HYBRID IC VLA513-01R DRIVER FOR IGBT MODULES DESCRIPTION VLA513 is a hybrid integrated circuit designed for driving | OUTLINE DRAWING Dimensions: mm n-channel IGBT modules in any gate-amplifier application. This device operat n isolatio lifier for these modules and perates as an i ion amplifi < 47 MAX Vv. provides the required electrical isolation between the input and output with an opto-coupler. Recommended IGBT modules: Mitsubishi NFH series IGBT modules VCES = 600V series up to 400A class (f : up to 30kHz) VCES = 1200V series up to 400A class (f : up to 30kHz) VCES = 600V series up to 200A class (f : up to 60kHz) VCES = 1200V series up to 200A class (f : up to 60kHz) 0.5 Mitsubishi NF series IGBT modules (f : up to 20kHz) go MAX VCES = 600V series up to 600A class 7 MAX VCES = 1200V series up to 400A class | 284 x rir > < FEATURES High speed switching (Propagation delay time : Typ 0.2us) Output peak current is + / -SA(max) SIP allows more space on mother board Two supply driver (Vcc : 15V , Vee : -10V) Electrical isolation voltage is 2500Vrms(for 1 minute) TTL compatible input interface APPLICATION To drive IGBT modules for welder or induction heating. BLOCK DIAGRAM ee eee mee ee ee | OPTO- | COUPLER | ertcoccttt "7 : 1 | I I . I I Vv INTERFACE : 1 I | tote eeLee a \' 300 ohm | Oe en ee ne en ee ee me ee ee ee ee ee 1MAXIMUM RATINGS (unless otherwise noted, Ta=25C) HYBRID IC VLA513-01R DRIVER FOR IGBT MODULES Symbol Parameter Conditions Ratings Unit Vee Supply voltage DC 18 V Ver -12 Vv ._ | input sonal votage Appled between jin and 200 an |v Vo Output voltage When the output voltage is H Vee Vv lon . 5 A Output current Pulse width 2us, f S 20kHz lotp 5 A Viso Isolation voltage Sine wave voltage 60Hz, for 1min 2500 Vrms Tc Case temperature - 85 C Topr Operating temperature No condensation allowable -20 ~ +70 c Tstg Storage temperature No condensation allowable -25 ~ +100 (*1) C (*1) Differs from H/C condition ELECTRICAL CHARACTERISTICS (unless otherwise noted, Ta=25C, Vcc = 15V, Vee = -10V) Symbol Parameter Conditions - Limits Unit Min | Typ | Max ve Supply voltage Recommended range < 55 Vin Pull-up voltage on primary side Recommended range 4.75 5 5.25 Vv hn H input current Recommended range 9.5 10 14 mA f Switching frequency Recommended range - - 60 kHz Re Gate resistance Recommended range 2 - - ohm lin H input current Vin=5V - 10 - mA Vou H output voltage _ 13 14 - Vv Vor L output voltage _ 8 -9 - Vv teu L-H propagation time ln = 10mMA 0.1 0.2 |] 0.5 ps t L-H rise time In = 10mA - 0.3 1 us tent H-L propagation time lin = 10mMA 0.05 | 0.2 | 0.5 ys t H-L fall time ln = 10mMA - 0.3 1 ysPROPAGATION DELAY TIME L-Ht PLH{ 2s) TOTAL POWER DISSPATION PT(W) HYBRID IC VLA513-01R DRIVER FOR IGBT MODULES PERFORMANCE CURVES t PLH,t PHL vs. Ta CHARACTERISTICS tPLH, tPHL vs, VI CHARACTERISTICS 07 (TYPICAL) (TYPICAL) . - 0.7 Vec=15V Ta=25deg VEE=-10V aH Voo=15V @G 06 FRG=30hm =< 0.6 | VEE=-10V = VIN=5V aE RG=3ohm = LOAD:CM400DU-24NFH 2 LOAD:CM400DU-24NFH a 05 T4105 ~ I 7 of = Ww uw 7 O04 =z 04 w FFE >> Fe 55s 4 . aa . 5 Led 5G S tPLH = 22 t PLH So 02 <= 0.2 E 22 a 0.1 = = 0.1 a a 0.0 0.0 0 10 20 30 40 #50 60 70 ~~ 80 3 4 5 6 7 AMBIENT TEMPERATURE Ta(deg) INPUT SIGNAL VOLTAGE VI(V) PT vs. Ta Ice vs. (Vcc + MEEI ) CHARACTERISTICS (MAXIMUM RATING ) 18 (TYPICAL) 5 T t T RG: 2ohm or more Ta=25deg 45 | Note 1 15 4 a A = 2 3.5 > / 2 Ee 3 Z 10 A 2s z WA . 5 J 2 z Ss Yo 15 a 5 x a a4 { z 1 3 Lm 05 0 0 0 20 40 60 80 100 0 5 10 15 20 25 30 35 AMBIENT TEMPARATURE Ta(deg) SUPPLY VOLTAGE (Vee + IVEEI ) (V) Note 1) Pleage confirm that the following numerical expression is satisfied f =: Switching frequency Refer to Icc vs. Q2: Gate charge on minus bias PT > (Vcc + IVEE! ) * ( ( Q1 + 1021 ) * f + Ico ) Q1: Gate charge on plus bias Ice: Constant dissipation current of driver (Vec + IVEEI) CHARACTERISTICSMeasurement circuit 5V VLA513 oO 220uF 220uF RG u + | HC04 etc. Vec | Vee *Open-collector(drain) is not recommended TT PRECATION HYBRID IC VLA513-01R DRIVER FOR IGBT MODULES CM200DU-24NFH VCC=15V VEE=-10V RG=3o0hm (1) Voltage compensate capacitor are expected to be located as close as possible from the hybrid IC. (2) Please minimize the area of closed circuit of gate circuit so as not to be affected by induction noise. DEFINITION OF CHARACTERISTICS vi Vo t ; tr . . 90% 50% 10% y A tPLH 4 teu!HYBRID Ic VLA513-01R DRIVER FOR IGBT MODULES FOR SAFETY USING Great detail and careful attention are given to the production activity of Hics, such as the development, the quality of production, and in it's reliability. However the reliability of Hics depends not only on their own factors but also in their condition of usage. When handling Hics, please note the following cautions. CAUTIONS Packing The materials used in packing Hics can only withstand normal external conditions. When exposed to outside shocks, rain and certain environmental contaminators, the packing materials will deteriorates. Please take care in handling. Carrying 1) Dont stack boxes too high. Avoid placing heavy materials on boxes. 2) Boxes must be positioned correctly during transportation to avoid breakage. 3) Don't throw or drop boxes. 4) Keep boxes dry. Avoid rain or snow. 5) Minimal vibration and shock during transportation is desirable. Storage When storing Hics, please observe the following notices or possible deterioration of their electrical characteristics, risk of solder ability, and external damage may occur. 1) Devices must be stored where fluctuation of temperature and humidity is minimal, and must not be exposed to direct sunlight. Store at the normal temperature of 5 to 30 degrees Celsius with humidity at 40 to 60%. 2) Avoid locations where corrosive gasses are generated or where much dust accumulates. 3) Storage cases must be static proof. 4) Avoid putting weight on boxes. Extended storage When extended storage is necessary, Hics must be kept non-processed. When using Hics which have been stored for more than one year or under severe conditions, be sure to check that the exterior is free from flaw and other damages. Maximum ratings To prevent any electrical damages, use Hics within the maximum ratings. The temperature, current, valtage, etc. must not exceed these conditions. Polarity To protect Hics from destruction and deterioration due to wrong insertion, make sure of polarity in inserting leads into the board holes, conforming te the external view for the terminal arrangement.HYBRID IC VLA513-01R DRIVER FOR IGBT MODULES STS ISAHAYA ELECTRONICS CORPORATION Marketing division, Marketing planning department 6-41 Tsukuba, Isahaya, Nagasaki, 854-0065 Japan Keep safety first in your circuit designs! ISAHAYA Electronics Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (1)placement of substitutive, auxiliary circuits, (2)use of non-flammable material or (3)prevention against any malfunction or mishap. Notes regarding these materials These materials are intended as a reference to assist our customers in the selection of the ISAHAYA products best suited to the customer's application; they don't convey any license under any intellectual property rights, or any other rights, belonging ISAHAYA or a third party. ' ISAHAYA Electronics Corporation assumes no responsibility for any damage, or infringement of any third party's rights, originating in the use of any product data, diagrams, charts or circuit application examples contained in these materials. : All information contained in these materials, including product data, diagrams and charts, represent information on products at the time of publication of these materials, and are subject to change by ISAHAYA Electronics Corporation without notice due to Product improvements or other reasons. It is therefore recommended that customers contact ISAHAYA Electronics Corporation or an authorized ISAHAYA products distributor for the latest product information before purchasing product listed herein. ISAHAYA Electronics Corporation products are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact ISAHAYA electronics corporation or an authorized ISAHAYA products distributor when considering the use of a product contained herein for any specific purpases, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. + The prior written approval of ISAHAYA Electronics Corporation is necessary to reprint or reproduce in whole or in part these materials. . If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. Please contact ISAHAYA Electronics Corporation or an authorized ISAHAYA products distributor for further details on these materials or the products contained therein. Aug.2005