SCOPE: POWER MOSFET DRIVER Device Type 01 02 Generic Number MAX4429M(x)/883B MAX4420M(x)/883B Circuit Function Inverting Power MOSFET Driver Noninverting Power MOSFET Driver Case Outline(s). The case outlines shall be designated in Mil-Std-1835 and as follows: Outline Letter JA LP Mil-Std-1835 GDIP1-T8 or CDIP2-T8 CQCC1-N20 Case Outline Package Code 8 LEAD CERDIP J8 20 Leadless Carrier LCC Absolute Maximum Ratings Supply Voltage VDD to GND ................................................................................... 20V Input Voltage ............................................................................VS +0.3V to GND -5.0V Output Current (per pin capacitance load) .............................................................. 6.0A Peak Supply Current or GND current (per pin) ...................................................... 6.0A Lead Temperature (soldering, 10 seconds) ................................................................... +300C Storage Temperature ...................................................................................... -65C to +150C Continuous Power Dissipation .............................................................................. TA=+70C 8 pin CERDIP(derate 8.0mW/C above +70C) ........................................................ 640mW 20 pin LCC(derate 9.1mW/C above +70C) ............................................................ 727mW Junction Temperature TJ ......................................................................................... +150C Thermal Resistance, Junction to Case, JC 8 pin CERDIP..................................................................................................... 55C/W 20 pin LCC ........................................................................................................ 20C/W Thermal Resistance, Junction to Ambient, JA: 8 pin CERDIP................................................................................................... 125C/W 20 pin LCC ...................................................................................................... 110C/W Recommended Operating Conditions Ambient Operating Range (TA) ............................................................ -55C to +125C Package 8 pin CERDIP 20 pin LCC 8 pin CERDIP 20 pin LCC ORDERING INFORMATION: MAX4429MJA/883B MAX4429MLP/883B MAX4420MJA/883B MAX4420MLP/883B SMD Number 5962-8877002PA 5962-88770022A 5962-8877003PA 5962-88770032A Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ---------------------------- Electrical Characteristics of MAX4420 and MAX4429 for /883B and SMD 5962-88770 19-0250 Page 2 of Rev. C 5 TABLE 1. ELECTRICAL TESTS: TEST CONDITIONS -55 C <=TA<= +125C 4.5VVS18V Unless otherwise specified Symbol Input Voltage Range Logic 1 Input Voltage Logic 0 Input Voltage Input Current VIN(max) VIH VIL IIN Group A Subgroup 1,2,3 1,2,3 1,2,3 1,2,3 -5VVIN0V Output High Voltage Output Low Voltage VOH VOL RL= RL= Output Resistance RO1 VS=18V, IOUT=10mA, VIN=0.8V RO2 1 2,3 1,2,3 1,2,3 1 NOTE 1 NOTE 1 IS1 VIN=+3V Quiescent Supply Current IS2 VIN=0V Rise Time NOTE 2 tR VS=18V, CL=2500pF Fall Time NOTE 2 tF VS=18V, CL=2500pF Delay Time NOTE 2 tD1 VS=18V, CL=2500pF Delay Time NOTE 2 tD2 VS=18V, CL=2500pF All All All -5.0 2.4 Limits Max Units VS+0.3 V V V mA 0.8 10 1 10 All All 01 02 VDD-25 25 2.8 2.5 A mV mV 2,3 All 5.0 1 01 02 2.5 2.8 2,3 All 5.0 1 2,3 1 2,3 9 10,11 9 10,11 9 10,11 9 10,11 01 1.5 3.0 0.15 0.4 35 60 35 60 75 100 75 100 VS=18V, IOUT=10mA, VIN=2.4V Quiescent Supply Current Limits Min All 0VVINVS Output Resistance Device type 01 All All All All mA mA ns ns ns ns NOTE 1: Guaranteed by design. NOTE 2: Subgroups 10 and 11 are guaranteed if not tested to the limits specified in Table 1. See Figure 1. FIGURE 1: See Commercial Datasheet, Switching-Time Measurement Circuit. TERMINAL CONNECTIONS FOR 01 AND 02. 8 Lead CERDIP 20 Lead LCC 1 VS 1 NC 11 2 INPUT 2 NC 12 3 NC 3 VS 13 4 GND 4 NC 14 5 GND 5 NC 15 6 OUTPUT 6 INPUT 16 7 OUTPUT 7 NC 17 8 VS 8 NC 18 9 GND 19 10 NC 20 ---------------------------- NC NC GND NC OUTPUT OUTPUT NC NC VS NC Electrical Characteristics of MAX4420 and MAX4429 for /883B and SMD 5962-88770 19-0250 Page 3 of Rev. C 5 QUALITY ASSURANCE Sampling and inspection procedures shall be in accordance with MIL-Prf-38535, Appendix A as specified in MilStd-883. Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015: 1. Test Condition, A, B, C, or D. 2. TA = +125C minimum. 3. Interim and final electrical test requirements shall be specified in Table 2. Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883, including Groups A, B, C, and D inspection. Group A inspection: 1. Tests as specified in Table 2. 2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted. Group C and D inspections: a. End-point electrical parameters shall be specified in Table 1. b. Steady-state life test, Method 1005 of Mil-Std-883: 1. Test condition A, B, C, D. 2. TA = +125C, minimum. 3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883. TABLE 2. ELECTRICAL TEST REQUIREMENTS Mil-Std-883 Test Requirements Interim Electric Parameters Method 5004 Final Electrical Parameters Method 5005 Group A Test Requirements Method 5005 Group C and D End-Point Electrical Parameters Method 5005 * ** Subgroups per Method 5005, Table 1 1 1*, 2, 3, 9, 10**, 11** 1, 2, 3, 9, 10**, 11** 1 PDA applies to Subgroup 1 only. Subgroups 10 and 11, if not tested shall be guaranteed to the limits specified in Table 1. ---------------------------- Electrical Characteristics of MAX4420 and MAX4429 for /883B and SMD 5962-88770 19-0250 Page 4 of Rev. C 5