NUMBER TYPE 110-435G PRODUCT SPECIFICATION TITLE PAGE 0.5mm Pitch FPC/FFC Connector 62674-_ _ 11_1ALF REVISION 1 of 10 AUTHORIZED BY Sei Watanabe B DATE 2010-5-19 CLASSIFICATION UNRESTRICTED Table of Contents 1 SCOPE ..........................................................................................................................3 2 APPLICABLE STANDARDS ...............................................................................................3 3 CATALOG NO. STRUCTURE .........................................................................................3 4 CONNECTOR SHAPE, DIMENSIONS AND MARTERIALS 5 ACCOMMODATED CONDUCTORS (FPC/FFC) .......................................................................3 6 PACKAGING CONDITION ........................................................ ...........................................3 7 RECOMMENDED MOUNTING PATTERN DIMENSIONS 8 RATING 9 .....................................................3 ........................................................3 .......................................................................................................................4 8-1 Voltage ..................................................................................................................4 8-2 Current ....................................................................................................................4 8-3 Operating Temperature ..............................................................................................4 PERFORMANCE CHARACTERISTICS ...............................................................................4 9-1 Electrical Performance ...............................................................................................4 9-1-1 Contact resistance ............................................................................................4 9-1-2 Insulation resistance ...........................................................................................5 9-1-3 Dielectric withstanding voltage ...........................................................................5 9-2 Mechanical Performance .............................................................................................5 9-2-1 Durability (Slider operation) ...............................................................................5 9-2-2 Vibration (Sinusoidal) ........................................................................................5 Copyright FCI Form E-3334 Rev F GS-01-001 NUMBER TYPE PRODUCT SPECIFICATION 110-435G TITLE PAGE 0.5mm Pitch FPC/FFC Connector 62674-_ _ 11_1ALF REVISION 2 of 10 AUTHORIZED BY Sei Watanabe B DATE 2010-5-19 CLASSIFICATION UNRESTRICTED 9-3 Environmental Performance .......................................................................................6 9-3-1 Damp heat (Steady state) ...................................................................................6 9-3-2 Salt spray ........................................................................................................6 9-3-3 Change of temperature 9-4 Other performance ......................................................................................7 ......................................................................................................7 9-4-1 Soldering (Resistance to reflow soldering) ...............................................................7 9-4-2 Soldering (Solderability) (Reflow) ............................................................................8 10 INDICATION AND PACKAGING ........................................................................................9 10-1 Indication ...........................................................................................................9 10-2 Packaging .........................................................................................................9 11 REMARKS ......................................................................................................................9 12 RECOMMENDED REFLOW PROFILE .................................................................................9 13 REVISION RECORD ...................................................................................................10 Copyright FCI Form E-3334 Rev F GS-01-001 NUMBER TYPE 110-435G PRODUCT SPECIFICATION TITLE PAGE REVISION 3 of 10 0.5mm Pitch FPC/FFC Connector 62674-_ _ 11_1ALF AUTHORIZED BY Sei Watanabe B DATE 2010-5-19 CLASSIFICATION UNRESTRICTED 1. SCOPE This specification covers the requirements for the connector with 0.5mm spacing to which the edge of FPC(Flexible Printed Circuit) and FFC(Flexible Flat Cable) can be connected by Zero-Insertion-Force method and which copes with automatic mounting and SMT. 2. APPLICABLE STANDARDS JIS C 5402 Method for Test of Connectors for Electronic Equipment JIS C 0806 Packing of Electronic Components on Continuous Tapes (Surface Mount Components) UL - 94 TESTS FOR FLAMMABILITY OF PLASTIC MATERIALS FOR PARTS IN DEVICES AND APPLIANCES. 3. CATALOG No. STRUCTURE 62674 - 20 1 1 2 1 A LF Series Number of Contacts Contact direction SMT Variation 2 : Foot Pattern A Packaging 0 : Connector 1 : Plastic Tape Packaging Gold Plating Lead Free 4. CONNECTOR SHAPE, DIMENSIONS AND MATERIALS See attached drawings. 5. ACCOMMODATED CONDUCTORS (FPC/FFC) See attached drawings. 6. PACKAGING CONDITION See attached drawings. 7. RECOMMENDED MOUNTING PATTERN DIMENSIONS See attached drawings. Copyright FCI Form E-3334 Rev F GS-01-001 NUMBER TYPE PRODUCT SPECIFICATION 110-435G TITLE PAGE REVISION 4 of 10 0.5mm Pitch FPC/FFC Connector 62674-_ _ 11_1ALF B AUTHORIZED BY DATE Sei Watanabe 2010-5-19 CLASSIFICATION UNRESTRICTED 8. RATING 8-1. Voltage : A.C.50V D.C.50V 8-2. Current : A.C.0.5A D.C.0.5A (Refer to the following note.) 8-3. Operating Temperature : -55C ~ +105C (Including terminal temperature rises) NOTE Allowable maximum current for one contact is 0.5A. Total allowable current for a whole connector is the value which is shown in the following figure. 4 3 Total Current 2 (A) 1 0 2 4 6 8 10 12 14 16 18 20 22 24 26 Number of contacts 9. PERFORMANCE CHARACTERISTICS 9-1. Electrical Performance No. Test Item Test Method 1)Measure contact resistance between V1-V2 by voltage drop method by the following circuit by mating accommodated conductor specified in clause 5 after reflow soldering the connector on the P.CB. Conductor 28 30 32 34 36 38 40 Requirements 1)Initial value : Less than 30m 2)Contact resistance after the test is in accordance with the value specified in each test item. Soldering portion Connector 9-1-1 Pattern Contact resistance P.C.B. 2)Open circuit voltage : Less than A.C.20mV 3)Test current : Less than A.C.20mA Copyright FCI Form E-3334 Rev F GS-01-001 NUMBER TYPE 110-435G PRODUCT SPECIFICATION TITLE PAGE 0.5mm Pitch FPC/FFC Connector 62674-_ _ 11_1ALF REVISION 5 of 10 AUTHORIZED BY B DATE Sei Watanabe 2010-5-19 CLASSIFICATION UNRESTRICTED 9-1-2 Insulation resistance 9-1-3 Dielectric withstanding voltage 9-2. Mechanical Performance No. Test Item 9-2-1 Durability (Slider operation) 9-2-2 Vibration (Sinusoidal) 1)Measure insulation resistance between adjacent contacts in a connector individual. 2)Test voltage : D.C.500V 3)Read value one minute after applying test voltage. 1)For one minute, apply A.C.200V between adjacent contacts in a connector individual. 2)Set current : A.C.1mA 1)More than 100M Test Method 1)Measure contact resistance before and after the test by the method in clause 9-1-1 by mating the accommodated conductor specified in clause 5. 2) Number of slider open and close : 20 times (Insert and extract the conductor for each opening of the slider.) JIS C 60068-2-6 (IEC60068-2-6) 1) Frequency range : 10 ~ 500Hz 2)Amplitude : 0.75mm or Acceleration : 100m/s2 3)Sweep rate : 1 octave/minute 4)Kind of test : Sweep endurance test 5)Test time : 10 cycles Requirements 1)Initial contact resistance : Less than 30m 2)Contact resistance after the test : Less than 50m 3)Free from any defect such as break etc. on the connector and conductor. 1)During the test, no circuit opening for more than 1s. 2)Free from any defect such as break, deformation, loosing and falling off etc. on each portion of the connector. 1)Free from any short circuit and insulation breakdown. Copyright FCI Form E-3334 Rev F GS-01-001 NUMBER TYPE 110-435G PRODUCT SPECIFICATION TITLE PAGE 0.5mm Pitch FPC/FFC Connector 62674-_ _ 11_1ALF REVISION 6 of 10 AUTHORIZED BY B DATE Sei Watanabe 2010-5-19 CLASSIFICATION UNRESTRICTED 9-3. Environmental Performance No. Test Item Test Method JIS C 60068-2-78 (IEC60068-2-78) 1) Measure contact resistance before and after the test by the method in clause 9-1-1 by using the accommodated conductor specified in clause 5. 2) Measure insulation resistance after the test by the method in clause 9-1-2. Damp heat 9-3-1 (Steady state) 3) Bath temperature : 40C 4) Bath humidity : 90 ~ 95%(relative humidity) 5) Period of exposure : 48 hours 6) Expose conductor and connector in mated condition and leave them under normal temperature. (Without insertion and separation) JIS C 60068-2-11 (IEC60068-2-11) 1)Measure contact resistance before and after the test according to the method in clause 9-1-1 by using accommodated conductor specified in clause 5. 9-3-2 Salt spray 2) Salt solution concentration : 5% 3) Period of exposure : 48 hours 4) Expose conductor and connector in mated condition and leave them under normal temperature after posttreatment. (24 hours) Requirements 1) Initial contact resistance : Less than 30m 2) Contact resistance after the test : Less than 50m 3) Insulation resistance after the test : More than 100M 1) Initial contact resistance : Less than 30m 2) Contact resistance after the test : Less than 50m Copyright FCI Form E-3334 Rev F GS-01-001 NUMBER TYPE PRODUCT SPECIFICATION 110-435G TITLE PAGE REVISION 7 of 10 0.5mm Pitch FPC/FFC Connector 62674-_ _ 11_1ALF AUTHORIZED BY Sei Watanabe B DATE 2010-5-19 CLASSIFICATION UNRESTRICTED 9-3-3 Change of temperature JIS C 0025 (IEC60068-2-14) 1) Measure contact resistance before and after the test according to the method in clause 9-1-1 by using accommodated conductor specified in clause 5. 2) One cycle of temperature is as follow and test 5 cycles. Step Temp.(C) Time(min.) 1 2 3 4 -553 252 852 252 30 2~3 30 2~3 1) Initial contact resistance : Less than 30m 2) Contact resistance after the test : Less than 50m 3) Free from any defect such as crack, warping and deformation etc. on each portion the connector. 3) Expose conductor and connector in mated condition and leave them under normal temperature. 9-4. Other performance No. Test Item 9-4-1 Soldering (Resistance to reflow soldering) Test Method JIS C 60068-2-58 (IEC60068-2-58) 1)Solder by setting reflow bath on the following condition. 2) Preheating150~180C, 1205 s 3) Soldering 220C min. 60s max. 4) Peak 245C min. 20s max. (Peak 255C max.) NOTE Temperature must be measured at contact terminal portion and peak temperature on the upper surface of P.C.B must be less than 260C. 5) Solder paste to be used is JIS Z 3282 Sn96.5Ag3.0Cu0.5 Requirements 1)Contact resistance after the test : Less than 50m 2)Insulation resistance after the test : More than 100M 3)No short circuit and insulation breakdown for dielectric withstanding voltage test after this test. 4)Free from any damage on performance and contact performance after soldering. Diagram A Copyright FCI Form E-3334 Rev F GS-01-001 NUMBER TYPE 110-435G PRODUCT SPECIFICATION TITLE PAGE 0.5mm Pitch FPC/FFC Connector 62674-_ _ 11_1ALF REVISION 8 of 10 AUTHORIZED BY Sei Watanabe B DATE 2010-5-19 CLASSIFICATION UNRESTRICTED 9-4-2 Soldering (Solderability) (Reflow) JIS C 60068-2-58 (IEC60068-2-58) 1) Solder by setting reflow bath on the following condition. 2) Preheating150~180C, 60~120s 3) Soldering 225C min., 205s (Peak 235C max.) NOTE Temperature must be measured at contact terminal portion and peak temperature on the upper surface of P.C.B must be less than 260C. 4) Solder paste to be used is JIS Z 3282 Sn96.5Ag3.0Cu0.5 1) Actual soldered area must be more than 90% of the dipped area intended to be soldered. Diagram B Copyright FCI Form E-3334 Rev F GS-01-001 NUMBER TYPE 110-435G PRODUCT SPECIFICATION TITLE PAGE 0.5mm Pitch FPC/FFC Connector 62674-_ _ 11_1ALF REVISION 9 of 10 AUTHORIZED BY Sei Watanabe B DATE 2010-5-19 CLASSIFICATION UNRESTRICTED 10.INDICATION AND PACKAGING 10-1. Indication 1) Catalog number and lot number are not be indicated on the connector. 2) Catalog number and quantity shall be indicated on the surface of the package box. 10-2. Packaging 1) The connector individuals are packed by tapes with specified quantity in accordance with [JIS C 0806 "Packaging of Electronic Components on Continuous Tapes (Surface Mount components)" ] and put into package box in accordance with FCI JAPAN packaging specification. 11.REMARKS 11-1. Please use for gold plating cable as accommodated conductor. 12. RECOMMENDED REFLOW PROFILE Diagram C. Recommended reflow temperature profile Note: Please check the reflow soldering condition for your own application beforehand due to different conditions with soldering devices, P.C. Boards, etc. No moisture treatment before reflow process. Copyright FCI Form E-3334 Rev F GS-01-001 NUMBER TYPE 110-435G PRODUCT SPECIFICATION TITLE PAGE 0.5mm Pitch FPC/FFC Connector 62674-_ _ 11_1ALF REVISION 10 of 10 AUTHORIZED BY Sei Watanabe B DATE 2010-5-19 CLASSIFICATION UNRESTRICTED 13. REVISION RECORD REV. PAGE DESCRIPTION ECR# DATE A ALL ALL J05-0353 ECR-EXL-J -003824 2005-6-15 B RELEASE Form Change Operating temperature to -55 ~ 105C 2010-5-19 Copyright FCI Form E-3334 Rev F GS-01-001 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: FCI: 62674-081121ALF 62674-161121ALF 62674-121121ALF 62674-331121ALF 62674-261121ALF 62674-201121ALF 62674-241121ALF 62674-301121ALF 62674-251121ALF 62674-211121ALF 62674-321121ALF