1
CSM_E2EZ_DS_E_3_1
Chip-immune Inductive Proximity Sensor
E2EZ
Detects objects without being
influenced by aluminum or iron
chips.
• Series now includes M12 Models.
• Pre-wired Connector Models also available.
• CE Marking for DC 2-Wire and DC 3-Wire Models.
Be sure to read Safety Precautions on
page 7.
Ordering Information
Sensors [Refer to Dimensions on page 8.]
Pre-wired Models
Pre-wired Smartclick Connector Models (M12)
Appearance Sensing distance Output configuration
Model
Operation mode
NO NC
M12 DC 2-Wire Models E2EZ-X2D1-N 2M E2EZ-X2D2-N 2M
M18
DC 3-wire, NPN E2EZ-X4C1 2M —
DC 2-wire E2EZ-X4D1-N 2M E2EZ-X4D2-N 2M
AC 2-wire E2EZ-X4Y1 2M —
M30
DC 3-wire, NPN E2EZ-X8C1 2M —
DC 2-wire E2EZ-X8D1-N 2M E2EZ-X8D2-N 2M
AC 2-wire E2EZ-X8Y1 2M
Shielded
2 mm
4 mm
8 mm
Appearance Sensing distance Output configuration
Model
Operation mode
NO NC
M12
DC 2-wire, (3)-(4) pin arrangement E2EZ-X2D1-M1TJ 0.3M —
DC 2-wire, (1)-(4) pin arrangement E2EZ-X2D1-M1TGJ 0.3M —
M18
DC 2-wire, (3)-(4) pin arrangement E2EZ-X4D1-M1TJ 0.3M —
DC 2-wire, (1)-(4) pin arrangement E2EZ-X4D1-M1TGJ 0.3M —
M30
DC 2-wire, (3)-(4) pin arrangement E2EZ-X8D1-M1TJ 0.3M —
DC 2-wire, (1)-(4) pin arrangement E2EZ-X8D1-M1TGJ 0.3M —
Shielded
2 mm
4 mm
8 mm
E2EZ
2
Pre-wired Connector Models (M12)
Accessories (Order Separately)
Sensor I/O Connectors (M12) [Refer to Dimensions on XS2.]
Mounting Brackets
Protective Covers
Sputter Protective Covers
Refer to Y92
@
for details.
Appearance Sensing distance Output configuration
Model
Operation mode
NO NC
M12
DC 2-wire, (3)-(4) pin arrangement E2EZ-X2D1-M1J 0.3M —
DC 2-wire, (1)-(4) pin arrangement E2EZ-X2D1-M1GJ 0.3M —
M18
DC 2-wire, (3)-(4) pin arrangement E2EZ-X4D1-M1J 0.3M —
DC 2-wire, (1)-(4) pin arrangement E2EZ-X4D1-M1GJ 0.3M —
M30
DC 2-wire, (3)-(4) pin arrangement E2EZ-X8D1-M1J 0.3M —
DC 2-wire, (1)-(4) pin arrangement E2EZ-X8D1-M1GJ 0.3M —
Shielded
2 mm
4 mm
8 mm
Appearance Cable length Sensor I/O Connector model number Applicable Proximity Sensor model number
Straight
2 m XS2F-D421-DD0
E2EZ-X2D@-M1J
E2EZ-X4D@-M1J
E2EZ-X8D@-M1J
5 m XS2F-D421-GD0
L-shape
2 m XS2F-D422-DD0
5 m XS2F-D422-GD0
Straight
2 m XS2F-D421-DA0-A
E2EZ-X2D@-M1GJ
E2EZ-X4D@-M1GJ
E2EZ-X8D@-M1GJ
5 m XS2F-D421-GA0-A
L-shape
2 m XS2F-D422-DA0-A
5 m XS2F-D422-GA0-A
E2EZ
3
Ratings and Specifications
*1. Use the Sensor within the range in which the green indicator is ON.
*2. The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and
a set distance of half the sensing distance.
Model E2EZ-X2D@-N
E2EZ-X2D@-M1J
E2EZ-X2D@-M1GJ
E2EZ-X4D@-N
E2EZ-X4D@-M1J
E2EZ-X4D@-M1GJ
E2EZ-X8D@-N
E2EZ-X8D@-M1J
E2EZ-X8D@-M1GJ
E2EZ-X4C1
E2EZ-X4Y1
E2EZ-X8C1
E2EZ-X8Y1
Item
Sensing distance 2 mm ±10% 4 mm ±10% 8 mm ±10% 4 mm ±10% 8 mm ±10%
Set distance *10 to 1.6 mm 0 to 3.2 mm 0 to 6.4 mm 0 to 3.2 mm 0 to 6.4 mm
Differential travel 20% max. of sensing distance
Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 4.)
Standard sensing
object Iron, 12 × 12 × 1 mm Iron, 30 × 30 × 1 mm Iron, 54 × 54 × 1 mm Iron, 30 × 30 × 1 mm Iron, 54 × 54 × 1 mm
Response
frequency *2200 Hz 100 Hz 30 Hz C Models: 12 Hz
Y Models: 5 Hz
C Models: 8 Hz
Y Models: 5 Hz
Power supply volt-
age
(operating voltage
range)
12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max.
C Models: 12 to 24 VDC (10 to 30 VDC), ripple (p-p):
10% max.
Y Models: 100 to 220 VAC (90 to 250 VAC), 50/60 Hz
Current
consumption --- C Models: 15 mA max.
Leakage current 0.8 mA max. Y Models: 2 mA max. at 100 VAC, 3 mA max. at 200 VAC
Con-
trol
output
Load cur-
rent 3 to 100 mA max.
C Models: NPN open-collector output
100 mA max. at 12 VDC (30 VDC max.)
200 mA max. at 24 VDC (30 VDC max.)
Y Models: 10 to 200 mA
Residual
voltage 3 V max. (Load current: 100 mA, Cable length: 2 m)
C Models: 2 V max. (Load current: 200 mA, Cable length:
2 m)
Y Models: Refer to residual voltage characteristic data
Refer to page 4.
Indicators D1 Models: Operation indicator (red), Setting indicator (green)
D2 Models: Operation indicator (red)
C Models: Detection indicator (red)
Y Models: Operation indicator (red)
Operation mode
(with sensing ob-
ject approaching)
D1 Models: NO
D2 Models: NC
For details, refer to the Timing chart on page 5.
NO
For details, refer to the Timing chart on page 6.
Protection
circuits Load short-circuit protection, Surge suppressor
C Models: Load short-circuit protection, Reverse polarity
protection, Surge suppressor
Y Models: Surge suppressor
Ambient
temperature range Operating/Storage: 0 to 50°C (with no icing or condensation)
Ambient
humidity range Operating/Storage: 35% to 95% (with no condensation)
Temperature
influence ±20% max. of sensing distance at 23°C in the temperature range of 0 to 50°C
Voltage influence ±2.5% max. of sensing distance at rated voltage in the rated voltage ±10% range
Insulation
resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 1,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case
C Models: 1,000 VAC, 50/60 Hz for 1 min between cur-
rent-carrying parts and case
Y Models: 2,000 VAC, 50/60 Hz for 1 min between cur-
rent-carrying parts and case
Vibration
resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions
Degree of
protection IEC 60529 IP67, in-house standards: oil-resistant
Connection
method Pre-wired Models (Standard cable length: 2 m) and Pre-wired Connector Models
Weight
(packed state)
E2EZ-X2D@-N: Approx.
70 g
E2EZ-X2D@-M1J: Approx.
40 g
E2EZ-X2D@-M1GJ:
Approx. 40 g
E2EZ-X4D@-N: Approx.
160 g
E2EZ-X4D@-M1J:
Approx. 90 g
E2EZ-X4D@-M1GJ:
Approx. 90 g
E2EZ-X8D@-N: Approx.
220 g
E2EZ-X8D@-M1J:
Approx. 160 g
E2EZ-X8D@-M1GJ:
Approx. 160 g
Approx. 170 g Approx. 270 g
Materi-
als
Case Nickel-plated brass
Sensing
surface PBT Heat-resistant ABS
Clamp-
ing nuts Zinc-plated iron
Toothed
washer Zinc-plated iron
Accessories Instruction manual
E2EZ
4
Engineering Data (Typical)
Sensing Area
E2EZ-X2@E2EZ-X4@E2EZ-X8@
Influence of Sensing Object Size and Material
E2EZ-X2@E2EZ-X4@E2EZ-X8@
Residual Output Voltage
E2EZ-X@D@-N E2EZ-X4Y1/-X8Y1 at 100 VAC E2EZ-X4Y1/-X8Y1 at 200 VAC
0.5
1.0
1.5
Y
X
2.0
2.5
86420−2−4−6−8
0.0
Distance Y
(mm)
Sensing Head
Distance X (mm)
−2−4−6−8−10
0
1
2
3
Y
X
4
5
1086420
Distance Y
(mm)
Sensing Head
Distance X (mm)
0
1
2
3
4
5
6
−8−12−16−20
X
7
8
9
10
Y
201612840−4
Distance Y
(mm)
Sensing Head
Distance X (mm)
0
1
2
4
5
X
3
40302010
Side length of sensing object: d (mm)
Brass
Iron
Aluminum
Stainless steel
(SUS304)
Distance X (mm)
d ×
d t = 1 mm
0
2
4
8
10
X
6
605040302010
d ×
d t = 1 mm
Side length of sensing object: d (mm)
Brass Iron Aluminum
Stainless
steel
(SUS304)
Copper
Distance X (mm)
010
2
4
6
8
10
X
6050403020
d ×
d t = 1 mm
Side length of sensing object: d (mm)
Iron
Brass
Aluminum
Copper
Stainless
steel
(SUS304)
Distance X (mm)
10531
0
1
2
3
4
5
1,0005003001005030
Load current (mA)
Residual output voltage (V)
50 A
V
ON
100 VAC
OFF
200150100501050
100
Residual output
voltage
Residual load
voltage
Load voltage (V)
Load current (mA)
ON
200 VAC
V
A
100
150
200
0
50
105 20015010050
OFF
Residual output
voltage
Residual
load
voltage
Load voltage (V)
Load current (mA)
E2EZ
5
I/O Circuit Diagrams
DC 2-Wire Models
Leakage Current
E2EZ-X4Y1/-X8Y1 E2EZ-X@D@-N
Opera-
tion
mode
Model Timing chart Output circuit
NO
E2EZ-X2D1-N
E2EZ-X4D1-N
E2EZ-X8D1-N
E2EZ-X2D1-M1J
E2EZ-X2D1-M1GJ
E2EZ-X4D1-M1J
E2EZ-X4D1-M1GJ
E2EZ-X8D1-M1J
E2EZ-X8D1-M1GJ
NC
E2EZ-X2D2-N
E2EZ-X4D2-N
E2EZ-X8D2-N
1
2
3
4
5
6A
25020015010090
AC power
Power supply voltage (V)
Leakage current (mA)
Protective
resistance
02010
0.5
1.0
1.5
4030
Power supply voltage (V)
Leakage current (mA)
0
80(TYP)
100
(%)
Sensing
object
Rated sensing
distance
Stable sensing area
Non-sensing
area
Unstable
sensing
area
Set position
ON
OFF
ON
OFF
ON
OFF
Setting indicator
(green)
Operation
indicator (red)
Control output
0 V
+V
Load
Brown
Blue
Prox-
imity
Sensor
main
circuit
Note: The load can be connected to either the
+V or 0 V side.
4
3
(M1J)
+V
0 V
1
4
0 V
+V
4
2
1
3
4
2
1
3
Load
Prox-
imity
Sensor
main
circuit
Note: The load can be connected to either the +V or 0 V side.
Load
Prox-
imity
Sensor
main
circuit
Note: The load can be connected to either the +V or 0 V side.
Connector Pin
Arrangement
Note: Pins 1 and 2
are not used.
Connector Pin
Arrangement
Note: Pins 2 and 3
are not used.
(M1GJ)
0100
(%)
Sensing
object
Rated sensing
distance
Sensing areaNon-sensing area
ON
OFF
ON
OFF
Operation
indicator (Red)
Control output
0 V
+V
Load
Brown
Blue
Prox-
imity
Sensor
main
circuit
Note: The load can be connected to either the
+V or 0 V side.
E2EZ
6
DC 3-wire Models
AC 2-Wire Models
Connections for Sensor I/O Connectors
Operation
mode Model Timing chart Output circuit
NO E2EZ-X4C1
E2EZ-X8C1
Operation
mode Model Timing chart Output circuit
NO E2EZ-X4Y1
E2EZ-X8Y1
Present
Not present
Operate
Reset
ON
OFF
Sensing object
Load
Detection indicator (red)
2.2 Ω
+V
*
0 V
Proximity
Sensor
main
circuit
Load
Brown
Black
Output
Blue
* 100 mA max. at 12 V, 200 mA max. at 24 V
(load current).
Present
Not present
Operate
Reset
ON
OFF
Sensing object
Load
Operation indicator (red)
Load
Brown
Blue
Prox-
imity
Sensor
main
circuit
Proximity Sensor Sensor I/O Connectors
Connections
Model Operation
mode Model Model
DC 2-Wire Models
(IEC pin wiring)
NO
E2EZ-X@D1-M1GJ
DC 2-Wire Models
(previous pin wir-
ing)
E2EZ-X@D1-M1J
XS2F-D42@-@A0-A
1: Straight
2: L-shape
D: 2-m cable
G: 5-m cable
XS2F
4
3
2
1
4
3
2
1
E2EZ
main
circuit
Brown (+)
Blue (−)
XS2F-D42@-@D0
1: Straight
2: L-shape
D: 2-m cable
G: 5-m cable
2
XS2F
4
3
2
1
4
3
1
E2EZ
main
circuit
Blue (−)
Brown (+)
Refer to the Sensor I/O Connector Group Catalog (Cat. No. X073) for details.
E2EZ
7
Safety Precautions
Refer to Warranty and Limitations of Liability.
This product is not designed or rated for ensuring
safety of persons either directly or indirectly.
Do not use it for such purposes.
Do not use this product under ambient conditions that exceed the
ratings.
● Design
Influence of Surrounding Metal
When mounting the Sensor within a metal panel, ensure that the
clearances given in the following table are maintained. Failure to
maintain these distances may cause deterioration in the performance
of the Sensor.
Influence of Surrounding Metal (Unit: mm)
Mutual Interference
When installing Sensors face-to-face or side-by-side, ensure that the
minimum distances given in the following table are maintained.
Aluminum and Iron Cuttings
Normally aluminum or iron cuttings will not be detected even if they
adhere to or accumulate on the sensing surface.
Detection signals may be output for the following:
If this occurs, remove the cuttings from the sensing surface.
1. Relationship between the Size of the Cutting (d) and the Size of
the Sensing Surface (D)
Cuttings of the size d ≥ D on the sensing surface *
● Mounting
Do not tighten the nut with excessive force.
A washer must be used with the nut.
Note: 1. The allowable tightening strength depends on the distance from the
edge of the head, as shown in the following table. (A is the distance
from the edge of the head. B includes the nut on the head side. If the
edge of the nut is in part A, the tightening torque for part A applies
instead.)
2. The following torque assume washers are being used.
WARNING
Precautions for Correct Use
Item
l d D m n
Model
Embedded
material
E2EZ-X2@Iron 0120 818
Aluminum 2252 36
E2EZ-X4@Iron 018016 27
Aluminum 5405 54
E2EZ-X8@Iron 030032 45
Aluminum 10 70 10 90
D
d dia.
m
n
l
Mutual Interference (Unit: mm)
Model Item A B
E2EZ-X2@30 20
E2EZ-X4@40 50
E2EZ-X8@60 100
A
B
Tightening
Torque Part A Part B
Model
Dimension
(mm) Torque Torque
E2EZ-X2D@-@30 N·m
E2EZ-X4D@-@70 N·m
E2EZ-X8D@-@180 N·m
E2EZ-X4C1
E2EZ-X4Y1 20 15 N·m 29 N·m
E2EZ-X8C1
E2EZ-X8Y1 22 29 N·m 39 N·m
2
3
D
d
Sensing
surface
Cutting
Cutting
Pressed against
sensing surface.
Cuttings of the size d*(Unit: mm)
*E2EZ-X2@: d ≥ D on the sensing surface.
2. Cuttings Pressed against the Sensing
Surface
Model Size D
E2EZ-X2@10 *
E2EZ-X4@16
E2EZ-X8@28
1
3
Part B Part A
E2EZ
8
Dimensions
Mounting Hole Dimensions
(Unit: mm)
Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified.
38 9
10
33
17 4
21 dia.
*1
M12 × 1
15 dia.
M12 × 1
Indicator*2
Two clamping nuts
Toothed washer
*1. 4-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.3 mm2,
Insulator diameter: 1.3 mm), Standard length: 2 m
*2. D1 Models: Operation indicator (red), Setting indicator (green), D2 Models: Operation
indicator (red)
Pre-wired Connector Models (-M1J/M1GJ)
4-dia. vinyl-insulated round cable with
2 conductors (Conductor cross
section: 0.3 mm2, Insulator diameter:
1.3 mm), Standard length: 300 mm
E2EZ-X2D@-N
15 dia.
M12 × 1
Pre-wired Connector Models (-M1J/M1GJ)
6-dia. vinyl-insulated round cable with
2 conductors (Conductor cross section:
0.5 mm2, Insulator diameter: 1.9 mm),
Standard length: 300 mm
E2EZ-X4D@-N
43 12
10
38
4
24
29 dia.
M18 × 1
*1
Indicator*2
Two clamping nuts
Toothed washer
*1. 6-dia. vinyl-insulated round cable with 2 conduc
-
tors (Conductor cross section: 0.5 mm2, Insula-
tor diameter: 1.9 mm), Standard length: 2 m
The cable can be extended up to 200 m (sepa-
rate metal conduit).
*2. D1 Models: Operation indicator (red), Setting in-
dicator (green)
D2 Models: Operation indicator (red)
48 12
10
43
5
36
42 dia.
M30 × 1.5
*1
Indicator*2
Two clamping nuts
Toothed washer
*1. 6-dia. vinyl-insulated round cable with 2 con-
ductors (Conductor cross section: 0.5 mm2, In-
sulator diameter: 1.9 mm), Standard length: 2 m
The cable can be extended up to 200 m (sepa-
rate metal conduit).
*2. D1 Models: Operation indicator (red), Setting
indicator (green)
D2 Models: Operation indicator (red)
15 dia.
M12 × 1
Pre-wired Connector Models (-M1J/M1GJ)
6-dia. vinyl-insulated round cable with
2 conductors (Conductor cross section:
0.5 mm2, Insulator diameter: 1.9 mm),
Standard length: 300 mm
E2EZ-X8D@-N
E2EZ-X4C1
E2EZ-X4Y1
80
60
24
29 dia.
*1
M18 × 1
44
Two toothed washers Two clamping nuts
Indicator*2
*2. C Models: Detection indicator (red),
Y Models: Operation indicator (red)
*1. C Models: 6-dia. vinyl-insulated round cable with 3 conductors (Conductor cross
section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m
Y Models: 6-dia. vinyl-insulated round cable with 2 conductors (Conductor cross
section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m
E2EZ-X8C1
E2EZ-X8Y1 80
60
36
42 dia.
M30 × 1.5 55
*1
Two toothed washers Two clamping nuts
Indicator*2
*2. C Models: Detection indicator (red),
Y Models: Operation indicator (red)
*1. C Models: 6-dia. vinyl-insulated round cable with 3 conductors (Conductor cross
section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m
Y Models: 6-dia. vinyl-insulated round cable with 2 conductors (Conductor cross
section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m
Model F (mm)
E2EZ-X2@12.5 dia.
E2EZ-X4@18.5 dia.
E2EZ-X8@30.5 dia.
+0.5
−0
+0.5
−0
+0.5
−0
F
Read and Understand This Catalog
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or
comments.
Warranty and Limitations of Liability
WARRANTY
OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified)
from date of sale by OMRON.
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR
FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS
DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED.
LIMITATIONS OF LIABILITY
OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS
IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT
LIABILITY.
In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS
OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT
SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR.
Application Considerations
SUITABILITY FOR USE
OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's
application or use of the products.
At the customer's request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the
products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product,
machine, system, or other application or use.
The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible
uses of the products, nor is it intended to imply that the uses listed may be suitable for the products:
•
Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog.
•
Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles,
safety equipment, and installations subject to separate industry or government regulations.
•
Systems, machines, and equipment that could present a risk to life or property.
Please know and observe all prohibitions of use applicable to the products.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE
SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND
INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
PROGRAMMABLE PRODUCTS
OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof.
Disclaimers
CHANGE IN SPECIFICATIONS
Product specifications and accessories may be changed at any time based on improvements and other reasons.
It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made.
However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or
establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual
specifications of purchased products.
DIMENSIONS AND WEIGHTS
Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown.
PERFORMANCE DATA
Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the
result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON
Warranty and Limitations of Liability.
ERRORS AND OMISSIONS
The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical,
typographical, or proofreading errors, or omissions.
2008.11
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2008 All Right Reserved.
