SCOPE: POWER MOSFET DRIVER
Device Type Generic Number Circuit Function
01 MAX4429M(x)/883B Inverting Power MOSFET Driver
02 MAX4420M(x)/883B Noninverting Power MOSFET Driver
Case Outline(s). The case outlines shall be designated in Mil-Std-1835 and as follows:
Outline Letter Mil-Std-1835 Case Outline Package Code
JA GDIP1-T8 or CDIP2-T8 8 LEAD CERDIP J8
LP CQCC1-N20 20 Leadless Carrier LCC
A bsolute Maximum Ratings
Supply Voltage VDD to GND ................................................................................... 20V
Input Voltage ............................................................................VS +0.3V to GND -5.0V
Output Current (per pin capacitance load) .............................................................. 6.0A
Peak Supply Current or GND current (per pin) ...................................................... 6.0A
Lead Temperature (soldering, 10 seconds) ................................................................... +300°C
Storage Temperature ...................................................................................... -65°C to +150°C
Continuous Power Dissipation .............................................................................. TA=+70°C
8 pin CERDIP(derate 8.0mW/°C above +70°C) ........................................................ 640mW
20 pin LCC(derate 9.1mW/°C above +70°C) ............................................................ 727mW
Junct ion Temperature TJ ...........................................................................…........... +150°C
Thermal Resista nce, J unction to Case, ΘJC
8 pin CERDIP..................................................................................................... 55°C/W
20 pin LCC ........................................................................................................ 20°C/W
Thermal Resistance, Junction to Ambient, ΘJA:
8 pin CERDIP................................................................................................... 125°C/W
20 pin LCC ...................................................................................................... 110°C/W
Recommended Operating Co ndit ions
Ambient Operating Range (TA) ............................................................ -55°C to +125°C
Package ORDERING INFORMATION: SMD Number
8 pin CERDIP MAX4429MJA/883B 5962-8877002PA
20 pin LCC MAX4429MLP/883B 5962-88770022A
8 pin CERDIP MAX4420MJA/883B 5962-8877003PA
20 pin LCC MAX4420MLP/883B 5962-88770032A
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those indicated in the operational section s of the sp ecifica tions is not implied. Exposure to ab solute maximum
rating conditions for extended periods may affect device reliability.
---------------------------- Electrical Characteristics of MAX4420 and MAX4429 19-0250 Rev. C
for /883B and SMD 5962-88770 Page 2 of 5
TABLE 1. ELECTRICAL TESTS:
TEST Symbol
CONDITIONS
-55 °C <=TA<= +125°C
4.5V≤VS≤18V
Unless otherwise specified
Group A
Subgroup Device
type Limits
Min Limits
Max Units
Input Voltage Range VIN(max) 1,2,3 All -5.0 VS+0.3 V
Logic 1 Input Voltage VIH 1,2,3 All 2.4 V
Logic 0 Input Voltage VIL 1,2,3 All 0.8 V
Input Current IIN -5V≤VIN≤0V
0V≤VIN≤VS
1,2,3
1
2,3
All ±10
±1
±10
mA
µA
Output High Voltage VOH RL=∞ NOTE 1 1,2,3 All VDD-25 mV
Output Low Voltage VOL RL=∞ NOTE 1 1,2,3 All 25 mV
Output Resistance RO1 VS=18V, IOUT=10mA, VIN=0.8V
1
2,3
01
02
All
2.8
2.5
5.0 Ω
Output Resistance RO2 VS=18V, IOUT=10mA, VIN=2.4V
1
2,3
01
02
All
2.5
2.8
5.0 Ω
Quiescent Suppl y Current IS1 VIN=+3V 1
2,3 01 1.5
3.0 mA
Quiescent Suppl y Current IS2 VIN=0V 1
2,3 01 0.15
0.4 mA
Rise Time NOTE 2 tRVS=18V, CL=2500pF 9
10,11 All 35
60 ns
Fall Time NOTE 2 tFVS=18V, CL=2500pF 9
10,11 All 35
60 ns
Delay Time NOTE 2 tD1 VS=18V, CL=2500pF 9
10,11 All 75
100 ns
Delay Time NOTE 2 tD2 VS=18V, CL=2500pF 9
10,11 All 75
100 ns
NOTE 1: Guaranteed by design.
NOTE 2: Subgroups 10 and 11 are guaranteed if not tested to the limits specified in Table 1.
See Figure 1.
FIGURE 1: See Commercial Datasheet, Switching-Time Measurement Circuit.
TERMINAL CONNECTIONS FOR 01 AND 02.
8 Lead CERDIP 20 Lead LCC
1 VS 1 NC 11 NC
2INPUT 2 NC 12 NC
3 NC 3 VS 13 GND
4 GND 4 NC 14 NC
5 GND 5 NC 15 OUTPUT
6 OUTPUT 6 INPUT 16 OUTPUT
7 OUTPUT 7 NC 17 NC
8 VS 8 NC 18 NC
9 GND 19 VS
10 NC 20 NC
---------------------------- Electrical Characteristics of MAX4420 and MAX4429 19-0250 Rev. C
for /883B and SMD 5962-88770 Page 3 of 5
QUALITY ASSURAN CE
Sampling and inspection procedures shall be in accordance with MIL-Prf-38535, Appendix A as specified in Mil-
Std-883.
Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015:
1. Test Condition, A, B, C, or D.
2. TA = +125°C minimum.
3. Interim and final electrical test requirements shall be specified in Table 2.
Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883, including Groups A, B,
C, and D inspection.
Group A inspection:
1. Tests as specified in Table 2.
2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted.
Group C and D inspections:
a. End-point electrical parameters shall be specified in Table 1.
b. Steady-state life test, Method 1005 of Mil-Std-883:
1. Test condition A, B, C, D.
2. TA = +125°C, minimum.
3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883.
TABLE 2. ELECTRICAL TEST REQUIREMENTS
Mil-Std-883 Test Requirements Subgroups
per Method 5005, Table 1
Interim Electric Parameters
Method 5004 1
Final Electrical Parameters
Method 5005 1*, 2, 3, 9, 10**, 11**
Group A Test Requirements
Method 5005 1, 2, 3, 9, 10**, 11**
Group C and D End-Point Electrical Parameters
Method 5005 1
* PDA applies to Subgroup 1 only.
** Subgroups 10 and 11, if not tested shall be guaranteed to the limits specified in Table 1.
---------------------------- Electrical Characteristics of MAX4420 and MAX4429 19-0250 Rev. C
for /883B and SMD 5962-88770 Page 4 of 5
