MVAD065 Series
65W 2" x 4" AC-DC Power Supply Converter
MVAD065.B01 Page 1 of 7
power.murata.com
For full details go to
www.murata-ps.com/rohs
For full details go to
www.murata-ps.com/rohs
www.murata-ps.com
FEATURES
ITE (2nd Ed.) and Medical (3rd ed.) MOPP
safety approved
55-65W compact high density
2" x 4" standard footprint
High efficiency up to 90%
Remote Sense
Universal AC input
Low profile - 1U package
Convection-cooled operation up to 65W
Complies with 5000m altitude
RoHS compliant
Input power < 74W
UL Class I and II approved
Less than 0.3W no load input power
Complies with ErP/Energy Star requirement
excluding 5V output
ORDERING GUIDE
Model Number Natural Convection Cooling Main Output (V1)
MVAD065-05 55W 5V
MVAD065-12 60W 12V
MVAD065-18 18V
MVAD065-24 65W 24V
MVAD065-48 48V
INPUT CHARACTERISTICS
Parameter Conditions Min. Typ. Max. Units
Input Voltage Operating Range Single phase 90 120/230 264 Vac
DC 120 300 Vdc
Input Frequency 47 50/60 63 Hz
Turn-on Input Voltage Input rising at full load 70 85 Vac
Turn-off Input Voltage Input falling at full load 70 85
Input Current 90Vac input, full load 1.4 A
Inrush Current 5V At 264Vac, at 25°C cold start 75 Apk
Other 60
OUTPUT CHARACTERISTICS
Model Number Main Output
Voltage (V1) Load Current Load Capacitance Line, Load, Cross
Regulation
Typical Efficiency
@230Vac full load
MVAD065-05 5V 0 to 11A 0 to 2200μF ± 2% 84%
MVAD065-12 12V 0 to 5.0A 0 to 1000µF ± 2% 88%
MVAD065-18 18V 0 to 3.34A 0 to 680μF ± 2% 86%
MVAD065-24 24V 0 to 2.71A 0 to 560µF ± 2% 89%
MVAD065-48 48V 0 to 1.36A 0 to 330µF ± 2% 90%
MAIN OUTPUT CHARACTERISTICS
Parameter Conditions Min. Max. Units
5V Other
Transient Response 50% load step, 1A/µsec slew rate ±5 %
Settling Time to 1% of Nominal 500 200 µsec
Turn On Delay After application of input power 1 sec
Output Voltage Rise Monotonic, 0 to 100% load 50 msec
Setpoint Accuracy 120Vac, 40W, 25°C ±1 ±0.5 %
Output Holdup 115Vac, 100% load 10 msec
Temperature Coefficient 0.02 %/°C
Ripple Voltage & Noise
1
2 1 %
Remote Sense
3
Compensates for up to 400mV
of lead drop with remote sense
connected. Protected against short
circuit and reverse connection.
400 mV
1. Ripple and noise are measured with 0.1 uF of ceramic capacitance and 47 uF of electrolytic capacitance on each
of the power supply outputs. The output noise requirements apply over a 0 Hz to 20 MHz bandwidth. A short
coaxial cable with 50ohm scope termination is used.
2. Unless otherwise specified all readings are taken at 120Vac input and 25°C ambient temperature.
3. 0.4V lead drop is compensated in remote sense.
DESCRIPTION
The MVAD065 series switching power supplies utilize advanced component and circuit technologies
to deliver high efficiency. Designed for Medical, Telecom, and Industrial applications to satisfy 1U
height design considerations, the MVAD065 Series measures only 2.0” x 4.0” x 1.3”. All models offer
universal AC input and compliance to worldwide safety and EMC standards.
CB
Test Certicate
and Test Report
REG.-Nr. C457
Available now at
http://power.murata.com/acdc3d
*LAST TIME BUY: 2/28/2019. CLICK HERE FOR DISCONINUANCE NOTICES.
MVAD065 Series
65W 2" x 4" AC-DC Power Supply Converter
MVAD065.B01 Page 2 of 7
power.murata.com
ENVIRONMENTAL CHARACTERISTICS
Parameter Conditions Min. Typ. Max. Units
Storage Temperature Range -40 85
°C
Operating Temperature Range See thermal derating curves -10 70
Start up -20
Operating Humidity Non-condensing 10 95 %
Operating Altitude For Class I ITE Equipment deployment -200 5000 m
Other -200 2000
MTBF Telcordia SR-332 M1C3 25°C 1M Hours
Shock
Operating, IEC60068-2-27, half-sine 5G, 6ms,
3 times per face, 6 faces Complies
Non-operating, IEC60068-2-27, half-sine,
30G, 18ms, 3 times per face, 6 faces Complies
Vibration
Operating, IEC60068-2-6, 1.0G, 10-150Hz, 10
minutes per axis, on all 3 axes Complies
Non-operating, IEC60068-2-6, 2.0G,
10-150Hz, 10 minutes per axis, on all 3 axes Complies
Safety
IEC60950-1:2005 (2nd Edition); Am1:2009
UL60950-1 2nd Edition,2011-12-19, CSA C22.2 No. 60950-1-07, 2nd Edition,2011-12
EN60950-1:2006 + A11:2009 + A1:2010 + A12:2011
IEC60601-1:2005 + CORR.1(2006) + CORR.2(2007)
ANSI/AAMI ES60601-1 (2005+C1:09 + A2:10), CSA-C22.2 No. 60601-1(2008), MOPP
CE Marking per LVD
Warranty 2 years
Outside Dimensions 2.0" x 4.0" x 1.3" (50.8mm x 101.6mm x 33.02mm)
Weight
MVAD065-05 / MVAD065-18 0.285lbs (130g) typical
Other 0.27lbs (123g) typical
PROTECTION CHARACTERISTICS
Parameter Conditions Min. Typ. Max. Units
Overvoltage Protection MVAD065-05 Latching (50% load) 110 190 %V1
Other Latching (60% load) 110 160
Overcurrent Protection Hiccup mode 110 160 %A
ISOLATION CHARACTERISTICS
Parameter Conditions Min. Typ. Max. Units
Isolation
Primary to Earth Ground (1xMOPP) 1500 Vac
Primary to Secondary (2xMOPP)44000
Secondary to Earth Ground 500 Vdc
Leakage Current (under normal conditions) 240Vac, 60Hz, 25°C 300
µA264Vac, 60Hz, 25°C 350
Touch Current 264Vac, 60Hz, 25°C 100
EMISSIONS AND IMMUNITY
Characteristic Standard Compliance
Input Current Harmonics IEC/EN 61000-3-2 Class A
Voltage Fluctuation and Flicker IEC/EN 61000-3-3 Complies
Conducted Emissions EN 55022 Class B, Class A (at Class II equipment)
FCC Part 15 Class B, Class A (at Class II equipment)
ESD Immunity IEC/EN 61000-4-2 Level 4, Criterion A
Radiated Field Immunity IEC/EN 61000-4-3 Level 2, Criterion A
Electrical Fast Transient Immunity IEC/EN 61000-4-4 Level 3, Criterion A
Surge Immunity IEC/EN 61000-4-5 Level 4, Criterion A
RF Conducted Immunity IEC/EN 61000-4-6 Level 2, Criterion A
Magnetic Field Immunity IEC/EN 61000-4-8 Level 2, Criterion A
Voltage dips, interruptions IEC/EN 61000-4-11 Level 3, Criterion B
4. At class I equipment.
EMI CONSIDERATIONS
For optimum EMI performance, the power supply should be mounted to a metal plate grounded to all 4 mounting holes of the power supply. To comply with
safety standards, this plate must be properly grounded to protective earth (see mechanical dimension notes). Pre-compliance testing has shown the stand-
alone power supply to comply with EN55022 class A radiated emissions. Radiated emission results vary with system enclosure and cable routing paths.
PERFORMANCE DATA
MVAD065 Series
65W 2" x 4" AC-DC Power Supply Converter
MVAD065.B01 Page 3 of 7
power.murata.com
Output Current (A)
MVAD065-05 Efficiency (%)
73
75
77
79
81
83
85
87
89
91
93
0.00 2.00 4.00 6.00 8.00 10.00 12.00
90Vac
115Vac
230Vac
264Vac 75
77
79
81
83
85
87
89
91
93
95
0.00 1.00 2.00 3.00 4.00 5.00
Output Current (A)
MVAD065-12 Efficiency (%)
90Vac
115Vac
230Vac
264Vac
Output Current (A)
MVAD065-18 Efficiency (%)
75
77
79
81
83
85
87
89
91
93
95
0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 4.00
90Vac
115Vac
230Vac
264Vac
75
77
79
81
83
85
87
89
91
93
95
0.00 0.20 0.40 0.60 0.80 1.00 1.20 1.40
Output Current (A)
MVAD065-48 Efficiency (%)
90Vac
115Vac
230Vac
264Vac
75
77
79
81
83
85
87
89
91
93
95
0.00 0.50 1.00 1.50 2.00 2.50 3.00
Output Current (A)
MVAD065-24 Efficiency (%)
90Vac
115Vac
230Vac
264Vac
SAFETY CONSIDERATIONS
1. This power supply is a component level power supply intended for use in class I or class II applications. Secondary ground traces need to be suit-
ably isolated from primary ground traces when used in class II applications.
2. When the power supply is used in class II equipment, all ground traces and components connected to the primary side are considered primary for
spacing and insulation considerations.
3. Double pole/neutral fusing.
PERFORMANCE DATA
MVAD065 Series
65W 2" x 4" AC-DC Power Supply Converter
MVAD065.B01 Page 4 of 7
power.murata.com
Inrush waveform (AC264V 25°C)
0
10
20
30
40
50
60
10-10 30 50
Output power (W)
70
Ambient temp. ( )
MVAD065-05 Thermal Derang
0
20
40
60
80
100
10-10 30 50
Output power (%)
Thermal Derang (Other)
70
Ambient temp. ( )
MVAD065 Series
65W 2" x 4" AC-DC Power Supply Converter
MVAD065.B01 Page 5 of 7
power.murata.com
MECHANICAL DIMENSIONS – MVAD065-05 ONLY
Dimensions: 2.0" x 4.0" x 1.3" (50.8mm x 101.6mm x 33.02mm)
All dimensions in inches (mm). tolerance is +/-0.02’ (0.5)
Mounting holes H1 and H2 should be earth-grounded for EMI purpose
Mounting holes H2 is earth ground connection
This power supply requires mounting on standoffs minimum 0.2' (5.0) in height
Output Voltage Adjust Pot
for Factory Use
※1 Preferred screw type
Φ0.156±0.05
4 Places
Maximum Screw Head DIAMETER
Maximum earth ground contact area
PCB top and bottom
DIAMETER Φ0.236" (6.0)
M3 (Metric screw threads)
No.4-40UNC (United thread Standard)
INPUT/OUTPUT CONNECTOR AND SIGNAL SPECIFICATION AND MATING CONNECTORS
PIN Description Mating Housing Crimp terminal/pins
Input Connector CN1 : Molex 26-62-4030
Molex 09-50-8031 with locking ramp Molex 6838 Series
1 AC Line (V-)
3 AC Neutral (V+)
Spade Connector: #250
GND Earth Ground
Output Connector CN2 : Molex 26-60-4060
Molex 09-50-8061 with locking ramp Molex 6838 Series
1, 2 V1
3, 4 DC Return
5 -Remote Sense (NC)
6 +Remote Sense
MVAD065 Series
65W 2" x 4" AC-DC Power Supply Converter
MVAD065.B01 Page 6 of 7
power.murata.com
MECHANICAL DIMENSIONS – MVAD065-12x ONLY
Dimensions: 2.0" x 4.0" x 1.3" (50.8mm x 101.6mm x 33.02mm)
All dimensions in inches (mm). tolerance is +/-0.02’ (0.5)
Mounting holes H1 and H2 should be earth-grounded for EMI purpose
Mounting holes H2 is earth ground connection
This power supply requires mounting on standoffs minimum 0.2' (5.0) in height
INPUT/OUTPUT CONNECTOR AND SIGNAL SPECIFICATION AND MATING CONNECTORS
PIN Description Mating Housing Crimp terminal/pins
Input Connector CN1 : Molex 26-62-4030
Molex 09-50-8031 with locking ramp Molex 6838 Series
1 AC Line (V-)
3 AC Neutral (V+)
Spade Connector: #250
GND Earth Ground
Output Connector CN2 : Molex 26-60-4060
Molex 09-50-8061 with locking ramp Molex 6838 Series
1, 2 V1
3, 4 DC Return
5 -Remote Sense (NC)
6 +Remote Sense
MVAD065 Series
65W 2" x 4" AC-DC Power Supply Converter
MVAD065.B01 Page 7 of 7
power.murata.com
Murata Manufacturing Co., Ltd. Power Device Product Division
Nagaokakyo-shi, Kyoto 617-8555 Japan
ISO 9001 and 14001 REGISTERED
This product is subject to operating requirements and the Life and
Safety Critical Application Policy. Click here to view policy.
Please contact us regarding restricted materials compliance beyond
the RoHS directive.
Murata makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or
sell equipment constructed in accordance therewith. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards that anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might
cause harm, and take appropriate remedial actions. Buyer will fully indemnify Murata, its affiliated companies, and its representatives against any damages arising out of the use of any Murata products in safety-critical applications. Specifications are subject to change without notice.
© 2015 Murata Manufacturing Co., Ltd. All Rights Reserved.
MECHANICAL DIMENSIONS – MVAD065-xx 24V and 48V MODELS
Dimensions: 2.0" x 4.0" x 1.3" (50.8mm x 101.6mm x 33.02mm)
All dimensions in inches (mm). tolerance is +/-0.02’ (0.5)
Mounting holes H1 and H2 should be earth-grounded for EMI purpose
Mounting holes H2 is earth ground connection
This power supply requires mounting on standoffs minimum 0.2' (5.0) in height
INPUT/OUTPUT CONNECTOR AND SIGNAL SPECIFICATION AND MATING CONNECTORS
PIN Description Mating Housing Crimp terminal/pins
Input Connector CN1 : Molex 26-62-4030
Molex 09-50-8031 with locking ramp Molex 6838 Series
1 AC Line (V-)
3 AC Neutral (V+)
Spade Connector: #250
GND Earth Ground
Output Connector CN2 : Molex 26-60-4060
Molex 09-50-8061 with locking ramp Molex 6838 Series
1, 2 V1
3, 4 DC Return
5 -Remote Sense (NC)
6 +Remote Sense
