B65662B0000T001 - EPCOS - Datasheet.Live

Ferrites and accessories

Series/Type: P 22 x 13

The following products presented in this data sheet are being withdrawn.

Ordering Code Substitute Product Date of

Withdrawal

Deadline Last

Orders

Last Shipments

B65662A5000X000 2010-09-24 2010-12-27 2011-03-28

For further information please contact your nearest EPCOS sales office, which will also support

you in selecting a suitable substitute. The addresses of our worldwide sales network are

presented at www.epcos.com/sales.

210/09

Please read Cautions and warnings and

Important notes at the end of this document.

■To IEC 60133

■Delivery mode: sets

Magnetic characteristics (per set)

Approx. weight (per set)

Gapped

Ungapped

with

center hole

without

center hole

l/A

Amin

0.5

31.6

—

1990

0.46

33.2

72.6

58.1

2410

mm–1

mm2

mm3

m1314g

Material AL value

approx.

eOrdering code 1)

-D with center hole

-N with threaded sleeve

N48 160 3% 0.50 64 B65661+0160A048

250 3% 0.26 100 B65661+0250A048

315 3% 0.22 126 B65661+0315A048

630 3% 0.10 251 B65661+0630A048

1250 5% 0.05 499 B65661D1250J048

Material AL value

ePV

W/set

Ordering code

-D with center hole

-W without center hole

K1 220 +30/–20% 88 B65661D0000R001

N48 3800 +30/–20% 1520 B65661D0000R048

N30 8300 +30/–20% 3020 B65661W0000R030

T38 16000 +40/–30% 5820 B65661W0000Y038

N87 4400 +30/–20% 1600 < 1.1 (200 mT, 100 kHz, 100 °C) B65661W0000R087

FPK0118-Q

2.9±0.15

0.5+0.2

9.2+0.4

0.4

13.6

ø4.4+0.2

0.3ø9.4

13.9 0.6

3.9+0.6

17.9+0.6

0.822

1) Replace the + by the code letter ”D“ or ”N“ for the required version.

B65661Core

P 22  13

310/09

Please read Cautions and warnings and

Important notes at the end of this document.

Coil former

Standard: to IEC 60133

Material: GFR polyterephthalate (UL 94 V-0, insulation class to IEC 60085:

F max. operating temperature 155 °C), color code black

Valox 420-SE0® E45329 (M), GE PLASTICS B V

Winding: see Data Book 2007, chapter “Processing notes, 2.1”

Insulating washer between core and coil former

■For tolerance compensation and for insulation

■Polycarbonate spring washer (UL 94 V-0, insulation class to IEC 60085: E 120 °C), 0.08 mm thick

Aryphan F685, E167358 (M), natural color, LOFO HIGH TECH FILM GMBH

Coil former

Insulating washer

Coil former Ordering code

Sections AN

mm2

AR value



1 23.4 44 67 B65662B0000T001

Insulating washer (reel packing, PU = 1 reel) B65662A5000X000

17.8

0.2

2.5+0.8

0.6

0.15

ø10.7

0.15

ø9.6+0.15

FPK0352-H

(preliminary data)

B65662Accessories

P 22  13

410/09

Please read Cautions and warnings and

Important notes at the end of this document.

Adjusting screw

■Tube core with thread and core brake made of GFR polyterephthalate

Pocan B3235® E245249 (M), LANXESS AG

Tube core Ordering code

  length (mm) Material Color code

3.85  5.0 N22 gray B65812B3003X022

B65812Accessories

P 22  13

510/09

Ferrites and accessories

Cautions and warnings

Mechanical stress and mounting

Ferrite cores have to meet mechanical requirements during assembling and for a growing number

of applications. Since ferrites are ceramic materials one has to be aware of their special behavior

under mechanical load.

Just like any ceramic material, ferrite cores are brittle and sensitive to any shock, fast changing or

tensile load. Especially fast cooling rates under ultrasonic cleaning, high static and cyclic loads can

cause cracks or failure of the ferrite cores.

For detailed information see Data Book 2007, chapter "General - Definitions, 8.1".

Effects of core combination on AL value

Stresses in the core affect not only the mechanical but also the magnetic properties. It is apparent

that the initial permeability is dependent on the stress state of the core. The higher the stresses are

in the core, the lower the value for the initial permeability. Thus, the embedding medium should offer

the greatest possible elasticity.

For detailed information see Data Book 2007, chapter "General - Definitions, 8.2".

Heating up

Ferrites can run hot during operation at higher flux densities and higher frequencies.

NiZn-materials

The magn etic properties of NiZn-materials c an change irreversibly when exp osed to strong

magnetic fields.

Processing notes

– The start of the winding process should be soft. Otherwise, the flanges may be destroyed.

– Excessive winding forces may damage the flanges or squeeze the tube so that the cores can no

longer be mounted.

– Excessive sold ering time at high temperat ure (>300 ° C) ma y aff ect coplanarity or pin

arrangement.

– Not following the p rocessing notes for soldering of the J-leg terminals may cause so lderability

problems at the transformer because of contamination with tin oxide (SnO) from the tin bath or

burned insu lation from the wire . For detailed information see Data Boo k 20 07, chapter

"Processing notes, 2.2".

– The dimensions o f the pin hole arrangement are fixed and should b e understood as an ideal

recommendation for drilling the printed circuit board. In order to avoid problems when mounting

the transformer, customers should make allowances for manufacturing tolerances in the drilling

and pick-and-place processes by increasing the diameter of the pin holes.

610/09

Important notes

The following applies to all products named in this publication:

1. Some parts of th is publication contain statements about the suitability of our products for

certain areas of application. T hese statements are based o n our knowledge of typical

requirements that are often placed on our products in the areas of application concerned. We

nevertheless exp ressly point out that such statements cannot be regarded as binding

statements about the suitability of our products for a particular customer application. As

a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them

than the customers the mselves. F or these reasons , it is always ultimately incumbent on the

customer to check and decide whether an EPCOS product with the properties described in the

product specification is suitable for use in a particular customer application.

2. We a lso point out that in individual cases, a malfunction of electronic components or

failure before the end of their usual service life cannot be completely ruled out in the

current state of the art, even if they are operated as specified. In customer applications

requiring a very high level of operational safety and especially in customer applications in which

the malfunction or failure of an electronic component could endanger human life or health (e.g.

in accident prevention or life-saving systems), it must therefore be ensured by means of suitable

design of the cust omer application or oth er action taken by t he customer (e.g. installation of

protective circuitry or redundancy) that no injury or damage is sustaine d by third parties in the

event of malfunction or failure of an electronic component.

3. The warnings, cautions and product-specific notes must be observed.

4. In order to satisfy certain technical requirements, some of the products described in this

publication may contain substances subject to restrictions in certain jurisdictions (e.g.

because they are classed as hazardous). Useful information on this will be found in our

Material Data Sheets on the Internet (www .epcos.com/material). Should you have any more

detailed questions, please contact our sales offices.

5. We constantly strive to improve our products. C onsequently, the products described in this

publication may change from time to time. The same is tru e of the corresponding product

specifications. Please check therefore to w hat extent product descriptions and specifications

contained in this publication are still applicable before or when you place an order.

We als o reserve the right to discontinue production and delivery of products.

Consequently, we cannot guarantee that all pro ducts named in this publication will always be

available. The aforementio ned does not apply in the case of individual agre ements deviating

from the foregoing for customer-specific products.

6. Unless otherwise agreed in individual contracts, all orders are subject to the current version

of the “General Terms of Delivery for Products and Services in the Electrical Industry”

published by the German Electrical and Electronics Industry Association (ZVEI).

7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DSSP, MiniBlue,

MiniCell, MKK, MLSC, MotorCap, PCC , PhaseCap, Pha seCube, PhaseMod, PhiCap,

SIFERRIT, SIFI, SIKOREL, Sil verCap, SIMDAD , SIMID, SineFormer, SIOV, SIP5D, SIP5K,

ThermoFuse, WindC ap are trademarks registered or pending in Europe and in other

countries. Further information will be found on the Internet at www.epcos.com/trademarks.