100 Davids Drive, Hauppauge, NY 11788
TEL.: (631) 439-9220 • FAX: (631) 436-7430
e-mail: components@miteq.com • www.miteq.com
AU-3A-0150 051507
MITEQ AU-3A-0150 AMPLIFIER
GAIN VAR. IMPED. NOISE P1 dB NOM. DC
FREQUENCY MODEL (dB) (±dB) VSWR IN/OUT FIGURE (dBm) POWER OUTLINE
(MHz) NUMBER (Min.) (Max.) (Max.) (Ohms) (dB, Typ.) (Typ.) VOLTS (mA) NO.
0.3–500 AU-3A-0150 44 0.5 2.0:1 50/50 1.4 11 15 75 3
Gain (dB)
42
43
44
45
46
47
48
0.3 50 100 150 200 250 300 350 400 450 500
Frequency (MHz)
Gain (dB)
Input & Output Return Loss (dBRL)
-40
-35
-30
-25
-20
-15
-10
-5
0
0.3 50 100 150 200 250 300 350 400 450 500
Frequency (MHz)
dB Return Loss
Reverse Isolation (dB)
-80
-75
-70
-65
-60
-55
-50
-45
-40
0.3 50 100 150 200 250 300 350 400 450 500
Frequency (MHz)
Isolation
Output -1dB Gain Compression (+dBm)
8
9
10
11
12
13
14
15
0.1 0.3 1.0 10 50 100 200 300 400 500
Frequency (MHz)
P1dB
Noise Figure (dB)
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
10 50 100 200 300 400 500
Frequency (MHz)
Noise Figur
e
Low Frequency Gain Rolloff (dB)
-4.0
-3.0
-2.0
-1.0
0.0
1.0
31 40 65 1000
Frequency (KHz)
Gain Rollof
f
Output
Input
7
ISO 9001:2000 Certified • General Infomation • Warranty
100 Davids Drive, Hauppauge, NY 11788
TEL.: (631) 439-9220 • FAX: (631) 436-7430
e-mail: components@miteq.com • www.miteq.com
AU-3A-0150 051507
MITEQ AU-3A-0150 AMPLIFIER
Freq.
(MHz)
Gain
(dB)
0.3 45.0
345.2
545.2
845.2
10 45.2
13 45.2
15 45.2
18 45.2
20 45.2
23 45.2
25 45.2
28 45.2
30 45.2
33 45.2
35 45.2
38 45.2
40 45.2
43 45.2
45 45.2
48 45.2
50 45.2
53 45.2
55 45.2
58 45.2
60 45.2
63 45.2
65 45.2
68 45.2
70 45.2
73 45.2
75 45.2
78 45.2
80 45.2
83 45.2
85 45.2
88 45.2
90 45.2
93 45.2
95 45.2
98 45.2
10045.2
103 45.2
105 45.2
108 45.2
110 45.2
113 45.2
115 45.2
118 45.2
120 45.2
123 45.2
125 45.2
128 45.2
130 45.2
13345.2
135 45.2
138 45.2
140 45.2
Freq.
(MHz)
Gain
(dB)
143 45.2
145 45.2
148 45.2
150 45.2
153 45.2
15545.2
158 45.2
160 45.2
163 45.2
165 45.2
168 45.2
170 45.2
173 45.2
175 45.2
178 45.2
180 45.2
183 45.2
185 45.2
18845.2
190 45.2
193 45.2
195 45.2
198 45.2
20045.2
203 45.1
205 45.1
208 45.1
210 45.1
213 45.1
215 45.1
218 45.1
220 45.1
223 45.1
225 45.1
228 45.1
230 45.1
23345.1
235 45.1
238 45.1
240 45.1
243 45.1
245 45.1
248 45.1
250 45.1
253 45.1
25545.1
258 45.1
260 45.1
263 45.1
265 45.0
268 45.0
270 45.0
273 45.0
275 45.0
278 45.0
280 45.0
283 45.0
Freq.
(MHz)
Gain
(dB)
285 45.0
28845.0
290 45.0
293 45.0
295 45.0
298 45.0
30045.0
303 45.0
305 45.0
308 45.0
310 45.0
313 45.0
315 45.0
318 45.0
320 45.0
323 45.0
325 45.0
328 45.0
330 45.0
333 45.0
335 45.0
338 45.0
340 45.0
343 45.0
345 45.0
348 45.0
350 45.0
353 45.0
35545.0
358 45.0
360 45.0
363 45.0
365 45.0
368 45.0
370 45.0
373 45.0
375 45.0
378 45.0
380 45.0
383 45.0
385 45.0
38845.0
390 45.0
393 45.0
395 45.0
398 45.0
40045.0
403 45.0
405 45.0
408 45.0
410 45.0
413 45.0
415 45.0
418 45.0
420 45.0
423 45.0
425 45.0
Freq.
(MHz)
Gain
(dB)
428 45.0
430 45.0
43345.0
435 45.0
438 45.0
440 45.0
443 45.0
445 45.0
448 45.0
450 45.0
453 45.0
45545.0
458 45.0
460 45.0
463 45.0
465 45.0
468 45.0
470 45.0
473 45.0
475 45.0
478 45.0
480 45.0
483 45.0
485 45.0
48845.0
490 45.0
493 45.1
495 45.1
498 45.1
50045.1
100 Davids Drive, Hauppauge, NY 11788
TEL.: (631) 439-9220 • FAX: (631) 436-7430
e-mail: components@miteq.com • www.miteq.com
AU-3A-0150 051507
MITEQ AU-3A-0150 AMPLIFIER
Freq.
(MHz)
Input
VSWR
(dBRL)
Output
VSWR
(dBRL)
0.3 -17 -20
3 -16 -32
5 -16 -34
8 -16 -35
10 -16 -35
13 -16 -34
15 -16 -34
18 -16 -33
20 -16 -33
23 -16 -32
25 -16 -32
28 -16 -31
30 -16 -30
33 -16 -30
35 -16 -29
38 -16 -29
40 -17 -29
43 -17 -28
45 -17 -28
48 -17 -27
50 -17 -27
53 -17 -27
55 -17 -26
58 -17 -26
60 -17 -26
63 -17 -26
65 -17 -25
68 -17 -25
70 -17 -25
73 -17 -24
75 -17 -24
78 -17 -24
80 -18 -24
83 -18 -24
85 -18 -23
88 -18 -23
90 -18 -23
93 -18 -23
95 -18 -22
98 -18 -22
100 -18 -22
103 -18 -22
105 -18 -22
108 -18 -22
110 -18 -21
113 -18 -21
115 -19 -21
118 -19 -21
120 -19 -21
123 -19 -21
125 -19 -21
128 -19 -20
130 -19 -20
133 -19 -20
135 -19 -20
138 -19 -20
140 -19 -20
143 -20 -20
145 -20 -20
148 -20 -19
150 -20 -19
153 -20 -19
155 -20 -19
Freq.
(MHz)
Input
VSWR
(dBRL)
Output
VSWR
(dBRL)
158 -20 -19
160 -20 -19
163 -20 -19
165 -20 -19
168 -20 -19
170 -20 -19
173 -20 -18
175 -21 -18
178 -21 -18
180 -21 -18
183 -21 -18
185 -21 -18
188 -21 -18
190 -21 -18
193 -21 -18
195 -21 -18
198 -21 -18
200 -21 -18
203 -21 -18
205 -21 -17
208 -22 -17
210 -22 -17
213 -22 -17
215 -22 -17
218 -22 -17
220 -22 -17
223 -22 -17
225 -22 -17
228 -22 -17
230 -22 -17
233 -22 -17
235 -22 -17
238 -22 -17
240 -22 -17
243 -22 -17
245 -23 -16
248 -23 -16
250 -22 -16
253 -22 -16
255 -23 -16
258 -23 -16
260 -22 -16
263 -23 -16
265 -23 -16
268 -23 -16
270 -23 -16
273 -22 -16
275 -23 -16
278 -23 -16
280 -23 -16
283 -23 -16
285 -23 -16
288 -23 -16
290 -23 -16
293 -23 -16
295 -23 -16
298 -23 -16
300 -23 -15
303 -22 -15
305 -22 -15
308 -22 -15
310 -23 -15
313 -22 -15
Freq.
(MHz)
Input
VSWR
(dBRL)
Output
VSWR
(dBRL)
315 -22 -15
318 -22 -15
320 -23 -15
323 -22 -15
325 -22 -15
328 -22 -15
330 -22 -15
333 -22 -15
335 -22 -15
338 -22 -15
340 -22 -15
343 -22 -15
345 -22 -15
348 -22 -15
350 -22 -15
353 -22 -15
355 -22 -15
358 -22 -15
360 -22 -15
363 -22 -15
365 -21 -15
368 -21 -15
370 -21 -15
373 -21 -15
375 -21 -15
378 -21 -15
380 -21 -15
383 -21 -15
385 -21 -15
388 -21 -15
390 -21 -15
393 -21 -14
395 -20 -14
398 -20 -14
400 -20 -14
403 -20 -14
405 -20 -14
408 -20 -14
410 -20 -14
413 -20 -14
415 -20 -14
418 -20 -14
420 -19 -14
423 -19 -14
425 -19 -14
428 -19 -14
430 -19 -14
433 -19 -14
435 -19 -14
438 -19 -14
440 -19 -14
443 -19 -14
445 -19 -14
448 -19 -14
450 -18 -14
453 -18 -14
455 -18 -14
458 -18 -14
460 -18 -14
463 -18 -14
465 -18 -14
468 -18 -14
470 -18 -14
Freq.
(MHz)
Input
VSWR
(dBRL)
Output
VSWR
(dBRL)
473 -17 -14
475 -17 -14
478 -17 -14
480 -17 -14
483 -17 -14
485 -17 -14
488 -17 -14
490 -17 -14
493 -17 -14
495 -16 -14
498 -16 -14
500 -16 -14
100 Davids Drive, Hauppauge, NY 11788
TEL.: (631) 439-9220 • FAX: (631) 436-7430
e-mail: components@miteq.com • www.miteq.com
AU-3A-0150 051507
MITEQ AU-3A-0150 AMPLIFIER
Freq.
(MHz)
Reverse
Isolation
(dB)
0.3 -63
3 -63
5-63
8 -63
10 -63
13 -63
15 -62
18 -63
20 -62
23 -62
25 -63
28 -63
30 -62
33 -62
35 -63
38 -63
40 -63
43 -62
45 -63
48 -62
50 -62
53 -63
55 -62
58 -62
60 -63
63 -63
65 -62
68 -62
70 -62
73 -63
75 -63
78 -62
80 -63
83 -63
85 -62
88 -62
90 -63
93 -62
95 -62
98 -63
100 -62
103 -62
105 -62
108 -62
110 -62
113 -62
115 -63
118 -62
120 -62
123 -62
125 -62
128 -62
130 -62
133 -62
135 -61
138 -63
Freq.
(MHz)
Reverse
Isolation
(dB)
140 -62
143 -62
145 -62
148 -63
150 -61
153 -61
155 -62
158 -62
160 -62
163 -62
165 -62
168 -63
170 -62
173 -63
175 -62
178 -62
180 -62
183 -62
185 -62
188 -62
190 -62
193 -62
195 -62
198 -62
200 -62
203 -61
205 -62
208 -62
210 -62
213 -62
215 -62
218 -63
220 -62
223 -62
225 -62
228 -62
230 -62
233 -62
235 -63
238 -62
240 -62
243 -62
245 -63
248 -62
250 -62
253 -62
255 -62
258 -62
260 -62
263 -63
265 -62
268 -62
270 -62
273 -62
275 -62
278 -62
Freq.
(MHz)
Reverse
Isolation
(dB)
280 -62
283 -63
285 -62
288 -62
290 -62
293 -63
295 -63
298 -62
300 -63
303 -62
305 -61
308 -62
310 -63
313 -62
315 -62
318 -63
320 -62
323 -62
325 -62
328 -63
330 -62
333 -62
335 -63
338 -63
340 -62
343 -62
345 -62
348 -62
350 -62
353 -63
355 -62
358 -62
360 -62
363 -62
365 -62
368 -62
370 -62
373 -62
375 -63
378 -63
380 -62
383 -63
385 -62
388 -62
390 -63
393 -63
395 -62
398 -62
400 -63
403 -62
405 -62
408 -63
410 -63
413 -62
415 -63
418 -62
Freq.
(MHz)
Reverse
Isolation
(dB)
420 -62
423 -63
425 -62
428 -63
430 -63
433 -62
435 -63
438 -63
440 -63
443 -62
445 -63
448 -63
450 -63
453 -62
455 -63
458 -63
460 -62
463 -63
465 -63
468 -63
470 -63
473 -62
475 -63
478 -63
480 -63
483 -63
485 -63
488 -63
490 -63
493 -64
495 -63
498 -62
500 -63
100 Davids Drive, Hauppauge, NY 11788
TEL.: (631) 439-9220 • FAX: (631) 436-7430
e-mail: components@miteq.com • www.miteq.com
AU-3A-0150 051507
OPTIONS FOR BIPOLAR AMPLIFIERS
INPUT BIAS TEE
Add Suffix “-F”
Used to inject bias signal to photo diode or other type
of device. Check for availability on your model before
ordering. Available on most units operating above 1
MHz. Please contact MITEQ with your custom
requirements.
BIAS THROUGH THE OUTPUT CONNECTOR
Add Suffix “-1306/E” or “-1306/D”
Used to supply operating power when the amplifier
is remotely located while eliminating the need to run
a separate DC line. Specify whether existing power
pin should be “Enabled” or “Disabled.” To order, add
-1306/E or -1306/D after model number. Example:
AU-2A-0150-1306/E will have existing +15 V pin
enabled so that it can be used as a test point. Use
caution with this option since any voltage applied here
will also be present on the RF output center pin.
Available on most units operating above 1 MHz.
BIAS THROUGH THE OUTPUT CONNECTOR
WITH DC FEEDTHROUGH TO RF INPUT
Add Suffix “-1334/E” or “-1334/D”
Used to supply operating power when the amplifier is
remotely located and eliminates the need to run a
separate DC line. This DC voltage is then internally
fed to the RF input to power a remote LNA or other
low power equipment. Maximum current of external
load will vary with model type. Available on most units
operating above 1 MHz. Please contact factory prior
to ordering.
Specify whether existing power pin should be
“Enabled” or “Disabled”. To order, add “-1334/E” or “-1334/D”
after model number. Example: AU-2A-0150-1334/E
will have existing +15 V pin enabled so that it can be
used as a test point. Use caution with this option since
any voltage applied here will also be present on both
the RF output and input center pins.
TYPE N OR BNC CONNECTORS
Add Suffix “-N” or “-BNC”
Type N-female and type BNC-female are available for
all outlines 1 through 5, 12, 13 and 15 amplifiers. Add
connector type after model number. Examples: AU-2A-
0150-N; AU-2A-0150-BNC. Type N-male and mixed
connector types are also available on request. Please
call MITEQ with your specific requirements.
INPUT INTERNAL LIMITER
Add Suffix “-1103”
Available on models up to 500 MHz. Will protect the
input stage from CW signals as high as +30 dBm. To
order, add “-1103” after model number. Example:
AU-2A-0150-1103. Options are available for protec-
tion against short duration pulses up to 50 W.
AC POWER SUPPLY (100 to 240 VAC,
47 – 440 Hz). Add Suffix “-1179”
Available as an add-on to most models using outlines
1 through 5 and 15. Includes 6-foot line cord with
standard US line plug, internal fuse, on/off switch and
LED indicator light. Amplifier is permanently mounted
to power supply. To order, add “-1179” after model
number. Example: AU-2A-0150-1179. Refer to outline
12 for dimensions.
AC POWER SUPPLY (Wall plug-in unit)
Part Number “205531-19”
A low cost alternate to option “-1179”, the wall plug-in
unit is a small switching power supply capable of
delivering 1 amp at 15 volts.
AC POWER SUPPLY WITH SMC
CONNECTORS (Wall plug-in unit)
Part Number “-1179SC”
Same as above except has mating SMC connectors
on amplifier DC input and power supply DC output.
Available for outlines 1 through 10, 13 and 15.
ADDITIONAL OPTIONS AVAILABLE
OPTION SUFFIX
Gain Window -GW
Phase Match -PM
Amplitude Match -AM
Gain Control -GC
RF
INPUT
RF
OUTPUT
+V POWER
SUPPLY
BIAS
INPUT
100 Davids Drive, Hauppauge, NY 11788
TEL.: (631) 439-9220 • FAX: (631) 436-7430
e-mail: components@miteq.com • www.miteq.com
AU-3A-0150 051507
PRICING AND TERMS
A quotation on any item in the catalog is available by contacting the factory. All
quotations, unless otherwise noted, are valid for 60 days from the date of issue,
F.O.B. (FCA) Hauppauge, NY 11788. Pricing does not include customer or gov-
ernment source inspection unless otherwise noted. On international orders, an
irrevocable letter of credit may be required. MITEQ accepts these credit cards:
QUANTITY DISCOUNTS
A quantity discount is generally available on most catalog items. Due to the
wide variety of devices in the catalog, it is not possible to provide a standard discount schedule. When quantities are involved,
please contact the factory and the appropriate information will be provided.
SOURCE INSPECTION
Government / customer source inspection is available on any item upon receipt of the complete written confirmation of purchase
order items, including the prime government contract number. Source inspection with respect to some products increases the
unit price and extends delivery because of duplicate standard final inspection and testing. It is recommended wherever possi-
ble that a Certificate of Compliance be substituted for source inspection to minimize price and delivery delays.
SHIPPING INFORMATION
Unless instructed otherwise by the customer, we will ship UPS in the U.S. F.O.B. (FCA) Hauppauge. Air freight will be used as
the primary international means of shipment. Please indicate at time of purchase what method of shipment you require.
RETURNED MATERIAL
When returning material for repair or replacement, please ensure that there is complete information included with the shipment,
giving a detailed description of the reason for its return, the date and purchase order on which it was obtained, and the exact
address to which the material is to be reshipped. All returns must arrive freight, postage, duties and handling prepaid.
REPAIR COSTS
Warranty repairs will be made at no cost to the customer. Units out of warranty, or those which have been mishandled, will
require approval by the customer for the charges involved before the repairs can be accomplished. We will provide an estimate
for the cost of the repair, which can be applied to the repair, if approval is granted. For those items that are deemed beyond
repair, or where the customer may decide not to repair the unit, an evaluation fee and handling charge will be applicable.
APPLICATION ENGINEERING
We maintain a large support staff of engineers who are experts in specific areas of microwave technology. Each has an engi-
neering background that combines both a formal engineering education with training and experience in product design. As
further technical support, we make available the services of our engineering and scientific staff, who may be consulted on
more advanced circuit designs or application problems.
DRAWINGS AND SPECIFICATIONS
The material presented in this catalog was current at the time of publication. MITEQ Inc.’s continuing product improvement pro-
gram makes it necessary to reserve the right to change our mechanical and electrical specifications without notice. If either of
these parameters is critical, please contact the factory to verify that the information is current.
GENERAL INFORMATION
ADDITIONAL INFORMATION
Welcome
Cards
®
MasterCard
®
®
®
MITEQ FEDERAL SUPPLY CODE
Our Federal Supply Code is: 33592
WARRANTY ISO 9001:2000 Certified
