Evaluation Board for the AD7265/AD7266 EVAL-AD7265/AD7266 FEATURES Full details on the AD7265 and the AD7266 are available in the device data sheets, which are available from Analog Devices, Inc., and should be consulted in conjunction with this data sheet when using the evaluation board. Full-featured evaluation board for the AD7265 and AD7266 EVAL-CED1Z compatible Standalone capability On-board analog buffering and voltage reference On-board single-ended-to-differential conversion Various linking options PC software for control and data analysis when used with EVAL-CED1Z On-board components include an AD780, which is a pin programmable 2.5 V or 3 V ultrahigh precision band gap reference, nine AD8022 dual op amps, and a 7S04 digital buffer. Various link options are explained in Table 1. Interfacing to this evaluation board is through a 96-way connector. This 96-way connector is compatible with the EVAL-CED1Z, which is available from Analog Devices. External sockets are provided for a number of signals, including the VREF input, the analog inputs, and the digital inputs and outputs. GENERAL DESCRIPTION This data sheet describes the evaluation board for the AD7265 and the AD7266, which are dual, 12-bit, high speed, low power successive approximation ADCs that operate from a single 2.7 V to 5.25 V power supply and feature throughput rates up to 2 MSPS. FUNCTIONAL BLOCK DIAGRAM EXTERNAL SUPPLY BIPOLAR SINGLE-ENDED INPUT S/E TO DIFF CONVERSION USING AD8138 .. .. VA1 S/E TO DIFF CONVERSION USING AD8138 VA6 AVDD DVDD VDRIVE .. .. A0 A1 SCLK SINGLE-ENDED INPUT BUFFERING UNIPOLAR SINGLE-ENDED INPUTS VB1 .. .. .. .. VB6 96-WAY EDGE CONNECTOR BIPOLAR SINGLE-ENDED INPUT CS DOUTA DOUTB AD7265/AD7266 DCAP A/DCAP B BIPOLAR INPUT OPTIONAL BIAS-UP CIRCUITRY FOR S/E TO DIFF OPERATION UNIPOLAR OUTPUT UNIPOLAR OUTPUT EXTERNAL VREF POWER SUPPLY CIRCUITS 07921-001 BIPOLAR INPUT Figure 1. Rev. 0 Evaluation boards are only intended for device evaluation and not for production purposes. Evaluation boards are supplied "as is" and without warranties of any kind, express, implied, or statutory including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose. No license is granted by implication or otherwise under any patents or other intellectual property by application or use of evaluation boards. Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Analog Devices reserves the right to change devices or specifications at any time without notice. Trademarks and registered trademarks are the property of their respective owners. Evaluation boards are not authorized to be used in life support devices or systems. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)2009 Analog Devices, Inc. All rights reserved. EVAL-AD7265/AD7266 TABLE OF CONTENTS Features .............................................................................................. 1 Operating with the EVAL-CED1Z ........................................... 13 General Description ......................................................................... 1 Evaluation Board Software ............................................................ 14 Functional Block Diagram .............................................................. 1 Installing the Software ............................................................... 14 Revision History ............................................................................... 2 Setting Up the EVAL-CED1Z ................................................... 14 Evaluation Board Hardware ............................................................ 3 Software Operation .................................................................... 15 Power Supplies .............................................................................. 3 Using the Software ..................................................................... 16 Link Options ................................................................................. 3 Taking Samples ........................................................................... 17 Setup Conditions .......................................................................... 8 Evaluation Board Schematics and Artwork ................................ 18 Sockets ......................................................................................... 11 Ordering Information .................................................................... 23 Connectors .................................................................................. 11 Bill of Materials ........................................................................... 23 Interfacing the Evaluation Board to the EVAL-CED1Z ........ 12 Ordering Guide .......................................................................... 23 Test Points .................................................................................... 12 ESD Caution................................................................................ 23 REVISION HISTORY 4/09--Revision 0: Initial Version Rev. 0 | Page 2 of 24 EVAL-AD7265/AD7266 EVALUATION BOARD HARDWARE POWER SUPPLIES When using this evaluation board with the EVAL-CED1Z, all supplies are provided from the EVAL-CED1Z through the 96-way connector. When using the board as a standalone unit, external supplies must be provided. This evaluation board has the following power supply inputs: +12 V, -12 V, AVDD (+5 V), DVDD (+5 V), AGND, VDRIVE, and DGND. The +12 V supply is only required if the external AD780 voltage reference and op amps are to be used. The supplies are decoupled to the relevant ground plane with 10 F tantalum and 0.1 F multilayer ceramic capacitors at the point where they enter the board. The supply pins for the exter- nal reference are also decoupled to AGND with a 470 nF ceramic capacitor. The AD7265/AD7266 AVDD and VDRIVE supply pins are also decoupled to AGND, while DVDD is decoupled to DGND, with a 0.1 F multilayer ceramic capacitor and a 10 F tantalum capacitor at the device pins. Extensive ground planes are used on this board to minimize the effect of high frequency noise interference. There are two ground planes, AGND and DGND. These are connected at one location close to the AD7265/AD7266. LINK OPTIONS There are 49 link options that must be set correctly to select the appropriate operating setup before using the evaluation board. The functions of the link options are outlined in Table 1. Table 1. Link Function Descriptions Link No. LK1 LK2 LK3 LK4 LK5 LK6 Description This link option selects the source of the VA1 analog input. In Position A, VA1 is supplied from the output of the unity gain buffer, U3-A, in which case a signal must be applied to the SVIN1 SMB socket via J13. In Position B, VA1 is supplied from the positive output (V1+) of the single-ended-to-differential converter, U5-B, in which case a single-ended signal must be applied to V1 DIFF via Socket J17. In Position C, VA1 is tied to AGND. If this channel is not in use, this link should be in Position C. This link option selects the source of the VA2 analog input. In Position A, VA2 is supplied from the output of the unity gain buffer, U3-B, in which case a signal must be applied to the SVIN2 socket via J14. In Position B, VA2 is supplied from the negative output (V1-) of the single-ended-to-differential converter, U5-A, in which case a single-ended signal must be applied to V1 DIFF via Socket J17. In Position C, VA2 is tied to AGND. If this channel is not in use, this link should be in Position C. This link option selects the source of the VA3 analog input. In Position A, VA3 is supplied from the output of the unity gain buffer, U3-A, in which case a signal must be applied to the SVIN1 socket via J13. In Position B, VA3 is supplied from the positive output (V2+) of the single-ended-to-differential converter, U6-B, in which case a single-ended signal must be applied to V2 DIFF via Socket J19. In Position C, VA3 is tied to AGND. If this channel is not in use, this link should be in Position C. This link option selects the source of the VA4 analog input. In Position A, VA4 is supplied from the output of the unity gain buffer, U3-B, in which case a signal must be applied to the SVIN2 socket via J14. In Position B, VA4 is supplied from the negative output (V2-) of the single-ended-to-differential converter, U6-A, in which case a single-ended signal must be applied to V2 DIFF via Socket J19. In Position C, VA4 is tied to AGND. If this channel is not in use, this link should be in Position C. This link option selects the source of the VA5 analog input. In Position A, VA5 is supplied from the output of the unity gain buffer, U3-A, in which case a signal must be applied to the SVIN1 socket via J13. In Position B, VA5 is supplied from the positive output (V1+) of the single-ended-to-differential converter, U5-B, in which case a single-ended signal must be applied to V1 DIFF via Socket J17. In Position C, VA5 is tied to AGND. If this channel is not in use, this link should be in Position C. This link option selects the source of the VA6 analog input. In Position A, VA6 is supplied from the output of the unity gain buffer, U3-B, in which case a signal must be applied to the SVIN2 socket via J14. In Position B, VA6 is supplied from the negative output (V1-) of the single-ended-to-differential converter, U5-A, in which case a single-ended signal must be applied to V1 DIFF via Socket J17. In Position C, VA6 is tied to AGND. If this channel is not in use, this link should be in Position C. Rev. 0 | Page 3 of 24 EVAL-AD7265/AD7266 Link No. LK7 LK8 LK9 LK10 LK11 LK12 LK13 LK14 LK15 Description This link option selects the source of the VB1 analog input. In Position A, VB1 is supplied from the output of the unity gain buffer, U4-A, in which case a signal must be applied to the SVIN3 socket via J15. In Position B, VB1 is supplied from the positive output (V3+) of the single-ended-to-differential converter, U7-B, in which case a single-ended signal must be applied to V3 DIFF via Socket J20. In Position C, VB1 is tied to AGND. If this channel is not in use, this link should be in Position C. This link option selects the source of the VB2 analog input. In Position A, VB2 is supplied from the output of the unity gain buffer, U4-B, in which case a signal must be applied to the SVIN4 socket via J16. In Position B, VB2 is supplied from the negative output (V3-) of the single-ended-to-differential converter, U7-A, in which case a single-ended signal must be applied to V3 DIFF via Socket J20. In Position C, VB2 is tied to AGND. If this channel is not in use, this link should be in Position C. This link option selects the source of the VB3 analog input. In Position A, VB3 is supplied from the output of the unity gain buffer, U4-A, in which case a signal must be applied to the SVIN3 socket via J15. In Position B, VB3 is supplied from the positive output (V4+) of the single-ended-to-differential converter, U8-B, in which case a single-ended signal must be applied to V4 DIFF via Socket J22. In Position C, VB3 is tied to AGND. If this channel is not in use, this link should be in Position C. This link option selects the source of the VB4 analog input. In Position A, VB4 is supplied from the output of the unity gain buffer, U4-B, in which case a signal must be applied to the SVIN4 socket via J16. In Position B, VB4 is supplied from the negative output (V4-) of the single-ended-to-differential converter, U8-A, in which case a single-ended signal must be applied to V4 DIFF via Socket J22. In Position C, VB4 is tied to AGND. If this channel is not in use, this link should be in Position C. This link option selects the source of the VB5 analog input. In Position A, VB5 is supplied from the output of the unity gain buffer, U4-A, in which case a signal must be applied to the SVIN3 socket via J15. In Position B, VB5 is supplied from the positive output (V3+) of the single-ended-to-differential converter, U7-B, in which case a single-ended signal must be applied to V3 DIFF via Socket J20. In position C, VB5 is tied to AGND. If this channel is not in use, this link should be in Position C. This link option selects the source of the VB6 analog input. In Position A, VB6 is supplied from the output of the unity gain buffer, U4-B, in which case a signal must be applied to the SVIN4 socket via J16. In Position B, VB6 is supplied from the negative output (V3-) of the single-ended-to-differential converter, U7-A, in which case a single-ended signal must be applied to V3 DIFF via Socket J20. In Position C, VB6 is tied to AGND. If this channel is not in use, this link should be in Position C. This link option selects the source or destination of the reference voltage applied to or received from the DCAPA pin of the AD7265/AD7266. In Position A, an external reference signal can be applied to the DCAPA pin via J24, or the internal reference voltage from the AD7266/AD7265 can be accessed via J24. This link should be used in conjunction with LK19, which determines whether an internal or external reference is used with the device. In Position B, the AD780 provides an external 2.5 V reference to the DCAPA pin. This link should be set up in conjunction with LK16. If both Link Option A and Link Option B are inserted, the AD780 provides the reference voltage for the AD7265/AD7266, which is also output via J24. This link option selects the source or destination of the reference voltage applied to or received from the DCAPB pin of the AD7265/AD7266. In Position A, an external reference signal can be applied to the DCAPB pin via J25, or the internal reference voltage from the AD7265/AD7266 can be accessed via J25. This link should be used in conjunction with LK19, which determines whether an internal or external reference is used with the device. In Position B, the AD780 provides an external 2.5 V reference to the DCAPB pin. This link should be set up in conjunction with LK16. If both Link Option A and Link Option B are inserted, the AD780 provides the reference voltage, which is output via J25. This link option selects the source of the AVDD and DVDD supply for the AD7265/AD7266. In Position A, VDD (+5 V) is supplied from the EVAL-CED1Z. In Position B, the VDD voltage must be supplied from an external source via J2. Rev. 0 | Page 4 of 24 EVAL-AD7265/AD7266 Link No. LK16 LK17 LK18 LK19 LK20 LK21 LK22 LK23 LK24 LK25 LK26 LK27 LK28 LK29 LK30 Description This link option sets the output reference voltage delivered by the AD780. When this link is inserted, the AD780 output voltage is set to +3.0 V. When this link is removed, the AD780 output voltage is set to +2.5 V. This link option selects the source of the VDRIVE supply for the AD7265/AD7266. In Position A, VDRIVE is supplied from the EVAL-CED1Z. The value of VDRIVE in this case is 3.3 V. In Position B, the VDRIVE supply must be supplied from an external source via J3. Note that the logic interface on the EVAL-CED1Z operates at 3.3 V. Not populated. This link option selects the logic input to the REF SELECT pin. In Position A, the REF SELECT pin is tied to VDRIVE (Logic 1). Therefore, an external reference must be supplied through the DCAPA/DCAPB pins. In Position B, the REF SELECT pin is tied to DGND (Logic 0). Therefore, the internal on-chip 2.5 V reference is used. This link option selects the logic input to the RANGE pin. In Position A, the RANGE pin is tied to VDRIVE (Logic 1). Therefore, the device is configured for an analogue input range of 0 V to 2 VREF. In Position B, the RANGE pin is tied to DGND (Logic 0). Therefore, the analogue input range is 0 V to VREF. This link option selects the logic input to the SGL/DIFF pin. In Position A, the ADC is tied to VDRIVE and, therefore, the ADC is configured to operate in single-ended mode. In Position B, the ADC is tied to DGND and, therefore, the ADC is configured to operate in differential mode. This link option selects the source of the logic input to the A0 pin. It should be used in conjunction with LK23 and LK24 to determine the pair of channels to be simultaneously converted. In Position A, the A0 pin is tied to a VDRIVE, a high logic level. In Position B, the logic level applied to the A0 pin is controlled via the channel selection option in the software. In Position C, the A0 pin is tied to DGND, a low logic level. In Position D, an external A0 logic level can be applied through the external socket, J6. This link option selects the source of the logic input to the A1 pin; it should be used in conjunction with LK22 and LK24, to determine the pair of channels to be simultaneously converted. In Position A, the A1 pin is tied to VDRIVE, a high logic level. In Position B, the logic level applied to A1 is controlled via the channel selection icon in the software. In Position C, the A1 pin is tied to DGND, a low logic level. In Position D, an external A1 logic level can be applied through the external socket, J7. This link option selects the source of the logic input to the A2 pin; it should be used in conjunction with LK22 and LK23 to determine the pair of channels to be simultaneously converted. In Position A, the A2 pin is tied to VDRIVE, a high logic level. In Position B, the logic level applied to A1 is controlled via the channel selection option in the software. In Position C, the A2 pin is tied to DGND, a low logic level. In Position D, an external A2 value can be applied through the external socket, J8. This link option selects the source of the CS input. In Position A, the CS input is provided by the EVAL-CED1Z. In Position B, the CS input is provided via the external SMB socket, J9. Not populated. This link option selects the source of the SCLK input. In Position A, the SCLK input is provided via the external SMB socket, J10. In Position B, the SCLK input is provided by the EVAL-CED1Z. This link option selects the destination of the serial data output (DOUTA). In Position A, the data is supplied to the EVAL-CED1Z. In Position B, the data is supplied to the external SMB socket, J11. This link option selects the destination of the serial data output (DOUTB). In Position A, the data is supplied to the EVAL-CED1Z. In Position B, the data is supplied to the external SMB socket, J12. Not populated. Rev. 0 | Page 5 of 24 EVAL-AD7265/AD7266 Link No. LK31 LK32 and LK34 LK33 LK35 LK36 LK37 and LK39 LK38 LK40 LK41 LK42 and LK44 LK43 LK45 LK46 LK47 and LK49 Description This link option adds a 50 termination to AGND at the V1 DIFF socket (J17) for differential operation. This link is removed when using the single-ended-to-differential converter. When this link is inserted, a 50 termination is added to the input signal applied to VI DIFF socket (J17). This link should be inserted if this circuit is not being used to ground the input to U5-B. These link options are used in conjunction with each other to set up the AD8022 (U5) dual op amp configuration to convert either a bipolar or unipolar single-ended signal into a differential signal centered on the common-mode voltage. Both links should be closed when the bipolar analog input signal biased around 0 V is applied to J17. Both links should be open when a unipolar analog input biased around 2.5 V is applied to J17. LK32 should be closed when this circuit is not being used. This link option selects the common-mode voltage applied to U5-A, the AD8022 dual op amp configuration used to perform single-ended-to-differential conversion on the analog input. In Position A, an external common-mode voltage can be applied to U5-A via J18. In Position B, the +VS input to the AD8022 is tied to AGND, in which case the AD8022 dual op amp is not used. In Position C, a portion of VREF is applied to U5-A to set up the common-mode voltage. Not populated. This link option adds a 50 termination to AGND at the V2 DIFF socket (J19) used for differential operation. This link is removed when using the single-ended-to-differential converter. When this link is inserted, a 50 termination is added to the input signal applied to the V2 DIFF socket (J19). This link should be inserted if this circuit is not being used to ground the input to U6-B. These link options are used in conjunction with each other to set up the AD8022 (U6) dual op amp configuration to convert either a bipolar or unipolar single-ended signal into a differential signal centered on the common-mode voltage. Both links should be closed when the bipolar analog input signal biased around 0 V is applied to J19. Both links should be open when a unipolar analog input biased around 2.5 V is applied to J19. LK39 should be closed when this circuit is not being used. This link option selects the common-mode voltage applied to U6-A, the AD8022 dual op amp configuration used to perform single-ended-to-differential conversion on the analog input. In Position A, an external common-mode voltage can be applied to U6-A via J19. In Position B, the +IN input is tied to AGND, in which case the AD8022 dual op amp is not used. In Position C, a portion of VREF is applied to U6-A to set up the common-mode voltage. Not populated. This link option adds a 50 termination to AGND at the V3 DIFF socket (J20) for differential operation. This link is removed when using the single-ended-to-differential converter. When this link is inserted, a 50 termination is added to the input signal applied to the V3 DIFF socket (J20). This link should be inserted if this circuit is not being used to ground the input to U7-B. These link options are used in conjunction with each other to set up the AD8022 (U7) dual op amp configuration to convert either a bipolar or unipolar single-ended signal into a differential signal centered on the common-mode voltage. Both links should be closed when the bipolar analog input signal biased around 0 V is applied to J20. Both links should be open when a unipolar analog input biased around 2.5 V is applied to J20. LK42 should be closed when this circuit is not being used. This link option selects the common-mode voltage applied to U7-A, the AD8022 dual op amp configuration used to perform single-ended-to-differential conversion on the analog input. In Position A, an external common-mode voltage can be applied to U7-A via J21. In Position B, the +IN input is tied to AGND, in which case the AD8022 dual op amp is not used. In Position C, a portion of VREF is applied to U7-A to set up the common-mode voltage. Not populated. This link option adds a 50 termination to AGND at the V4 DIFF socket (J22) for differential operation. This link is removed when using the single-ended-to-differential converter. When this link is inserted, a 50 termination is added to the input signal applied to the V4 DIFF socket (J22). This link should be inserted if this circuit is not being used to ground the input to U8-B. These link options are used in conjunction with each other to set up the AD8022 (U8) dual op amp configuration to convert either a bipolar or unipolar single-ended signal into a differential signal centered on the common-mode voltage. Both links should be closed when the bipolar analog input signal biased around 0 V is applied to J22. Both links should be open when a unipolar analog input biased around 2.5 V is applied to J22. LK47 should be closed when this circuit is not being used. Rev. 0 | Page 6 of 24 EVAL-AD7265/AD7266 Link No. LK48 LK50 LK51 LK52 LK53 LK54 LK55 LK56 LK57 Description This link option selects the common-mode voltage applied to U8-A, the AD8022 dual op amp configuration used to perform single-ended-to-differential conversion on the analog input. In Position A, an external common-mode voltage can be applied to U8-A via J23. In Position B, the +IN input is tied to AGND, in which case the AD8022 dual op amp is not used. In Position C, a portion of VREF is applied to U8-A to set up the common-mode voltage. This link option sets the dc bias voltage level that is applied to the optional bias-up circuit used in single-ended mode. In Position A, the bias voltage is set to VREF/2. This configuration is used in 0 V to 2 VREF mode to set up the bias voltage for a bipolar single-ended signal. In Position B, the bias voltage is set to VREF/4. This configuration is used in 0 V to VREF mode to set up the bias voltage for a bipolar single-ended signal. This link option adds a 50 termination to AGND at the VIN A socket (J26) of the bias-up circuit for the single-ended input. When this link is inserted, a 50 termination is added to the input signal applied to the VIN A socket (J26). This link should be inserted if this circuit is not being used to ground the -IN input terminal of U10-A. This link option sets the dc bias voltage that is applied to the optional bias-up circuit used in single-ended mode. In Position A, the bias voltage is set to VREF/2. This configuration is used in 0 V to 2 VREF mode to set up the bias voltage for a bipolar single-ended signal. In Position B, the bias voltage is set to VREF/4. This configuration is used in 0 V to VREF mode to set up the bias voltage for a bipolar single-ended signal. This link option adds a 50 termination to AGND at the VIN B socket (J27) of the bias-up circuit for the single-ended input. When this link is inserted, a 50 termination is added to the input signal applied to the VIN B socket (J27). This link should be inserted if this circuit is not being used to ground the -IN input terminal of U11-B. Not populated. Not populated. This link option is used to select the source of the V- (-12 V) supply, which is used to power the op amps. In Position A, V- is supplied by the EVAL-CED1Z through the 96-way connector. In Position B, V- is supplied from an external source via the power connector, J30. This link option is used to select the source of the V+ (+12 V) supply, which is used to power the op amps. In Position A, V+ is supplied by the EVAL-CED1Z through the 96-way connector. In Position B, V+ is supplied from an external source via the power connector, J30. Rev. 0 | Page 7 of 24 EVAL-AD7265/AD7266 SETUP CONDITIONS Take care to ensure that all link positions are set according to the required operating mode before applying power and signals to the evaluation board. There are a few different modes in which to operate the evaluation board. Either the user can operate the board with the EVAL-CED1Z or it can be used as a standalone board. The board can accept differential and singleended analog input voltages. Table 2 shows the position in which all the links are set when the evaluation board is packaged. When the board is shipped, the assumption is that the user is operating with the EVAL-CED1Z. The links are set so that all power supplies and control signals are supplied by the EVAL-CED1Z. The board is configured for single-ended mode of operation on VA1 and VB1 with a 0 V to VREF input range. The AD780 provides an external reference voltage. If the differential mode of operation is required, the link positions must be configured as outlined in Table 4, Table 5, and Table 6. Table 2. Link Positions on the Packaged EVAL-AD7265/AD7266 (Single-Ended Mode of Operation, Channel VA1 and VB1 Selected) Link No. LK1 Position A LK2 C LK3 C LK4 C LK5 C LK6 C LK7 A LK8 C LK9 C LK10 C LK11 C LK12 C LK13 LK14 LK15 LK16 LK17 LK19 LK20 LK21 B B A Open A A B A LK22 LK23 LK24 LK25 LK27 LK28 LK29 LK31 LK32, LK34 B B C A B A A Closed Closed Function VA1 input is supplied from the output of the unity gain buffer U3-A. In this case, a unipolar signal must be applied to the SVIN1 socket via J13. VA2 input is tied to AGND. Once power supplies are applied to the ADC, this link can be changed to Position A if VA2 is to be converted. In this case, a unipolar signal should be applied to the SVIN2 SMB (J14). VA3 input is tied to AGND. Once power supplies are applied to the ADC, this link can be changed to Position A if VA3 is to be converted. In this case, a unipolar signal should be applied to the SVIN1 SMB (J13). VA4 input is tied to AGND. Once power supplies are applied to the ADC, this link can be changed to Position A if VA4 is to be converted. In this case, a unipolar signal should be applied to the SVIN2 SMB (J14). VA5 input is tied to AGND. Once power supplies are applied to the ADC, this link can be changed to Position A if VA5 is to be converted. In this case, a unipolar signal should be applied to the SVIN1 SMB (J13). VA6 input is tied to AGND. Once power supplies are applied to the ADC, this link can be changed to Position A if VA6 is to be converted. In this case, a unipolar signal should be applied to the SVIN2 SMB (J14). VB1 is supplied from the output of the unity gain buffer U4-A. In this case, a unipolar signal must be applied to the SVIN1 socket via J15. VB2 input is tied to AGND. Once power supplies are applied to the ADC, this link can be changed to Position A if VB2 is to be converted. In this case, a unipolar signal should be applied to the SVIN4 SMB (J16). VB3 input is tied to AGND. Once power supplies are applied to the ADC, this link can be changed to Position A if VB3 is to be converted. In this case, a unipolar signal should be applied to the SVIN3 SMB (J15). VB4 input is tied to AGND. Once power supplies are applied to the ADC, this link can be changed to Position A if VB4 is to be converted. In this case, a unipolar signal should be applied to the SVIN4 SMB (J16). VB5 input is tied to AGND. Once power supplies are applied to the ADC, this link can be changed to Position A if VB5 is to be converted. In this case, a unipolar signal should be applied to the SVIN3 SMB (J15). VB6 input is tied to AGND. Once power supplies are applied to the ADC, this link can be changed to Position A if VB6 is to be converted. In this case, a unipolar signal should be applied to the SVIN4 SMB (J16). The AD780 voltage reference provides a 2.5 V reference to the DCAPA pin. The AD780 voltage reference provides a 2.5 V reference to the DCAPB pin. The VDD supply (5 V) for the AD7265/AD7266 is provided by the EVAL-CED1Z. The AD780 reference voltage is set to output +2.5 V. The VDRIVE 3.3 V supply for the AD7265/AD7266 is provided by the EVAL-CED1Z. REF SELECT is tied to VDRIVE (Logic 1). The AD780 provides an external reference (2.5 V) to the AD7265/AD7266. RANGE is tied to DGND (Logic 0). The analog input range is 0 V to VREF. SGL/DIFF is tied to VDRIVE, enabling single-ended mode. If differential mode is required, then this link option should be in Position B. A0 is controlled by channel selection in the evaluation software. A1 is controlled by channel selection in the evaluation software. A2 is held low. This input must be changed manually by the user. CS is provided by the EVAL-CED1Z. SCLK is provided by the EVAL-CED1Z. Data from DOUTA is read by the EVAL-CED1Z. Data from DOUTB is read by the EVAL-CED1Z. The input to U5-B is tied to AGND because it is not used in single-ended mode. The inputs to U5-A are tied to AGND because they are not used in single-ended mode. Rev. 0 | Page 8 of 24 EVAL-AD7265/AD7266 Link No. LK33 LK36 LK37, LK39 LK38 LK41 LK42, LK44 LK43 LK46 LK47, LK49 LK48 LK50 LK51 LK52 LK53 LK56 LK57 Position B Closed Closed B Closed Closed B Closed Closed B B Open B Open A A Function The input to U5-A is tied to AGND because it is not used in single-ended mode. The input to U6-B is tied to AGND because it is not used in single-ended mode. The inputs to U6-A are tied to AGND because they are not used in single-ended mode. The input to U6-A is tied to AGND because it is not used in single-ended mode. The input to U7-B is tied to AGND because it is not used in single-ended mode. The inputs to U7-A are tied to AGND because they are not used in single-ended mode. The input to U7-A is tied to AGND because it is not used in single-ended mode. The input to U8-B is tied to AGND because it is not used in single-ended mode. The inputs to U8-A are tied to AGND because they are not used in single-ended mode. The input to U8-A is tied to AGND because it is not used in single-ended mode. The bias input for U12-A is set to VREF/4. Bias-up circuit is in use. The bias input for U12-B is set to VREF/4. Bias-up circuit is in use. V- is supplied by the EVAL-CED1Z. V+ is supplied by the EVAL-CED1Z. Table 3. Link Positions for Single-Ended Mode of Operation with a 0 V to 2 VREF Input Range When a Bipolar Single-Ended Signal Is Used Link No. LK20 LK21 LK50 LK51 LK52 LK53 Position A A A Open A Open Function RANGE is tied to VDRIVE (Logic 1). The analog input range is 0 V to 2 VREF. SGL/DIFF is tied to VDRIVE, enabling single-ended mode. The bias input for U12-A is set to VREF/2. Bias-up circuit is in use. The bias input for U12-B is set to VREF/2. Bias-up circuit is in use. Table 4. Link Positions for Differential Mode of Operation with a 0 V to VREF Input Range When a Bipolar Single-Ended Signal Is Used with the Single-Ended-to-Differential Converter Link No. LK1 Position B LK2 B LK20 LK21 LK31 LK32, LK34 LK33 B B Open Closed C Function VA1 is supplied from the positive output (V1+) of the single-ended-to-differential converter, U5-B, in which case a single-ended signal must be applied to V1 DIFF via Socket J17. VA2 is supplied from the negative output (V1-) of the single-ended-to-differential converter U5-A in which case a single-ended signal must be applied to V1 DIFF via Socket J17. The RANGE pin is tied to DGND (Logic 0). Therefore, the analog input range is 0 V to VREF. The ADC is tied to DGND and, therefore, the ADC is configured to operate in differential mode. The single-ended-to-differential converter, U5-B, is in use. These links should be closed when the bipolar analog input signal biased around 0 V is applied to J17. A portion of VREF is applied to U5-A to set up the common-mode voltage. Rev. 0 | Page 9 of 24 EVAL-AD7265/AD7266 Table 5. Link Positions for Differential Mode of Operation with a 0 V to 2 VREF Input Range When a Bipolar Single-Ended Signal Is Used with the Single-Ended-to-Differential Converter Link No. LK1 Position B LK2 B LK20 A LK21 LK31 LK32, LK34 LK33 B Open Closed C Function VA1 is supplied from the positive output (V1+) of the single-ended-to-differential converter, U5-B, in which case a single-ended signal must be applied to V1 DIFF via Socket J17. VA2 is supplied from the negative output (V1-) of the single-ended-to-differential converter, U5-A, in which case a single-ended signal must be applied to V1 DIFF via Socket J17. The RANGE pin is tied to VDRIVE (Logic 1). Therefore, the device is configured for an analog input range of 0 V to 2 VREF. The ADC is tied to DGND and, therefore, the ADC is configured to operate in differential mode. The single-ended-to-differential converter, U5-B, is in use. These links should be closed as the bipolar analog input signal biased around 0 V is applied to J17. A portion of VREF is applied to U5 to set up the common-mode voltage. Table 6. Link Positions for Differential Mode of Operation When a Unipolar Input Signal Is Used with the Single-Ended-toDifferential Converter Link No. LK1 Position B LK2 B LK21 LK31 LK32, LK34 LK33 LK50 B Open Open C A Function VA1 is supplied from the positive output (V1+) of the single-ended-to-differential converter, U5, in which case a single-ended signal must be applied to V1 DIFF via Socket J17. VA2 is supplied from the negative output (V1-) of the single-ended-to-differential converter, U5, in which case a single-ended signal must be applied to V1 DIFF via Socket J17. The ADC is tied to DGND and, therefore, the ADC is configured to operate in differential mode. The single-ended to differential converter, U5, is in use. These links should be open as the bipolar analog input signal biased around 2.5 V is applied to J17. A portion of VREF is applied to U5-A to set up the common-mode voltage. The bias input for U12-A is set to VREF/2. Rev. 0 | Page 10 of 24 EVAL-AD7265/AD7266 SOCKETS CONNECTORS There are 25 SMB input/output sockets relevant to the operation of the AD7265/AD7266 on this evaluation board. All of these sockets are used for applying an externally generated signal to the evaluation board or for accessing an output signal from the AD7265/ AD7266. When operating the board with the EVAL-CED1Z board, the only external sockets necessary are those used to supply the analog input signals to the ADC (that is, VA1 to VA6 and VB1 to VB6). All of the other sockets are optional and if they are not used, their signals are supplied by the EVAL-CED1Z. Most of these sockets are used when operating the board as a standalone unit because all the signals required are supplied from external sources. The functions of these sockets are outlined in Table 8. There are four connectors on the EVAL-AD7265/AD7266 as outlined in Table 7. Table 7. Connector Functions Connector J1 J2 J3 J30 Function 96-way connector for the digital interface and power supply connections External VDD power connector External VDRIVE power connector External +12 V, -12 V and AGND power connector Table 8. Socket Functions Reference Designator J5 J6 J7 J8 J9 J10 J11 J12 J13 J14 J15 J16 J17 Socket EXT COM2 A0 A1 A2 CS SCLK DOUTA DOUTB SVIN1 SVIN2 SVIN3 SVIN4 V1 DIFF J18 J19 EXT COM1 V2 DIFF J20 V3 DIFF J21 J22 EXT COM3 V4 DIFF J23 J24 EXT COM4 DCAPA J25 DACPB J26 J27 J28 J29 VIN A VIN B VBIASED-A VBIASED-B Function Subminiature BNC socket for an external common-mode voltage to be applied to U6. Subminiature BNC socket for an external A0 logic level. Subminiature BNC socket for an external A1 logic level. Subminiature BNC socket for an external A2 logic level. Subminiature BNC socket for an external CS signal. Subminiature BNC socket for an external SCLK input. Subminiature BNC socket for the DOUTA output. Subminiature BNC socket for DOUTB output. Subminiature BNC socket for a unipolar signal that is buffered by U3-A and applied to the ADC. Subminiature BNC socket for a unipolar signal that is buffered by U3-B and applied to the ADC. Subminiature BNC socket for a unipolar signal that is buffered by U4-A and applied to the ADC. Subminiature BNC socket for a unipolar signal that is buffered by U4-B and applied to the ADC. Subminiature BNC socket for a bipolar or unipolar single-ended input that is applied to the single-endedto-differential conversion circuit (U5-B). Subminiature BNC socket for an external common-mode voltage to be applied to U6. Subminiature BNC socket for a bipolar or unipolar single-ended input that is applied to the single-endedto-differential conversion circuit (U6-B). Subminiature BNC socket for a bipolar or unipolar single-ended input that is applied to the single-ended to-differential conversion circuit (U7-B). Subminiature BNC socket for an external common-mode voltage to be applied to U7. Subminiature BNC socket for a bipolar or unipolar single-ended input that is applied to the single-ended to-differential conversion circuit (U8-B). Subminiature BNC socket for an external common-mode voltage applied to U8. Subminiature BNC socket for an external reference voltage to be applied to DCAPA or to access the internal reference from the AD7265/AD7266. Subminiature BNC socket for an external reference voltage to be applied to DCAPB or to access the internal reference from the AD7265/AD7266. Subminiature BNC socket for a bipolar single-ended input to be applied to Bias-Up Circuit A. Subminiature BNC socket for a bipolar single-ended input to be applied to Bias-Up Circuit B. Output from Bias-Up Circuit A, which can be applied to SVINx for single-ended mode of operation. Output from Bias-Up Circuit B, which can be applied to SVINx for single-ended mode of operation. Rev. 0 | Page 11 of 24 EVAL-AD7265/AD7266 INTERFACING THE EVALUATION BOARD TO THE EVAL-CED1Z 1 8 16 24 32 1 8 16 24 32 A B C 07921-002 Interfacing the EVAL-CED1Z board to the evaluation board is via a 96-way connector, J1. The pinout for the J1 connector is shown in Figure 2. Table 9 gives a description of the pins on the 96-way connector that are used to interface the EVAL-CED1Z to the EVAL-AD7265/AD7266. Figure 2. Pin Configuration for the 96-Way Connector, J1 Table 9. The 96-Way Connector Pin Description Signal DR1PRI DR0SEC RSCLK0 TFS0 RFS0 VDD VDRIVE -5 V DGND AGND +12 V -12 V FL0 GPIO3 Description Data receive primary. This input is connected to the DOUTA pin of the AD7265/AD7266. Data receive secondary. This input is connected to the DOUTB pin of the AD7265/AD7266. Receive clock. This continuous clock is connected to the SCLK pin of the AD7265/AD7266 via LK27. Transmit frame sync. This output is connected to the CS pin of the AD7265/AD7266 via LK25 to frame the serial data transfer. Receive frame sync. This input is connected to the TFS pin on the EVAL-CED1Z to frame the serial data read. Analog +5 V supply. These lines are connected to the VDD line on the board via LK15. Digital +3.3 V supply. This is used to provide the VDRIVE supply to the board via LK17 for the digital logic. Analog -5 V supply. This supply is not used on the EVAL-AD7265/AD7266. Digital ground. These lines are connected to the digital ground plane on the evaluation board. Analog ground. These lines are connected to the analog ground plane on the evaluation board. +12 V supply (VCC). This line is connected to the +12 V supply line on the board via LK57. -12 V supply (VSS). This line is connected to the -12 V supply line on the board via LK56. Flag zero. This output is connected to the A0 pin of the AD7265/AD7266 via LK22. General-purpose input/output. This input is connected to the A1 pin of the AD7265/AD7266 via LK23. Table 10. 96-Way Connector Pin Functions1 Pin 1 2 3 4 Row A DT1PRI TFS1 TSCLK1 DGND 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 1 DGND Row C DR1PRI RFS1 RSCLK1 DGND DT0PRI TFS0 TSCLK0 VDRIVE (+3.3 V) VDRIVE (+3.3 V) DR0PRI RFS0 RSCLK0 VDRIVE (+3.3 V) DT0SEC DGND DGND GPIO5 GPIO0 DGND FL0 DGND AGND AGND AGND AGND AGND AGND AGND -12 V -5 V VDD (+5 V) Row B GPIO3 DGND GPIO1 DGND AGND AGND AGND AGND AGND AGND AGND AGND AGND AGND -5 V VDD (+5 V) GPIO6 DGND DR0SEC GPIO7 GPIO4 DGND GPIO2 DGND AGND AGND AGND AGND AGND AGND AGND +12 V -5 V VDD (+5 V) The unused pins of the 96-way connector are not shown. TEST POINTS There are two test points on the inputs to the AD7265/AD7266 on the evaluation board. Test points enable the user to have easy access to various signals on the EVAl-AD7265/AD7266, facilitating probing, evaluation, and debugging. Rev. 0 | Page 12 of 24 EVAL-AD7265/AD7266 OPERATING WITH THE EVAL-CED1Z The evaluation board can be operated in a standalone mode or it can be operated in conjunction with the EVAL-CED1Z. This evaluation board controller is available from Analog Devices under the order entry, EVAL-CED1Z. When interfacing the EVAL-AD7265/AD7266 directly to the EVAL-CED1Z board, all supplies and control signals to operate the AD7265/AD7266 board are provided by the EVAL-CED1Z. The AD7266 can operate at 2 MSPS with SCLK frequencies up to 32 MHz, and the AD7265 can operate with a 16 MHz SCLK to give a 1 MSPS throughput. The SCLK frequency supplied by the EVAL-CED1Z is fixed at 32 MHz for the AD7266. The software allows the user to change the throughput rate by effectively modifying the CS high time. Software to communicate with the EVAL-CED1Z and AD7265/AD7266 is provided with the AD7266/AD7266 evaluation board package. The 96-way connector on the EVAL-AD7265/AD7266 plugs directly into the 96-way connector on the EVAL-CED1Z. The evaluation board is powered from a 7 V, 15 W power supply that accepts input voltages from 100 V to 240 V ac, and contains the relevant adaptors for worldwide use. Connection between the EVAL-CED1Z and the USB port of a PC is via a standard USB 2.0 connection cable that is provided as part of the EVAL-CED1Z package. Rev. 0 | Page 13 of 24 EVAL-AD7265/AD7266 EVALUATION BOARD SOFTWARE INSTALLING THE SOFTWARE SETTING UP THE EVAL-CED1Z The EVAL-AD7265/AD7266 evaluation kit includes self-installing software on a CD-ROM for controlling and evaluating the performance of the AD7265/AD7266 when it is operated with the EVAL-CED1Z board. The software is compatible with Windows(R) 2000/XP(R). If the setup file does not run automatically, setup.exe can be run from the CD-ROM. This section describes how the evaluation board, the EVAL-CED1Z, and the software should be set up to begin using the complete system. When the CD is inserted into the PC, an installation program automatically begins. This program installs the evaluation software. The user interface on the PC is a dedicated program written especially for the AD7265/AD7266 when operating with the EVAL-CED1Z board. Install the software before the USB cable is connected between the EVAL-CED1Z and the PC. This ensures that the appropriate USB driver files have been properly installed before the EVALCED1Z is connected to the PC. When the software is run for the first time with the EVAL-CED1Z connected to the PC, the PC automatically finds the new device and identifies it. Follow the onscreen instructions that appear automatically. This installs the drivers for the EVAL-CED1Z on the PC. If an error appears onscreen when the software is first opened, then the PC is not recognizing the USB device. To correct this error, 1. 2. 3. 4. 5. 1. 2. 3. 4. 5. Install the AD7265/AD7266 evaluation board software. Connect the EVAL-CED1Z and the evaluation board together via the 96-way connector. Apply power to the EVAL-CED1Z via the provided 7 V, 15 W power supply. At this stage, the green LED labeled Power on the EVAL-CED1Z should light up, which indicates that the EVAL-CED1Z is receiving power. Connect the USB cable between the PC and the EVAL-CED1Z. A green LED positioned beside the USB connector on the EVAL-CED1Z lights up, indicating that the USB connection has been established. The EVAL-AD7265/AD7266 are detected. Proceed through any dialog boxes that may appear (use the recommended options) to finalize the installation. Start the EVAL-AD7265/AD7266 software. The FPGA on the EVAL-CED1Z is automatically programmed when the software is opened. The two red LEDs (D14 and D15) on the EVAL-CED1Z now light up. This indicates that the EVAL-CED1Z is functional and ready to receive instructions. Right-click the My Computer icon, then select Properties. When the System Properties window opens, select the Hardware tab. Click Device Manager in the Hardware Tab of the System Properties window. Examine the devices listed under the Universal Serial Bus Controller heading. If an unknown device is listed, right-click this option and select Update Driver. The New Hardware Wizard runs twice. Under ADI Development Tools, the hardware is listed as ADI Converter Evaluation and Development Board (WF). Reboot your PC. Rev. 0 | Page 14 of 24 EVAL-AD7265/AD7266 SOFTWARE OPERATION With the hardware set up, you can now use the software to control the EVAL-CED1Z and the AD7266 or AD7265 evaluation board. To launch the software, from the Analog Devices menu, select the AD7266/AD7265 submenu, and then click the AD7266/AD7265 icon. Figure 3 shows the window that appears when the software is run. The main function of this window is to allow you to read a predetermined number of samples from the evaluation board and display them in both the time and frequency domain. The window can be divided into three main sections: Part Information, Data Capture, and Linearity. The menu bar is located at the top portion of the window, with the Part Information panel on the left-hand side of the window. The Data Capture and Linearity tabs are in the center. The Data Capture tab consists of four subtabs: Waveform, Histogram, FFT, and Summary. The Linearity tab, which enables you to generate a linearity plot for the device, consists of three subtabs: Histogram, INL, and DNL. 07921-003 Figure 3 displays the main window that is opened. If an error message appears, click OK and restart the application after checking the connection between the adapter board and the USB port on the PC. Also check that the USB device is identified by the Device Manager as detailed in the Installing the Software Section. The software that controls the EVAL-CED1Z and, therefore, the AD7265/AD7266 evaluation board, has two main windows. Figure 3. AD7266 Main Window Rev. 0 | Page 15 of 24 EVAL-AD7265/AD7266 USING THE SOFTWARE samples taken, for example, the minimum/maximum position or velocity, the spread, the standard deviation, and the mean. Menu Bar The menu bar consists of the following menus: File, Edit, Operate, Tools, Window, and Help. Part Information Panel The Part Information panel allows you to select the following configuration options: * * * * * The part number box allows you to select the part being tested by typing in the appropriate part number, either AD7265 or AD7266. Sampling Rate allows you to set the sampling frequency. The maximum sampling frequency supported by the EVAL-AD7265/AD7266 is 1.4 MSPS for the AD7266 and 1 MSPS for the AD7265. Input Mode allows you to select from single-ended, differential, or pseudodifferential mode. Input Channel Selection allows you to select the pair of channels for conversion. This channel selection option must be used in conjunction with LK24 on the board. Alternatively, LK22, LK23, and LK24 can be used instead to select the channels for conversion in the hardware, in which case this option is not used. Voltage Span allows you to select between 0 V to VREF and 0 V to 2 VREF mode of operation. * Histogram Tab The Histogram tab displays a histogram of the captured ADC codes. It can be used to give an indication of the ADC's performance in response to dc inputs. The Histogram Analysis section contains information about the samples taken, for example, maximum and minimum codes captured. FFT Tab This tab displays a fast Fourier transform (FFT) plot. The FFT is typically used for examining the ADC's performance in the frequency domain. The Spectrum Analysis section contains information about the samples taken, for example, ac specifications. You can choose whether to display the information for ADC A, or ADC B, or both in the window using the ADC A ON/OFF and ADC B ON/OFF buttons, as explained in the Waveform Tab section. Summary Tab The Part Information tab also provides the following information: * The waveform graph displays the information for both ADC A and ADC B, or either ADC as desired. Two buttons located on the bottom right-hand side of the graph, labeled ADC A ON/OFF and ADC B ON/OFF are used to select which ADC's data is displayed. An indicator, located on the top right-hand corner of the graph, shows what color graph represents each ADC when the data from both ADCs is displayed. Resolution. The software automatically sets the resolution at 12 bits. Data Format. The software automatically sets the data output format to straight binary or twos complement. The Part Information tab also includes a Busy status indicator that lights when the evaluation board is busy, and an Exit button that allows you to quit the program. Data Capture Tab In the Data Capture tab, you can select the number of samples to be captured from the # Samples drop-down box. The default number of samples is 4096; you are free to change this as required. The desired display option is selected by clicking one of the Waveform, Histogram, or FFT tabs. Waveform Tab The Waveform subtab displays a digital storage oscilloscope (DSO) that allows you to display a waveform. When samples are uploaded from the EVAL-CED1Z board, they are displayed here. The samples are displayed as integer code values. At the bottom left of the graph are the zoom options. These allow you to zoom in and out for a closer look at a sample, if required. The Waveform Analysis section, which is located beneath the waveform graph, contains information about the This tab shows a summary of the information displayed in each of the discrete tabs; that is, the waveform, histogram and FFT plots. Linearity Tab In the Linearity tab, you can select the number of hits per code to be captured for the linearity analysis. The desired display option is selected by clicking the Histogram, INL, DNL, or Summary tabs. To initiate the data collection, click the Get Linearity Data button. The data collection and analysis takes a few seconds to complete. The greater the number of hits per code selected, the longer the analysis takes. Histogram Tab The Histogram tab displays a histogram of the captured ADC codes. It can be used to give an indication of the ADC's performance in response to dc inputs. The Histogram Analysis section contains information about the samples taken, for example, maximum and minimum codes captured. INL Tab The INL tab displays an INL plot for the AD7266 or AD7265. This plot can be used to examine the dc performance of the ADC. The Linearity Analysis section contains information on the maximum and minimum INL error and the code at which this error occurred. It also shows the total number of hits per code and the number of samples taken. Rev. 0 | Page 16 of 24 EVAL-AD7265/AD7266 DNL Tab The DNL tab displays a DNL plot for the AD7266 or AD7265. This plot can be used to examine the dc performance of the ADC in conjunction with the INL plot. The Linearity Analysis section contains information on the maximum and minimum DNL error and the code at which this error occurred. TAKING SAMPLES To initiate a conversion and capture the sample data, you must click the Sample button or the Continuous button. Both the Sample and the Continuous buttons are located on the top right-hand corner of the Data Capture tab. When you click the Sample button, the software instructs the EVAL-CED1Z to take the required number of samples at the required frequency from the evaluation board. The AD7266 evaluation board runs with a sampling speed less than or equal to 2 MSPS, and the AD7265 evaluation board runs with a sampling speed less than 1 MSPS. You can choose the sampling frequency up to this rate and the number of samples to be taken. The samples taken are then uploaded and displayed. An FFT and/or histogram can be calculated and displayed. If you click the Continuous button, the software repeats the process indefinitely until you click Stop. (The Continuous button switches to Stop when clicked). You can switch between displaying data from ADC A, ADC B, or both while the software is running continuously. Rev. 0 | Page 17 of 24 EVAL-AD7265/AD7266 EVALUATION BOARD SCHEMATICS AND ARTWORK 07921-004 EVAL-AD7265/AD7266 schematics, silkscreen, and layout can be found in Figure 4 to Figure 9. Figure 4. AD7265/AD7266 Evaluation Board Circuit Diagram 1 Rev. 0 | Page 18 of 24 07921-005 EVAL-AD7265/AD7266 Figure 5. AD7265/AD7266 Evaluation Board Circuit Diagram 2 Rev. 0 | Page 19 of 24 07921-006 EVAL-AD7265/AD7266 Figure 6. AD7265/AD7266 Evaluation Board Circuit Diagram 3 Rev. 0 | Page 20 of 24 07921-007 EVAL-AD7265/AD7266 07921-008 Figure 7. AD7265/AD7266 Evaluation Board PCB Layout--Component Side Figure 8. AD7265/AD7266 Evaluation Board PCB Layout--Solder Side Rev. 0 | Page 21 of 24 07921-009 EVAL-AD7265/AD7266 Figure 9. AD7265/AD7266 Evaluation Board PCB Layout--Silkscreen Rev. 0 | Page 22 of 24 EVAL-AD7265/AD7266 ORDERING INFORMATION BILL OF MATERIALS Table 11. Qty 6 12 16 1 Reference Designator R17, R25, R33, R41, R47, R54 R1 to R12 R14 to R16, R18, R22 to R24, R26, R30 to R32, R34, R38 to R40, R42 R13, R21, R29, R37 R45, R46, R48, R50 to R53, R55, R57 to R60 R49, R56 R20, R28, R36, R44 R19, R27, R35, R43 C33 to C36 C1 to C12 C13, C14 C16, C17, C20, C21, C23, C26, C30, C37, C44 to C50, C53, C54, C59, C60, C63 to C67, C72, C74, C76, C78, C80 C15, C18, C19, C22, C27, C31, C38 to C43, C51, C52, C55 to C58, C61, C62, C68 to C71, C73, C75, C77, C79 U1 1 9 1 57 1 2 U2 U3 to U8 and U10 to U12 D1 LK1 to LK57 J1 J2, J3 1 J30 25 J5 (EXT COM2), J6 (A0), J7 (A1), J8 (A2), J9 (CS), J10 (SCLK), J11 (DOUTA), J12 (DOUTB), J13 (SVIN1), J14 (SVIN2), J15 (SVIN3), J16 (SVIN4), J17 (V1 DIFF), J18 (EXT-COM1), J19 (V2 DIFF), J20 (V3 DIFF), J21 (EXT COM3), J22 (V4 DIFF), J23 (EXT COM4), J24 (DCAPA), J25 (DCAPB), J26 (VIN A), J27 (VIN B), J28 (VBIASED-A), J29 (VBIASED-B) T1, T4 4 12 2 4 4 4 12 2 29 28 2 1 Supplier/Number 1 FEC 9331336 FEC 9331433 FEC 9330801 390 resistor 1 k resistor 3 k resistor 10 k resistor 20 resistor 68 pF capacitor 1 nF capacitor 470 nF capacitor 0.1 F capacitor FEC 9331131 FEC 9330380 FEC 9330976 FEC 9330399 FEC 9330771 FEC 722-066 FEC 722-170 FEC 318-8851 FEC 432-210 10 F, 10 V capacitor FEC 197-130 AD7266 or AD7265 ADC Analog Devices AD7266BSUZ, AD7265BSUZ Analog Devices AD780ARZ Analog Devices AD8022ARZ Digi-Key SD103CTPMSCT-ND FEC 1022244 FEC 1096832 FEC 3041359 AD780 reference AD8022 op amp 20 V Schottky diode Jumper 96-way connecter, CON\41612\96 Terminal block, 2-way power connector Terminal block, 3-way power connector SMB connector FEC 1111349 Test points FEC 8731144 FEC refers to Farnell Electronics. ESD CAUTION ORDERING GUIDE Model EVAL-AD7265EDZ1 EVAL-AD7266EDZ1 EVAL-CED1Z1 1 Description 51 resistor 62 resistor 220 resistor Description Evaluation Board for AD7265 Evaluation Board for AD7266 Controller Board Z = RoHS Compliant Part. Rev. 0 | Page 23 of 24 FEC 3041360 EVAL-AD7265/AD7266 NOTES (c)2009 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. EB07921-0-4/09(0) Rev. 0 | Page 24 of 24