(R) (R) Cree XLamp XT-E LEDs Product Description FEATURES Table of contents XLamp(R) XT-E is Cree's highest * Available in white, 80-CRI min white, 70-CRI min white and royal blue Characteristics........................... 2 performing silicon carbide-based LED technology, Cree's delivered industry-standard in XP/XT Flux Characteristics..................... 3 Relative Spectral Power Distribution ............................... 5 packaging. XT-E White sets the * New: available in 2200 K CCT Relative Luminous Flux vs. new standard for high performance * Binned at 85 C Junction Temperature.................. 6 and dramatically lowers system * Cool white efficacy of up to 148 lm/W (@ 85 C, 350 mA) Electrical Characteristics.............. 7 highest performing source of royal * Royal Blue wall plug efficiency of up to 53% (@ 85 C, 350 mA) Current..................................... 7 blue * Wide viewing angle: 115-140 Relative Chromaticity vs. Current * Thermal resistance: 5 C/W and Temperature........................ 9 * Maximum drive current: 1.5 A Typical Spatial Distribution..........10 cost. XT-E Royal Blue is Cree's light for remote-phosphor applications. Cree XLamp performance LEDs bring and quality high of light to a wide range of lighting applications, including remote- phosphor, color-changing, portable and personal, outdoor, indoor- directional, transportation, stage and studio, commercial emergency-vehicle lighting. WWW.CREE.COM/XLAMP * Warm white available in 85- and 90-CRI min. and Relative Luminous Flux vs. * Electrically neutral thermal path Thermal Design.........................11 * Vf binning supported for XT-E White and Royal Blue Reflow Soldering Characteristics..12 * XT-E Royal Blue sorted into 2.5nm wavelength bins Mechanical Dimensions..............14 * Unlimited floor life at 30 C/85% RH CLD-DS41 Rev 10B Product family data sheet Notes.......................................13 Tape and Reel...........................15 Packaging.................................16 * Reflow solderable - JEDEC JSTD020C compatible * RoHS- and REAChcompliant * ULrecognized component (E349212) NOTE: For remote phosphor applications, a separate license to certain Cree patents is required. Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Copyright (c) 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree,(R) the Cree logo and XLamp are registered trademarks of Cree, Inc. Cree , the Cree logo and XLamp(R) are registered trademarks of Cree, Inc. Cree, Inc. Cree,Drive Inc. 4600 Silicon 4600 Silicon Drive Durham, NC 27703 NC 27703 USA Tel:Durham, +1.919.313.5300 USA Tel: +1.919.313.5300 www.cree.com/xlamp xlamp XT-E LEDs Characteristics Characteristics Unit Thermal resistance, junction to solder point C/W 5 Viewing angle (FWHM) - white degrees 115 Viewing angle (FWHM) - royal blue degrees 140 Temperature coefficient of voltage mV/C -2.5 ESD withstand voltage (HBM per Mil-Std-883D) Minimum Typical Maximum V 8000 mA 1500 Reverse voltage V 5 Forward voltage (@ 350 mA, 85 C) V LED junction temperature C DC forward current 2.85 3.4 150 Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered of Cree, Inc. trademarks of Cree, Inc. 2 xlamp XT-E LEDs Flux Characteristics - White (TJ = 85 C) The following table provides several base order codes for XLamp XT-E White LEDs. It is important to note that the base order codes listed here are a subset of the total available order codes for the product family. For more order codes, as well as a complete description of the order-code nomenclature, please consult the XLamp XT-E Binning and Labeling document. CCT Range Color Cool White Outdoor White Neutral White Warm White 70 CRI Minimum Neutral White 80 CRI Minimum White 85-CRI Minimum Warm White 90-CRI Minimum Warm White Min. Max. 5000 K 8300 K 4000 K 3700 K 2200 K 2600 K 2200 K 2600 K 2600 K 6200 K 5000 K 3700 K 8300 K 6200 K 3700 K 3700 K Base Order Codes Minimum Luminous Flux @ 350 mA Calculated Minimum Luminous Flux (lm)** @ 85 C Order Code Group Flux (lm) @ 85 C Flux (lm) @ 25 C* 700 mA 1500 mA R3 122 140 217 376 XTEAWT-00-0000-000000F51 R4 130 149 231 401 XTEAWT-00-0000-000000G51 XTEAWT-00-0000-000000H51 R5 139 160 247 428 R3 122 140 217 376 XTEAWT-00-0000-000000FE3 R4 130 149 231 401 XTEAWT-00-0000-000000GE3 R5 139 160 247 428 XTEAWT-00-0000-000000HE3 R2 114 131 203 351 XTEAWT-00-0000-000000EF4 R3 122 140 217 376 XTEAWT-00-0000-000000FF4 XTEAWT-00-0000-000000GF4 R4 130 149 231 401 Q3 93.9 108 167 289 XTEAWT-00-0000-00000LBE7 Q4 100 115 178 308 XTEAWT-00-0000-00000LCE7 Q5 107 123 191 330 XTEAWT-00-0000-00000LDE7 Q4 100 115 178 308 XTEAWT-00-0000-00000BCE7 Q5 107 123 191 330 XTEAWT-00-0000-00000BDF6 R2 114 131 203 351 XTEAWT-00-0000-00000BEF5 R3 122 140 217 376 XTEAWT-00-0000-00000BFC3 R4 130 149 231 401 XTEAWT-00-0000-00000BG53 Q3 93.9 108 167 289 XTEAWT-00-0000-00000HBE7 Q4 100 115 178 308 XTEAWT-00-0000-00000HCE6 Q5 107 123 191 330 XTEAWT-00-0000-00000HDE5 R2 114 131 203 351 XTEAWT-00-0000-00000HEF4 R3 122 140 217 376 XTEAWT-00-0000-00000HF50 P3 73.9 85 132 228 XTEAWT-00-0000-00000P8E7 P4 80.6 93 144 248 XTEAWT-00-0000-00000P9E7 Q2 87.4 100 156 269 XTEAWT-00-0000-00000PAE7 P3 73.9 85 132 228 XTEAWT-00-0000-00000U8E7 P4 80.6 93 144 248 XTEAWT-00-0000-00000U9E7 Q2 87.4 100 156 269 XTEAWT-00-0000-00000UAE7 Notes: * Cree maintains a tolerance of 7% on flux and power measurements, 0.005 on chromaticity (CCx, CCy) measurements and 2 on CRI measurements. * Typical CRI for Neutral White, 3,700 K - 5,000K CCT is 75. * Typical CRI for Warm White, 2,200 K - 3,700 K CCT is 80. * Flux values @ 25 C are calculated and for reference only. ** Calculated flux values at 700 mA and 1500 mA are for reference only. Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered of Cree, Inc. trademarks of Cree, Inc. 3 xlamp XT-E LEDs Flux Characteristics - Royal Blue (TJ = 85 C) The following table provides order codes for XLamp XT-E Royal Blue LEDs. Additional information on the performance grouping and codes for XT-E Royal Blue LEDs can be found in the XT-E Binning and Labeling document. Dominant Wavelength Range DWL Kit Codes Min. Max. Order Codes, Minimum Radiant Flux @ 350 mA, Tj=85 C Group DWL (nm) Group DWL (nm) 500 mW - Radiant Flux Group Code 32 (L) 525 mW - Radiant Flux Group Code 33 (M) 550 mW - Radiant Flux Group Code 34 (N) 01 D36 450 D57 465 XTEARY-00-0000-000000L01 XTEARY-00-0000-000000M01 XTEARY-00-0000-000000N01 02 D36 450 D47 460 XTEARY-00-0000-000000L02 XTEARY-00-0000-000000M02 XTEARY-00-0000-000000N02 03 D46 455 D57 465 XTEARY-00-0000-000000L03 XTEARY-00-0000-000000M03 XTEARY-00-0000-000000N03 04 D36 450 D37 455 XTEARY-00-0000-000000L04 XTEARY-00-0000-000000M04 XTEARY-00-0000-000000N04 05 D46 455 D47 460 XTEARY-00-0000-000000L05 XTEARY-00-0000-000000M05 XTEARY-00-0000-000000N05 06 D56 460 D57 465 XTEARY-00-0000-000000L06 XTEARY-00-0000-000000M06 XTEARY-00-0000-000000N06 07 D37 452.5 D46 457.5 XTEARY-00-0000-000000L07 XTEARY-00-0000-000000M07 XTEARY-00-0000-000000N07 08 D47 457.5 D56 462.5 XTEARY-00-0000-000000L08 XTEARY-00-0000-000000M08 XTEARY-00-0000-000000N08 09 D37 452.5 D56 462.5 XTEARY-00-0000-000000L09 XTEARY-00-0000-000000M09 XTEARY-00-0000-000000N09 Dominant Wavelength Range DWL Kit Codes Min. Max. Order Codes, Minimum Radiant Flux @ 350 mA, Tj=85 C Group DWL (nm) Group DWL (nm) 575 mW - Radiant Flux Group Code 35 (P) 600 mW - Radiant Flux Group Code 36 (Q) 01 D36 450 D57 465 XTEARY-00-0000-000000P01 XTEARY-00-0000-000000Q01 02 D36 450 D47 460 XTEARY-00-0000-000000P02 XTEARY-00-0000-000000Q02 03 D46 455 D57 465 XTEARY-00-0000-000000P03 04 D36 450 D37 455 XTEARY-00-0000-000000P04 05 D46 455 D47 460 XTEARY-00-0000-000000P05 06 D56 460 D57 465 07 D37 452.5 D46 457.5 08 D47 457.5 D56 462.5 09 D37 452.5 D56 462.5 XTEARY-00-0000-000000Q04 XTEARY-00-0000-000000P07 XTEARY-00-0000-000000P09 Note: * Cree maintains a tolerance of 7% on flux and power measurements, 0.005 on chromaticity (CCx, CCy) measurements, 2 on CRI measurements and 1 nm on dominant wavelength measurements. Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered of Cree, Inc. trademarks of Cree, Inc. 4 xlamp XT-E LEDs Relative Spectral Power Relative Spectral Power Distribution - White Relative Radiant Power (%) 100 80 60 5000K - 8300K CCT 2600K - 3700K CCT 2200K CCT 40 20 0 400 450 500 550 600 650 700 750 Wavelength (nm) Relative sPECTRAL pOWER dISTRIBUTION - Royal Blue Relative Spectral Power Relative Radiant Power (%) 100% 80% 60% Royal Blue 40% 20% 0% 400 450 500 550 600 650 700 750 Wavelength (nm) Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered of Cree, Inc. trademarks of Cree, Inc. 5 xlamp XT-E LEDs Relative Flux Output vs. Junction Temperature Relative Luminous Flux vs. Junction Temperature (IF = 350 mA) - White Relative Luminous Flux 120% 100% 80% 60% 40% 20% 0% 25 50 75 100 125 150 Junction Temperature (C) Relative Flux Output vs. Junction Temperature Relative Radiant Flux vs. Junction Temperature (IF = 350 mA) - Royal Blue Relative Radiant Flux 120% 100% 80% 60% 40% 20% 0% 25 50 75 100 125 150 Junction Temperature (C) Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered of Cree, Inc. trademarks of Cree, Inc. 6 xlamp XT-E LEDs Electrical Characteristics (Tj = 85C) Electrical Characteristics (TJ = 85 C) 1600 Forward Current (mA) 1400 1200 1000 800 600 400 200 0 2.50 2.75 3.00 3.25 3.50 Forward Voltage (V) Relative Intensity vs. Current (Tj = 85C) Relative Luminous Flux vs. Current (TJ = 85 C) - White Relative Luminous Flux (%) 350% 300% 250% 200% 150% 100% 50% 0% 0 200 400 600 800 1000 1200 1400 1600 Forward Current (mA) Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered of Cree, Inc. trademarks of Cree, Inc. 7 Relative Radiant Flux vs. Current (Tj = 85C) xlamp XT-E LEDs Relative Radiant Flux vs. Current (TJ = 85 C) - Royal Blue Relative Radiant Flux (%) 350% 300% 250% 200% 150% 100% 50% 0% 0 200 400 600 800 1000 Forward Current (mA) 1200 1400 1600 Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered of Cree, Inc. trademarks of Cree, Inc. 8 xlamp XT-E LEDs Relative Chromaticity Vs. Current, WW Relative Chromaticity vs. Current and Temperature (Warm White) 0.020 T = 85 C J 0.015 0.010 0.005 0.000 CCx CCy -0.005 -0.010 -0.015 -0.020 0 200 400 600 800 1000 Current (mA) 1200 1400 1600 Relative Chromaticity Vs. Temperature WW 0.020 I = 350 mA F 0.015 0.010 0.005 0.000 CCx CCy -0.005 -0.010 -0.015 -0.020 0 20 40 60 80 Tsp (C) 100 120 140 160 Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered of Cree, Inc. trademarks of Cree, Inc. 9 xlamp XT-E LEDs Typical Spatial Radiation Pattern Typical Spatial Distribution - White Relative Luminous Intensity (%) 120 100 80 60 40 20 0 -90 -70 -50 -30 -10 10 30 50 70 90 Angle () pical Spatial Distribution Typical Spatial Distribution - Royal Blue Relative Luminous Intensity (%) 120 100 80 60 40 20 0 -90 -70 -50 -30 -10 10 30 50 70 90 Angle () Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered of Cree, Inc. trademarks of Cree, Inc. 10 xlamp XT-E LEDs Thermal Design The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is Thermal Design crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life and optical characteristics. 1600 Maximum Current (mA) 1400 1200 1000 800 Rj-a Rj-a Rj-a Rj-a 600 400 = = = = 10C/W 15C/W 20C/W 25C/W 200 0 0 20 40 60 80 100 120 140 Ambient Temperature (C) Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered of Cree, Inc. trademarks of Cree, Inc. 11 xlamp XT-E LEDs Reflow Soldering Characteristics In testing, Cree has found XLamp XT-E LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of solder paste used. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment. tP TP Critical Zone TL to TP Temperature Ramp-up TL tS Tsmax Tsmin Ramp-down ts Preheat 25 Profile Feature t 25C to Peak Time Lead-Based Solder Lead-Free Solder 3 C/second max. 3 C/second max. Preheat: Temperature Min (Tsmin) 100 C 150 C Preheat: Temperature Max (Tsmax) 150 C 200 C 60-120 seconds 60-180 seconds 183 C 217 C 60-150 seconds 60-150 seconds 215 C 260 C 10-30 seconds 20-40 seconds 6 C/second max. 6 C/second max. 6 minutes max. 8 minutes max. Average Ramp-Up Rate (Tsmax to Tp) Preheat: Time (tsmin to tsmax) Time Maintained Above: Temperature (TL) Time Maintained Above: Time (tL) Peak/Classification Temperature (Tp) Time Within 5 C of Actual Peak Temperature (tp) Ramp-Down Rate Time 25 C to Peak Temperature Note: All temperatures refer to the topside of the package, measured on the package body surface. Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered of Cree, Inc. trademarks of Cree, Inc. 12 xlamp XT-E LEDs Notes Lumen Maintenance Projections Cree now uses standardized IES LM-80-08 and TM-21-11 methods for collecting long-term data and extrapolating LED lumen maintenance. For information on the specific LM-80 data sets available for this LED, refer to the public LM-80 results document at www.cree.com/xlamp_app_notes/LM80_results. Please read the XLamp Long-Term Lumen Maintenance application note at www.cree.com/xlamp_app_notes/lumen_ maintenance for more details on Cree's lumen maintenance testing and forecasting. Please read the XLamp Thermal Management application note at www.cree.com/xlamp_app_notes/thermal_management for details on how thermal design, ambient temperature, and drive current affect the LED junction temperature. Moisture Sensitivity In testing, Cree has found XLamp XT-E LEDs to have unlimited floor life in conditions 30 C/85% relative humidity (RH). Moisture testing included a 168hour soak at 85 C/85% RH followed by 3 reflow cycles, with visual and electrical inspections at each stage. Cree recommends keeping XLamp LEDs in their sealed moisture-barrier packaging until immediately prior to use. Cree also recommends returning any unused LEDs to the resealable moisture-barrier bag and closing the bag immediately fter use. RoHS Compliance The levels of RoHS restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2011/65/EC (RoHS2), as implemented January 2, 2013. RoHS Declarations for this product can be obtained from your Cree representative or from the Product Ecology section of www.cree.com. REACh Compliance REACh substances of high concern (SVHCs) information is available for this product. Since the European Chemical Agency (ECHA) has published notices of their intent to frequently revise the SVHC listing for the foreseeable future, please contact a Cree representative to insure you get the most up-to-date REACh Declaration. Historical REACh banned substance information (substances restricted or banned in the EU prior to 2010) is also available upon request. UL Recognized Component Level 4 enclosure consideration. The LED package or a portion thereof has been investigated as a fire and electrical enclosure per ANSI/UL 8750. Vision Advisory Claim WARNING: Do not look at an exposed lamp in operation. Eye injury can result. See LED Eye Safety at www.cree.com/ xlamp_app_notes/led_eye_safety. Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered of Cree, Inc. trademarks of Cree, Inc. 13 3.30 xlamp XT-E LEDs .65 .650 1.30 R1.530 Mechanical Dimensions 1.15 All measurements are .13 mm unless otherwise indicated. 6 5 6 6 .60 5 4 5 4 3 4 3 NOTICE NOTICE NOTICE 1.20 CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CREE CONFIDENTIAL. THIS PLOT AND INFORMATION CREE CONFIDENTIAL. THIS PLOT AND THETHE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND CONTAINED WITHIN ARE PROPRIETARY .60 ANDAND CONTAINED WITHIN ARE THETHE PROPRIETARY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONFIDENTIAL INFORMATION OF CREE, MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY INC. THIS PLOT MAY NOT BETHE COPIED, REPRODUCED DISCLOSED ANY MAY NOT BE COPIED, REPRODUCED OR OR DISCLOSED TO TO ANY UNAUTHORIZED PERSON WITHOUT WRITTEN CONSENT UNAUTHORIZED PERSON WITHOUT WRITTEN CONSENT OF CREE INC. UNAUTHORIZED PERSON WITHOUT THETHE WRITTEN CONSENT B 2 3 REVISONS REV DESCRIPTIONREV REV B REMOVED CHIP DIMENSIONS B B R CREE OF OF CREE INC.INC. 3.30 D D 3.20 .40 1.65 D ANODE 1.60 .40 .40 1.30 3.20 3.450 3.30 2.36UNLESS OTHERWISE SPECIFIED 3.450 3.450 DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX .25 .XXX .125 X .5 RECOMMENDED STENCIL PATTERN (HATCHED AREA IS OPENING) MENDED PCB SOLDER PAD .83 THIRD ANGLE PROJECTION D. CRONIN 3/8/11 FOR SHEET METAL PARTS ONLY .X 1.5 .XX .75 .XXX .25 X .5 CHECK 4 -- APPROVED -MATERIAL DATE TITLE -- .83.83 SIZE FINAL PROTECTIVE FINISH 3 Phone (919) 313-5300 Fax (919) 313-5558 1.15 2.30 A 2.30 1.15 OUTLINE DRAWING XP HEW 1.15 .50 -- 4600 Silicon Drive Durham, N.C 27703 2.30 DATE -- SURFACE FINISH: 1.6 5 DATE DRAWN BY 2.36 2.36 -- SCALE C REV. DRAWING NO. 2610-00015 .50.50 B SHEET 24.000 2 OF 1 /1 1 C 3.450 C C 3.30 3.450 3.450 ANODE .65 .650 1.30 R1.530 Top View R1.530 .65 B .60 .65.65 B B .60.60 1.20 1.20 .50.50 .60.60 .50 3.30 3.20 .40 1.65 .50.50 .50 3.20 3.20 .40 .40 .40.40 1.65 1.65 1.30 .40.40 .40 .403.30 .50.50 RECOMMENDED STENCIL PATTERN .40.40 (HATCHED AREA IS OPENING) 3.20 3.20 3.30 3.30 5 Recommended PCB Solder Pad 4 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX .25 .XXX .125 X .5 DRAWN BY D. CRONIN CHECK DATE 3/8/11 DATE -APPROVED -- -DATE -- TITLE DRAWN OUTLINE D DRAWN BY UNLESS OTHERWISE SPECIFIED UNLESS OTHERWISE SPECIFIED D. C D. CRON DIMENSIONS DIMENSIONS ARE ARE IN IN CHECK MILLIMETERS AND AFTER FINISH. CHECK MILLIMETERS AFTERSIZE FINISH. DRAWING -- ANDUNLESS RECOMMENDED STENCIL PATTERN RECOMMENDED STENCIL PATTERN TOLERANCE SPECIFIED: -TOLERANCE UNLESS SPECIFIED: FINAL PROTECTIVE FINISH .25 .25 (HATCHED AREA IS OPENING) APPROV .XX .XX (HATCHED AREA IS OPENING) APPROVED .125 .125 .XXX.XXX SCALE 1.6 -SURFACE FINISH: -- X X .5 .5 24.000 THIRD ANGLE PROJECTION THIRD ANGLE PROJECTION MATERI MATERIAL METAL PARTS 3 2 SHEET FOR FOR SHEET METAL PARTS ONLYONLY 1.5 1.5 .X .X .75 .75 .XX .XX .25 .25 FINAL PRO .XXX.XXX FINAL PROTECTI .5 .5 X X THIRD ANGLE PROJECTION RECOMMENDED PCB SOLDER PAD RECOMMENDED PCB SOLDER PAD 6 1.60 1.60 3.20 1.30 RECOMMENDED PCB SOLDER 1.30 PAD A A 1.60 3.30 3.30 .40 A 1.30 1.30 .60 1.20 1.15 1.15 .50 Bottom View Side View R1.530 1.15 .65.65 .650 .650 FOR SHEET METAL PARTS ONLY .X 1.5 .XX .75 .XXX .25 X .5 MATERIAL C Recommended Stencil Pattern (Shaded Area Is Open) 1.6 1.6 SURFACE FINISH: SURFACE FINISH: 6 6 5 5 4 4 3 3 Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered of Cree, Inc. trademarks of Cree, Inc. 14 REF REF 4.375 4.375 F(III) Bo xlamp XT-E LEDs Bo X X Y D1 1.5 MIN. SECTION Y-Y Tape and Reel RE R0.2 TYPICAL Ko REF R0.2 TYPICAL Y Ko All Cree carrier tapes conform to EIA-481D, Automated Component Handling Systems Standard. P1 Ao D1 All dimensions in mm. 1.5 MIN. SECTION Y-Y REF 0.59 R 4 2.2 1.5 5 Do P2 2.0 0.05 (I) 0. 0 Po 4.0 0.1 (II) CATHODE SIDE Y 5 E1 1.75 0.1 T 0.30 0.05 F(III) SECTION X-X REF 4.375 X X 6 Ao 3.70 Bo Ko F 3.70 D1 2.40 1.5 MIN. 5.50 8.00 12.00 +/0.1 5 REV Ao +/- 0.1 +0.3/-0.1 Measured from centerline of sprocket hole to centerline of pocket. 2 Cumulative tolerance of 10 sprocket REVISONS holes is 0.20. BY DESCRIPTION ADDED CATHODE AND ANODE NOTE of sprocket Measured from centerline DC REORIENTED DEVICE hole to centerline of pocket. Other material available. (III) B REF 0.59 4 D P1 2.2 P1 W +/- 0.1 +0.0/-0.1 +/- 0.05 (II) 3 ANODE SIDE R SECTION Y-Y 4 +/- 0.1 +0.0/-0.1 +/- 0.05 Y +/- 0.1 3.70 2.40 5.50 8.00 12.00 (I) REF R0.2 TYPICAL Ko NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUTTHE WRITTEN CONSENT OF CREE INC. 3.70 Bo Ko F P1 W W Bo Ao (IV) 1 DATE APP' 2/26/12 +/- 0.1 +0.3/-0.1 SECTION X-X 1.5 .1 User Feed Direction (I) Ao 3.70 8.1 +/- 0.1END 3.70 +/- 0.1 2.40 +0.0/-0.1 6 +/- 0.05 NOTICE5.50 CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED ARE THE PROPRIETARY 8.00 AND P 1WITHIN +/- 0.1 CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY W PERSON WITHOUT 12.00 +0.3/-0.1 UNAUTHORIZED THE WRITTEN CONSENT Bo Ko F 5 4.1 Measured from centerline of sprocket hole to centerline of pocket. holes is 0.20. (III) Measured from centerline of sprocket hole to centerline of pocket. 3 OE Foxit PDF Editor a1/4aeEEuO (c) by Foxit Software Company, 2004 (IV) Other material available. 4 2.5.1 1.75 .10 CATHODE(II)SIDE Cumulative tolerance ofSTART 10 sprocket 12.0 +.3 -.0 2 1/2oOAOUAEAA OF CREE, INC. 1 ANODE SIDE Trailer 160mm (min) of empty pockets sealed with tape (20 pockets min.) D 6 NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT 190 OF CREE, INC. Leader 400mm (min.) of empty pockets with at least 100mm sealed by tape (50 empty pockets min.) Loaded Pockets (1000 Lamps) 5 4 D 3 2 OE Foxit PDF Editor a1/4aeEEuO (c) by Foxit Software Company, 2004 1/2oOAOUAEAA 1 16.40 User Feed Direction D B D C Carrier Tape C 16.40 Pocket Tape 190 61 +/-0.5 13mm OD 7" A 7.5 C +2.00 12.40 0 MEASURED AT HUB '' C THIRD ANGLE PROJECTION B UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX .25 .XXX .125 X .5 FOR SHEET METAL PARTS ONLY .X 1.5 .XX .75 .XXX .25 61 +/-0.5 X .5 13 SURFACE FINISH: 6 5 4 OD 7.5 '' D. CRONIN CHECK 4600 Silicon Drive Durham, N.C 27703 11/29/10 DATE -- Phone (919) 313-5300 -- -- TITLE -- XP HEW LOADING SPEC MATERIAL -- SIZE C FINAL PROTECTIVE FINISH -- 1.6 Fax (919) 313-5558 B DATE APPROVED 3 12.40 DATE DRAWN BY SCALE 2402-00014 SHEET 3.000 2 1 MEASURED AT INSIDE EDGE +2.00 12.40 0 MEASURED AT HUB B B UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS & BEFORE FINISH. TOLERANCE UNLESS SPECIFIED: .X 0.3 .XX .13 DRAWN BY DATE A Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks 13 Copyright (c) 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered of Cree, Inc. A trademarks of Cree, Inc. THIRD ANGLE PROJECTION 12.40 MEASURED AT INSIDE EDGE X 1 FOR SHEET METAL PARTS ONLY .X .25 .XX .10 X 2 LIUDEZHI 2012/5/25 CHECK DATE APPROVED DATE 4600 Silicon Drive Durham, N.C 27703 Phone (919) 361-4770 TITLE Reel, MATERIAL PS SIZE FINAL PROTECTIVE FINISH SCALE C 1:2 7" x 12mm Wide DRAWING NO. 2400-00005 REV. B SHEET 1 OF 1 REV DRAWING NO. 15 B OF 1 xlamp XT-E LEDs Humidity Indicator Card (inside bag) Packaging Dessicant (inside bag) Unpackaged Reel Label with Cree Bin Code, Qty, Reel ID Packaged Reel Label with Cree Bin Code, Qty, Lot # Vacuum-Sealed Moisture Barrier Bag Label with Cree Order Code, Qty, Reel ID, PO # Label with Cree Bin Code, Qty, Reel ID Label with Custo Code, Qty, Reel I Boxed Reel Label with Cree Order Code, Qty, Reel ID, PO # Patent Label Label with Cree Bin Code, Qty, Reel ID Patent Label Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered of Cree, Inc. trademarks of Cree, Inc. 16