E M C C o m p o n e n t s May 2018 Chip beads For general signal line MMZ series MMZ2012 type MMZ2012 2012[0805 inch]* * Dimensions Code JIS[EIA] (2/11) E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 20180521 / beads_commercial_signal_mmz2012_en.fm (3/11) E M C C o m p o n e n t s Product compatible with RoHS directive Halogen-free Compatible with lead-free solders Chip beads For general signal line Overview of MMZ2012 type FEATURES Noise reduction solution for general signal line. Various frequency characteristics with 4 materials of different features for countermeasures against everything from general signals to high-speed signals. APPLICATION Noise removal for mobile devices such as smartphones and tablet terminals, and various modules. Noise removal for PCs and recorders, household appliances such as STBs, smart grids, and industrial equipment. PART NUMBER CONSTRUCTION MMZ Series name 2012 LxWxT dimensions (mm) 2012 2.0x1.25x0.85 R Material name D R S Y 150 A Impedance () at 100MHz 121 120 150 15 Characteristic type A B T 000 Packaging style Internal code T Taping 000 OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Operating Storage Type temperature temperature C C MMZ2012 -55 to +125 -55 to +125 The Storage temperature range is for after the circuit board is mounted. Package quantity Individual weight (pieces/reel) 4,000 mg 8 RoHS Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz2012_en.fm (4/11) E M C C o m p o n e n t s MMZ2012 type RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150C 180C Time t1 60 to 120s Soldering Temp. Time T3 t2 230C 30 to 60s Peak Temp. T4 250 to 260C Time t3 10s Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz2012_en.fm (5/11) E M C C o m p o n e n t s MMZ2012 type MATERIAL CHARACTERISTICS R material: For wide frequency applications calling for broad impedance characteristics. For digital signal line applications calling requiring good waveform integrity. Impedance values selected for effectiveness at 10 to 200MHz. S material: Standard type that features impedance characteristics similar to those of a typical ferrite core. For signal line applications in which the blocking region is near 100MHz. Impedance values selected for effectiveness at 40 to 300MHz. Y material: High frequency range type intended for the 100MHz region and above. For signal line applications in which the signal frequency is far from the cutoff frequency. Impedance values selected for effectiveness at 80 to 400MHz. D material: For applications calling for low insertion loss at low frequencies and sharply increasing impedance at high frequencies. Designed for high impedance at high frequencies (300MHz to 1GHz) for signal line applications. TYPICAL MATERIAL IMPEDANCE CHARACTERISTICS 2500 Impedance() 2000 Y 1500 1000 500 0 10 S D R 100 Frequency(MHz) 1000 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz2012_en.fm (6/11) E M C C o m p o n e n t s MMZ2012 type SHAPE & DIMENSIONS 0.850.2 1.250.2 20.2 0.50.3 Dimensions in mm 1.2 RECOMMENDED LAND PATTERN 0.8 1 0.8 Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz2012_en.fm (7/11) E M C C o m p o n e n t s MMZ2012 type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Impedance [100MHz] ( ) 15 30 60 120 300 600 1000 40 80 120 180 300 600 1000 15 30 60 120 300 600 1000 1500 2000 80 120 300 Tolerance 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% DC resistance Rated current Part No. ( )max. 0.05 0.05 0.10 0.12 0.15 0.20 0.30 0.10 0.10 0.15 0.15 0.20 0.30 0.35 0.05 0.05 0.10 0.12 0.15 0.20 0.30 0.40 0.50 0.30 0.30 0.50 (mA)max. 1500 1500 1000 800 600 500 500 1000 800 800 600 600 500 500 1500 1500 1000 800 600 500 500 500 400 500 500 400 MMZ2012R150AT000 MMZ2012R300AT000 MMZ2012R600AT000 MMZ2012R121AT000 MMZ2012R301AT000 MMZ2012R601AT000 MMZ2012R102AT000 MMZ2012S400AT000 MMZ2012S800AT000 MMZ2012S121AT000 MMZ2012S181AT000 MMZ2012S301AT000 MMZ2012S601AT000 MMZ2012S102AT000 MMZ2012Y150BT000 MMZ2012Y300BT000 MMZ2012Y600BT000 MMZ2012Y121BT000 MMZ2012Y301BT000 MMZ2012Y601BT000 MMZ2012Y102BT000 MMZ2012Y152BT000 MMZ2012Y202BT000 MMZ2012D800BT000 MMZ2012D121BT000 MMZ2012D301BT000 Measurement equipment Measurement item Product No. Impedance E4991A+16192A DC resistance Type-7556 Equivalent measurement equipment may be used. Manufacturer Keysight Technologies Yokogawa Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz2012_en.fm (8/11) E M C C o m p o n e n t s MMZ2012 type ELECTRICAL CHARACTERISTICS Z VS. FREQUENCY CHARACTERISTICS (BY SERIES) MMZ2012R series MMZ2012S series MMZ2012R102A MMZ2012R601A 1000 MMZ2012R301A MMZ2012R121A 900 MMZ2012R600A 800 MMZ2012R300A MMZ2012R150A 700 600 500 400 MMZ2012S181A 500 400 200 100 100 10000 2000 600 300 100 1000 Frequency (MHz) MMZ2012S601A MMZ2012S301A 700 200 10 MMZ2012Y202B MMZ2012S121A 800 300 0 1 2500 MMZ2012S102A 1000 MMZ2012S800A 900 MMZ2012S400A Impedance () 1100 1100 Impedance () 1200 Impedance () MMZ2012Y series 1200 0 1 MMZ2012Y600B MMZ2012Y152B MMZ2012Y300B MMZ2012Y102B 1500 MMZ2012Y150B MMZ2012Y601B MMZ2012Y301B MMZ2012Y121B 1000 500 10 100 1000 Frequency (MHz) 10000 0 1 10 100 1000 Frequency (MHz) 10000 MMZ2012D series 4500 4000 MMZ2012D301B Impedance () 3500 3000 2500 2000 MMZ2012D121B 1500 MMZ2012D800B 1000 500 0 1 10 100 1000 Frequency (MHz) 10000 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz2012_en.fm (9/11) E M C C o m p o n e n t s MMZ2012 type ELECTRICAL CHARACTERISTICS Z, X, R VS. FREQUENCY CHARACTERISTICS MMZ2012R150AT000 MMZ2012R300AT000 R X 10 100 1000 Frequency (MHz) 10000 140 120 100 80 60 40 20 0 1 Z R X 10 100 1000 Frequency (MHz) 10000 350 300 250 200 150 100 50 0 1 60 1000 50 Z 600 R 400 200 0 1 X 10 100 1000 Frequency (MHz) 700 600 500 400 300 200 100 0 1 X 100 1000 Frequency (MHz) 10000 Z 30 R 20 X 10 10 Z R 100 1000 Frequency (MHz) 10000 X 10 100 1000 Frequency (MHz) Z R 50 0 1 10000 140 120 100 80 60 40 20 0 1 X 10 100 1000 Frequency (MHz) 10000 Impedance () MMZ2012S102AT000 Z R X 10 200 100 100 1000 Frequency (MHz) 10000 450 400 350 300 250 200 150 100 50 0 1 30 1000 25 600 Z R 400 200 0 1 X 10 10 100 1000 Frequency (MHz) 10000 Z R X 10 100 1000 Frequency (MHz) 10000 Z R X 10 100 1000 Frequency (MHz) 10000 Z R X 10 100 1000 Frequency (MHz) 10000 MMZ2012Y150BT000 1200 800 X MMZ2012S301AT000 250 150 R MMZ2012S800AT000 300 Impedance () Impedance () Impedance () R 10 Z MMZ2012R601AT000 MMZ2012S181AT000 MMZ2012S601AT000 700 600 500 400 300 200 100 0 1 10000 Z 40 0 1 10000 MMZ2012S121AT000 180 160 140 120 100 80 60 40 20 0 1 100 1000 Frequency (MHz) MMZ2012S400AT000 1200 Impedance () Impedance () MMZ2012R102AT000 800 10 MMZ2012R301AT000 Impedance () Impedance () MMZ2012R121AT000 X Impedance () 0 1 R Impedance () 5 Z Impedance () Z 10 90 80 70 60 50 40 30 20 10 0 1 Impedance () 15 Impedance () Impedance () 20 Impedance () 40 0 35 30 25 20 15 10 5 0 1 25 MMZ2012R600AT000 100 1000 Frequency (MHz) 10000 Z 20 R 15 10 X 5 0 1 10 100 1000 Frequency (MHz) 10000 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz2012_en.fm (10/11) E M C C o m p o n e n t s MMZ2012 type ELECTRICAL CHARACTERISTICS 120 40 100 Z 30 R 20 10 X 100 1000 Frequency (MHz) Impedance () Impedance () Z R 300 200 100 0 1 X 10 100 1000 Frequency (MHz) 10000 Z R X 10 100 1000 Frequency (MHz) 10 100 1000 Frequency (MHz) 800 700 600 500 400 300 200 100 0 Z R 100 50 0 1 10000 X 10 100 1000 Frequency (MHz) 10000 MMZ2012Y102BT000 1200 1000 Z R X 1 10 100 1000 Frequency (MHz) R 400 X 200 10 100 1000 Frequency (MHz) 10000 MMZ2012D800BT000 Z 1500 1000 X R 10 Z 600 0 1 10000 2000 500 800 100 1000 Frequency (MHz) 10000 700 600 500 400 300 200 100 0 1 Z 10 X R 100 1000 Frequency (MHz) 10000 MMZ2012D301BT000 Impedance () 1000 Impedance () 1 0 1 10000 1200 800 600 400 0 1 X 20 150 2500 MMZ2012D121BT000 200 40 MMZ2012Y202BT000 Impedance () Impedance () MMZ2012Y152BT000 1800 1600 1400 1200 1000 800 600 400 200 0 1 R MMZ2012Y601BT000 600 500 400 Z 60 0 10000 MMZ2012Y301BT000 80 Impedance () 10 200 Impedance () 0 1 MMZ2012Y121BT000 Impedance () 50 Impedance () Impedance () Z, X, R VS. FREQUENCY CHARACTERISTICS MMZ2012Y300BT000 MMZ2012Y600BT000 Z X R 10 100 1000 Frequency (MHz) 10000 4500 4000 3500 3000 2500 2000 1500 1000 500 0 1 Z R 10 X 100 1000 Frequency (MHz) 10000 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz2012_en.fm (11/11) E M C C o m p o n e n t s MMZ2012 type PACKAGING STYLE REEL DIMENSIONS o60min. 2.00.5 1.0 8.4 +2.0 -0.0 o130.2 o210.8 14.4max. o1802.0 Dimensions in mm 4.00.1 B 8.00.3 2.00.05 3.50.05 1.5 +0.1 0 1.750.1 TAPE DIMENSIONS K 4.00.1 A Dimensions in mm Type MMZ2012 160min. Drawing direction A 1.50.2 Taping B 2.30.2 P1 4.00.1 K 1.1max. 200min. 300min. Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz2012_en.fm