MITEQ AU-3A-0150 AMPLIFIER FREQUENCY (MHz) 0.3-500 MODEL NUMBER GAIN (dB) (Min.) VAR. (dB) (Max.) VSWR (Max.) IMPED. IN/OUT (Ohms) NOISE FIGURE (dB, Typ.) P1 dB (dBm) (Typ.) AU-3A-0150 44 0.5 2.0:1 50/50 1.4 11 48 15 47 14 75 3 13 46 P1dB Gain (dB) 15 Output -1dB Gain Compression (+dBm) Gain (dB) 45 44 12 11 10 43 9 42 8 0.3 50 100 150 200 250 300 350 400 450 500 0.1 0.3 1.0 10 50 100 200 300 400 500 Frequency (MHz) Frequency (MHz) Input & Output Return Loss (dBRL) Noise Figure (dB) 0 1.5 -5 1.4 Output -10 Noise Figure dB Return Loss NOM. DC POWER OUTLINE VOLTS (mA) NO. -15 -20 -25 Input -30 1.3 1.2 1.1 1.0 0.9 -35 0.8 -40 0.3 50 100 150 200 250 300 350 400 450 10 500 50 100 200 300 400 500 Frequency (MHz) Frequency (MHz) Reverse Isolation (dB) Low Frequency Gain Rolloff (dB) -40 1.0 -45 0.0 Gain Rolloff -55 -60 -65 -70 -1.0 -2.0 -3.0 -75 -4.0 -80 0.3 50 100 150 200 250 300 350 400 450 500 31 65 1000 Frequency (KHz) Frequency (MHz) ISO 9001:2000 Certified 40 * General Infomation * Warranty 100 Davids Drive, Hauppauge, NY 11788 TEL.: (631) 439-9220 * FAX: (631) 436-7430 e-mail: components@miteq.com * www.miteq.com AU-3A-0150 051507 Isolation -50 Gain (dB) 45.0 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 Freq. (MHz) 143 145 148 150 153 155 158 160 163 165 168 170 173 175 178 180 183 185 188 190 193 195 198 200 203 205 208 210 213 215 218 220 223 225 228 230 233 235 238 240 243 245 248 250 253 255 258 260 263 265 268 270 273 275 278 280 283 Gain (dB) 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.2 45.1 45.1 45.1 45.1 45.1 45.1 45.1 45.1 45.1 45.1 45.1 45.1 45.1 45.1 45.1 45.1 45.1 45.1 45.1 45.1 45.1 45.1 45.1 45.1 45.1 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 Freq. (MHz) 285 288 290 293 295 298 300 303 305 308 310 313 315 318 320 323 325 328 330 333 335 338 340 343 345 348 350 353 355 358 360 363 365 368 370 373 375 378 380 383 385 388 390 393 395 398 400 403 405 408 410 413 415 418 420 423 425 Gain (dB) 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 Freq. (MHz) 428 430 433 435 438 440 443 445 448 450 453 455 458 460 463 465 468 470 473 475 478 480 483 485 488 490 493 495 498 500 Gain (dB) 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.1 45.1 45.1 45.1 100 Davids Drive, Hauppauge, NY 11788 TEL.: (631) 439-9220 * FAX: (631) 436-7430 e-mail: components@miteq.com * www.miteq.com AU-3A-0150 051507 Freq. (MHz) 0.3 3 5 8 10 13 15 18 20 23 25 28 30 33 35 38 40 43 45 48 50 53 55 58 60 63 65 68 70 73 75 78 80 83 85 88 90 93 95 98 100 103 105 108 110 113 115 118 120 123 125 128 130 133 135 138 140 MITEQ AU-3A-0150 AMPLIFIER Freq. (MHz) 0.3 3 5 8 10 13 15 18 20 23 25 28 30 33 35 38 40 43 45 48 50 53 55 58 60 63 65 68 70 73 75 78 80 83 85 88 90 93 95 98 100 103 105 108 110 113 115 118 120 123 125 128 130 133 135 138 140 143 145 148 150 153 155 Input VSWR (dBRL) -17 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -17 -17 -17 -17 -17 -17 -17 -17 -17 -17 -17 -17 -17 -17 -17 -17 -18 -18 -18 -18 -18 -18 -18 -18 -18 -18 -18 -18 -18 -18 -19 -19 -19 -19 -19 -19 -19 -19 -19 -19 -19 -20 -20 -20 -20 -20 -20 Output VSWR (dBRL) -20 -32 -34 -35 -35 -34 -34 -33 -33 -32 -32 -31 -30 -30 -29 -29 -29 -28 -28 -27 -27 -27 -26 -26 -26 -26 -25 -25 -25 -24 -24 -24 -24 -24 -23 -23 -23 -23 -22 -22 -22 -22 -22 -22 -21 -21 -21 -21 -21 -21 -21 -20 -20 -20 -20 -20 -20 -20 -20 -19 -19 -19 -19 Freq. (MHz) 158 160 163 165 168 170 173 175 178 180 183 185 188 190 193 195 198 200 203 205 208 210 213 215 218 220 223 225 228 230 233 235 238 240 243 245 248 250 253 255 258 260 263 265 268 270 273 275 278 280 283 285 288 290 293 295 298 300 303 305 308 310 313 Input VSWR (dBRL) -20 -20 -20 -20 -20 -20 -20 -21 -21 -21 -21 -21 -21 -21 -21 -21 -21 -21 -21 -21 -22 -22 -22 -22 -22 -22 -22 -22 -22 -22 -22 -22 -22 -22 -22 -23 -23 -22 -22 -23 -23 -22 -23 -23 -23 -23 -22 -23 -23 -23 -23 -23 -23 -23 -23 -23 -23 -23 -22 -22 -22 -23 -22 Output VSWR (dBRL) -19 -19 -19 -19 -19 -19 -18 -18 -18 -18 -18 -18 -18 -18 -18 -18 -18 -18 -18 -17 -17 -17 -17 -17 -17 -17 -17 -17 -17 -17 -17 -17 -17 -17 -17 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -15 -15 -15 -15 -15 -15 Freq. (MHz) 315 318 320 323 325 328 330 333 335 338 340 343 345 348 350 353 355 358 360 363 365 368 370 373 375 378 380 383 385 388 390 393 395 398 400 403 405 408 410 413 415 418 420 423 425 428 430 433 435 438 440 443 445 448 450 453 455 458 460 463 465 468 470 Input VSWR (dBRL) -22 -22 -23 -22 -22 -22 -22 -22 -22 -22 -22 -22 -22 -22 -22 -22 -22 -22 -22 -22 -21 -21 -21 -21 -21 -21 -21 -21 -21 -21 -21 -21 -20 -20 -20 -20 -20 -20 -20 -20 -20 -20 -19 -19 -19 -19 -19 -19 -19 -19 -19 -19 -19 -19 -18 -18 -18 -18 -18 -18 -18 -18 -18 Output VSWR (dBRL) -15 -15 -15 -15 -15 -15 -15 -15 -15 -15 -15 -15 -15 -15 -15 -15 -15 -15 -15 -15 -15 -15 -15 -15 -15 -15 -15 -15 -15 -15 -15 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 Freq. (MHz) 473 475 478 480 483 485 488 490 493 495 498 500 Input VSWR (dBRL) -17 -17 -17 -17 -17 -17 -17 -17 -17 -16 -16 -16 Output VSWR (dBRL) -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 100 Davids Drive, Hauppauge, NY 11788 TEL.: (631) 439-9220 * FAX: (631) 436-7430 e-mail: components@miteq.com * www.miteq.com AU-3A-0150 051507 MITEQ AU-3A-0150 AMPLIFIER MITEQ AU-3A-0150 AMPLIFIER Reverse Isolation (dB) -63 -63 -63 -63 -63 -63 -62 -63 -62 -62 -63 -63 -62 -62 -63 -63 -63 -62 -63 -62 -62 -63 -62 -62 -63 -63 -62 -62 -62 -63 -63 -62 -63 -63 -62 -62 -63 -62 -62 -63 -62 -62 -62 -62 -62 -62 -63 -62 -62 -62 -62 -62 -62 -62 -61 -63 Freq. (MHz) 140 143 145 148 150 153 155 158 160 163 165 168 170 173 175 178 180 183 185 188 190 193 195 198 200 203 205 208 210 213 215 218 220 223 225 228 230 233 235 238 240 243 245 248 250 253 255 258 260 263 265 268 270 273 275 278 Reverse Isolation (dB) -62 -62 -62 -63 -61 -61 -62 -62 -62 -62 -62 -63 -62 -63 -62 -62 -62 -62 -62 -62 -62 -62 -62 -62 -62 -61 -62 -62 -62 -62 -62 -63 -62 -62 -62 -62 -62 -62 -63 -62 -62 -62 -63 -62 -62 -62 -62 -62 -62 -63 -62 -62 -62 -62 -62 -62 Freq. (MHz) 280 283 285 288 290 293 295 298 300 303 305 308 310 313 315 318 320 323 325 328 330 333 335 338 340 343 345 348 350 353 355 358 360 363 365 368 370 373 375 378 380 383 385 388 390 393 395 398 400 403 405 408 410 413 415 418 Reverse Isolation (dB) -62 -63 -62 -62 -62 -63 -63 -62 -63 -62 -61 -62 -63 -62 -62 -63 -62 -62 -62 -63 -62 -62 -63 -63 -62 -62 -62 -62 -62 -63 -62 -62 -62 -62 -62 -62 -62 -62 -63 -63 -62 -63 -62 -62 -63 -63 -62 -62 -63 -62 -62 -63 -63 -62 -63 -62 Freq. (MHz) 420 423 425 428 430 433 435 438 440 443 445 448 450 453 455 458 460 463 465 468 470 473 475 478 480 483 485 488 490 493 495 498 500 Reverse Isolation (dB) -62 -63 -62 -63 -63 -62 -63 -63 -63 -62 -63 -63 -63 -62 -63 -63 -62 -63 -63 -63 -63 -62 -63 -63 -63 -63 -63 -63 -63 -64 -63 -62 -63 100 Davids Drive, Hauppauge, NY 11788 TEL.: (631) 439-9220 * FAX: (631) 436-7430 e-mail: components@miteq.com * www.miteq.com AU-3A-0150 051507 Freq. (MHz) 0.3 3 5 8 10 13 15 18 20 23 25 28 30 33 35 38 40 43 45 48 50 53 55 58 60 63 65 68 70 73 75 78 80 83 85 88 90 93 95 98 100 103 105 108 110 113 115 118 120 123 125 128 130 133 135 138 MITEQ AU-3A-0150 AMPLIFIER OUTLINE 3 DIM A 2.74 [69.60] DIM B OUNCES 2.54 [64.52] 2.9 100 Davids Drive, Hauppauge, NY 11788 TEL.: (631) 439-9220 * FAX: (631) 436-7430 e-mail: components@miteq.com * www.miteq.com AU-3A-0150 051507 NOTE: DIMENSIONS ARE IN INCHES [MILLIMETERS]. OPTIONS FOR BIPOLAR AMPLIFIERS INPUT BIAS TEE Add Suffix "-F" Used to inject bias signal to photo diode or other type of device. Check for availability on your model before ordering. Available on most units operating above 1 MHz. Please contact MITEQ with your custom requirements. after model number. Example: AU-2A-0150-1334/E will have existing +15 V pin enabled so that it can be used as a test point. Use caution with this option since any voltage applied here will also be present on both the RF output and input center pins. TYPE N OR BNC CONNECTORS Add Suffix "-N" or "-BNC" Type N-female and type BNC-female are available for all outlines 1 through 5, 12, 13 and 15 amplifiers. Add connector type after model number. Examples: AU-2A0150-N; AU-2A-0150-BNC. Type N-male and mixed connector types are also available on request. Please call MITEQ with your specific requirements. BIAS THROUGH THE OUTPUT CONNECTOR Add Suffix "-1306/E" or "-1306/D" INPUT INTERNAL LIMITER Add Suffix "-1103" Used to supply operating power when the amplifier is remotely located while eliminating the need to run a separate DC line. Specify whether existing power pin should be "Enabled" or "Disabled." To order, add -1306/E or -1306/D after model number. Example: AU-2A-0150-1306/E will have existing +15 V pin enabled so that it can be used as a test point. Use caution with this option since any voltage applied here will also be present on the RF output center pin. Available on most units operating above 1 MHz. Available on models up to 500 MHz. Will protect the input stage from CW signals as high as +30 dBm. To order, add "-1103" after model number. Example: AU-2A-0150-1103. Options are available for protection against short duration pulses up to 50 W. Used to supply operating power when the amplifier is remotely located and eliminates the need to run a separate DC line. This DC voltage is then internally fed to the RF input to power a remote LNA or other low power equipment. Maximum current of external load will vary with model type. Available on most units operating above 1 MHz. Please contact factory prior to ordering. RF OUTPUT RF INPUT Available as an add-on to most models using outlines 1 through 5 and 15. Includes 6-foot line cord with standard US line plug, internal fuse, on/off switch and LED indicator light. Amplifier is permanently mounted to power supply. To order, add "-1179" after model number. Example: AU-2A-0150-1179. Refer to outline 12 for dimensions. AC POWER SUPPLY (Wall plug-in unit) Part Number "205531-19" A low cost alternate to option "-1179", the wall plug-in unit is a small switching power supply capable of delivering 1 amp at 15 volts. AC POWER SUPPLY WITH SMC CONNECTORS (Wall plug-in unit) Part Number "-1179SC" Same as above except has mating SMC connectors on amplifier DC input and power supply DC output. Available for outlines 1 through 10, 13 and 15. ADDITIONAL OPTIONS AVAILABLE OPTION BIAS INPUT +V POWER SUPPLY Specify whether existing power pin should be "Enabled" or "Disabled". To order, add "-1334/E" or "-1334/D" Gain Window Phase Match Amplitude Match Gain Control SUFFIX -GW -PM -AM -GC 100 Davids Drive, Hauppauge, NY 11788 TEL.: (631) 439-9220 * FAX: (631) 436-7430 e-mail: components@miteq.com * www.miteq.com AU-3A-0150 051507 BIAS THROUGH THE OUTPUT CONNECTOR WITH DC FEEDTHROUGH TO RF INPUT Add Suffix "-1334/E" or "-1334/D" AC POWER SUPPLY (100 to 240 VAC, 47 - 440 Hz). Add Suffix "-1179" GENERAL INFORMATION PRICING AND TERMS (R) MasterCard (R) A quotation on any item in the catalog is available by contacting the factory. All quotations, unless otherwise noted, are valid for 60 days from the date of issue, F.O.B. (FCA) Hauppauge, NY 11788. Pricing does not include customer or government source inspection unless otherwise noted. On international orders, an irrevocable letter of credit may be required. MITEQ accepts these credit cards: (R) Cards Welcome QUANTITY DISCOUNTS A quantity discount is generally available on most catalog items. Due to the wide variety of devices in the catalog, it is not possible to provide a standard discount schedule. When quantities are involved, please contact the factory and the appropriate information will be provided. SOURCE INSPECTION Government / customer source inspection is available on any item upon receipt of the complete written confirmation of purchase order items, including the prime government contract number. Source inspection with respect to some products increases the unit price and extends delivery because of duplicate standard final inspection and testing. It is recommended wherever possible that a Certificate of Compliance be substituted for source inspection to minimize price and delivery delays. SHIPPING INFORMATION Unless instructed otherwise by the customer, we will ship UPS in the U.S. F.O.B. (FCA) Hauppauge. Air freight will be used as the primary international means of shipment. Please indicate at time of purchase what method of shipment you require. RETURNED MATERIAL When returning material for repair or replacement, please ensure that there is complete information included with the shipment, giving a detailed description of the reason for its return, the date and purchase order on which it was obtained, and the exact address to which the material is to be reshipped. All returns must arrive freight, postage, duties and handling prepaid. REPAIR COSTS Warranty repairs will be made at no cost to the customer. Units out of warranty, or those which have been mishandled, will require approval by the customer for the charges involved before the repairs can be accomplished. We will provide an estimate for the cost of the repair, which can be applied to the repair, if approval is granted. For those items that are deemed beyond repair, or where the customer may decide not to repair the unit, an evaluation fee and handling charge will be applicable. APPLICATION ENGINEERING We maintain a large support staff of engineers who are experts in specific areas of microwave technology. Each has an engineering background that combines both a formal engineering education with training and experience in product design. As further technical support, we make available the services of our engineering and scientific staff, who may be consulted on more advanced circuit designs or application problems. DRAWINGS AND SPECIFICATIONS The material presented in this catalog was current at the time of publication. MITEQ Inc.'s continuing product improvement program makes it necessary to reserve the right to change our mechanical and electrical specifications without notice. If either of these parameters is critical, please contact the factory to verify that the information is current. ADDITIONAL INFORMATION ISO 9001:2000 Certified MITEQ FEDERAL SUPPLY CODE Our Federal Supply Code is: 33592 100 Davids Drive, Hauppauge, NY 11788 TEL.: (631) 439-9220 * FAX: (631) 436-7430 e-mail: components@miteq.com * www.miteq.com AU-3A-0150 051507 WARRANTY