MANUFACTURER CATEGORY
SERIES
PACKAGE
VOLTAGE
CLASS REV.DATE
ECLIPTEK CORP. OSCILLATOR EPSA23 CERAMIC 3.3V OS8G 10/11
EPSA23 Series
OSCILLATOR
EPSA23
ELECTRICAL SPECIFICATIONS
800-ECLIPTEK www.ecliptek.com for latest revision Specifications subject to change without notice.
• Programmable Spread Spectrum Oscillators
• Low EMI
LVCMOS Output
• +3.3V Supply Voltage
• Tri-State and Power Down Options
• Center Spread and Down Spread Modulation Options
• 4 Pad Ceramic SMD Package
• RoHS Compliant (Pb-Free)
H 1.3
L 5.0
W 3.2
2.000MHz to 200.000MHz
-40°C to +85°C
-55°C to +125°C
3.3VDC ±10%
-0.5VDC to 4.2VDC
15mA Maximum
23mA Maximum
27mA Maximum
30mA Maximum
40mA Maximum
±50ppm Maximum
90% of VDD Minimum
10% of VDD Maximum
3nSeconds Maximum
50 ±5(%)
15pF Maximum
CMOS
Tri-State or Power Down
Enables Output
Enables Output
Disables Output: High Impedance
100nSec Maximum
3mSec Maximum
10µA Maximum
100nSec Maximum
100nSec Maximum
20mA Maximum
Center Spread
Down Spread
30kHz Minimum, 32kHz Typical, 45kHz
Maximum
100pSec Maximum
10mSec Maximum
Nominal Frequency
Some frequencies within this range may
not be available
Operating Temperature Range
Storage Temperature Range
Supply Voltage (VDD)
Maximum Supply Voltage
Input Current
Frequency Tolerance / Stability
Output Voltage Logic High (VOH)
Output Voltage Logic Low (VOL)
Rise Time / Fall Time
Duty Cycle
Load Drive Capability
Output Logic Type
Output Control Function
Tri-State/Power Down Input Voltage
Power Down Output Disable Time
Power Down Output Enable Time
Standby Current
Tri-State Output Disable Time
Tri-State Output Enable Time
Disable Current
Spread Spectrum Percentage
Some options may not be available
Modulation Frequency
Period Jitter
Start Up Time
2.000MHz to 25.000MHz
25.001MHz to 50.000MHz
50.001MHz to 100.000MHz
100.001MHz to 166.000MHz
166.001MHz to 200.000MHz
Inclusive of All Conditions: Frequency Stability over the
Operating Temperature Range, Supply Voltage Change,
Output Load Change, 1st Year Aging at 25°C, Shock, and
Vibration
IOH = -8mA
IOL = +8mA
10% to 90% of waveform
at 50% of waveform
High Impedance Internal Pull Down Resistor of
100kOhms Typical on Pad 1
VIH of 70% of VDD Minimum
No Connection
VIL of 30% of VDD Maximum
Unloaded; Pad 1 = Ground
Unloaded; Pad 1 = Ground
±0.25%, ±0.50%, ±0.75%, ±1.0%, ±1.5%, ±2.0%
-0.50%, -1.0%, -1.5%, -2.0%, -3.0%, -4.0%
Cycle to Cycle; Spread Spectrum-On
MANUFACTURER CATEGORY
SERIES
PACKAGE
VOLTAGE
CLASS REV.DATE
ECLIPTEK CORP. OSCILLATOR EPSA23 CERAMIC 3.3V OS8G 10/11
MECHANICAL DIMENSIONS
ALL DIMENSIONS IN MILLIMETERS
ENVIRONMENTAL/MECHANICAL SPECIFICATIONS MARKING SPECIFICATIONS
TAPE AND REEL DIMENSIONS
ALL DIMENSIONS IN MILLIMETERS
SUGGESTED SOLDER PAD LAYOUT
ALL DIMENSIONS IN MILLIMETERS
800-ECLIPTEK www.ecliptek.com for latest revision Specifications subject to change without notice.
EPSA23 B B H A - 44.736M TR
PART NUMBERING GUIDE
AVAILABLE OPTIONS
Blank=Bulk
TR=Tape and Reel
FREQUENCY
SPREAD SPECTRUM PERCENTAGE
A = ±0.25% Center Spread G = -0.50% Down Spread
B = ±0.50% Center Spread H = -1.00% Down Spread
C = ±0.75% Center Spread J = -1.50% Down Spread
D = ±1.00% Center Spread L = -2.00% Down Spread
E = ±1.50% Center Spread N = -3.00% Down Spread
F = ±2.00% Center Spread P = -4.00% Down Spread
FREQUENCY TOLERANCE & STABILITY
B=±50ppm Maximum
OPERATING TEMPERATURE RANGE
B=-40°C to +85°C
OUTPUT CONTROL FUNCTION
H=Tri-State
J=Power Down
Tolerances= +0.1
Pin 1: Tri-State or Power Down
Pin 2: Case Ground
Pin 3: Output
Pin 4: Supply Voltage
Characteristic Specification
ESD Susceptibility MIL-STD-883, Method 3015, Class 1, HBM: 1500V
Fine Leak Test MIL-STD-883, Method 1014, Condition A
Flammability UL94-V0
Gross Leak test MIL-STD-883, Method 1014, Condition C
Mechanical Shock MIL-STD-883, Method 2002, Condition B
Moisture Resistance MIL-STD-883, Method 1004
Moisture Sensitivity J-STD-020, MSL 1
Resistance to Soldering Heat MIL-STD-202, Method 210, Condition K
Resistance to Solvents MIL-STD-202, Method 215
Solderability MIL-STD-883, Method 2003
Temperature Cycling MIL-STD-883, Method 1010, Condition B
Vibration MIL-STD-883, Method 2007, Condition A
3.20
±0.20
5.00
±0.20 2.54
±0.15
1.3
MAX
1.00 ±0.20 (x4)
2.20
±0.15
1.20 ±0.20
1.20
±0.20
(x4)
4
3
1
2
N
O
P
Q
S Width
T Depth
(Tape Slot in Core
for Tape Start)
R
(Access Hole
at Slot Location)
U
W
V
N O P Q R
1.5 MIN 50 MIN 20.2 MIN 13.0 ±0.2 40 MIN
S T U V W
QTY/REEL
2.5 MIN 10 MIN 22.4 MAX 180 MAX 16.4 +2.0/-0.0 1,000
REEL
TAPE
A B C D E F
16.0 ±0.3 7.5 ±0.1 1.50 MIN 4.0 ±0.1 2.0 ±0.1 8.0 ±0.1
G H I J K L M
A0 1.5 +0.1/-0.0 1.75 ±0.10 B0 0.60 MAX 0.10 MAX K0
Note: Compliant to EIA-481
D
E
FG
HK
L
I
M
J
C
A
Direction of Unreeling
B
MARKING
ORIENTATION
Line 1: E XX.XXX
Frequency in MHz (5 Digits Maximum + Decimal)
Ecliptek Designator
Line 2: S XXXXX
Ecliptek Manufacturing Identifier
Configuration Designator
