CLD-DS41 REV 10B
PRODUCT FAMILY DATA SHEET
Cree® XLamp® XT-E LEDs
WWW.CREE.COM/XLAMP
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice.
Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc.
PRODUCT DESCRIPTION
XLamp® XT-E is Cree’s highest
performing silicon carbide-based
LED technology, delivered in
Cree’s industry-standard XP/XT
packaging. XT-E White sets the
new standard for high performance
and dramatically lowers system
cost. XT-E Royal Blue is Cree’s
highest performing source of royal
blue light for remote-phosphor
applications.
Cree XLamp LEDs bring high
performance and quality of
light to a wide range of lighting
applications, including remote-
phosphor, color-changing, portable
and personal, outdoor, indoor-
directional, transportation, stage
and studio, commercial and
emergency-vehicle lighting.
FEATURES
• Available in white, 80-CRI min
white, 70-CRI min white and
royal blue
• Warm white available in 85- and
90-CRI min.
• New: available in 2200 K CCT
• Binned at 85 °C
• Coolwhiteefcacyofupto
148 lm/W (@ 85 °C, 350 mA)
• RoyalBluewallplugefciencyof
up to 53% (@ 85 °C, 350 mA)
• Wide viewing angle: 115-140°
• Thermal resistance: 5 °C/W
• Maximum drive current: 1.5 A
• Electrically neutral thermal path
• Vf binning supported for XT-E
White and Royal Blue
• XT-E Royal Blue sorted into
2.5-nm wavelength bins
• Unlimitedoorlifeat
≤30ºC/85%RH
• Reowsolderable-JEDEC
J-STD-020Ccompatible
• RoHS-andREACh-compliant
• UL-recognized component
(E349212)
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
www.cree.com/xlamp
Copyright © 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice.
Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc.
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
TABLE OF CONTENTS
Characteristics .......................... 2
Flux Characteristics .................... 3
Relative Spectral Power
Distribution .............................. 5
Relative Luminous Flux vs.
JunctionTemperature ................. 6
Electrical Characteristics ............. 7
Relative Luminous Flux vs.
Current .................................... 7
Relative Chromaticity vs. Current
and Temperature ....................... 9
Typical Spatial Distribution .........10
Thermal Design ........................11
ReowSolderingCharacteristics .12
Notes ......................................13
Mechanical Dimensions..............14
Tape and Reel ..........................15
Packaging ................................16
NOTE: For remote phosphor applications, a separate license to certain Cree patents is required.
xlamp xT-E lEDs
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
of Cree, Inc.
2
Copyright © 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered
trademarks of Cree, Inc.
2
CHARACTERISTICS
Characteristics Unit Minimum Typical Maximum
Thermal resistance, junction to solder point °C/W 5
Viewingangle(FWHM)-white degrees 115
Viewingangle(FWHM)-royalblue degrees 140
Temperaturecoefcientofvoltage mV/°C -2.5
ESDwithstandvoltage(HBMperMil-Std-883D) V 8000
DC forward current mA 1500
Reverse voltage V 5
Forward voltage (@ 350 mA, 85 °C) V 2.85 3.4
LED junction temperature °C 150
xlamp xT-E lEDs
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
of Cree, Inc.
3
Copyright © 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered
trademarks of Cree, Inc.
3
FLUX CHARACTERISTICS - WHITE (TJ = 85 °C)
The following table provides several base order codes for XLamp XT-E White LEDs. It is important to note that the base
order codes listed here are a subset of the total available order codes for the product family. For more order codes, as
well as a complete description of the order-code nomenclature, please consult the XLamp XT-E Binning and Labeling
document.
Color
CCT Range
Base Order Codes
Minimum Luminous Flux
@ 350 mA
Calculated Minimum
Luminous Flux (lm)**
@ 85 °C Order Code
Min. Max. Group Flux (lm)
@ 85 °C
Flux (lm)
@ 25 °C* 700 mA 1500 mA
Cool White 5000 K 8300 K
R3 122 140 217 376 XTEAWT-00-0000-000000F51
R4 130 149 231 401 XTEAWT-00-0000-000000G51
R5 139 160 247 428 XTEAWT-00-0000-000000H51
Outdoor White 4000 K 6200 K
R3 122 140 217 376 XTEAWT-00-0000-000000FE3
R4 130 149 231 401 XTEAWT-00-0000-000000GE3
R5 139 160 247 428 XTEAWT-00-0000-000000HE3
Neutral White 3700 K 5000 K
R2 114 131 203 351 XTEAWT-00-0000-000000EF4
R3 122 140 217 376 XTEAWT-00-0000-000000FF4
R4 130 149 231 401 XTEAWT-00-0000-000000GF4
Warm White 2200 K 3700 K
Q3 93.9 108 167 289 XTEAWT-00-0000-00000LBE7
Q4 100 115 178 308 XTEAWT-00-0000-00000LCE7
Q5 107 123 191 330 XTEAWT-00-0000-00000LDE7
70 CRI
Minimum
Neutral White
2600 K 8300 K
Q4 100 115 178 308 XTEAWT-00-0000-00000BCE7
Q5 107 123 191 330 XTEAWT-00-0000-00000BDF6
R2 114 131 203 351 XTEAWT-00-0000-00000BEF5
R3 122 140 217 376 XTEAWT-00-0000-00000BFC3
R4 130 149 231 401 XTEAWT-00-0000-00000BG53
80 CRI
Minimum White 2200 K 6200 K
Q3 93.9 108 167 289 XTEAWT-00-0000-00000HBE7
Q4 100 115 178 308 XTEAWT-00-0000-00000HCE6
Q5 107 123 191 330 XTEAWT-00-0000-00000HDE5
R2 114 131 203 351 XTEAWT-00-0000-00000HEF4
R3 122 140 217 376 XTEAWT-00-0000-00000HF50
85-CRI
Minimum
Warm White
2600 K 3700 K
P3 73.9 85 132 228 XTEAWT-00-0000-00000P8E7
P4 80.6 93 144 248 XTEAWT-00-0000-00000P9E7
Q2 87.4 100 156 269 XTEAWT-00-0000-00000PAE7
90-CRI
Minimum
Warm White
2600 K 3700 K
P3 73.9 85 132 228 XTEAWT-00-0000-00000U8E7
P4 80.6 93 144 248 XTEAWT-00-0000-00000U9E7
Q2 87.4 100 156 269 XTEAWT-00-0000-00000UAE7
Notes:
• Creemaintainsatoleranceof±7%onuxandpowermeasurements,±0.005onchromaticity(CCx,CCy)measurementsand±2
on CRI measurements.
• Typical CRI for Neutral White, 3,700 K - 5,000K CCT is 75.
• Typical CRI for Warm White, 2,200 K - 3,700 K CCT is 80.
* Flux values @ 25 °C are calculated and for reference only.
** Calculateduxvaluesat700mAand1500mAareforreferenceonly.
xlamp xT-E lEDs
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
of Cree, Inc.
4
Copyright © 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered
trademarks of Cree, Inc.
4
FLUX CHARACTERISTICS - ROYAL BLUE (TJ = 85 °C)
The following table provides order codes for XLamp XT-E Royal Blue LEDs. Additional information on the performance
grouping and codes for XT-E Royal Blue LEDs can be found in the XT-E Binning and Labeling document.
DWL
Kit
Codes
Dominant Wavelength Range
Order Codes, Minimum Radiant Flux @ 350 mA, Tj=85 °C
Min. Max.
Group DWL
(nm) Group DWL
(nm)
500 mW - Radiant Flux
Group Code 32 (L)
525 mW - Radiant Flux
Group Code 33 (M)
550 mW - Radiant Flux
Group Code 34 (N)
01 D36 450 D57 465 XTEARY-00-0000-000000L01 XTEARY-00-0000-000000M01 XTEARY-00-0000-000000N01
02 D36 450 D47 460 XTEARY-00-0000-000000L02 XTEARY-00-0000-000000M02 XTEARY-00-0000-000000N02
03 D46 455 D57 465 XTEARY-00-0000-000000L03 XTEARY-00-0000-000000M03 XTEARY-00-0000-000000N03
04 D36 450 D37 455 XTEARY-00-0000-000000L04 XTEARY-00-0000-000000M04 XTEARY-00-0000-000000N04
05 D46 455 D47 460 XTEARY-00-0000-000000L05 XTEARY-00-0000-000000M05 XTEARY-00-0000-000000N05
06 D56 460 D57 465 XTEARY-00-0000-000000L06 XTEARY-00-0000-000000M06 XTEARY-00-0000-000000N06
07 D37 452.5 D46 457.5 XTEARY-00-0000-000000L07 XTEARY-00-0000-000000M07 XTEARY-00-0000-000000N07
08 D47 457.5 D56 462.5 XTEARY-00-0000-000000L08 XTEARY-00-0000-000000M08 XTEARY-00-0000-000000N08
09 D37 452.5 D56 462.5 XTEARY-00-0000-000000L09 XTEARY-00-0000-000000M09 XTEARY-00-0000-000000N09
DWL
Kit
Codes
Dominant Wavelength Range Order Codes, Minimum Radiant Flux @ 350 mA,
Tj=85 °C
Min. Max.
Group DWL
(nm) Group DWL
(nm)
575 mW - Radiant Flux
Group Code 35 (P)
600 mW - Radiant Flux
Group Code 36 (Q)
01 D36 450 D57 465 XTEARY-00-0000-000000P01 XTEARY-00-0000-000000Q01
02 D36 450 D47 460 XTEARY-00-0000-000000P02 XTEARY-00-0000-000000Q02
03 D46 455 D57 465 XTEARY-00-0000-000000P03
04 D36 450 D37 455 XTEARY-00-0000-000000P04 XTEARY-00-0000-000000Q04
05 D46 455 D47 460 XTEARY-00-0000-000000P05
06 D56 460 D57 465
07 D37 452.5 D46 457.5 XTEARY-00-0000-000000P07
08 D47 457.5 D56 462.5
09 D37 452.5 D56 462.5 XTEARY-00-0000-000000P09
Note:
• Creemaintainsatoleranceof±7%onuxandpowermeasurements,±0.005onchromaticity(CCx,CCy)measurements,±2on
CRI measurements and ± 1 nm on dominant wavelength measurements.
xlamp xT-E lEDs
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
of Cree, Inc.
5
Copyright © 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered
trademarks of Cree, Inc.
5
RELATIVE SPECTRAL POWER DISTRIBUTION - WHITE
RELATIVE SPECTRAL POWER DISTRIBUTION - ROYAL BLUE
Relative Spectral Power
0
20
40
60
80
100
400 450 500 550 600 650 700 750
Relative Radiant Power (%)
Wavelength (nm)
5000K - 8300K CCT
2600K - 3700K CCT
2200K CCT
Relative Spectral Power
0%
20%
40%
60%
80%
100%
400 450 500 550 600 650 700 750
Relative Radiant Power (%)
Royal Blue
xlamp xT-E lEDs
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
of Cree, Inc.
6
Copyright © 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered
trademarks of Cree, Inc.
6
RELATIVE LUMINOUS FLUX VS. JUNCTION TEMPERATURE (IF = 350 mA) - WHITE
RELATIVE RADIANT FLUX VS. JUNCTION TEMPERATURE (IF = 350 mA) - ROYAL BLUE
Relative Flux Output vs. Junction Temperature
0%
20%
40%
60%
80%
100%
120%
25 50 75 100 125 150
Relative Luminous Flux
Junction Temperature (ºC)
Relative Flux Output vs. Junction Temperature
0%
20%
40%
60%
80%
100%
120%
25 50 75 100 125 150
Relative Radiant Flux
Junction Temperature (ºC)
xlamp xT-E lEDs
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
of Cree, Inc.
7
Copyright © 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered
trademarks of Cree, Inc.
7
ELECTRICAL CHARACTERISTICS (TJ = 85 °C)
RELATIVE LUMINOUS FLUX VS. CURRENT (TJ = 85 °C) - WHITE
Electrical Characteristics (Tj = 85ºC)
0
200
400
600
800
1000
1200
1400
1600
2.50 2.75 3.00 3.25 3.50
Forward Current (mA)
Forward Voltage (V)
Relative Intensity vs. Current (Tj = 85ºC)
0%
50%
100%
150%
200%
250%
300%
350%
0200 400 600 800 1000 1200 1400 1600
Relative Luminous Flux (%)
Forward Current (mA)
xlamp xT-E lEDs
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
of Cree, Inc.
8
Copyright © 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered
trademarks of Cree, Inc.
8
RELATIVE RADIANT FLUX VS. CURRENT (TJ = 85 °C) - ROYAL BLUE
Relative Radiant Flux vs. Current (Tj = 85ºC)
0%
50%
100%
150%
200%
250%
300%
350%
0200 400 600 800 1000 1200 1400 1600
Relative Radiant Flux (%)
Forward Current (mA)
xlamp xT-E lEDs
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
of Cree, Inc.
9
Copyright © 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered
trademarks of Cree, Inc.
9
RELATIVE CHROMATICITY VS. CURRENT AND TEMPERATURE (WARM WHITE)
Relative Chromaticity Vs. Current, WW
-0.020
-0.015
-0.010
-0.005
0.000
0.005
0.010
0.015
0.020
0200 400 600 800 1000 1200 1400 1600
Current (mA)
ΔCCx
ΔCCy
TJ=85 °C
Relative Chromaticity Vs. Temperature WW
-0.020
-0.015
-0.010
-0.005
0.000
0.005
0.010
0.015
0.020
020 40 60 80 100 120 140 160
Tsp (°C)
ΔCCx
ΔCCy
IF=350 mA
xlamp xT-E lEDs
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
of Cree, Inc.
10
Copyright © 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered
trademarks of Cree, Inc.
10
TYPICAL SPATIAL DISTRIBUTION - WHITE
TYPICAL SPATIAL DISTRIBUTION - ROYAL BLUE
Typical Spatial Radiation Pattern
0
20
40
60
80
100
120
-90 -70 -50 -30 -10 10 30 50 70 90
Relative Luminous Intensity (%)
Angle (º)
Typical Spatial Distribution
0
20
40
60
80
100
120
-90 -70 -50 -30 -10 10 30 50 70 90
Relative Luminous Intensity (%)
Angle (º)
xlamp xT-E lEDs
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
of Cree, Inc.
11
Copyright © 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered
trademarks of Cree, Inc.
11
THERMAL DESIGN
The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is
crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to
ambient in order to optimize lamp life and optical characteristics.
Thermal Design
0
200
400
600
800
1000
1200
1400
1600
020 40 60 80 100 120 140
Maximum Current (mA)
Ambient Temperature (ºC)
Rj-a = 10°C/W
Rj-a = 15°C/W
Rj-a = 20°C/W
Rj-a = 25°C/W
xlamp xT-E lEDs
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
of Cree, Inc.
12
Copyright © 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered
trademarks of Cree, Inc.
12
REFLOW SOLDERING CHARACTERISTICS
Intesting,CreehasfoundXLampXT-ELEDstobecompatiblewithJEDECJ-STD-020C,usingtheparameterslisted
below.Asageneralguideline,Creerecommendsthatusersfollowtherecommendedsolderingproleprovidedbythe
manufacturer of solder paste used.
NotethatthisgeneralguidelinemaynotapplytoallPCBdesignsandcongurationsofreowsolderingequipment.
Prole Feature Lead-Based Solder Lead-Free Solder
Average Ramp-Up Rate (Tsmax to Tp) 3 °C/second max. 3 °C/second max.
Preheat: Temperature Min (Tsmin) 100 °C 150 °C
Preheat: Temperature Max (Tsmax) 150 °C 200 °C
Preheat: Time (tsmin to tsmax) 60-120 seconds 60-180 seconds
Time Maintained Above: Temperature (TL) 183 °C 217 °C
Time Maintained Above: Time (tL) 60-150 seconds 60-150 seconds
Peak/ClassicationTemperature(Tp) 215 °C 260 °C
Time Within 5 °C of Actual Peak Temperature (tp) 10-30 seconds 20-40 seconds
Ramp-Down Rate 6 °C/second max. 6 °C/second max.
Time 25 °C to Peak Temperature 6 minutes max. 8 minutes max.
Note: All temperatures refer to the topside of the package, measured on the package body surface.
TP
TL
Temperature
Time
t 25˚C to Peak
Preheat
ts
tS
tP
25
Ramp-down
Ramp-up
Critical Zone
TL to TP
Tsmax
Tsmin
xlamp xT-E lEDs
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
of Cree, Inc.
13
Copyright © 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered
trademarks of Cree, Inc.
13
NOTES
Lumen Maintenance Projections
Cree now uses standardized IES LM-80-08 and TM-21-11 methods for collecting long-term data and extrapolating LED
lumenmaintenance.ForinformationonthespecicLM-80datasetsavailableforthisLED,refertothepublicLM-80
results document at www.cree.com/xlamp_app_notes/LM80_results.
Please read the XLamp Long-Term Lumen Maintenance application note at www.cree.com/xlamp_app_notes/lumen_
maintenance for more details on Cree’s lumen maintenance testing and forecasting. Please read the XLamp Thermal
Management application note at www.cree.com/xlamp_app_notes/thermal_management for details on how thermal
design, ambient temperature, and drive current affect the LED junction temperature.
Moisture Sensitivity
Intesting,CreehasfoundXLampXT-ELEDstohaveunlimitedoorlifeinconditions≤30ºC/85%relativehumidity
(RH).Moisturetestingincludeda168-hoursoakat85ºC/85%RHfollowedby3reowcycles,withvisualandelectrical
inspections at each stage.
Cree recommends keeping XLamp LEDs in their sealed moisture-barrier packaging until immediately prior to use. Cree
also recommends returning any unused LEDs to the resealable moisture-barrier bag and closing the bag immediately
fter use.
RoHS Compliance
ThelevelsofRoHSrestrictedmaterialsinthisproductarebelowthemaximumconcentrationvalues(alsoreferredto
as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU
Directive2011/65/EC(RoHS2),asimplementedJanuary2,2013.RoHSDeclarationsforthisproductcanbeobtained
from your Cree representative or from the Product Ecology section of www.cree.com.
REACh Compliance
REACh substances of high concern (SVHCs) information is available for this product. Since the European Chemical
Agency(ECHA)haspublishednoticesoftheirintenttofrequentlyrevisetheSVHClistingfortheforeseeablefuture,
pleasecontactaCreerepresentativetoinsureyougetthemostup-to-dateREAChDeclaration.HistoricalREAChbanned
substance information (substances restricted or banned in the EU prior to 2010) is also available upon request.
UL Recognized Component
Level4enclosureconsideration.TheLEDpackageoraportionthereofhasbeen investigatedasareand electrical
enclosure per ANSI/UL 8750.
Vision Advisory Claim
WARNING: Do not look at an exposed lamp in operation. Eye injury can result. See LED Eye Safety at www.cree.com/
xlamp_app_notes/led_eye_safety.
xlamp xT-E lEDs
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
of Cree, Inc.
14
Copyright © 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered
trademarks of Cree, Inc.
14
MECHANICAL DIMENSIONS
All measurements are ±.13 mm unless otherwise indicated.
Top View Bottom View
Side View
Recommended PCB Solder Pad Recommended Stencil Pattern
(Shaded Area Is Open)
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT
THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
± .5 °
.XXX ± .25
.XX ± .75
.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125
± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
1.6
1.30
.65
.50
2.30
3.30
1.15
3.450
3.450
2.36
.83
.650
R1.530
.50
.50
.40
1.30
3.30
3.30
1.15
.65
1.65
.50
1.20
.60
.60
3.20
1.60
3.20
.40
.40
.40
1/124.000
B
2610-00015
OUTLINE DRAWING XP HEW
--
--
----
----
3/8/11D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
B REMOVED CHIP DIMENSIONS DC 5/11/11
RECOMMENDED PCB SOLDER PAD
RECOMMENDED STENCIL PATTERN
(HATCHED AREA IS OPENING)
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT
THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
± .5 °
.XXX ± .25
.XX ± .75
.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125
± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
1.6
1.30
.65
.50
2.30
3.30
1.15
3.450
3.450
2.36
.83
.650
R1.530
.50
.50
.40
1.30
3.30
3.30
1.15
.65
1.65
.50
1.20
.60
.60
3.20
1.60
3.20
.40
.40
.40
1/124.000
B
2610-00015
OUTLINE DRAWING XP HEW
--
--
----
----
3/8/11D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
B REMOVED CHIP DIMENSIONS DC 5/11/11
RECOMMENDED PCB SOLDER PAD
RECOMMENDED STENCIL PATTERN
(HATCHED AREA IS OPENING)
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT
THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
± .5 °
.XXX ± .25
.XX ± .75
.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125
± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
1.6
1.30
.65
.50
2.30
3.30
1.15
3.450
3.450
2.36
.83
.650
R1.530
.50
.50
.40
1.30
3.30
3.30
1.15
.65
1.65
.50
1.20
.60
.60
3.20
1.60
3.20
.40
.40
.40
1/124.000
B
2610-00015
OUTLINE DRAWING XP HEW
--
--
----
----
3/8/11D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
B REMOVED CHIP DIMENSIONS DC 5/11/11
RECOMMENDED PCB SOLDER PAD
RECOMMENDED STENCIL PATTERN
(HATCHED AREA IS OPENING)
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT
THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
± .5 °
.XXX ± .25
.XX ± .75
.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125
± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
1.6
1.30
.65
.50
2.30
3.30
1.15
3.450
3.450
2.36
.83
.650
R1.530
.50
.50
.40
1.30
3.30
3.30
1.15
.65
1.65
.50
1.20
.60
.60
3.20
1.60
3.20
.40
.40
.40
1/124.000
B
2610-00015
OUTLINE DRAWING XP HEW
--
--
----
----
3/8/11D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
B REMOVED CHIP DIMENSIONS DC 5/11/11
RECOMMENDED PCB SOLDER PAD
RECOMMENDED STENCIL PATTERN
(HATCHED AREA IS OPENING)
ANODE
ANODE
xlamp xT-E lEDs
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
of Cree, Inc.
15
Copyright © 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered
trademarks of Cree, Inc.
15
TAPE AND REEL
AllCreecarriertapesconformtoEIA-481D,AutomatedComponentHandlingSystemsStandard.
All dimensions in mm.
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT
THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
± .5 °
.XXX ± .25
.XX ± .75
.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125
± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
1.6
Trailer
160mm (min) of
empty pockets
sealed with tape
(20 pockets min.)
Loaded Pockets
(1000 Lamps)
Leader
400mm (min.) of
empty pockets with
at least 100mm
sealed by tape
(50 empty pockets min.)
12.0
+.3
-.0
1.75
±.10
4±.1
8±.1 2.5±.1
1/13.000
B
2402-00014
XP HEW LOADING SPEC
--
--
----
----
11/29/10D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
B
ADDED CATHODE AND ANODE NOTE
REORIENTED DEVICE
DC 2/26/12
END START
User Feed Direction
CATHODE SIDE
ANODE SIDE
User Feed Direction
7"
1.5± .1
13mm
Pocket Tape
Carrier Tape
13
61
12.40 0
+
2.00
MEASURED AT HUB
12.40
MEASURED AT INSIDE EDGE
16.40
SHEET 1 OF 1
1:2
2400-00005
SIZE
TITLE
REV.
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
.X ± 0.3
X° ± 2°
.XX ± .10
.X ± .25
FOR SHEET METAL PARTS ONLY
.XX ± .13
X° ± 1°
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS & BEFORE FINISH.
TOLERANCE UNLESS SPECIFIED:
SCALE
A
B
C
D
1
23456
65432
1
A
B
C
D
Phone (919) 361-4770
4600 Silicon Drive
Durham, N.C 27703
NOTICE
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
CONTAINED WITHIN ARE THE PROPRIETARY AND
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT
OF CREE, INC.
Reel,
7" x 12mm Wide
B
LIUDEZHI
2012/5/25
+/-
0.5
PS
190
½öÓÃÓÚÆÀ¹À¡£
°æȨËùÓÐ (c) by Foxit Software Company, 2004
ÓÉ Foxit PDF Editor ±à¼-
OD 7.5''
13
61
12.40 0
+
2.00
MEASURED AT HUB
12.40
MEASURED AT INSIDE EDGE
16.40
SHEET 1 OF 1
1:2
2400-00005
SIZE
TITLE
REV.
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
.X ± 0.3
X° ± 2°
.XX ± .10
.X ± .25
FOR SHEET METAL PARTS ONLY
.XX ± .13
X° ± 1°
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS & BEFORE FINISH.
TOLERANCE UNLESS SPECIFIED:
SCALE
A
B
C
D
1
23456
65432
1
A
B
C
D
Phone (919) 361-4770
4600 Silicon Drive
Durham, N.C 27703
NOTICE
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
CONTAINED WITHIN ARE THE PROPRIETARY AND
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT
OF CREE, INC.
Reel,
7" x 12mm Wide
B
LIUDEZHI
2012/5/25
+/-
0.5
PS
190
½öÓÃÓÚÆÀ¹À¡£
°æȨËùÓÐ (c) by Foxit Software Company, 2004
ÓÉ Foxit PDF Editor ±à¼-
OD 7.5''
Y
Y
XX
REF 0.59
W
F(III)
P1
D1
1.5 MIN.
Bo
Ao
R0.2
TYPICAL
REF 4.375
Ko
Other material available.(IV)
(III)
(II)
(I)
hole to centerline of pocket.
Measured from centerline of sprocket
holes is ± 0.20.
Cumulative tolerance of 10 sprocket
to centerline of pocket.
Measured from centerline of sprocket hole
SECTION Y-Y
SECTION X-X
2.0 ±0.05 (I)
P2
1.55 ±0.05
Do
4.0 ±0.1 (II)
Po
1.75 ±0.1
E1
0.30 ±0.05
T
REF R 2.24
2.40Ko +0.0/-0.1
3.70
1
W
F
P
+/- 0.05
+/- 0.1
+0.3/-0.1
5.50
8.00
12.00
Ao 3.70 +/- 0.1
Bo +/- 0.1
Y
Y
XX
REF 0.59
W
F(III)
P1
D1
1.5 MIN.
Bo
Ao
R0.2
TYPICAL
REF 4.375
Ko
Other material available.(IV)
(III)
(II)
(I)
hole to centerline of pocket.
Measured from centerline of sprocket
holes is ± 0.20.
Cumulative tolerance of 10 sprocket
to centerline of pocket.
Measured from centerline of sprocket hole
SECTION Y-Y
SECTION X-X
2.0 ±0.05 (I)
P2
1.55 ±0.05
Do
4.0 ±0.1 (II)
Po
1.75 ±0.1
E1
0.30 ±0.05
T
REF R 2.24
2.40Ko +0.0/-0.1
3.70
1
W
F
P
+/- 0.05
+/- 0.1
+0.3/-0.1
5.50
8.00
12.00
Ao 3.70 +/- 0.1
Bo +/- 0.1
Y
Y
XX
REF 0.59
W
F(III)
P1
D1
1.5 MIN.
Bo
Ao
R0.2
TYPICAL
REF 4.375
Ko
Other material available.(IV)
(III)
(II)
(I)
hole to centerline of pocket.
Measured from centerline of sprocket
holes is ± 0.20.
Cumulative tolerance of 10 sprocket
to centerline of pocket.
Measured from centerline of sprocket hole
SECTION Y-Y
SECTION X-X
2.0 ±0.05 (I)
P2
1.55 ±0.05
Do
4.0 ±0.1 (II)
Po
1.75 ±0.1
E1
0.30 ±0.05
T
REF R 2.24
2.40Ko +0.0/-0.1
3.70
1
W
F
P
+/- 0.05
+/- 0.1
+0.3/-0.1
5.50
8.00
12.00
Ao 3.70 +/- 0.1
Bo +/- 0.1
CATHODESIDE
ANODE SIDE
xlamp xT-E lEDs
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks
of Cree, Inc.
16
Copyright © 2011-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered
trademarks of Cree, Inc.
16
PACKAGING
Label with Cree Bin
Code, Qty, Lot # Label with Cree Bin
Code, Qty, Lot #
Vacuum-Sealed
Moisture Barrier Bag
Dessicant
(inside bag)
Humidity Indicator
Card (inside bag)
Patent Label
Label with Customer Order
Code, Qty, Reel ID, PO #
Patent Label
Label with Cree Bin
Code, Qty, Reel ID
Label with Cree Bin
Code, Qty, Reel ID
Label with Cree Order Code,
Qty, Reel ID, PO #
Label with Cree Order Code,
Qty, Reel ID, PO #
Label with Cree Bin
Code, Qty, Reel ID
Unpackaged Reel
Packaged Reel
Boxed Reel