Description
These high gain series couplers use a Light Emitting Di-
ode and an integrated high gain photodetector to pro-
vide extremely high current transfer ratio between input
and output. Separate pins for the photodiode and out-
put stage result in LVTTL compatible saturation voltages
and high speed operation. Where desired, the VCC and VO
terminals may be tied together to achieve conventional
photo-darlington operation. A base access terminal al-
lows a gain bandwidth adjustment to be made.
These optocouplers are for use in LVTTL/LVCMOS or
other low power applications. A 400% minimum current
transfer ratio is guaranteed over 0 to +70˚C operating
range for only 0.5 mA of LED current.
The HCPL-070L and HCPL-073L are surface mount de-
vices packaged in an industry standard SOIC-8 footprint.
The SOIC-8 does not require "through holes" in a PCB.
This package occupies approximately one-third the foot-
print area of the standard dual-in-line package. The lead
prole is designed to be compatible with standard sur-
face mount processes.
Functional Diagram
Features
3.3V/5V Dual Supply Voltages
Low power consumption
High current transfer ratio
Low input current requirements – 0.5 mA
LVTTL/LVCMOS compatible output
Performance guaranteed over temperature 0°C to +70°C
Base access allows gain bandwidth adjustment
High output current – 60 mA
Safety approval, UL, IEC/EN/DIN EN 60747-5-2, CSA
Applications
Ground isolate most logic families – LVTTL/LVCMOS
Low input current line receiver
High voltage insulation
EIA RS-232C line receiver
Telephone ring detector
V AC line voltage status indicator – low input power
dissipation
Low power systems – ground isolation
A 0.1 µF bypass capacitor connected between pins 8 and 5 is recommended.
CAUTION: It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation which may be induced by ESD.
HCPL-270L/070L/273L/073L
Low Input Current, High Gain, LVTTL/LVCMOS Compatible Optocouplers
Data Sheet
7
1
2
3
45
6
8
NC
ANODE
CATHODE
NC
VCC
VO
GND
TRUTH TABLE
HCPL-270L/070L HCPL-273L/073L
LED
ON
OFF
VO
LOW
HIGH
VB
VO2
VO1
VCC
GND
ANODE 1
CATHODE 1
CATHODE 2
ANODE 2
7
5
6
8
2
3
4
1
SHIELD
2
Ordering Information
HCPL-270L, HCPL-273L, HCPL-070L and HCPL-073L are UL Recognized with 3750 Vrms for 1 minute per UL1577 and
are approved under CSA Component Acceptance Notice #5, File CA 88324.
Option
Part RoHS non RoHS Surface Gull Tape UL 5000 Vrms/ IEC/EN/DIN
Number Compliant Compliant Package Mount Wing & Reel 1 Minute rating EN 60747-5-2 Quantity
-000E no option 300 mil DIP-8 50 per tube
HCPL-270L
-300E -300 X X 50 per tube
HCPL-273L
-500E -500 X X X 1000 per reel
-060E -060 X 100 per tube
-560E -560 X X X X 1500 per reel
-000E no option SO-8 X 100 per tube
HCPL-070L
-500E -500 X X 1500 per reel
HCPL-073L
-060E -060 X X 100 per tube
-560E -560 X X X 1500 per reel
To order, choose a part number from the part number column and combine with the desired option from the option
column to form an order entry.
Example 1:
HCPL-273L-500E to order product of 300 mil DIP Gull Wing Surface Mount package in Tape and Reel packaging with
IEC/EN/DIN EN 60747-5-2 Safety Approval and RoHS compliant.
Example 2:
HCPL-273L to order product of 300 mil DIP package in Tube packaging and non RoHS compliant.
Option datasheets are available. Contact your Avago sales representative or authorized distributor for information.
Remarks: The notation ‘#XXX’ is used for existing products, while (new) products launched since July 15, 2001 and
RoHS compliant will use ‘–XXXE.
3
Schematic
HCPL-270L/HCPL-070L HCPL-273L/HCPL-073L
Selection Guide
8-Pin DIP (300 Mil) Small Outline SO-8
Single Channel Dual Channel Single Channel Dual Channel Minimum Input
Package HCPL- Package HCPL- Package HCPL- Package HCPL- ON Current (IF) Minimum CTR
270L 273L 070L 073L 0.5 mA 400%
IF
8
VCC
2
3
ICC
VF
ANODE
CATHODE
+
-
VB
IB
6
5GND
VO
IO
7
SHIELD
IF2
6
5
GND
3
4
VO2
VF2
IO2
+
-
IF1
8
7
V
CC
1
2
V
O1
ICC
VF1
IO1
-
+
SHIELD
USE OF A 0.1 µF BYPASS CAPACITOR CONNECTED
BETWEEN PINS 5 AND 8 IS RECOMMENDED
4
Package Outline Drawings
8-Pin DIP Package
Small Outline SO-8 Package
XXXV
YWW
8 7 6 5
4321
5.994 ± 0.203
(0.236 ± 0.008)
3.937 ± 0.127
(0.155 ± 0.005)
0.406 ± 0.076
(0.016 ± 0.003) 1.270
(0.050) BSC
5.080 ± 0.127
(0.200 ± 0.005)
3.175 ± 0.127
(0.125 ± 0.005) 1.524
(0.060)
45¡ X 0.432
(0.017)
0.228 ± 0.025
(0.009 ± 0.001)
TYPE NUMBER
(LAST 3 DIGITS)
DATE CODE
0.305
(0.012) MIN.
TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH)
5.207 ± 0.254 (0.205 ± 0.010)
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX.
OPTION NUMBER 500 NOT MARKED.
NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX.
0.203 ± 0.102
(0.008 ± 0.004)
7°
PIN ONE
0 ~ 7°
*
*
OPTION 060 CODE
1.080 ± 0.320
(0.043 ± 0.013) 2.54 ± 0.25
(0.100 ± 0.010)
0.51 (0.020) MIN.
0.65 (0.025) MAX.
4.70 (0.185) MAX.
2.92 (0.115) MIN.
5° TYP. 0.254 + 0.076
- 0.051
(0.010 + 0.003)
- 0.002)
7.62 ± 0.25
(0.300 ± 0.010)
6.35 ± 0.25
(0.250 ± 0.010)
9.65 ± 0.25
(0.380 ± 0.010)
1.78 (0.070) MAX.
1.19 (0.047) MAX.
A XXXXZ
YYWW
DATE CODE
DIMENSIONS IN MILLIMETERS AND (INCHES).
5678
4321
OPTION CODE*
UL
RECOGNITION
UR
TYPE NUMBER
* MARKING CODE LETTER FOR OPTION NUMBERS
"L" = OPTION 020
"V" = OPTION 060
OPTION NUMBERS 300 AND 500 NOT MARKED.
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
3.56 ± 0.13
(0.140 ± 0.005)
7.49 (0.295)
1.9 (0.075)
0.64 (0.025)
LAND PATTERN RECOMMENDATION
5
Solder Reow Temperature Prole
Recommended Pb-Free IR Prole
Note: Non-halide ux should be used.
Note: Non-halide ux should be used.
Regulatory Information
The devices contained in this data sheet have been approved by the following organizations:
UL Approval under UL 1577, Component Recognition Program, File E55361.
CSA Approval under CSA Component Acceptance Notice #5, File CA 88324.
IEC/EN/DIN EN 60747-5-2
Approved under
IEC 60747-5-2:1997 + A1:2002
EN 60747-5-2:2001 + A1:2002
DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01 (Option 060 only)
217 °C
RAMP-DOWN
6°C/SEC.MAX.
RAMP-UP
3°C/SEC.MAX.
150 - 200°C
260 +0/-5°C
t25°C toPEAK
60to150SEC.
20-40SEC.
TIMEWITHIN5°CofACTUAL
PEAKTEMPERATURE
tp
ts
PREHEAT
60to180SEC.
tL
TL
Tsmax
Tsmin
25
Tp
TIME
TEMPERATURE
NOTES:
THE TIME FROM 25 °C to PEAK TEMPERATURE = 8 MINUTES MAX.
Tsmax = 200 °C, Tsmin = 150 °C
0
TIME (SECONDS)
TEMPERATURE (°C)
200
100
50 150100 200 250
300
0
30
SEC.
50 SEC.
30
SEC.
160°C
140°C
150°C
PEAK
TEMP.
245°C
PEAK
TEMP.
240°C
PEAK
TEMP.
230°C
SOLDERING
TIME
200°C
PREHEATING TIME
150°C, 90 + 30 SEC.
2.5°C ± 0.5°C/SEC.
3°C + 1°C/-0.5°C
TIGHT
TYPICAL
LOOSE
ROOM
TEMPERATURE
PREHEATING RATE 3°C + 1°C/-0.5°C/SEC.
REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC.
6
Insulation and Safety Related Specications
8-Pin DIP
(300 Mil) SO-8
Parameter Symbol Value Value Units Conditions
Minimum External Air L (101) 7.1 4.9 mm Measured from input terminals to output
Gap (External Clearance) terminals, shortest distance through air.
Minimum External Tracking L (102) 7.4 4.8 mm Measured from input terminals to output
(External Creepage) terminals, shortest distance path along body.
Minimum Internal Plastic 0.08 0.08 mm Through insulation distance, conductor to
Gap (Internal Clearance) conductor, usually the direct distance
between the photoemitter and photodetector
inside the optocoupler cavity.
Tracking Resistance CTI 200 200 Volts DIN IEC 112/VDE 0303 Part 1.
(Comparative Tracking
Index)
Isolation Group IIIa IIIa Material Group (DIN VDE 0110, 1/89, Table 1).
IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics
8-pin DIP
Description Symbol (300 mil) SO-8 Units
Installation classication per DIN VDE 0110/1.89, Table 1
for rated mains voltage ≤ 150 V rms I-IV
for rated mains voltage ≤ 300 V rms I-IV I-III
for rated mains voltage ≤ 600 V rms I-III I-II
Climatic Classication 55/100/21 55/100/21
Pollution Degree (DIN VDE 0110/1.89) 2 2
Maximum Working Insulation Voltage VIORM 630 566 Vpeak
Input to Output Test Voltage, Method b*
VPR = 1.875 x VIORM, 100% Production Test with tP = 1 sec, VPR 1181 1063 Vpeak
Partial Discharge < 5 pC
Input to Output Test Voltage, Method a*
VPR = 1.5 x VIORM, Type and Sample Test, VPR 945 849 Vpeak
tP = 60 sec, Partial Discharge < 5 pC
Highest Allowable Overvoltage* VIOTM 6000 4000 Vpeak
(Transient Overvoltage, tini = 10 sec)
Safety Limiting Values
(Maximum values allowed in the event of a failure,
also see Figure 11, Thermal Derating curve.)
Case Temperature TS 175 150 ˚C
Current (Input Current IF, PS = 0) IS,INPUT 400 150 mA
Output Power PS,OUTPUT 600 600 mW
Insulation Resistance at TS, VIO = 500 V RS ≥ 109 ≥ 109
*Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section, IEC/EN/DIN EN 60747-5-2, for a detailed description.
Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application.
7
Absolute Maximum Ratings (No Derating Required up to +85˚C)
Parameter Symbol Min. Max. Units
Storage Temperature TS –55 125 ˚C
Operating Temperature TA –40 85 ˚C
Average Forward Input Current IF(AVG) 20 mA
Peak Forward Input Current IF(PEAK) 40 mA
(50% Duty Cycle, 1 ms Pulse Width)
Peak Transient Input Current IF(TRAN) 1.0 A
(< 1 µs Pulse Width, 300 pps)
Reverse Input Voltage VR 5 V
Input Power Dissipation PI 35 mW
Output Current (Pin 6) IO 60 mA
Emitter Base Reverse Voltage (Pin 5-7) VEB 0.5 V
Supply Voltage and Output Voltage VCC –0.5 7 V
Output Power Dissipation PO 100 mW
Total Power Dissipation PT 135 mW
Lead Solder Temperature 260˚C for 10 sec., 1.6 mm below seating plane.
(for Through Hole Devices)
Reow Temperature Prole See Package Outline Drawings section.
(for SOIC-8 and Option #300)
Recommended Operating Conditions
Parameter Symbol Min. Max. Units
Power Supply Voltage VCC 2.7 7.0 V
Forward Input Current (ON) IF(ON) 0.5 12.0 mA
Forward Input Voltage (OFF) VF(OFF) 0 0.8 V
Operating Temperature TA 0 70 ˚C
8
Electrical Specications
0˚C ≤ TA ≤ +70˚C, 2.7 V ≤ VCC ≤ 3.3 V, 0.5 mA ≤ IF(ON) ≤ 12 mA, 0 V ≤ VF(OFF) ≤ 0.8 V, unless otherwise specied.
All typicals at TA = 25˚C. (See Note 8.)
Device
Parameter Sym. HCPL- Min. Typ.* Max. Units Test Conditions Fig. Note
Current Transfer CTR 400 1300 5000 % IF = 0.5 mA VCC = 3.3 V 1, 2 2
Ratio VO = 0.4 V
Logic Low VOL 0.05 0.3 V IF = 1.6 mA, VCC = 3.3 V
Output Voltage IO = 8 mA
0.05 0.4 V IF = 5.0 mA,
IO = 15 mA
Logic High IOH 5 25 µA VO = VCC = 3.3 V IF = 0 mA 2
Output Current
Logic Low ICCL 270L/070L 0.4 1.3 mA VCC = 3.3 V IF1 = IF2 = 1.6 mA
Supply Current 273L/073L 0.8 2.7 mA VO1 = VO2 = Open
Logic High ICCH 270L/070L 0.002 1 µA VCC = 3.3 V IF1 = IF2 = 0 mA
Supply Current 273L/073L 0.002 2 µA VO1 = VO2 = Open
Input Forward VF 1.5 1.7 V TA = 25˚C IF = 1.6 mA 3, 4
Voltage
Input Reverse BVR 5.0 V IR = 10 µA, 2
Breakdown Voltage TA = 25˚C
Temperature Coecient ∆VF/ -1.8 mV/°C IF = 1.6 mA
of Forward Voltage ∆TA
Input Capacitance CIN 60 pF f = 1 MHz, VF = 0 2
*All typical values at TA = 25˚C and VCC = 3.3 V, unless otherwise noted.
Electrical Specications
0°C ≤ TA ≤ 70°C, 4.5 V ≤ VCC ≤ 7 V, 0.5 mA ≤ IF(ON) ≤ 12 mA, 0 V ≤ VF(OFF) ≤ 0.8 V, unless otherwise specied.
All Typicals at TA = 25°C. (See note 8.)
Parameter Sym. Device Min. Typ.* Max. Units Test Conditions Fig. Note
Current Transfer Ratio CTR 300 1600 2600 % IF = 1.6 mA, VCC = 4.5V, VO = 0.5V 2, 3 2
Logic Low Output Voltage VOL 0.1 0.4 V IF = 1.6 mA, IO = 4.8 mA, VCC = 4.5V 1
Logic High Output Current IOH 0.1 250 μA VO = VCC = 7 V, IF = 0 mA 2
Logic Low ICCL 0.9 3 mA VCC = 7 V, IF1 = IF2 = 1.6 mA 5
Supply Current V01 = V02 = Open
Logic High ICCH 0.004 20 μA VCC = 7 V, IF1 = IF2 = 0 mA, 5
Supply Current V01 = V02 = Open
Input Forward Voltage VF 1.4 1.7 V TA = 25°C 4
1.75 V IF = 1.6 mA
Input Reverse BVR 5 V IR = 10 μA, TA = 25°C 2
Breakdown Voltage
Temperature Coecient ∆VF/ -1.8 mV/°C IF = 1.6 mA
of Forward Voltage ∆TA
Input Capacitance CIN 60 pF f = 1 MHz, VF = 0 2
*All typical values at TA = 25°C and VCC = 5 V, unless otherwise noted.
9
Switching Specications (AC)
Over Recommended Operating Conditions (TA = 0˚C to +70˚C), VCC = 3.3 V, unless otherwise specied. (See Note 8.)
Parameter Sym. Min. Typ.* Max. Units Test Conditions Fig. Note
Propagation Delay tPHL 30 µs IF = 0.5 mA, Rl = 4.7 kΩ 5 2
Time to Logic Low
at Output
Propagation Delay tPLH 90 µs IF = 0.5 mA, RL = 4.7 kΩ 5 2
Time to Logic High
at Output
Common Mode |CMH| 1000 10000 V/µs IF = 0 mA, TA = 25˚C, 6 2, 6, 7
Transient Immunity Rl = 2.2 kΩ
at Logic High |VCM| = 10 Vp-p
Level Output
Common Mode |CML| 1000 10000 V/µs IF = 1.6 mA, TA = 25˚C, 6 2, 6, 7
Transient Immunity Rl = 2.2 kΩ
at Logic Low |VCM| = 10 Vp-p
Level Output
*All typical values at TA = 25˚C and VCC = 3.3 V, unless otherwise noted.
Switching Specications (AC)
Over recommended operating conditions (TA = 0°C to 70°C), VCC = 5 V, unless otherwise specied. (See note 8.)
Parameter Sym. Min. Typ.* Max. Units Test Conditions Fig. Note
Propagation Delay tPHL 25 IF = 1.6 mA, RL = 2.2 kΩ 6, 7, 8, 9 2
Time to LogicLow
at Output
Propagation Delay tPLH 50 IF = 1.6 mA, RL = 2.2 kΩ 7, 8, 9 2
Time to Logic High
at Output
Common Mode Transient |CMH| 1000 10000 V/μs IF = 0 mA, TA = 25°C, 10 2, 6, 7
Immunity at Logic RL = 2.2 kΩ
High Output |VCM| = 10 Vp-p
Common Mode Transient |CMH| 1000 10000 V/μs IF = 1.6 mA, TA = 25°C, 10 2, 6, 7
Immunity at Logic RL = 2.2 kΩ
Low Output |VCM| = 10 Vp-p
*All typical values at TA = 25°C and VCC = 5 V, unless otherwise noted.
10
*All typical values at TA = 25˚C, unless otherwise noted.
**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equip-
ment level safety specication or Avago Application Note 1074 entitled "Optocoupler Input-Output Endurance Voltage."
Notes:
1. Pin 5 should be the most negative voltage at the detector side.
2. Each channel.
3. DC CURRENT TRANSFER RATIO (CTR) is dened as the ratio of output collector current, IO, to the forward LED input current, IF, times 100%.
4. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together, and pins 5, 6, 7, and 8 shorted together.
5. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together.
6. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dVCM/dt of the common mode pulse, VCM, to as-
sure that the output will remain in a Logic High state (i.e., VO > 2.0 V). Common mode transient immunity in a Logic Low level is the
maximum tolerable (negative) dVCM/dt of the common mode pulse, VCM, to assure that the output will remain in a Logic Low state
(i.e., VO < 0.8 V).
7. In applications where dV/dt may exceed 50,000 V/µs (such as static discharge) a series resistor, RCC, should be included to protect the detector
IC from destructively high surge currents. The recommended value is RCC = 110 Ω.
8. Use of a 0.1 µF bypass capacitor connected between pins 5 and 8 adjacent to the device is recommended.
9. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 4500 V rms for 1 second (leakage detec-
tion current limit, II-O < 5 µA).
10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 6000 V rms for 1 second (leakage detec-
tion current limit, II-O < 5 µA).
11. Measured between the LED anode and cathode shorted together and pins 5 through 8 shorted together.
12. Derate linearly above 65˚C free-air temperature at a rate of 2.3 mW/˚C for the SO-8 package.
Package Characteristics
Parameter Sym. Device HCPL- Min. Typ.* Max. Units Test Conditions Fig. Note
Input-Output VISO 3750 V rms RH ≤ 50%, 4, 9
Momentary t = 1 min.,
Withstand TA = 25˚C
Voltage**
Resistance RI-O 1012 VI-O = 500 Vdc 4
(Input-Output) RH ≤ 45%
Capacitance CI-O 0.6 pF f = 1 MHz 11
(Input-Output)
Input-Input II-I 0.005 µA RH ≤ 45% 5
Insulation VI-I = 500 Vdc
Leakage Current
Input-Input RI-I 1011 5
Insulation
Leakage Current
Capacitance CI-I 270L 0.03 pF 5
(Input-Input) 273L
070L 0.25
073L
Figure 1. Current transfer ratio vs. forward
current
Figure 3. Output current vs. input diode
forward current
Figure 5. Input diode forward current vs.
forward voltage
Figure 6. Forward voltage vs. temperature
Figure 2. Current transfer ratio vs. forward
current
Figure 4. Output current vs. input diode
forward current
Figure 7. Switching test circuit
IF- FORWARD CURRENT - mA
2500
2000
1000
500
0.1 1.0
CTR - CURRENT TRANSFER RATIO - %
10
1500
0
VCC = 5.0 V
VO= 0.4 V
TA= 25° C
TA= 0°C
TA= 70°C
TA= 85°C
TA= -40°C
IF- INPUT DIODE FORWARD CURRENT - mA
0.01
0.01 0.1 10
IO- OUTPUT CURRENT - mA
0.1
1.0
10
100
TA= 25°C
TA= 0°C
TA= 70°C
TA= 85°C
TA= -40°C
1
IF- INPUT DIODE FORWARD CURRENT - mA
100
10
0.1 0.1 1 10
IO- OUTPUT CURRENT - mA
1.0
TA= 85°C
TA= 25°C
TA= -40°C
VCC = 5.0 V
VO= 0.4 V
VF- FORWARD VOLTAGE - V
100
10
0.1
0.01
1.1 1.2 1.3 1.4
IF- FORWARD CURRENT - mA
1.61.5
1.0
0.001
1000
-
VF
+
TA= 25°C
TA= 0°C
IF
TA= 85°C
TA= 70°C
TA= -40°C
1.6
1.5
1.4
1.3
-60 -20 20 40 100
VF- FORWARD VOLTAGE - V
TA- TEMPERATURE - °C
60 80
0
-40
1.2
IF= 1.6 mA
VO
PULSE
GEN.
Z = 50 W
t = 5 ns
O
r
I MONITOR
F
IF
0.1 µF
L
R
CL= 15 pF*
RM
0
tPHL tPLH
O
V
IF
OL
V
50% 50%
3.3 V
3.3 V
7
1
2
3
45
6
8
10% DUTY CYCLE
I/f < 100 µs
(SATURATED
RESPONSE)
tftr
O
V
(NON-SATURATED
RESPONSE)
3.3 V
90%
10%
90%
10%
* INCLUDES PROBE AND
FIXTURE CAPACITANCE
For product information and a complete list of distributors, please go to our website: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries.
Data subject to change. Copyright © 2005-2008 Avago Technologies Limited. All rights reserved. Obsoletes AV01-0544EN
AV02-1054EN - April 3, 2008
Figure 10. Test circuit for transient immunity and typical waveforms
Figure 9. Test circuit for transient immunity and typical waveforms
Figure 8. Switching test circuit
VO
PULSE GEN.
Z = 50 W
t = 5 ns
O
r
I MONITOR
F
IF
0.1µF
L
R
+5 V
C = 15 pF
L
RM
7
5
6
8
2
3
4
1
1.5 V
5 V
tPHL
O
V
IF
OL
V
05 V
tPLH
1.5 V
OL
V
O
V
IF
VO
IF
L
R
A
B
PULSE GEN.
VCM
+
VFF
O
V
OL
V
O
V
0 V 10%
90% 90%
10%
SWITCH AT A: I = 0 mA
F
SWITCH AT B: I = 1.6 mA
F
CM
V
trtf
3.3 V
+3.3 V
-
7
1
2
3
45
6
8
RCC (SEE NOTE 6)
10 V tr, tf= 16 ns
VO
IF
0.1 µF
L
R
+5 V
A
B
PULSE GEN.
VCM
+-
VFF
CC
R (SEE NOTE 7)
110 W
O
V5 V
OL
V
O
V
10 V
0 V 10% 90% 90% 10%
SWITCH AT A: I = 0 mA
F
SWITCH AT B: I = 1.6 mA
F
CM
V
trtf
t , t = 16 ns
r f 7
5
6
8
2
3
4
1