P6SMB SERIES Surface Mount Transient Voltage Suppressor Voltage Range 6.8 to 200 Volts 600 Watts Peak Power SMB/DO-214AA Features For surface mounted application in order to optimize board space Low profile package Built-in strain relief Glass passivated junction Excellent clamping capability Fast response time: Typically less than 1.0ps from 0 volt to BV min. Typical IR less than 1A above 10V High temperature soldering guaranteed: 260OC / 10 seconds at terminals Plastic material used carries Underwriters Laboratory Flammability Classification 94V-0 600 watts peak pulse power capability with a 10 x 1000 us waveform by 0.01% duty cycle .082(2.08) .076(1.93) .147(3.73) .137(3.48) .187(4.75) .167(4.25) .012(.31) .006(.15) .103(2.61) .078(1.99) .012(.31) .006(.15) Mechanical Data .056(1.41) .035(0.90) Case: Molded plastic Terminals: Solder plated Polarity: Indicated by cathode band Standard packaging: 12mm tape (EIA STD RS-481) Weight: 0.093gram .008(.20) .004(.10) .208(5.28) .200(5.08) Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25ambient temperature unless otherwise specified. Type Number O Peak Power Dissipation at TA=25 C, Tp=1ms(Note 1) Steady state Power Dissipation Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method) (Note 2, 3) - Unidirectional Only Maximum Instantaneous Forward Voltage at 50.0A for Unidirectional Only (Note 4) Typical Thermal Resistance (Note 5) Operating and Storage Temperature Range Symbol Value Units PPK Minimum 600 Watts Pd 3 Watts IFSM 100 Amps VF 3.5/5.0 Volts RJC RJA TJ, TSTG 10 55 -65 to + 150 O C/W O C O Notes: 1. Non-repetitive Current Pulse Per Fig. 3 and Derated above TA=25 C Per Fig. 2. 2 2. Mounted on 5.0mm (.013 mm Thick) Copper Pads to Each Terminal. 3. 8.3ms Single Half Sine-wave or Equivalent Square Wave, Duty Cycle=4 pulses Per Minute Maximum. 4. VF=3.5V on P6SMB6.8 thru P6SMB91 Devices and VF=5.0V on SMBJ100 thru SMBJ200 Devices. 5. Measured on P.C.B. with 0.27" x 0.27"(7.0mm x 7.0mm) Copper Pad Areas. Devices for Bipolar Applications 1. For Bidrectional Use C or CA Suffix for Types P6SMB6.8 through Types P6SMB200A. 2. Electrical Characteristics Apply in Both Directions. - 550 - ELECTRICAL CHARACTERISTICS (TA=25OC unless otherwise noted) Device Device Marking Code Breakdown Voltage Test Stand-Off Maximum Maximum Maximum Maximum Current Voltage Reverse Leakage Peak Pulse Clamping Temperature VBR @IT VWM at VWM Current IRSM Voltage at IPPM Coefficient (Volts) (Note 1) O Min Max (mA) (Volts) ID (uA) (Note 2)(Amps) VC(Volts) of VBR(% / C) P6SMB6.8 KDJ 6.12 7.48 10 5.50 1000 58 10.8 0.057 P6SMB6.8A KEJ 6.45 7.14 10 5.80 1000 60 10.5 0.057 0.061 P6SMB7.5 KFJ 6.75 8.25 10 6.05 500 53 11.7 P6SMB7.5A KGJ 7.13 7.88 10 6.40 500 55 11.3 0.061 P6SMB8.2 KHJ 7.38 9.02 10 6.63 200 50 12.5 0.065 P6SMB8.2A KKJ 7.79 8.61 10 7.02 200 52 12.1 0.065 P6SMB9.1 KLJ 8.19 10.0 1.0 7.37 50 45 13.8 0.068 P6SMB9.1A KMJ 8.65 9.55 1.0 7.78 50 47 13.4 0.068 P6SMB10 KNJ 9.00 11.0 1.0 8.10 10 42 15.0 0.073 P6SMB10A KPJ 9.50 10.5 1.0 8.55 10 43 14.5 0.073 P6SMB11 KQJ 9.90 12.1 1.0 8.92 5.0 38 16.2 0.075 P6SMB11A KRJ 10.5 11.6 1.0 9.40 5.0 40 15.6 0.075 P6SMB12 KSJ 10.8 13.2 1.0 9.72 5.0 36 17.3 0.078 P6SMB12A KTJ 11.4 12.6 1.0 10.2 5.0 37 16.7 0.078 P6SMB13 KUJ 11.7 14.3 1.0 10.5 5.0 33 19.0 0.081 P6SMB13A KVJ 12.4 13.7 1.0 11.1 5.0 34 18.2 0.081 P6SMB15 KWJ 13.5 16.5 1.0 12.1 5.0 28 22.0 0.084 P6SMB15A KXJ 14.3 15.8 1.0 12.8 5.0 29 21.2 0.084 P6SMB16 KYJ 14.4 17.6 1.0 12.9 5.0 26 23.5 0.086 P6SMB16A KZJ 15.2 16.8 1.0 13.6 5.0 28 22.5 0.086 P6SMB18 LDJ 16.2 19.8 1.0 14.5 5.0 23 26.5 0.088 P6SMB18A LEJ 17.1 18.9 1.0 15.3 5.0 25 25.2 0.088 P6SMB20 LFJ 18.0 22.0 1.0 16.2 5.0 21 29.1 0.090 P6SMB20A LGJ 19.0 21.0 1.0 17.1 5.0 22 27.7 0.090 P6SMB22 LHJ 19.8 24.2 1.0 17.8 5.0 19 31.9 0.092 P6SMB22A LKJ 20.9 23.1 1.0 18.8 5.0 20 30.6 0.092 P6SMB24 LLJ 21.6 26.4 1.0 19.4 5.0 18 34.7 0.094 P6SMB24A LMJ 22.8 25.2 1.0 20.5 5.0 19 33.2 0.094 P6SMB27 LNJ 24.3 29.7 1.0 21.8 5.0 16 39.1 0.096 P6SMB27A LPJ 25.7 28.4 1.0 23.1 5.0 16.8 37.5 0.096 P6SMB30 LQJ 27.0 33.0 1.0 24.3 5.0 14 43.5 0.097 0.097 P6SMB30A LRJ 28.5 31.5 1.0 25.6 5.0 15 41.4 P6SMB33 LSJ 29.7 36.3 1.0 26.8 5.0 13.0 47.7 0.098 P6SMB33A LTJ 31.4 34.7 1.0 28.2 5.0 13.8 45.7 0.098 P6SMB36 LUJ 32.4 39.6 1.0 29.1 5.0 12 52.0 0.099 P6SMB36A LVJ 34.2 37.8 1.0 30.8 5.0 12.6 49.9 0.099 P6SMB39 LWJ 35.1 42.9 1.0 31.6 5.0 11.1 56.4 0.100 0.100 P6SMB39A LXJ 37.1 41.0 1.0 33.3 5.0 11.6 53.9 P6SMB43 LYJ 38.7 47.3 1.0 34.8 5.0 10.0 61.9 0.101 P6SMB43A LZJ 40.9 45.2 1.0 36.8 5.0 10.6 59.3 0.101 P6SMB47 MDJ 42.3 51.7 1.0 38.1 5.0 9.2 67.8 0.101 P6SMB47A MEJ 44.7 49.4 1.0 40.2 5.0 9.7 64.8 0.101 P6SMB51 MFJ 45.9 56.1 1.0 41.3 5.0 8.5 73.5 0.102 P6SMB51A MGJ 48.5 53.6 1.0 43.6 5.0 8.9 70.1 0.102 P6SMB56 MHJ 50.4 61.6 1.0 45.4 5.0 7.8 80.5 0.103 P6SMB56A MKJ 53.2 58.8 1.0 47.8 5.0 8.1 77.0 0.103 P6SMB62 MLJ 55.8 68.2 1.0 50.2 5.0 7.0 89.0 0.104 P6SMB62A MMJ 58.9 65.1 1.0 53.0 5.0 7.4 85.0 0.104 P6SMB68 MNJ 61.2 74.8 1.0 55.1 5.0 6.4 98.0 0.104 P6SMB68A MPJ 64.6 71.4 1.0 58.1 5.0 6.8 92.0 0.104 P6SMB75 MQJ 67.5 82.5 1.0 60.7 5.0 5.8 108.0 0.105 P6SMB75A MRJ 71.3 78.8 1.0 64.1 5.0 6.1 103.0 0.105 P6SMB82 MSJ 73.8 90.2 1.0 66.4 5.0 5.3 118.0 0.105 P6SMB82A MTJ 77.9 86.1 1.0 70.1 5.0 5.5 113.0 0.105 - 551 - ELECTRICAL CHARACTERISTICS (TA=25OC unless otherwise noted) Device Device Marking Code Breakdown Volta Test Stand-Off Maximum Maximum Maximum Maximum VBR Current Voltage Reverse Leakage Peak Pulse Clamping Temperature (Volts) (Note 1 @IT VWM at VWM Current IRSM Voltage at IPPM Coefficient O Min Max (mA) (Volts) ID (uA) (Note 2)(Amps) VC(Volts) of VBR(% / C) P6SMB91 MUJ 81.9 100.0 1.0 73.7 5.0 4.8 131.0 0.106 P6SMB91A MVJ 86.5 95.5 1.0 77.8 5.0 5.0 125.0 0.106 P6SMB100 MWJ 90.0 110.0 1.0 81.0 5.0 4.3 144.0 0.106 P6SMB100A MXJ 95.0 105.0 1.0 85.5 5.0 4.5 137.0 0.106 P6SMB110 MYJ 99.0 121.0 1.0 89.2 5.0 3.9 158.0 0.107 P6SMB110A MZJ 105.0 116.0 1.0 94.0 5.0 4.1 152.0 0.107 P6SMB120 NDJ 108.0 132.0 1.0 97.2 5.0 3.6 173.0 0.107 P6SMB120A NEJ 114.0 126.0 1.0 102.0 5.0 3.8 165.0 0.107 P6SMB130 NFJ 117.0 143.0 1.0 105.0 5.0 3.3 187.0 0.107 P6SMB130A NGJ 124.0 137.0 1.0 111.0 5.0 3.5 179.0 0.107 P6SMB150 NHJ 135.0 165.0 1.0 121.0 5.0 2.9 215.0 0.108 P6SMB150A NKJ 143.0 158.0 1.0 128.0 5.0 3.0 207.0 0.108 P6SMB160 NLJ 144.0 176.0 1.0 130.0 5.0 2.7 230.0 0.108 P6SMB160A NMJ 152.0 168.0 1.0 136.0 5.0 2.8 219.0 0.108 P6SMB170 NNJ 153.0 187.0 1.0 138.0 5.0 2.5 244.0 0.108 P6SMB170A NPJ 162.0 179.0 1.0 145.0 5.0 2.6 234.0 0.108 P6SMB180 NQJ 162.0 198.0 1.0 146.0 5.0 2.4 258.0 0.108 P6SMB180A NRJ 171.0 189.0 1.0 154.0 5.0 2.5 246.0 0.108 P6SMB200 P6SMB200A NSJ NTJ 180.0 190.0 220.0 210.0 1.0 1.0 162.0 171.0 5.0 5.0 2.1 2.2 287.0 274.0 0.108 0.108 Notes: 1. VBR measured after IT applied for 300us, IT=square wave pulse or equivalent. 2. Surge current waverform per Figure 3 and derate per Figure 2. 3. For bipolar types having VWM of 10 volts and under, the ID limit is doubled. 4. For bidirectional use C or Ca suffix for types P6SMB6.8 through P6SMB200A. 5. All terms and symbols are consistent with ANSI/IEEE C62.35. - 552 - NON-REPETITIVE PULSE WAVEFORM SHOWN in FIG.3 O TA = 25 C 10 1.0 0.1 0.1 s 1.0 s 10 s 100 s 1.0ms 10ms tp, PULSE WIDTH, sec. 150 Peak Value IPPM 100 td 0 0 1.0 2.0 3.0 4.0 t, TIME, ms ID, INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES 50 25 0 0 25 50 75 100 125 150 175 FIG.5- TYPICAL REVERSE LEAKAGE CHARACTERASTICS FIG.4- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT UNIDIRECTIONAL ONLY 8.3ms Single Half Sine Wave JEDEC Method 10 1 10 100 NUMBER OF CYCLES AT 60Hz FIG.6- TYPICAL JUNCTION CAPACITANCE UNIDIRECTIONAL 1,000 6,000 MEASURED at ZERO BIAS 100 10 MEASURED AT DEVICES STAND-OFF VOLTAGE, VWM 1 0.1 0.01 O TA = 25 C 0.001 0 100 200 300 V(BR), BREAKDOWN VOLTAGE. VOLTS 400 200 O TA, AMBIENT TEMPERATURE. ( C) 100 Half Value - IPPM 2 10/1000 sec. WAVEFORM as DEFINED by R.E.A. 50 75 200 PULSE WIDTH (td) is DEFINED as the POINT WHERE the PEAK CURRENT DECAYS to 50% of IPPM tr = 10 sec 100 IFSM, PEAK FORWARD SURGE CURRENT. AMPERES PEAK PULSE CURRENT - % FIG.3- PULSE WAVEFORM FIG.2- PULSE DERATING CURVE 500 CJ,JUNCTION CAPACITANCE. (pF) PPPM, PEAK PULSE POWER, KW FIG.1- PEAK PULSE POWER RATING CURVE 100 PEAK PULSE POWER (PPP) or CURRENT (IPPM) DERATING IN PERCENTAGE. % RATINGS AND CHARACTERISTIC CURVES (P6SMB SERIES) 1,000 O Tj =25 C f = 1.0MHz Vsig = 50 mVp-p MEASURED at STAND-OFF VOLTAGE, VWM 100 10 1.0 10 100 V(BR), BREAKDOWN VOLTAGE. VOLTS - 553 - 200