Specification Control Drawing
WIRE, HALOGEN FREE, THIN WALL INSULATED,
250 VOLT AC IN ACCORDANCE WITH NF F 63-808, TEMPERATURE CLASSIFICATION 105°C
(Suitable for use at an operating voltage of 750/1300 VOLTS AC)
Conductor -
Insulation -
Tin Plated Copper Halogen Free
Polymer
C8
C9
C14
C11
C16
C17
C18
C21
C20
Part Nominal Nominal Conductor
Description Cross Conductor Diameter Minimum Maximum Nominal Maximum Base
Sectional Stranding (mm) Insulation Resistance Weight Weight Colour
Area No./Diam. Thickness @ 20°C Lower Upper (kg/km) (kg/km)
(mm²) (mm) (mm) (ohms/km) Spec Target Spec
Min. Max. Limit Limit
#100F0111-22 0.38 19/0.16 0.74 0.76 0.20 50.5 1.26 1.29 1.34 4.46 4.63 *
100F0111-20 0.60 19/0.20 0.96 0.98 0.20 30.0 1.47 1.51 1.55 6.86 7.10 yellow
100F0111-18 0.93 19/0.25 1.21 1.24 0.20 20.0 1.70 1.75 1.80 10.5 10.8 white
100F0111-16 1.34 19/0.30 1.45 1.48 0.20 13.7 1.99 2.04 2.10 13.9 14.9 green
100F0111-14 1.82 37/0.25 1.68 1.72 0.20 9.80 2.30 2.36 2.45 19.8 20.7 yellow
100F0111-12 2.61 37/0.30 2.03 2.08 0.25 7.00 2.62 2.70 2.79 26.4 27.6 white
100F0111-10 4.32 61/0.30 2.53 2.90 0.25 4.46 3.29 3.38 3.51 43.8 47.0 green
COLOUR Insulation colour determined by conductor cross sectional area, as defined above.
CODE: '*' = Insulation colour determined by customer order.
PERFORMANCE The complete requirements for procuring the wire described herein shall consist
REQUIREMENTS: of this document and NF F 63-808 Mai 1992 except where indicated.
MARKING: Marking shall be vertically (longitudinally NF F Spec),
REQUIREMENT: spaced at 100 mm minimum to 150mm maximum, coloured black
Legend: 'E $ - NF F 63-808 - TE Raychem - YY'
Where:
"$" = the conductor cross sectional area (see above)
and "YY" = the Year Code Designator in accordance with the table below.
e.g. 'E 0.93 - NF F 63-808 - TE Raychem - 09' reflects
100F0111-18 manufactured in 2009.
N.B. When used as a component, the mark is defined by the cable SCD.
100F0111-22 only is marked as follows: 'E 0.38 - TE Raychem - YY'
where "YY" = the Year Code Designator in accordance with the table above.
APPROVAL: Electronic sign off - no signatures will appear.
''Raychem', 'TE' and 'Tyco Electronics' are registered trademarks of Tyco Electronics Corporation.
©2009 Tyco Electronics Corporation. All International Rights Reserved.
N/A
'#' This size is not covered by NF F 63-808 but except as stated, is tested to the requirements of NF F 63-808 Mai 1992.
E 250 S 1.82-NF F 63-808
FINISHED WIRE
Page 2 is for internal use only
E 250 S 0.60-NF F 63-808
E 250 S 0.93-NF F 63-808
E 250 S 1.34-NF F 63-808
100F0111
Issue 9
27th May 2009
Page 1 of 2
Diameter
(mm)
E 250 S 2.61-NF F 63-808
E 250 S 4.32-NF F 63-808
NF F 63-808
Designation
