Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
200990B • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • April 1, 2009 1
DATA SHEET
SKY73085-11: 390 – 500 MHz High Gain and Linearity
Diversity Downconversion Mixer for 2G/3G Base Station
Transceiver Applications
Applications
• 2G/3G base station transceivers:
− GSM/EDGE, CDMA, UMTS/WCDMA
• Land mobile radio
• ISM band transceivers
• High performance radio links
• RF identification
Features
• Operating frequency range: 390 to 500 MHz
• IF frequency range: 50 to 250 MHz
• Conversion gain: 9.3 dB
• Input IP3: 24.9 dBm
• Output IP3: 34.2 dBm
• Noise figure: 9.3 dB
• Integrated LO drivers
• Integrated low loss RF baluns
• High linearity IF amplifiers
• On-chip SPDT LO switch (greater than 60 dB LO-to-LO isolation)
• Small, MCM (36-pin, 6 x 6 mm) Pb-free package (MSL3, 260 °C
per JEDEC J-STD-020)
Description
The SKY73085-11 is a fully integrated diversity mixer that
includes Local Oscillator (LO) drivers, an LO switch, high linearity
mixers, and large dynamic range Intermediate Frequency (IF)
amplifiers. Low loss RF baluns have also been included to reduce
design complications and lower system cost.
The SKY73085-11 features an input IP3 of 24.9 dBm and a Noise
Figure (NF) of 9.3 dB, making the device an ideal solution for high
dynamic range systems such as 2G/3G base station receivers.
The LO switch provides more than 60 dB of isolation between LO
inputs and supports the switching time required for GSM/EDGE
base stations.
The SKY73085-11 is manufactured using a robust silicon BiCMOS
process and has been designed for optimum long-term reliability.
The SKY73085-11 diversity downconversion mixer is provided in
a compact, 36-pin Multi-Chip Module (MCM). A functional block
diagram is shown in Figure 1. The pin configuration and package
are shown in Figure 2. Signal pin assignments and functional pin
descriptions are provided in Table 1.
S643
RFA
RFB
IFB+ IFB–
LO1
LO2
LO_SEL
(Switch Enable)
IFA+ IFA–
Figure 1. SKY73085-11 Block Diagram
DATA SHEET • SKY73085-11 DOWNCONVERSION MIXER
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
2 April 1, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200990B
S646
27
26
25
24
23
22
21
20
19
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 1617 18
3635 34 33 32 31 30 2928
NC
RFA
V
CC_LO
GND
V
CC_LO
GND
NC
RFB
V
CC_RFB
NC
GND
IFB+
IFB–
NC
VCC_IFB
RIFB
NC
VCC_RFA
NC
GND
IFA–
IFA+
NC
VCC_IFA
RIFA
NC
GND
GND
LO2
GND
GND
GND
LO_SEL
GND
LO1
VCC_LO
Figure 2. SKY73085-11 Pinout – 36-Pin MCM
(Top View)
Table 1. SKY73085-11 Signal Descriptions
Pin # Name Description Pin # Name Description
1 RFA RF channel A input 19 LO1 Local oscillator #1 input
2 NC No connect 20 GND Ground
3 GND Ground 21 VCC5 DC supply, +5 V
4 VCC1 DC supply, +5 V 22 GND Ground
5 GND Ground 23 LO_SEL Local oscillator switch select
6 VCC2 DC supply, +5 V 24 GND Ground
7 GND Ground 25 GND Ground
8 NC No connect 26 GND Ground
9 RFB RF channel B input 27 LO2 Local oscillator #2 input
10 VCC3 DC supply, +5 V 28 NC No connect
11 NC No connect 29 RIFA IF channel A bias control
12 GND Ground 30 VCC6 DC supply, +5 V
13 IFB+ IF channel B positive output 31 NC No connect
14 IFB– IF channel B negative output 32 IFA+ IF channel A positive output
15 NC No connect 33 IFA– IF channel A negative output
16 VCC4 DC supply, +5 V 34 GND Ground
17 RIFB IF channel B bias control 35 NC No connect
18 NC No connect 36 VCC7 DC supply, +5 V
DATA SHEET • SKY73085-11 DOWNCONVERSION MIXER
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
200990B • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • April 1, 2009 3
Functional Description
The SKY73085-11 is a high gain diversity mixer, optimized for
base station receiver applications. The device consists of two
diversity channels, each consisting of a low loss RF balun, high
linearity passive mixer, and a low noise IF amplifier.
LO amplifiers are also included that allow the SKY73085-11 to
connect directly to the output of a Voltage Controlled Oscillator
(VCO). This eliminates the extra gain stages needed by most
discrete passive mixers. A Single Pole, Double Throw (SPDT)
switch has been included to select between two different LO
inputs for frequency hopping applications (i.e., GSM).
RF Baluns and Passive Mixer
The RF baluns provide a single ended input, which can easily be
matched to 50 Ω using a simple matching circuit. The RF
baluns offer very low loss and excellent amplitude and phase
balance.
The high linearity mixer is a passive, double balanced mixer that
provides a very low insertion loss, and excellent 3rd Order Input
Insertion Point (IIP3) and linearity performance.
Additionally, the balanced nature of the mixer provides for
excellent port-to-port isolation.
LO Buffers and SPDT LO Switch
The LO buffers allow the input power of the SKY73085-11 to be
programmed in the range of –6 to +6 dBm. The LO section has
been optimized for high-side LO injection. However, the LO can
be driven over a wide frequency range with only slight
degradation in performance.
A high isolation SPDT switch allows the SKY73085-11 to be
used for frequency hopping applications. This switch provides
greater than 60 dB of LO1 to LO2 isolation:
LO_SEL Logic: LO Path Enabled:
High Pin 19 (LO1)
Low (default) Pin 27 (LO2)
For applications that do not require frequency hopping, LO_SEL
is fixed to one state and the appropriate LO input is used. An
internal pull-down resistor on pin 23 (LO_SEL) sets the default
LO path to LO2.
IF Amplifier
The SKY73085-11 includes high dynamic range IF amplifiers
that follow the passive mixers in the signal path. The outputs
require a supply voltage connection using inductive chokes.
These choke inductors should be high-Q and have the ability to
handle 200 mA or greater.
A simple matching network allows the output ports to be
matched to a balanced 200 Ω impedance. The IF amplifiers are
optimized for IF frequencies between 40 and 250 MHz. The IF
amplifiers can be operated outside of this range, but with a
slight degradation in performance.
Electrical and Mechanical Specifications
The absolute maximum ratings of the SKY73085-11 are
provided in Table 2. The recommended operating conditions are
specified in Table 3 and electrical specifications are provided in
Table 4.
Typical performance characteristics of the SKY73085-11 are
illustrated in Figures 3 through 28.
Table 2. SKY73085-11 Absolute Maximum Ratings
Parameter Symbol Minimum Typical Maximum Units
Supply voltage, +5 V (VCC1 – VCC7) VCC 4.5 5.0 5.5 V
Supply current ICC 350 420 mA
RF input power PRF 20 dBm
LO input power PLO 0 20 dBm
Operating case temperature TC –40 +85 °C
Junction temperature TJ +150 °C
Storage case temperature TSTG –40 +125 °C
Note: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other
parameters set at or below their nominal value.
Nominal thermal resistance (junction to center ground pad) is 5.1 °C/W.
DATA SHEET • SKY73085-11 DOWNCONVERSION MIXER
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
4 April 1, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200990B
Table 3. SKY73085-11 Recommended Operating Conditions
Parameter Symbol Minimum Typical Maximum Units
Supply voltage, +5 V (VCC1 – VCC7) VCC 4.75 5.00 5.25 V
Supply current ICC 350 mA
LO input power PLO –6 0 +6 dBm
LO select logic:
high
low
LO_SELH
LO_SELL
2.2
0.8
V
V
Operating case temperature TC –40 +85 °C
Table 4. SKY73085-11 Electrical Specifications (1 of 2)
(Voltage Supply = +5 V, TC = +25 °C, LO = 0 dBm, RF Frequency = 450 MHz, IF Frequency = 90 MHz, LO Frequency = 540 MHz, Unless
Otherwise Noted)
Parameter Symbol Test Condition Min Typical Max Units
RF frequency range FRF 390 450 500 MHz
LO frequency range (Note 1) FLO 450 540 650 MHz
IF frequency range FIF 40 90 250 MHz
LO switching time 1 µs
Conversion gain G FRF= 435 to 487 MHz,
VCC = 4.75 to 5.25 V,
PLO = –3 to +3 dBm
8.3 9.3 dB
Gain variation over temperature FRF= 450 MHz,
TC = –40 to +85 °C
±0.7 dB
Noise Figure NF FRF= 450 MHz 9.3 11.0 dB
Noise Figure variation over temperature FRF= 450 MHz,
TC = –40 to +85 °C
±0.6 dB
Noise Figure with a blocker signal NFBLK Blocking signal input
power = +8 dBm
18 25 dB
Third order input intercept point IIP3 FRF= 450 and 450.8 MHz,
PRF = –10 dBm/each tone
VCC = 4.75 to 5.25 V,
PLO = –3 to +3 dBm
23.5 24.9 dBm
Input IP3 variation over temperature IIP3 FRF= 450 and 450.8 MHz,
TC = –40 to +85 °C
±1.2 dB
Third order output intercept point OIP3 FRF= 450 and 450.8 MHz,
PRF = –10 dBm/each tone
VCC = 4.75 to 5.25 V,
PLO = –3 to +3 dBm
34.2 dBm
2RF – 2LO 2x2 PRF = –10 dBm –74 –63 dBc
5RF – 4LO 5x4 PRF = +2 dBm –100 –93 dBc
Input 1 dB compression point IP1dB FRF= 435 to 487 MHz,
VCC = 4.75 to 5.25 V,
PLO = –3 to +3 dBm
9.5 12.9 dBm
Output 1 dB compression point OP1dB FRF= 435 to 487 MHz,
VCC = 4.75 to 5.25 V,
PLO = –3 to +3 dBm
21.2 dBm
LO1 to LO2 isolation Frf= 450 MHz,
Flo = 540 MHz
40 62 dB
Channel-to-channel isolation Frf= 450 MHz,
Flo = 540 MHz
30 46 dB
DATA SHEET • SKY73085-11 DOWNCONVERSION MIXER
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
200990B • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • April 1, 2009 5
Table 4. SKY73085-11 Electrical Specifications (2 of 2)
(Voltage Supply = +5 V, TC = +25 °C, LO = 0 dBm, RF Frequency = 450 MHz, IF Frequency = 90 MHz, LO Frequency = 540 MHz, Unless
Otherwise Noted)
Parameter Symbol Test Condition Min Typical Max Units
RF to IF isolation FRF= 450 MHz 30 63 dB
LO leakage:
1xLO to RF port
2xLO to RF port
3xLO to RF port
4xLO to RF port
1xLO to IF port
F
LO = 540 MHz
–30
–29
–44
–40
–40
–25
–25
–28
–28
–23
dBm
dBm
dBm
dBm
dBm
Note 1: The SKY73085-11 has been optimized for high-side LO injection. However, the LO can be used outside of the specified frequency range with degraded performance.
7.0
7.5
8.0
8.5
9.0
9.5
10.0
10.5
11.0
11.5
12.0
435 445 455 465 475 485
RF Frequency (MHz)
Gain (dB)
4.75 V
5.00 V
5.25 V
Figure 3. Mixer A Gain vs Frequency and Supply Voltage
435 445 455 465 475 485
RF Frequency (MHz)
Gain (dB)
7.0
7.5
8.0
8.5
9.0
9.5
10.0
10.5
11.0
11.5
12.0
–3 dBm
0 dBm
+3 dBm
Figure 5. Mixer A Gain vs Frequency and LO Power
435 445 455 465475485
RF Frequency (MHz)
Gain (dB)
7.0
7.5
8.0
8.5
9.0
9.5
10.0
10.5
11.0
11.5
12.0
–40 C
+25
o
C
+85 C
Figure 7. Mixer B Gain vs Frequency and Temperature
435 445 455 465 475 485
RF Frequency (MHz)
Gain (dB)
7.0
7.5
8.0
8.5
9.0
9.5
10.0
10.5
11.0
11.5
12.0
–40 C
+25
o
C
+85 C
Figure 4. Mixer A Gain vs Frequency and Temperature
7.0
7.5
8.0
8.5
9.0
9.5
10.0
10.5
11.0
11.5
12.0
435 445 455 465475 485
RF Frequency (MHz)
Gain (dB)
4.75 V
5.00 V
5.25 V
Figure 6. Mixer B Gain vs Frequency and Supply Voltage
435 445 455 465475485
RF Frequency (MHz)
Gain (dB)
7.0
7.5
8.0
8.5
9.0
9.5
10.0
10.5
11.0
11.5
12.0
–3 dBm
0 dBm
+3 dBm
Figure 8. Mixer B Gain vs Frequency and LO Power
DATA SHEET • SKY73085-11 DOWNCONVERSION MIXER
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
6 April 1, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200990B
7.0
7.5
8.0
8.5
9.0
9.5
10.0
10.5
11.0
11.5
12.0
435 445 455 465475485
RF Frequency (MHz)
Gain (dB)
4.75 V
5.00 V
5.25 V
Figure 9. Mixer A Noise Figure vs Frequency and Supply Voltage
20
21
22
23
24
25
26
27
28
29
30
435 445 455 465475485
RF Frequency (MHz)
IIP3 (dBm)
4.75 V
5.00 V
5.25 V
Figure 11. Mixer A IIP3 vs Frequency and Supply Voltage
435 445 455 465 475 485
RF Frequency (MHz)
IIP3 (dBm)
20
21
22
23
24
25
26
27
28
29
30
–3 dBm
0 dBm
+3 dBm
Figure 13. Mixer A IIP3 vs Frequency and LO Power
435 445 455 465 475 485
RF Frequency (MHz)
IIP3 (dBm)
20
21
22
23
24
25
26
27
28
29
30
–40 C
+25
o
C
+85 C
Figure 15. Mixer B IIP3 vs Frequency and Temperature
7.0
7.5
8.0
8.5
9.0
9.5
10.0
10.5
11.0
11.5
12.0
435 445 455 465475485
RF Frequency (MHz)
Noise Figure (dB)
4.75 V
5.00 V
5.25 V
Figure 10. Mixer B Noise Figure vs Frequency and Supply Voltage
435 445 455 465 475 485
RF Frequency (MHz)
IIP3 (dBm)
20
21
22
23
24
25
26
27
28
29
30
–40 C
+25
o
C
+85 C
Figure 12. Mixer A IIP3 vs Frequency and Temperature
20
21
22
23
24
25
26
27
28
29
30
435 445 455 465 475 485
RF Frequency (MHz)
IIP3 (dBm)
4.75 V
5.00 V
5.25 V
Figure 14. Mixer B IIP3 vs Frequency and Supply Voltage
435 445 455 465475485
RF Frequency (MHz)
IIP3 (dBm)
20
21
22
23
24
25
26
27
28
29
30
–3 dBm
0 dBm
+3 dBm
Figure 16. Mixer B IIP3 vs Frequency and LO Power
DATA SHEET • SKY73085-11 DOWNCONVERSION MIXER
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
200990B • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • April 1, 2009 7
70 80 90100110
RF Frequency (MHz)
2 x 2 (dBc)
–90
–85
–80
–75
–70
–65
–60
–55
–50
–40 C
+25
o
C
+85 C
Figure 17. Mixer A 2RF-2LO vs IF Frequency and Temperature
70 80 90100110
RF Frequency (MHz)
RF to IF Isolation (dB)
56
60
64
68
40
44
48
52
72
76
80
–40 C
+25
o
C
+85 C
Figure 19. Mixer A RF to IF Isolation vs IF Frequency and
Temperature
70 80 90100110
RF Frequency (MHz)
LO to IF Leakage (dBm)
–48
–45
–42
–39
–60
–57
–54
–51
–36
–33
–30
–40 C
+25
o
C
+85 C
Figure 21. Mixer A LO to IF Leakage vs Frequency and
Temperature
70 80 90100110
RF Frequency (MHz)
2 x 2 (dBc)
–90
–85
–80
–75
–70
–65
–60
–40 C
+25 oC
+85 C
Figure 18. Mixer B 2RF-2LO vs Frequency and Temperature
70 80 90 100 110
RF Frequency (MHz)
RF to IF Isolation (dB)
56
60
64
68
40
44
48
52
72
76
80
–40 C
+25 oC
+85 C
Figure 20. Mixer B RF to IF Isolation vs IF Frequency and
Temperature
70 80 90100110
RF Frequency (MHz)
LO to IF Leakage (dBm)
–48
–45
–42
–39
–60
–57
–54
–51
–36
–33
–30
–40 C
+25 oC
+85 C
Figure 22. Mixer B LO to IF Leakage vs IF Frequency and
Temperature
DATA SHEET • SKY73085-11 DOWNCONVERSION MIXER
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
8 April 1, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200990B
70 80 90 100 110
RF Frequency (MHz)
LO to RF Leakage (dBm)
–32
–30
–28
–26
–40
–38
–36
–34
–24
–22
–20
–40 C
+25
o
C
+85 C
Figure 23. Mixer A to RF Leakage vs Frequency and Temperature
70 80 90 100 110
RF Frequency (MHz)
Channel to Channel Isolation (dB)
36
40
44
48
20
24
28
32
52
56
60
–40 C
+25
o
C
+85 C
Figure 25. Channel A to Channel B IF Isolation vs Frequency and
Supply Voltage
4.75 5.00 5.25
Supply Voltage (V)
5RF-4LO (dBc)
–102
–100
–98
–96
–110
–108
–106
–104
–94
–92
–90
Mixer A
Mixer B
Figure 27. Mixer A and B 5RF-4LO vs Supply Voltage
70 80 90 100 110
RF Frequency (MHz)
LO to RF Leakage (dBm)
–32
–30
–28
–26
–40
–38
–36
–34
–24
–22
–20
–40 C
+25
o
C
+85 C
Figure 24. Mixer B LO to RF Leakage vs Frequency and
Temperature
–40 +25 +85
Temperature (°C)
5RF-4LO (dBc)
–102
–100
–98
–96
–110
–108
–106
–104
–94
–92
–90
Mixer A
Mixer B
Figure 26. Mixer A and B 5RF-4LO vs Temperature
–3 0 +3
LO Power (dBm)
5RF-4LO (dBc)
–102
–100
–98
–96
–110
–108
–106
–104
–94
–92
–90
Mixer A
Mixer B
Figure 28. Mixer A and B 5RF-4LO vs LO Power
DATA SHEET • SKY73085-11 DOWNCONVERSION MIXER
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
200990B • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • April 1, 2009 9
Evaluation Board Description
The SKY73085-11 Evaluation Board is used to test the
performance of the SKY73085-11 downconversion mixer. An
assembly drawing for the Evaluation Board is shown in Figure 29
and the layer detail is provided in Figure 30. A schematic diagram
of the SKY73085-11 Evaluation Board is shown in Figure 31.
Circuit Design Configurations
The following design considerations are general in nature and
must be followed regardless of final use or configuration:
1. Paths to ground should be made as short as possible.
2. The ground pad of the SKY73085-11 has special electrical
and thermal grounding requirements. This pad is the main
thermal conduit for heat dissipation. Since the circuit board
acts as the heat sink, it must shunt as much heat as possible
from the device. Therefore, design the connection to the
ground pad to dissipate the maximum wattage produced by
the circuit board.
3. Skyworks recommends including external bypass capacitors
on the VCC voltage inputs of the device.
4. Components L5, L6, L14, and L15 (see Figure 31) are high-Q
low loss inductors. These inductors must be able to pass
currents in excess of 200 mA DC.
5. Components R1 and R2 (see Figure 31) set the bias current
for the IF amplifiers. Skyworks recommends that these
resistors have a tolerance of ±1% to optimize performance
consistency of the SKY73085-11. These resistors are not
required for the Evaluation Board to operate as specified in
Tables 3 and 4.
Package Dimensions
The PCB layout footprint for the SKY73085-11 is provided in
Figure 32. Figure 33 shows the package dimensions for the
36-pin MCM and Figure 34 provides the tape and reel
dimensions.
Package and Handling Information
Since the device package is sensitive to moisture absorption, it is
baked and vacuum packed before shipping. Instructions on the
shipping container label regarding exposure to moisture after the
container seal is broken must be followed. Otherwise, problems
related to moisture absorption may occur when the part is
subjected to high temperature during solder assembly.
THE SKY73085-11 is rated to Moisture Sensitivity Level 3 (MSL3)
at 260 °C. It can be used for lead or lead-free soldering. For
additional information, refer to the Skyworks Application Note,
PCB Design & SMT Assembly/Rework Guidelines for MCM-L
Packages, document number 101752.
Care must be taken when attaching this product, whether it is
done manually or in a production solder reflow environment.
Production quantities of this product are shipped in a standard
tape and reel format. For packaging details, refer to the Skyworks
Application Note, Tape and Reel, document number 101568.
Electrostatic Discharge (ESD) Sensitivity
The SKY73085-11 is a static-sensitive electronic device. Do not
operate or store near strong electrostatic fields. Take proper ESD
precautions.
DATA SHEET • SKY73085-11 DOWNCONVERSION MIXER
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
10 April 1, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200990B
S90
5
J4
J1
J7
J6J10
J3
J8
J5J9
L16 L17 R4
R5
R2
L13
L11
L15
L12
C34 C35
C32
L14
C38
C33
C39 C24
C25
C27
C23
C21
C22
C17
L10
C18
C19
C40
R1
R6
C13
C14
C11
R3
T1
L8 L9
C16
C15
C37C36
L18 L19
C12
C41
C5
C4
C1
C3
L2
C2
L1
C8
C7
L4
C6
L3
L6L5
C20
C26
C29 C28
T2
J2
Figure 29. SKY73085-11 Evaluation Board Assembly Diagram
DATA SHEET • SKY73085-11 DOWNCONVERSION MIXER
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
200990B • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • April 1, 2009 11
S904
Layer 1: Top -- Metal
Layer 2: Ground
Layer 3: Power Plane
Layer 4: Solid Ground Plane
Figure 30. SKY73085-11 Evaluation Board Layer Detail
DATA SHEET • SKY73085-11 DOWNCONVERSION MIXER
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
12 April 1, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200990B
RFB
VCC3
NC
GND
IFB+
IFB–
NC
VCC4
RIFB
VCC7
NC
GND
IFA+
IFA–
NC
VCC6
RIFA
NC
VCC1
NC
GND
VCC2
GND
GND
NC
RFA
LO1
GND
GND
VCC5
GND
LO_SEL
GND
GND
LO2
J4
SKY73085-11
C1
0 Ω1
2
3
4
5
6
7
8
9
27
26
25
24
23
22
21
20
19
10 11 12 13 14 15 1617 18
3635 34 33 32 31 30 2928
L2
3.3 pF
L1
0 Ω
J7
C8
0 Ω
C2
56 nH
VCC
VCC
L4
3.3 pF
L5
470 nH
L8
39 nH
L6
470 nH
L3
0 Ω
L9
0 Ω
C16
33 pF
C35
33 pF
C17
33 pF
C21
33 pF
C22
12 pF
J6
T1
DB714
VCC
VCC
x
x
x
NC
x
x
x
x
x
L10
0 Ω
J3
VCC
VCC
VCC
VCC
C23
33 pF
L11
0 Ω
J8
R1
DNI
R3
0 Ω
C13
1 μF
Element Jumper
C20
1 μF
C14
33 pF
C26
1 μF
C27
33 pF
C28
33 pF
T2
DB714
VCC
J5
L13
39 nH
L14
470 nH
L15
470 nH
L12
0 Ω
R2
DNI
R4
0 Ω
S1334
Note: The SKY73085 Evaluation Board can be converted to
provide a differential output by removing components
T1, T2, R3, and R4.
Some component labels may be different than the
corresponding component symbol shown here.
Component values, however, are accurate as of the
date of this Data Sheet.
C6
56 nH
Figure 31. SKY73085-11 Evaluation Board Schematic
DATA SHEET • SKY73085-11 DOWNCONVERSION MIXER
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
200990B • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • April 1, 2009 13
S1125
Stencil Aperture
Top View
Metallization
Top View
Solder Mask Opening
Top View
6.3
0.15 0.075
0.75 0.9
0.25
0.4
0.075
6.3
12X 0.062
24X 0.125
12X 0.06324X 0.125
36X 0.875
36X 0.875
0.5
Pitch
Typ
Stencil aperture size for center
ground pads should be 80% to
100% (by area) of the solder
mask opening of the package.
Component Outline
Component Outline
SMT Pad Detail
Scale: 2X
9X This Rotation
9X Rotated 180o
9X Rotated 90o CW
9X Rotated 90o CCW
Stencil and
Metallization
Soldermask Opening
All measurements are in millimeters
2X 2.775
Thermal Via Array.
0.3 mm on 0.6 mm pitch.
Additional vias in common ground
pad will improve thermal and electrical
performance. NOTE: thermal vias
should be tented and filled with solder
mask, 30-35 μm Cu plating recommended.
Note: The cross-hatched area represents the merger of the center
ground pad +10 individual I/O ground pads. All I/O ground
pads should have at least one via connected to internal ground
planes for optimum electrical performance.
Pin 1
Pin 36
Component Outline
Component Outline
6.45
6.3
2X 2.775
0.25 Typ
6.45
6.3 3.88
Figure 32. PCB Layout Footprint for the SKY73085-11 6 x 6 mm MCM
DATA SHEET • SKY73085-11 DOWNCONVERSION MIXER
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
14 April 1, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200990B
All measurements are in millimeters
Pads are solder mask defined on one edge and metal
defined on three edges.
Dimensioning and tolerancing according to ASME Y14.5M-1994
S689_A
6
6
Pin 1 Indicator
Metal Pad Edge
1.1 ± 0.1
0.4 ± 0.05
0.5 ± 0.1
(0.1)
Side View
B
Bottom View
A
Detail A
Detail D
Top View
Pin 36
Pin 1
Pin 1 Indicator
(See Detail D)
0.25 ± 0.05
18X 2.9
0.2 x 0.2
Solder Mask Opening
36x SMT Pad
0.15 A B C
0.2 A B C
0.15 A B C
C
A
0.1
4X 2
4X 2
2X 1.9
2X 1.9
18X 2.9
3X R0.2
4X 1.5
4X 1.5
4X 1
4X 1
4X 0.5
4X 0.5
Figure 33. SKY73085-11 36-Pin MCM Package Dimensions
DATA SHEET • SKY73085-11 DOWNCONVERSION MIXER
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
200990B • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • April 1, 2009 15
S1183
Notes:
1. Carrier tape: black conductive polystyrene
2. Cover tape material: transparent conductive PSA
3. Cover tape size: 9.3 mm width
4. All dimensions are in millimeters
5. Pin 1 orientation is in top left corner for the following Skyworks products:
SKY73022-21, -31
SKY73023-21, -31
For all other 6 x 6 mm MCM/RFLGA products, pin 1 orientation is
in top right corner.
A
B
2.00 ± 0.05
∅1.50 ± 0.10
0.30 ± 0.02
7o Max.
8o Max.
6.35
1.75 ± 0.10
∅1.50 Min.
5.50 ± 0.05
8.00 4.00
A
B
B
A
1.59
12.00 ± 0.30
6.35
Pin #1 Indicator
(see Notes)
Figure 34. SKY73085-11 Tape and Reel Dimensions
DATA SHEET • SKY73085-11 DOWNCONVERSION MIXER
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
16 April 1, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200990B
Ordering Information
Model Name Manufacturing Part Number Evaluation Kit Part Number
SKY73085-11 390-500 MHz Downconversion Mixer SKY73085-11 (Pb-free package) TW17-D650
Copyright © 2008, 2009 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by
Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the
information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to
update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or
information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions
of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A
PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY
DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS
SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION,
LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury,
death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any
damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of
products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for
applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters.
Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands
and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com,
are incorporated by reference.
