VOL618A www.vishay.com Vishay Semiconductors Optocoupler, Phototransistor Output, Low Input Current, 4 Pin LSOP, Long Creepage Mini-Flat Package FEATURES * Low profile package A 1 4 C C 2 3 E * High collector emitter voltage, VCEO = 80 V * Isolation test voltage, 5000 VRMS * Isolation voltage VIORM = 1050 Vpeak * Low coupling capacitance * High common mode transient immunity 17295-6 * Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 DESCRIPTION APPLICATIONS The VOL618A has a GaAs infrared emitting diode emitter, which is optically coupled to a silicon planar phototransistor detector, and is incorporated in a 4 pin LSOP wide body package. * Telecom * Industrial controls * Battery powered equipment * Office machines It features a high current transfer ratio, low coupling capacitance, and high isolation voltage. * Programmable controllers The coupling device is designed for signal transmission between two electrically separated circuits. AGENCY APPROVALS * UL1577, file no. E76222 * cUL CSA 22.2 bulletin 5A, double protection * DIN EN 60747-5-5 (VDE 0884-5), available with option 1 * BSI: EN 60065:2002, EN 60950-1:2006 * FIMKO EN60950-1 * CQC: GB8898, GB4943 ORDERING INFORMATION V O L 6 1 8 PART NUMBER A - # X CTR BIN UL, cUL, BSI, FIMKO, CQC UL, cUL, BSI, FIMKO, CQC, VDE (option 1) 4 pin LSOP, mini-flat, long creepage 0 1 PACKAGE OPTION T TAPE AND REEL LSOP 10.2 mm CTR (%) AGENCY CERTIFIED/PACKAGE 4 pin LSOP, mini-flat, long creepage 0 1 mA 63 to 125 100 to 200 160 to 320 VOL618A-2T VOL618A-3T VOL618A-4T 63 to 125 100 to 200 160 to 320 VOL618A-2X001T VOL618A-3X001T VOL618A-4X001T Document Number: 82405 1 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 1.5, 17-Oct-12 VOL618A www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (Tamb = 25 C, unless otherwise specified) PARAMETER INPUT Reverse voltage Power dissipation Forward current Junction temperature OUTPUT Collector emitter voltage Emitter collector voltage TEST CONDITION Collector current SYMBOL VALUE UNIT VR Pdiss IF Tj 6 100 60 125 V mW mA C VCEO VECO IC IC Pdiss Tj 80 7 50 100 150 125 V V mA mA mW C VISO 5000 VRMS Ptot Tstg Tamb Tsld 250 - 55 to + 125 - 55 to + 110 260 mW C C C tp/T = 0.5, tp < 10 ms Power dissipation Junction temperature COUPLER Isolation test voltage between emitter and detector Total power dissipation Storage temperature range Ambient temperature range Soldering temperature (1) 10 s Ptot - Total Power Dissipation (mW) Notes * Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. (1) Refer to reflow profile for soldering conditions for surface mounted devices. 300 Coupled device 250 200 Phototransistor 150 100 IR-diode 50 0 0 20 40 60 80 100 120 Tamb - Ambient Temperature (C) Fig. 1 - Total Power Dissipation vs. Ambient Temperature ELECTRICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) PARAMETER INPUT Forward voltage Capacitance OUTPUT Collector emitter leakage current Collector emitter capacitance COUPLER Collector emitter saturation voltage Coupling capacitance TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT IF = 5 mA VR = 0 V, f = 1 MHz VF CO 1.16 45 1.5 V pF VCE = 10 V, IF = 0 A VCE = 5 V, f = 1 MHz ICEO CCE 10 7 200 nA pF VCEsat VCEsat VCEsat CC 0.25 0.25 0.25 0.25 0.4 0.4 0.4 V V V pF IC = 0.32 mA, IF = 1 mA IC = 0.5 mA, IF = 1 mA IC = 0.8 mA, IF = 1 mA f = 1 MHz VOL618A-2 VOL618A-3 VOL618A-4 Note * Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements. Document Number: 82405 2 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 1.5, 17-Oct-12 VOL618A www.vishay.com Vishay Semiconductors CURRENT TRANSFER RATIO (Tamb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION IC/IF IF = 1 mA, VCE = 5 V PART SYMBOL MIN. MAX. UNIT VOL618A-2 CTR 63 TYP. 125 % VOL618A-3 CTR 100 200 % VOL618A-4 CTR 160 320 % SWITCHING CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) PARAMETER Turn on time Rise time Turn off time Fall time TEST CONDITION SYMBOL VCC = 5 V, IC = 2 mA, RL = 100 VCC = 5 V, IC = 2 mA, RL = 100 VCC = 5 V, IC = 2 mA, RL = 100 VCC = 5 V, IC = 2 mA, RL = 100 ton tr toff tf MIN. TYP. MAX. s s s s VCC = 5 V Input UNIT 6 3.5 5.5 5 Input pulse RL 10 % VOUT Output pulse 90 % tr tf t off t on isfh618a_10 isfh618a_12 Fig. 2 - Test Circuit Fig. 3 - Test Circuit and Waveforms SAFETY AND INSULATION RATED PARAMETERS TEST CONDITION SYMBOL MIN. Partial discharge test voltage routine test PARAMETER 100 %, ttest = 1 s Vpd 2 Partial discharge test voltage lot test (sample test) tTr = 60 s, ttest = 10 s, (see figure 4) VIOTM Insulation voltage Insulation resistance Safety rating - maximum input current Safety rating - maximum power dissipation Rated impulse voltage Safety rating - maximum ambient temperature Vpd TYP. MAX. kVpeak 8 1.68 VIORM UNIT kVpeak kVpeak 1050 Vpeak VIO = 500 V, Tamb = 25 C RIO 1012 VIO = 500 V, Tamb = 100 C RIO 1011 VIO = 500 V, Tamb = 150 C (construction test only) RIO 109 Isi 130 mA PSO 265 mW VIOTM 8 kV Tsi 150 C Clearance distance 8 mm Creepage distance 8 mm 0.4 mm Insulation distance (internal) Note * According to DIN EN 60747-5-5 (VDE 0884), 7.4.3.8.2, (see figure 4). This optocoupler is suitable for safe electrical isolation only within the safety ratings. Compliance with the safety ratings shall be ensured by means of suitable protective circuits. Document Number: 82405 3 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 1.5, 17-Oct-12 VOL618A www.vishay.com Vishay Semiconductors VIOTM 300 t1, t2 t3 , t4 ttest tstres Phototransistor PSO (mW) 250 200 = 1 s to 10 s =1s = 10 s = 12 s Vpd 150 VIOWM VIORM 100 IR-diode Isi (mA) 50 0 0 0 25 50 75 125 100 t3 ttest t4 150 13930 Tsi - Safety Temperature (C) tTr = 60 s t1 t2 t stres t Fig. 4 - Derating Diagram Fig. 5 - Test Pulse Diagram for Sample Test according to DIN EN 60747-5-5 TYPICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) 10 000 IF = 0 mA Tamb = 110 C Tamb = 75 C Tamb = 25 C Tamb = 0 C Tamb = - 55 C 10 ICE0 - Leakage Current (nA) IF - Forward Current (mA) 100 1 0.1 1000 VCE = 40 V 100 10 VCE = 24 V 1 0.1 VCE = 12 V 0.01 0.001 0.6 0.8 1.0 1.2 1.4 1.6 - 60 - 40 - 20 0 VF - Forward Voltage (V) 60 80 100 120 Fig. 8 - Collector Emitter Current vs. Ambient Temperature 35 IF = 25 mA IF = 20 mA 40 IC - Collector Current (mA) IC - Collector Current (mA) 40 Tamb - Ambient Temperature (C) Fig. 6 - Forward Voltage vs. Forward Current 50 20 IF = 15 mA 30 IF = 10 mA 20 10 IF = 5 mA IF = 1 mA 0 IF = 25 mA 30 25 20 IF = 1 mA IF = 10 mA IF = 0.5 mA IF = 5 mA 15 10 5 IF = 2 mA 0 0 1 2 3 4 5 6 7 8 9 10 VCE - Collector Emitter Voltage (non-sat) (V) Fig. 7 - Collector Current vs. Collector Emitter Voltage (non-saturated) 0.0 0.1 0.2 0.3 0.4 VCE - Collector Emitter Voltage (V) Fig. 9 - Collector Current vs. Collector Emitter Voltage (saturated) Document Number: 82405 4 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 1.5, 17-Oct-12 VOL618A www.vishay.com Vishay Semiconductors 2.0 NCTR - Normalized CTR (sat) NCTR - Normalized CTR (sat) 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 Normalized to CTR value: IF = 5 mA, VCE = 5 V, Tamb = 25 C - 60 - 40 - 20 0 20 40 60 Tamb = 0 C 1.8 1.6 Tamb = - 55 C 1.4 1.2 1.0 0.8 0.6 Tamb = 25 C 0.4 0.2 Tamb = 110 C 0.0 80 100 120 0.1 100 Fig. 13 - Current Transfer Ratio vs. Forward Current (non-saturated) Normalized to 1 mA at 25 C 1.4 0 1.2 - 20 Phase Angle (deg) NCTR - Normalized CTR (non-saturated) Fig. 10 - Normalized Current Transfer Ratio vs. Ambient Temperature (saturated) 1.0 0.8 0.6 0.4 Normalized to CTR value: IF = 5 mA, VCE = 5 V, Tamb = 25 C VCE = 5 V RL = 100 - 40 - 60 - 80 RL = 1000 - 100 - 120 - 140 0 - 160 - 60 - 40 - 20 0 20 40 60 80 100 120 1 Tamb - Ambient Temperature (C) 10 100 1000 f - Cut-off Frequency (kHz) Fig. 14 - fCTR vs. Phase Angle Fig. 11 - Normalized Current Transfer Ratio vs. Ambient Temperature (non-saturated) 1000 2.5 Tamb = 0 C VCC = 5 V Tamb = - 55 C 2.0 1.5 f CTR (kHz) NCTR - Normalized CTR (NS) 10 IF - Forward Current (mA) Tamb - Ambient Temperature (C) 0.2 1 Tamb = 25 C 1.0 100 10 Tamb = 110 C 0.5 0.0 1 0.1 1 10 100 IF - Forward Current (mA) Fig. 12 - Current Transfer Ratio vs. Forward Current (saturated) Normalized to 1 mA at 25 C 0.1 1 10 100 IC (mA) Fig. 15 - Cut-off Frequency (- 3 dB) vs. Collector Current Document Number: 82405 5 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 1.5, 17-Oct-12 VOL618A www.vishay.com ton, toff Switching Time (s) 1000 VCE = 5 V, Ic = 2 mA toff (s) 100 10 ton (s) 1 0.1 0 5 10 15 20 ton/toff - Turn-On/Turn-Off Time (s) Vishay Semiconductors 50 Saturated operation VS = 5 V RL = 1 k 40 30 toff 20 10 ton 0 0 RL - Load Resistance (k) Fig. 16 - Switching Time vs. Load Resistance 10 15 20 Fig. 18 - Turn-On/Turn-Off Time vs. Forward Current 0 1.0 RL = 100 -5 20 % used 0.8 - 10 CTR = 50 % used Voltage Gain VCEsat - Collector Emitter Saturation Voltage (V) 5 IF - Forward Current (mA) 95 11031 0.6 0.4 - 15 - 20 RL = 1000 - 25 - 30 0.2 - 35 10 % used 0 VCE = 5 V - 40 1 95 11028 10 100 IC - Collector Current (mA) Fig. 17 - Collector Emitter Saturation Voltage vs. Collector Current 1 10 100 1000 f - Cut-off Frequency (kHz) Fig. 19 - Voltage Gain vs. Cut-off Frequency Document Number: 82405 6 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 1.5, 17-Oct-12 VOL618A www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 2.30 max. 4.10 max. 10.20 3.80 + 0.30 - 0.40 0.20 2.00 0.10 0.10 + 0.10 - 0.05 7.50 0.20 0.45 0.1 0.70 + 0.30 - 0.40 2.54 nom. 4 3 2.54 Possible footprint 0.90 8.20 1 22533 10.80 technical drawings according to DIN specifications 2 Pin no. 1 identification PACKAGE MARKING (example of VOL618A-3X001T) 618A-3X1 V YWW 68 Notes * Only option 1 is reflected in the package marking with the characters "X1". * Tape and reel suffix (T) is not part of the package marking. TAPE AND REEL DIMENSIONS in millimeters O 1.55 2.7 4 2 0.3 7.5 Tape slot in core 1.75 ESD sticker 10.6 16 330 (13") 5 4.25 8 O 1.6 Regular, special or bar code label 17999 Fig. 20 - Reel Dimensions (3000 units per reel) 2.3 Direction of pulling out technical drawings according to DIN specification 22662 Fig. 21 - Tape Dimensions Document Number: 82405 7 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 1.5, 17-Oct-12 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000