendor CAGE number 20714 0C7V7 20714 0C7V7 20714 0C7V7 Vendor similar PIN 2/ 54ACQ573DMQB 54ACQ573FMQB 54ACQ573LMQB 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed, contact the vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. Vendor CAGE number Vendor name and address 27014 National Semiconductor 2900 Semiconductor Drive P.O. Box 58090 Santa Clara, CA 95052-8090 0C7V7 QP Semiconductor 2945 Oakmead Village Court Santa Clara, CA 95051 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin.