PTN
www.vishay.com Vishay Dale Thin Film
Revision: 18-Nov-11 1Document Number: 60026
For technical questions, contact: thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Commercial Thin Film Chip Resistor,
Surface Mount Chip
These chip resistors are available in both “top side” and
“wraparound” termination styles in a variety of sizes. They
incorporate self passivated, enhanced Tantalum Nitride
films, to give superior performance on moisture resistance,
voltage coefficient, power handling and resistance stability.
The terminations consist of an adhesion layer, a leach
resistant nickel barrier, and solder coating. This product will
out-perform all requirements of characteristic E of
MIL-PRF-55342.
CONSTRUCTION
FEATURES
• Moisture resistant
• High purity alumina substrate
• Non-standard values available
• Will pass + 85 °C, 85 % relative humidity and
10 % rated power
• 100 % visual inspected per MIL-PRF-55342
• Non-inductive
• Very low noise and voltage coefficient (< - 30 dB)
• Laser-trimmed tolerances to ± 0.1 %
• Wraparound resistance less than 10 m
• Epoxy bondable termination available
• Sulfur resistant (per ASTM B809-95 humid vapor test)
• Compliant to RoHS Directive 2002/95/EC
Notes
*Pb containing terminations are not RoHS compliant, exemptions
may apply
** Please see document “Vishay Material Category Policy”:
www.vishay.com/doc?99902
TYPICAL PERFORMANCE
Note
(1) 0705 and 0805 are the same (only use 0805 when ordering)
Actual Size
1505
Adhesion Layer
High Purity
Alumina Substrate
Nickel Barrier
Solder
Coating
Passivation
T antalum Nitride
Resistive Film
ABSOLUTE
TCR 25
TOL. 0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST SPECIFICATIONS CONDITIONS
Material Tantalum nitride -
Resistance Range 10 to 3 M-
TCR: Absolute ± 25 ppm/°C to ± 100 ppm/°C - 55 °C to + 125 °C
Tolerance: Absolute ± 0.1 % to ± 5 % + 25 °C
Stability: Absolute R ± 0.03 % 2000 h at 70 °C
Stability: Ratio --
Voltage Coefficient 0.1 ppm/V -
Working Voltage 75 V to 200 V -
Operating Temperature Range - 55 °C to + 125 °C -
Storage Temperature Range - 55 °C to + 150 °C -
Noise < - 30 dB -
Shelf Life Stability: Absolute --
COMPONENT RATINGS
CASE SIZE (1) POWER RATING (mW) WORKING VOLTAGE (V) RESISTANCE RANGE ()
0402 50 75 20 to 35K
0502 100 75 20 to 65K
0505 150 75 20 to 130K
0603 150 75 10 to 120K
0705 200 100 10 to 301K
0805 200 100 10 to 301K
1005 250 100 10 to 360K
1010 500 150 50 to 600K
1206 400 200 10 to 1M
1505 400 150 10 to 1M
2208 750 150 10 to 1.75M
2010 800 200 10 to 2M
2512 1000 200 10 to 3M
PTN
www.vishay.com Vishay Dale Thin Film
Revision: 18-Nov-11 2Document Number: 60026
For technical questions, contact: thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Note
(1) 0705 and 0805 are the same (only use 0805 when ordering)
DIMENSIONS in inches
CASE SIZE L W T D E
0402 0.042 ± 0.008 0.022 ± 0.005 0.012 to 0.033 0.010 ± 0.005 0.010 ± 0.005
0502 0.055 ± 0.006 0.025 ± 0.005 0.012 to 0.033 0.010 ± 0.005 0.015 ± 0.005
0505 0.055 ± 0.006 0.050 ± 0.005 0.012 to 0.033 0.010 ± 0.005 0.015 ± 0.005
0603 0.064 ± 0.006 0.032 ± 0.005 0.020 max. 0.012 ± 0.005 0.015 ± 0.005
0705, 0805 (1) 0.080 ± 0.006 0.050 ± 0.005 0.015 to 0.033 0.015 ± 0.005 0.015 ± 0.005
1005 0.105 ± 0.007 0.050 ± 0.005 0.015 to 0.033 0.015 ± 0.005 0.015 ± 0.005
1010 0.105 ± 0.007 0.100 ± 0.005 0.015 to 0.033 0.015 ± 0.005 0.015 ± 0.005
1206 0.126 ± 0.008 0.063 ± 0.005 0.015 to 0.033 0.020 + 0.005/ - 0.010 0.020 + 0.005/ - 0.010
1505 0.155 ± 0.007 0.050 ± 0.005 0.015 to 0.033 0.015 ± 0.005 0.015 ± 0.005
2010 0.209 ± 0.009 0.098 ± 0.005 0.015 to 0.033 0.020 ± 0.005 0.020 ± 0.005
2208 0.230 ± 0.007 0.075 ± 0.005 0.015 to 0.033 0.020 ± 0.005 0.020 ± 0.005
2512 0.259 ± 0.009 0.124 ± 0.005 0.015 to 0.033 0.020 ± 0.005 0.020 ± 0.005
ENVIRONMENTAL TESTS (Vishay Performance vs. MIL-PRF-55342 Requirements)
ENVIRONMENTAL TEST LIMITS MIL-PRF-55342
CHARACTERISTIC “E”
TYPICAL VISHAY
PERFORMANCE
Resistance Temperature Characteristic ± 25 ppm/°C ± 15 ppm/°C
Max. Ambient Temp. at Rated Wattage + 70 °C + 70 °C
Max. Ambient Temp. at Power Derating + 150 °C + 150 °C
Thermal Shock R± 0.1 % ± 0.040 %
Low Temperature Operation R± 0.1 % ± 0.001 %
Short Time Overload R± 0.10 % ± 0.002 %
High Temperature Exposure R± 0.1 % ± 0.04 %
Resistance to Soldering Heat R± 0.2 % ± 0.008 %
Moisture Resistance R± 0.2 % ± 0.004 %
Life + 70 °C at 1000 h R± 0.50 % ± 0.02 %
Insulation Resistance 10 000 minimum > 100 000 M
D
W
L
T
E
PTN
www.vishay.com Vishay Dale Thin Film
Revision: 18-Nov-11 3Document Number: 60026
For technical questions, contact: thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Note
(1) Preferred packaging code
FILM LOAD LIFE STABILITY (at + 125 °C)
0.1 %
0.06 %
0.05 %
0.04 %
0.03 %
0.02 %
0.01 %
0.006 %
0.005 %
0.004 %
0.003 %
0.002 %
0.001 %
1000 1200 1400 1600 1800 2000
Time in h at + 125 °C
Maximum
Absolute
Change
800600400200
DERATING CURVE
Ambient Temperature °C
0 70 125 150
0
20
40
60
80
100
Percent of Rated Power
GLOBAL PART NUMBER INFORMATION
New Global Part Numbering: PTN1206E1002BBT1
GLOBAL
MODEL
CASE
SIZE
TCR
CHARACTERISTIC RESISTANCE TOLERANCE TERMINATION PACKAGING
PTN 0402
0502
0505
0603
0805
1005
1010
1206
1505
2208
2010
2512
E= ± 25 ppm/°C
H= ± 50 ppm/°C
K= ± 100 ppm/°C
The first 3 digits are
significant figures
and the last digit
specifies the number
of zeros to follow.
“R” designates the
decimal point.
Example:
10R0 = 10
1000 = 100
1001 = 1 k
B= ± 0.1 %
D= ± 0.5 %
F= ± 1 %
G= ± 2 %
J= ± 5 %
B = Wraparound
Sn/Pb solder
Sn63
w/nickel barrier
G = Wraparound Au
over Ni (gold)
termination
epoxy bondable
RoHS compliant - e4
S = Wraparound lead
(Pb)-free solder
96.5 % Sn/3.0 % Ag/
0.5 % Cu
RoHS compliant - e1
BS = BULK
100 min., 1 mult
WS = WAFFLE
100 min., 1 mult
W0 = WAFFLE
100 min., 100 mult
TAPE AND REEL
T0 = 100 min., 100 mult
T1 = 1000 min., 1000 mult (1)
T3 = 300 min., 300 mult
T5 = 500 min., 500 mult
TF = Full reel
TS = 100 min., 1 mult
Historical Part Number example: PTN0805H8801BBT (for reference purposes only)
PTN 0805 H 8801 B B T
STYLE CASE SIZE
TCR
CHARACTERISTIC
OHMIC VALUE TOLERANCE TERMINATION PACKAGING
06E1 02B01 BT1NPT 2
Document Number: 91000 www.vishay.com
Revision: 11-Mar-11 1
Disclaimer
Legal Disclaimer Notice
Vishay
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.