Semiconductor This version: Jun. 2000 MSM5117400D 4,194,304-Word x 4-Bit DYNAMIC RAM : FAST PAGE MODE TYPE DESCRIPTION The MSM5117400D is a 4,194,304-word x 4-bit dynamic RAM fabricated in Oki's silicon-gate CMOS technology. The MSM5117400D achieves high integration, high-speed operation, and low-power consumption because Oki manufactures the device in a quadruple-layer polysilicon/double-layer metal CMOS process. The MSM5117400D is available in a 26/24-pin plastic SOJ, 26/24-pin plastic TSOP. FEATURES * 4,194,304-word x 4-bit configuration * Single 5V power supply, 10% tolerance * Input : TTL compatible, low input capacitance * Output : TTL compatible, 3-state * Refresh : 2048 cycles/32 ms * Fast page mode, read modify write capability * CAS before RAS refresh, hidden refresh, RAS-only refresh capability * Multi-bit test mode capability * Package options: 26/24-pin 300mil plastic SOJ (SOJ26/24-P-300-1.27) (Product : MSM5117400D-xxSJ) 26/24-pin 300mil plastic TSOP (TSOPII26/24-P-300-1.27-K) (Product : MSM5117400D-xxTS-K) xx : indicates speed rank. PRODUCT FAMILY Family Access Time (Max.) Cycle Time Power Dissipation tRAC tAA tCAC tOEA (Min.) Operating (Max.) MSM5117400D-50 50ns 25ns 13ns 13ns 90ns 550mW MSM5117400D-60 60ns 30ns 15ns 15ns 110ns 495mW MSM5117400D-70 70ns 35ns 20ns 20ns 130ns 440mW Standby (Max.) 5.5mW 1/14 MSM5117400D PIN CONFIGRATION (TOP VIEW) VCC DQ1 DQ2 WE RAS NC OE A9 VCC DQ1 DQ2 WE RAS NC 1 2 3 4 5 6 26 25 24 23 22 21 VSS DQ4 DQ3 CAS OE A9 A8 A7 A6 A5 A4 VSS A10 8 A0 9 A1 10 A2 11 A3 12 VCC 13 19 18 17 16 15 14 A8 A7 A6 A5 A4 VSS 1 2 3 4 5 6 26 25 24 23 22 21 VSS DQ4 DQ3 CAS A10 8 A0 9 A1 10 A2 11 A3 12 VCC 13 19 18 17 16 15 14 26/24-Pin Plastic SOJ 26/24-Pin Plastic TSOP (K Type) Pin Name Function A0-A10 Address Input RAS Row Address Strobe CAS Column Address Strobe DQ1-DQ4 Data Input/Data Output OE Output Enable WE Write Enable VCC Power Supply (5V) VSS Ground (0V) NC No Connection 2/14 MSM5117400D BLOCK DIAGRAM Timing Generator RAS Timing Generator CAS 11 Column Address Buffers 11 Internal Address Counter A0 - A10 11 Row Address Buffers Refresh Control Clock 11 Row Decoders Word Drivers Column Decoders Sense Amplifiers WE Write Clock Generator 4 I/O Selector OE 4 Output Buffers 4 Input Buffers 4 4 4 DQ1 - DQ4 4 Memory Cells VCC On Chip VBB Generator VSS 3/14 MSM5117400D ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings Parameter Symbol Rating Unit Voltage on Any Pin Relative to VSS VIN, VOUT -0.5 to VCC + 0.5 V Voltage VCC supply Relative to VSS VCC 0.5 to 7.0 V Short Circuit Output Current IOS 50 mA Power Dissipation PD* 1 W Operating Temperature Topr 0 to 70 C Storage Temperature Tstg -55 to 150 C *: Ta = 25C Recommended Operating Conditions (Ta = 0C to 70C) Parameter Power Supply Voltage Input High Voltage Input Low Voltage Notes: Symbol Min. Typ. Max. Unit VCC VSS VIH VIL 4.5 5.0 5.5 V 0 0 0 V 2.4 VCC + 0.5*1 V -0.5 0.8 V *2 *1. The input voltage is VCC + 2.0V when the pulse width is less than 20ns (the pulse width is with respect to the point at which VCC is applied). *2. The input voltage is VSS - 2.0V when the pulse width is less than 20ns (the pulse width respect to the point at which VSS is applied). Capacitance (VCC = 5V 10%, Ta = 25C, f=1MHz) Parameter Input Capacitance (A0 - A10) Input Capacitance (RAS, CAS, WE, OE) Output Capacitance (DQ1 - DQ4) Symbol Typ. Max. Unit CIN1 5 pF CIN2 7 pF CI/O 7 pF 4/14 MSM5117400D DC Characteristics (VCC = 5V 10%, Ta = 0C to 70C) Parameter Symbol Condition Max Min. Max Min. Max 2.4 VCC 2.4 VCC 2.4 VCC V 0 0.4 0 0.4 0 0.4 V -10 10 -10 10 -10 10 A -10 10 -10 10 -10 10 A 100 90 80 mA 1,2 RAS, CAS = VIH 2 2 2 RAS, CAS VCC - 0.2V 1 1 1 mA 1 100 90 80 mA 1,2 5 5 5 mA 1 100 90 80 mA 1,2 80 70 60 mA 1,3 VOH IOH = -5.0mA Output Low Voltage VOL IOL = 4.2mA 0V VI 6.5V ; Input Leakage Current ILI Output Leakage Current ILO Average Power Supply Current ICC1 (Operating) ICC2 (Standby) Average Power Supply Current All other pins not under test = 0V DQ disable 0V VO VCC RAS, CAS cycling, tRC = Min. RAS cycling, ICC3 CAS = VIH, (RAS-only Refresh) tRC = Min. Power Supply Current RAS = VIH, ICC5 (Standby) CAS = VIL, DQ = enable Average Power Supply Current (CAS before RAS Refresh) Average Power Supply Current (Fast Page Mode) Notes: 1. Note Min. Output High Voltage Power Supply Current MSM5117400 MSM5117400 MSM5117400 D-50 D-60 D-70 Unit ICC6 RAS = cycling, CAS before RAS RAS = VIL, ICC7 CAS cycling, tPC = Min. ICC Max. is specified as ICC for output open condition. 2. The address can be changed once or less while RAS = VIL. 3. The address can be changed once or less while CAS = VIH. 5/14 MSM5117400D AC Characteristic (1/2) (VCC = 5V 10%, Ta = 0C to 70C) Note1,2,3 Parameter MSM5117400 D-50 Symbol MSM5117400 D-60 MSM5117400 D-70 Unit Note Min. Max. Min. Max. Min. Max. tRC 90 110 130 ns tRWC 131 155 185 ns tPC 35 40 45 ns tPRWC 76 85 100 ns Access Time from RAS tRAC 50 60 70 ns 4,5,6 Access Time from CAS tCAC 13 15 20 ns 4,5 Access Time from Column Address tAA 25 30 35 ns 4,6 Access Time from CAS Precharge tCPA 30 35 40 ns 4 Access Time from OE tOEA 13 15 20 ns 4 Output Low Impedance Time from CAS tCLZ 0 0 0 ns 4 CAS to Data Output Buffer Turnoff Delay Time tOFF 0 13 0 15 0 20 ns 7 OE to Data Output Buffer Turn-off Delay Time tOEZ 0 13 0 15 0 20 ns 7 Transition Time tT 3 50 3 50 3 50 ns 3 Refresh Period tREF 32 32 32 m RAS Precharge Time tRP 30 40 50 ns RAS Pulse Width tRAS 50 10,000 60 10,000 70 10,000 ns RAS Pulse Width (Fast Page Mode) tRASP 50 100,000 60 100,000 70 100,000 ns RAS Hold Time tRSH 13 15 20 ns RAS Hold Time referenced to OE tROH 13 15 20 ns CAS Precharge Time (Fast Page Mode) tCP 7 10 10 ns CAS Pulse Width tCAS 13 10,000 15 10,000 20 10,000 ns CAS Hold Time tCSH 50 60 70 ns CAS to RAS Precharge Time tCRP 5 5 5 ns RAS Hold Time from CAS Precharge tRHCP 30 35 40 ns RAS to CAS Delay Time tRCD 17 37 20 45 20 50 ns RAS to Column Address Delay Time tRAD 12 25 15 30 15 35 ns Row Address Set-up Time tASR 0 0 0 ns Row Address Hold Time tRAH 7 10 10 ns Column Address Set-up Time tASC 0 0 0 ns Random Read or Write Cycle Time Read Modify Write Cycle Time Fast Page Mode Cycle Time Fast Page Mode Read Modify Write Cycle Time 5 6/14 MSM5117400D AC Characteristic (2/2) (VCC = 5V 10%, Ta = 0C to 70C) Note1,2,3 Parameter Symbol MSM5117400 D-50 MSM5117400 D-60 MSM5117400 D-70 Min. Max. Min. Max. Min. Max. Unit Note Column Address Hold Time tCAH 7 10 15 ns Column Address to RAS Lead Time tRAL 25 30 35 ns Read Command Set-up Time tRCS 0 0 0 ns Read Command Hold Time tRCH 0 0 0 ns 8 Read Command Hold Time referenced to RAS tRRH 0 0 0 ns 8 Write Command Set-up Time tWCS 0 0 0 ns 9 Write Command Hold Time tWCH 7 10 15 ns Write Command Pulse Width tWP 7 10 10 ns OE Command Hold Time tOEH 13 15 20 ns Write Command to RAS Lead Time tRWL 13 15 20 ns Write Command to CAS Lead Time tCWL 13 15 20 ns Data-in Set-up Time tDS 0 0 0 ns 10 Data-in Hold Time tDH 7 10 15 ns 10 OE to Data-in Delay Time tOED 13 15 20 ns CAS to WE Delay Time tCWD 36 40 50 ns 9 Column Address to WE Delay Time tAWD 48 55 65 ns 9 RAS to WE Delay Time tRWD 73 85 100 ns 9 CAS Precharge WE Delay Time tCPWD 53 60 70 ns 9 CAS Active Delay Time from RAS Precharge tRPC 5 5 5 ns RAS to CAS Set-up Time (CAS before RAS) tCSR 10 10 10 ns RAS to CAS Hold Time (CAS before RAS) tCHR 10 10 10 ns WE to RAS Precharge Time (CAS before RAS) tWRP 10 10 10 ns WE Hold Time from RAS (CAS before RAS) tWRH 10 10 10 ns RAS to WE Set-up Time (Test Mode) tWTS 10 10 10 ns RAS to WE Hold Time (Test Mode) tWTH 10 10 10 ns 7/14 MSM5117400D Notes: 1. A start-up delay of 200s is required after power-up, followed by a minimum of eight initialization cycles (RAS-only refresh or CAS before RAS refresh) before proper device operation is achieved. 2. The AC characteristics assume tT = 5ns. 3. VIH (Min.) and VIL (Max.) are reference levels for measuring input timing signals. Transition times (tT) are measured between VIH and VIL. 4. This parameter is measured with a load circuit equivalent to 2 TTL load and 100pF. 5. Operation within the tRCD (Max.) limit ensures that tRAC (Max.) can be met. tRCD (Max.) is specified as a reference point only. If tRCD is greater than the specified tRCD (Max.) limit, then the access time is controlled by tCAC. 6. Operation within the tRAD (Max.) limit ensures that tRAC (Max.) can be met. tRAD (Max.) is specified as a reference point only. If tRAD is greater than the specified tRAD (Max.) limit, then the access time is controlled by tAA. 7. tOFF (Max.) and tOEZ (Max.) define the time at which the output achieved the open circuit condition and are not referenced to output voltage levels. 8. tRCH or tRRH must be satisfied for a read cycle. 9. tWCS, tCWD, tRWD, tAWD and tCPWD are not restrictive operating parameters. They are included in the data sheet as electrical characteristics only. If tWCS tWCS (Min.), then the cycle is an early write cycle and the data out will remain open circuit (high impedance) throughout the entire cycle. If tCWD tCWD (Min.), tRWD tRWD(Min.), tAWD tAWD (Min.) and tCPWD tCPWD (Min.), then the cycle is a read modify write cycle and data out will contain data read from the selected cell; if neither of the above sets of conditions is satisfied, then the condition of the data out (at access time) is indeterminate. 10. These parameters are referenced to the CAS leading edge in an early write cycle, and to the WE leading edge in an OE control write cycle, or a read modify write cycle. 11. The test mode is initiated by performing a WE and CAS before RAS refresh cycle. This mode is latched and remains in effect until the exit cycle is generated. In a test mode CA0 and CA1 are not used and each DQ pin now accesses 4-bit locations. Since all 4DQ pins are used, a total of 16 data bits can be written in parallel into the memory array. In a read cycle, if 4 data bits are equal, the DQ pin will indicate a high level. If the 4 data bits are not equal, the DQ pin will indicate a low level. The test mode is cleared and the memory device returned to its normal operating state by performing a RAS-only refresh cycle or a CAS before RAS refresh cycle. 12. In a test mode read cycle, the value of access time parameters is delayed for 5ns for the specified value. These parameters should be specified in test mode cycle by adding the above value to the specified value in this data sheet. 8/14 MSM5117400D Timing Chart * Read Cycle RAS tRC tRAS VIH tRP VIL tCSH tCRP CAS tRAD VIL WE OE VIH VIL tCRP tRSH tCAS VIH tRAL tASR Address tRCD tRAH tASC Row tCAH Column tRCS tRRH VIH tAA VIL tRCH tROH tOEA VIH VIL tCAC tOFF tRAC DQ tOEZ tCLZ VOH Valid Data-out Open VOL "H" or "L" * Write Cycle (Early Write) RAS tRC tRAS VIH tRP VIL tCSH tCRP CAS tRCD VIH tRAD VIL tRAL tASR Address WE OE DQ VIH VIL VIH tCRP tRSH tCAS tRAH tASC Row tCAH Column tCWL tWCS tWP tWCH VIL tRWL VIH VIL VIH VIL tDS tDH Valid Data-in Open "H" or "L" 9/14 MSM5117400D * Read Modify Write Cycle tRWC RAS tRAS VIH tRP VIL tCSH tCRP CAS tRSH tCAS VIH VIH VIL tCRP tRAD VIL tASR Address tRCD tRAH Row tASC tCWL tRWL tCAH Column tRCS tCWD tRWD WE OE tWP VIH VIL tAWD tAA tOEH tOEA VIH tOED VIL tCAC tDH tRAC DQ VI/OH VI/OL tOEZ tCLZ Valid Data-out tDS Valid Data-in "H" or "L" 10/14 MSM5117400D * Fast Page Mode Cycle tRASP RAS VIH VIL tRCD tCRP CAS tCP VIH VIL VIH VIL tRAD tCSH tRAH tASC tCP Row tASC Column tCAH Column tRCS tRCH tRCS tRCH VIH VIL tAA tAA VIH VIL tRAC tCPA tOFF tOEZ tCLZ VOH tAA tOEA tCAC DQ tASC Column tRCH tCRP tRAL tCAH tOEA OE tRSH tCAS tCAS tCAH tRCS WE tRHCP tCAS tASR Address tRP tPC tCPA tOFF tCAC tOEZ tCLZ Valid Data-out VOL tRRH tOEA tOFF tCAC tOEZ tCLZ Valid Data-out Valid Data-out "H" or "L" * Fast Page Mode Write Cycle (Early Write) tRP tRASP RAS CAS tPC VIH VIL tCRP VIL tRAH tASC Row tCSH tCAH tASC Column tCRP tCAS VIH tCAH tASC Column tCWL tWCH tWP Column tCWL tWCS tRAL tCAH tWCH tWP tCWL tRWL tWCS tWP tWCH VIL tDS DQ tCAS tRSH tRAD VIL VIH tCP tCAS tWCS WE tCP VIH tASR Address tRCD tRHPC VIH VIL tDH Valid Data-in tDS tDH Valid Data-in tDS tDH Valid Data-in Note: OE = "H" or "L" "H" or "L" 11/14 MSM5117400D * Fast Page Mode Read Modify Write Cycle tRASP RAS CAS tCSH VIH VIL tRCD VIL tCAH tCWL tASC Row tASC tRAL tCWL Column tCWD tRCS tCPWD tCWD tAWD tAWD tRCS tRWD tCWD tCPWD tCWL tRWL VIH tAWD VIL tWP tCPA tDH VIH tWP tDH tCAC VI/OH tOEZ Out VI/OL tCLZ tCPA tAA In tOEA tOED tOEZ tCAC tDH tDS tOEA tOED VIL tWP tROH tDS tAA tDS tOEA Out tOED tOEZ tCAC In Out In tCLZ tCLZ Note: In = Valid Data-in, Out = Valid Data-out * tCRP tCAH Column tAA DQ tCAS tASC Column tRAC OE tCP tCAS tRAD VIL VIH tRP tRSH tCAH tRCS WE tCP tCAS VIH tRAH tASR Address tPRWC "H" or "L" RAS-only Refresh Cycle tRC RAS tRAS VIH tRP VIL tCRP CAS Address DQ tRPC VIH VIL VIH VIL VOH VOL tASR tRAH Row tOFF Open Note: WE, OE = "H" or "L" "H" or "L" 12/14 MSM5117400D * CAS before RAS Refresh Cycle tRP RAS CAS WE DQ tRC tRAS VIH VIL tRPC tCP tRP tCSR tRPC tCHR VIH VIL tWRP tWRH tWRP VIH VIL tOFF VOH Open VOL Note: WE, OE, Address = "H" or "L" * "H" or "L" Hidden Refresh Read Cycle tRC RAS CAS VIH VIL tCRP tRCD tRSH VIH tRAD VIL VIH VIL tRAH tASC tCAH Column Row tRCS WE tRP tRP tCHR tASR Address tRC tRAS tRAS tCAC tRRH VIH tRAL VIL tAA tROH OE DQ VIH VIL VOH VOL tOFF tOEA tRAC tOEZ tCLZ Open Valid Data-out "H" or "L" 13/14 MSM5117400D * Hidden Refresh Write Cycle tRC RAS CAS VIH VIL tCRP tRCD tRSH OE DQ tRP VIH tRAD VIL VIH VIL tRAL tRAH tASC Row tCAH Column tWCS WE tRP tCHR tASR Address tRC tRAS tRAS tWCH VIH VIL tWRH tWRP tWP VIH VIL tDS VIH tDH Valid Data-in VIL "H" or "L" * Test Mode Initiate Cycle tRC tRP RAS CAS tRAS VIH VIL tRPC tCP VIH tCSR VIL tWTS WE DQ tCHR VIH VIL VIH VIL tWTH tOFF Open Note: OE, Address = "H" or "L" "H" or "L" 14/14