[ /Title (CD74H C533, CD74H CT533, CD74H C563, CD74H CT563) /Subject (High Speed CD54/74HC533, CD54/74HCT533, CD54/74HC563, CD74HCT563 Data sheet acquired from Harris Semiconductor SCHS187C January 1998 - Revised July 2003 High-Speed CMOS Logic Octal Inverting Transparent Latch, Three-State Outputs Features Description * Common Latch-Enable Control The 'HC533, 'HCT533, 'HC563, and CD74HCT563 are high-speed Octal Transparent Latches manufactured with silicon gate CMOS technology. They possess the low power consumption of standard CMOS integrated circuits, as well as the ability to drive 15 LSTTL devices. * Common Three-State Output Enable Control * Buffered Inputs * Three-State Outputs The outputs are transparent to the inputs when the latch enable (LE) is high. When the latch enable (LE) goes low the data is latched. The output enable (OE) controls the three-state outputs. When the output enable (OE) is high the outputs are in the high impedance state. The latch operation is independent of the state of the output enable. * Bus Line Driving Capacity * Typical Propagation Delay = 13ns at VCC = 5V, CL = 15pF, TA = 25oC (Data to Output) * Fanout (Over Temperature Range) - Standard Outputs . . . . . . . . . . . . . . . 10 LSTTL Loads - Bus Driver Outputs . . . . . . . . . . . . . 15 LSTTL Loads The 'HC533 and 'HCT533 are identical in function to the 'HC563 and CD74HCT563 but have different pinouts. The 'HC533 and 'HCT533 are similar to the 'HC373 and 'HCT373; the latter are non-inverting types. * Wide Operating Temperature Range . . . -55oC to 125oC * Balanced Propagation Delay and Transition Times Ordering Information * Significant Power Reduction Compared to LSTTL Logic ICs * HC Types - 2V to 6V Operation - High Noise Immunity: NIL = 30%, NIH = 30% of VCC at VCC = 5V PART NUMBER * HCT Types - 4.5V to 5.5V Operation - Direct LSTTL Input Logic Compatibility, VIL= 0.8V (Max), VIH = 2V (Min) - CMOS Input Compatibility, Il 1A at VOL, VOH TEMP. RANGE (oC) CD54HC533F3A -55 to 125 20 Ld CERDIP CD54HC563F3A -55 to 125 20 Ld CERDIP CD54HCT533F3A -55 to 125 20 Ld CERDIP CD74HC533E -55 to 125 20 Ld PDIP CD74HC563E -55 to 125 20 Ld PDIP CD74HC563M -55 to 125 20 Ld SOIC CD74HCT533E -55 to 125 20 Ld PDIP CD74HCT563E -55 to 125 20 Ld PDIP CD74HCT563M -55 to 125 20 Ld SOIC CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures. Copyright (c) 2003, Texas Instruments Incorporated 1 PACKAGE CD54/74HC533, CD54/74HCT533, CD54/74HC563, CD74HCT563 Pinouts CD54HC533, CD54HCT533 (CERDIP) CD74HC533, CD74HCT533 (PDIP) TOP VIEW CD54HC563 (CERDIP) CD74HC563, CD74HCT563 (PDIP, SOIC) TOP VIEW OE 1 20 VCC OE 1 Q0 2 19 Q7 D0 2 19 Q0 D0 3 18 D7 D1 3 18 Q1 20 VCC D1 4 17 D6 D2 4 17 Q2 Q1 5 16 Q6 D3 5 16 Q3 Q2 6 15 Q5 D4 6 15 Q4 D2 7 14 D5 D5 7 14 Q5 D3 8 13 D4 D6 8 13 Q6 Q3 9 12 Q4 D7 9 12 Q7 GND 10 11 LE GND 10 11 LE Functional Block Diagram HC/HCT533 D0 D1 D O D2 D G O D3 D G O D4 O D G D5 D G O D6 D G O D7 D G O D G O G LE OE O0 O1 O2 O3 O4 O5 O6 O7 TRUTH TABLE OUTPUT ENABLE LATCH ENABLE DATA Q OUTPUT L H H L L H L H L L l H L L h L H X X Z H = High Voltage Level, L = Low Voltage Level, X = Don't Care, Z = High Impedance State, l = Low voltage level one set-up time prior to the high to low latch enable transition, h = High voltage level one set-up time prior to the high to low latch enable transition. 2 CD54/74HC533, CD54/74HCT533, CD54/74HC563, CD74HCT563 Absolute Maximum Ratings Thermal Information DC Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 7V DC Input Diode Current, IIK For VI < -0.5V or VI > VCC + 0.5V . . . . . . . . . . . . . . . . . . . . . .20mA DC Output Diode Current, IOK For VO < -0.5V or VO > VCC + 0.5V . . . . . . . . . . . . . . . . . . . .20mA DC Drain Current, per Output, IO For -0.5V < VO < VCC + 0.5V. . . . . . . . . . . . . . . . . . . . . . . . . .35mA DC Output Source or Sink Current per Output Pin, IO For VO > -0.5V or VO < VCC + 0.5V . . . . . . . . . . . . . . . . . . . .25mA DC VCC or Ground Current, ICC . . . . . . . . . . . . . . . . . . . . . . . . .50mA Thermal Resistance (Typical, Note 1) JA (oC/W) E (PDIP) Package . . . . . . . . . . . . . . . . . . . . . . . . . . 69 M (SOIC) Package. . . . . . . . . . . . . . . . . . . . . . . . . . 58 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) Operating Conditions Temperature Range, TA . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC Supply Voltage Range, VCC HC Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2V to 6V HCT Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.5V to 5.5V DC Input or Output Voltage, VI, VO . . . . . . . . . . . . . . . . . 0V to VCC Input Rise and Fall Time 2V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000ns (Max) 4.5V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500ns (Max) 6V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400ns (Max) CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. The package thermal impedance is calculated in accordance with JESD 51-7. DC Electrical Specifications TEST CONDITIONS PARAMETER SYMBOL VI (V) VIH - 25oC IO (mA) VCC (V) -40oC TO 85oC -55oC TO 125oC MIN TYP MAX MIN MAX MIN MAX UNITS 2 1.5 - - 1.5 - 1.5 - V 4.5 3.15 - - 3.15 - 3.15 - V 6 4.2 - - 4.2 - 4.2 - V HC TYPES High Level Input Voltage Low Level Input Voltage High Level Output Voltage CMOS Loads VIL VOH - VIH or VIL High Level Output Voltage TTL Loads Low Level Output Voltage CMOS Loads VOL VIH or VIL Low Level Output Voltage TTL Loads Input Leakage Current Quiescent Device Current - - 2 - - 0.5 - 0.5 - 0.5 V 4.5 - - 1.35 - 1.35 - 1.35 V 6 - - 1.8 - 1.8 - 1.8 V -0.02 2 1.9 - - 1.9 - 1.9 - V -0.02 4.5 4.4 - - 4.4 - 4.4 - V -0.02 6 5.9 - - 5.9 - 5.9 - V -6 4.5 3.98 - - 3.84 - 3.7 - V -7.8 6 5.48 - - 5.34 - 5.2 - V 0.02 2 - - 0.1 - 0.1 - 0.1 V 0.02 4.5 - - 0.1 - 0.1 - 0.1 V 0.02 6 - - 0.1 - 0.1 - 0.1 V 6 4.5 - - 0.26 - 0.33 - 0.4 V 7.8 6 - - 0.26 - 0.33 - 0.4 V II VCC or GND - 6 - - 0.1 - 1 - 1 A ICC VCC or GND 0 6 - - 8 - 80 - 160 A 3 CD54/74HC533, CD54/74HCT533, CD54/74HC563, CD74HCT563 DC Electrical Specifications (Continued) TEST CONDITIONS 25oC SYMBOL VI (V) IO (mA) VCC (V) - VIL or VIH VO = VCC or GND High Level Input Voltage VIH - Low Level Input Voltage VIL High Level Output Voltage CMOS Loads VOH PARAMETER Three-State Leakage Current -40oC TO 85oC -55oC TO 125oC MIN TYP MAX MIN MAX MIN MAX UNITS 6 - - 0.5 - 5 - 10 A - 4.5 to 5.5 2 - - 2 - 2 - V - - 4.5 to 5.5 - - 0.8 - 0.8 - 0.8 V VIH or VIL -0.02 4.5 4.4 - - 4.4 - 4.4 - V -6 4.5 3.98 - - 3.84 - 3.7 - V 0.02 4.5 - - 0.1 - 0.1 - 0.1 V 6 4.5 - - 0.26 - 0.33 - 0.4 V HCT TYPES High Level Output Voltage TTL Loads Low Level Output Voltage CMOS Loads VOL VIH or VIL Low Level Output Voltage TTL Loads II VCC to GND - 5.5 - - 0.1 - 1 - 1 A ICC VCC or GND 0 5.5 - - 8 - 80 - 160 A Three-State Leakage Current - VIL or VIH VO = VCC or GND 5.5 - - 0.5 - 5 - 10 A Additional Quiescent Device Current Per Input Pin: 1 Unit Load ICC (Note 2) VCC -2.1 - 4.5 to 5.5 - 100 360 - 450 - 490 A Input Leakage Current Quiescent Device Current NOTE: 2. For dual-supply systems theoretical worst case (VI = 2.4V, VCC = 5.5V) specification is 1.8mA. HCT Input Loading Table INPUT UNIT LOADS D0 - D7 0.15 LE 0.30 OE 0.55 NOTE: Unit Load is ICC limit specified in DC Electrical Specifications table, e.g., 360A max at 25oC. 4 CD54/74HC533, CD54/74HCT533, CD54/74HC563, CD74HCT563 Prerequisite For Switching Specifications PARAMETER 25oC -40oC TO 85oC -55oC TO 125oC SYMBOL TEST CONDITIONS VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS tW - 2 80 - - 100 - 120 - ns 4.5 16 - - 20 - 24 - ns 6 14 - - 17 - 20 - ns 2 50 - - 65 - 75 - ns 4.5 10 - - 13 - 15 - ns 6 9 - - 11 - 13 - ns 2 35 - - 45 - 55 - ns 4.5 7 - - 9 - 11 - ns 6 6 - - 8 - 7 - ns 2 4 - - 4 - 4 - ns 4.5 4 - - 4 - 4 - ns 6 4 - - 4 - 4 - ns HC TYPES LE Pulse Width Set-up Time Data to LE tSU Hold Time, Data to LE (533) - tH Hold Time, Data to LE (563) - tH - HCT TYPES LE Pulse Width tw - 4.5 16 - - 20 - 24 - ns Set-up Time Data to LE tw - 4.5 10 - - 13 - 15 - ns Hold Time, Data to LE (533) tH - 4.5 8 - - 10 - 12 - ns Hold Time, Data to LE (563) tH - 4.5 5 - - 5 - 5 - ns Switching Specifications PARAMETER HC TYPES Propagation Delay, Data to Qn (HC533) Input tr, tf = 6ns Propagation Delay, LE to Qn (HC533) -55oC TO 125oC TEST CONDITIONS VCC (V) TYP MAX MAX MAX UNITS tPLH, tPHL CL = 50pF 2 - 165 205 250 ns 4.5 - 33 41 50 ns 6 - 28 35 43 ns 5 13 - - - ns tPLH, tPHL tPLH, tPHL CL = 50pF 2 - 150 190 225 ns 4.5 - 30 38 45 ns 6 - 26 33 38 ns CL = 15pF 5 12 - - - ns CL = 50pF 2 - 175 220 265 ns 4.5 - 35 44 53 ns 6 - 30 37 45 ns 5 14 - - - ns CL = 15pF Propagation Delay, LE to Qn (HC563) -40oC TO 85oC SYMBOL CL = 15pF Propagation Delay, Data to Qn (HC563) 25oC tPLH, tPHL CL = 50pF CL = 15pF 2 - 165 205 250 ns 4.5 - 33 41 50 ns 6 - 28 35 43 ns 5 13 - - - ns 5 CD54/74HC533, CD54/74HCT533, CD54/74HC563, CD74HCT563 Switching Specifications PARAMETER Enable Times (HC533) Disable Times (HC533) Input tr, tf = 6ns (Continued) SYMBOL TEST CONDITIONS tPZH, tPZL CL = 50pF tPHZ, tPLZ tPZH, tPZL, tPHZ, tPLZ VCC (V) -40oC TO 85oC -55oC TO 125oC TYP MAX MAX MAX UNITS 2 - 150 190 225 ns 4.5 - 30 38 45 ns 6 - 26 33 38 ns CL = 15pF 5 12 - - - ns CL = 50pF 2 - 150 190 225 ns 4.5 - 30 38 45 ns 6 - 26 33 38 ns 5 12 - - - ns CL = 15pF Enable and Disable Times (HC563) 25oC CL = 50pF 2 - 150 190 225 ns 4.5 - 30 38 45 ns 6 - 26 33 38 ns CL = 15pF 5 12 - - - ns Input Capacitance CI - - - 10 10 10 pF Three-State Output Capacitance CO - - - 20 20 20 pF Power Dissipation Capacitance (Notes 3, 4) CPD - 5 42 - - - pF tPLH, tPHL CL = 50pF 4.5 - 34 43 51 ns CL = 15pF 5 14 - - - ns CL = 50pF 4.5 - 30 38 45 ns CL = 15pF 5 12 - - - ns CL = 50pF 4.5 - 38 48 57 ns CL = 15pF 5 16 - - - ns CL = 50pF 4.5 - 35 44 53 ns CL = 15pF 5 14 - - - ns CL = 50pF 4.5 - 35 44 53 ns CL = 15pF 5 14 - - - ns CL = 50pF 4.5 - 30 38 45 ns CL = 15pF 5 12 - - - ns HCT TYPES Propagation Delay, Data to Qn (HC/HCT533) Propagation Delay, Data to Qn (HC/HCT563) tPLH, tPHL Propagation Delay, LE to Qn (HC/HCT533) tPLH, tPHL Propagation Delay, LE to Qn (HC/HCT563) tPZL, tPZH Enable Times (HC/HCT533) tPLZ, tPZH Disable Times (HC/HCT533) tTLH, tTHL Enable and Disable Times (HC/HCT563) tPZH, tPZL, tPHZ, tPLZ CL = 50pF 4.5 - 35 44 53 ns CL = 15pF 5 14 - - - ns Input Capacitance CI - - - 10 10 10 pF Power Dissipation Capacitance (Notes 3, 4) CPD - 5 42 - - - pF NOTES: 3. CPD is used to determine the no-load dynamic power consumption, per latch. 4. PD (total power per latch) = CPD VCC2 fi + CL VCC2 fo where fi = Input Frequency, fo = Output Frequency, CL = Output Load Capacitance, VCC = Supply Voltage. 6 CD54/74HC533, CD54/74HCT533, CD54/74HC563, CD74HCT563 Test Circuits and Waveforms tWL + tWH = tfCL trCL 50% 10% 10% tf = 6ns tr = 6ns tTLH 90% INVERTING OUTPUT tPHL FIGURE 3. HC TRANSITION TIMES AND PROPAGATION DELAY TIMES, COMBINATION LOGIC tPLH FIGURE 4. HCT TRANSITION TIMES AND PROPAGATION DELAY TIMES, COMBINATION LOGIC trCL tfCL VCC tfCL GND 1.3V 0.3V GND tH(H) tH(L) VCC DATA INPUT 3V 2.7V CLOCK INPUT 50% tH(H) tTLH 1.3V 10% tPLH 10% GND tTHL 90% 50% 10% 90% 3V 2.7V 1.3V 0.3V GND tTHL trCL tWH FIGURE 2. HCT CLOCK PULSE RISE AND FALL TIMES AND PULSE WIDTH INPUT INVERTING OUTPUT GND NOTE: Outputs should be switching from 10% VCC to 90% VCC in accordance with device truth table. For fMAX, input duty cycle = 50%. VCC 90% 50% 10% 1.3V 1.3V tWL tf = 6ns tPHL 1.3V 0.3V tWH FIGURE 1. HC CLOCK PULSE RISE AND FALL TIMES AND PULSE WIDTH INPUT 2.7V 0.3V GND tr = 6ns DATA INPUT 50% tH(L) 3V 1.3V 1.3V 1.3V GND tSU(H) tSU(H) tSU(L) tTLH 90% OUTPUT tTHL 90% 50% 10% tTLH 90% 1.3V OUTPUT tREM 3V SET, RESET OR PRESET GND tTHL 1.3V 10% FIGURE 5. HC SETUP TIMES, HOLD TIMES, REMOVAL TIME, AND PROPAGATION DELAY TIMES FOR EDGE TRIGGERED SEQUENTIAL LOGIC CIRCUITS tPHL 1.3V GND IC CL 50pF GND 90% tPLH 50% IC tSU(L) tPHL tPLH I fCL 3V NOTE: Outputs should be switching from 10% VCC to 90% VCC in accordance with device truth table. For fMAX, input duty cycle = 50%. tREM VCC SET, RESET OR PRESET tfCL = 6ns CLOCK 50% 50% tWL CLOCK INPUT tWL + tWH = trCL = 6ns VCC 90% CLOCK I fCL CL 50pF FIGURE 6. HCT SETUP TIMES, HOLD TIMES, REMOVAL TIME, AND PROPAGATION DELAY TIMES FOR EDGE TRIGGERED SEQUENTIAL LOGIC CIRCUITS 7 CD54/74HC533, CD54/74HCT533, CD54/74HC563, CD74HCT563 Test Circuits and Waveforms 6ns (Continued) 6ns OUTPUT DISABLE tr VCC 90% 50% 10% OUTPUTS ENABLED OUTPUT HIGH TO OFF 50% OUTPUTS DISABLED FIGURE 7. HC THREE-STATE PROPAGATION DELAY WAVEFORM OTHER INPUTS TIED HIGH OR LOW OUTPUT DISABLE IC WITH THREESTATE OUTPUT GND 1.3V tPZH 90% OUTPUTS ENABLED OUTPUTS ENABLED 0.3 10% tPHZ tPZH 90% 3V tPZL tPLZ OUTPUT LOW TO OFF 50% OUTPUT HIGH TO OFF 6ns GND 10% tPHZ tf 2.7 1.3 tPZL tPLZ OUTPUT LOW TO OFF 6ns OUTPUT DISABLE 1.3V OUTPUTS DISABLED OUTPUTS ENABLED FIGURE 8. HCT THREE-STATE PROPAGATION DELAY WAVEFORM OUTPUT RL = 1k CL 50pF VCC FOR tPLZ AND tPZL GND FOR tPHZ AND tPZH NOTE: Open drain waveforms tPLZ and tPZL are the same as those for three-state shown on the left. The test circuit is Output RL = 1k to VCC, CL = 50pF. FIGURE 9. HC AND HCT THREE-STATE PROPAGATION DELAY TEST CIRCUIT 8 PACKAGE OPTION ADDENDUM www.ti.com 25-Sep-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (C) Device Marking (3) (4/5) 5962-8606201RA ACTIVE CDIP J 20 1 TBD A42 N / A for Pkg Type -55 to 125 5962-8606201RA CD54HC563F3A 5962-8681301RA ACTIVE CDIP J 20 1 TBD A42 N / A for Pkg Type -55 to 125 5962-8681301RA CD54HC533F3A CD54HC533F3A ACTIVE CDIP J 20 1 TBD A42 N / A for Pkg Type -55 to 125 5962-8681301RA CD54HC533F3A CD54HC563F3A ACTIVE CDIP J 20 1 TBD A42 N / A for Pkg Type -55 to 125 5962-8606201RA CD54HC563F3A CD54HCT533F3A ACTIVE CDIP J 20 1 TBD A42 N / A for Pkg Type -55 to 125 CD54HCT533F3A CD74HC533E ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type -55 to 125 CD74HC533E CD74HC533EE4 ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type -55 to 125 CD74HC533E CD74HC563E ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type -55 to 125 CD74HC563E CD74HC563EE4 ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type -55 to 125 CD74HC563E CD74HCT533E ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type -55 to 125 CD74HCT533E CD74HCT533EE4 ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type -55 to 125 CD74HCT533E CD74HCT563E ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type -55 to 125 CD74HCT563E CD74HCT563EE4 ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type -55 to 125 CD74HCT563E CD74HCT563M ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 HCT563M CD74HCT563ME4 ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 HCT563M CD74HCT563MG4 ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 HCT563M (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 25-Sep-2013 LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF CD54HC533, CD54HC563, CD54HCT533, CD74HC533, CD74HC563, CD74HCT533 : * Catalog: CD74HC533, CD74HC563, CD74HCT533 * Military: CD54HC533, CD54HC563, CD54HCT533 NOTE: Qualified Version Definitions: * Catalog - TI's standard catalog product Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com 25-Sep-2013 * Military - QML certified for Military and Defense Applications Addendum-Page 3 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated