SPECIFICATION
MODEL
RATED CURRENT
RATED POWER
OUTPUT
CURRENT ADJ. RANGE
SETUP, RISE TIME
HOLD UP TIME (Typ.)
VOLTAGE RANGE Note.2
FREQUENCY RANGE
POWER FACTOR (Typ.)
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INPUT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
SAFETY STANDARDS Note.3
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVER TEMPERATURE
OVER VOLTAGE
Can be adjusted by internal potentiometer (A type only)
16ms at full load 230VAC / 115VAC
1000ms, 80ms / 115VAC at full load 500ms, 80ms / 230VAC at full load
90 ~ 305VAC 127VDC ~ 431VDC
47 ~ 63Hz
1.6A / 115VAC 0.8 A / 230VAC 0.7A / 277VAC
<0.75mA / 277VAC
-40 ~ +70 (Refer to "Derating Curve")℃
10 ~ 95% RH non-condensing
-40 ~ +80 , 10 ~ 95% RH℃
±℃ ℃0.03%/ (0 ~ 50 )
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
RIPPLE CURRENT
ENVIRONMENT
SAFETY &
EMC
PROTECTION
475 ~ 495V
Protection type : Shut down o/p voltage with auto-recovery or re-power on to recovery
SHORT CIRCUIT
94%
PF>0.98/115VAC, PF>0.96/230VAC, PF>0.93/277VAC at full load (Please refer to "Power Factor Characteristic" curve)
HLG-120H-C350 HLG-120H-C500 HLG-120H-C700 HLG-120H-C1050 HLG-120H-C1400
±5%
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃
2. Derating may be needed under low input voltages. Please check the static characteristics for more details.
3. Safety and EMC design refer to EN60598-1, CNS15233, GB7000.1.
4. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
5. Refer to warranty statement.
6. Please refer to "DRIVING METHODS OF LED MODULE".
7. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently
connected to the mains.
Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547 light, industry level (surge L,N-FG: 4KV), criteria A
UL8750, CSA C22.2 No. 250.12-13, ENEC EN61347-1, EN61347-2-13, EN62384 independent, IP65 or IP67 approved
175 ~ 350mA 250 ~ 500mA
±1%
350 ~ 700mA
±1%
525 ~ 1050mA
±1%
700 ~ 1400mA
±1%
350mA
150.5W
215 ~ 430V 150V ~ 300V 107V ~ 215V 74V ~ 148V 54V ~ 108V
I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH℃
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
335 ~ 355V
94%
240 ~ 260V
94%
165 ~ 175V
94%
120 ~ 130V
93.5%
500mA 700mA 1050mA 1400mA
150W 150.5W 155.4W 151.2W
■ Features :
A : IP65 rated. Constant current level can be adjusted through internal potentiometer.
B : IP67 rated. Constant current level adjustable through output cable with 1~10Vdc or 10V PWM signal or resistance.
D (option) : IP67 rated. Timer dimming function, contact MEAN WELL for details.
Constant current design
Universal AC input / Full range (up to 305VAC)
Built-in active PFC function
High efficiency up to 94%
Protections: Short circuit / Over voltage / Over temperature
Cooling by free air convection
Output current adjustable through output cable or internal potentiometer
IP67 / IP65 design for indoor or outdoor installations
Three in one dimming function (1~10Vdc or 10V PWM signal or resistance)
Suitable for dry / damp / wet locations
5 years warranty (Note.5)
FMM
110
IP65 IP67
HLG-120H-C350 A
150W Single Output LED Power Supply HLG-120H-C series
File Name:HLG-120H-C-SPEC 2015-05-11
EMC IMMUNITY
EMC EMISSION
CURRENT ACCURACY ±5.0%
Compliance to EN55015, EN61000-3-2 Class C ( 50% load) ; EN61000-3-3≧
CONSTANT CURRENT REGION
Note.6
RIPPLE & NOISE
2Vp-p 1.5Vp-p 1Vp-p 1Vp-p 1Vp-p
191.1K hrs min. MIL-HDBK-217F (25 )℃
220*68*38.8mm (L*W*H)
1.04Kg; 12pcs/13.5Kg/0.8CUFT
LINE REGULATION ±1%
COLD START 50A(t =600 s measured at 50% I ) at 230VAC
width peak
μ
Shut down o/p voltage, recovers automatically after temperature goes down
Constant current limiting, recovers automatically after fault condition is removed
TOTAL HARMONIC DISTORTION
THD< 20% when output loading 50% at 115VAC/230VAC input and output loading 75% at 277VAC input≧≧
MAX. No. of PSUs on 16A
CIRCUIT BREAKER 4 units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230VAC
Mechanical Specification Case No.994 Unit:mm
A Type:(HLG-120H-C_A)
※IP65 rated. Output voltage and constant current level can be adjusted through internal potentiometer.
(Can access by removing the rubber stopper on the case.)
300 20±
SJTW 16AWG 3C×
220
196
12
9.6
9.49.4 34.2
68
300 20±
+V(Red)
DIM+(Blue)
-V(Black)
DIM-(White)
FG (Green/Yellow)
AC/L(Brown)
AC/N(Blue)
B Type:(HLG-120H-C_B)
SJTW 16AWG 2C×
98
Tcase
34
※T case: Max. Case Temperature.
D Type(option):(HLG-120H-C_D)
※IP67 rated. Timer dimming function, contact MEAN WELL for details.
300 20±
300 20±
FG (Green/Yellow)
FG (Green/Yellow)
STW 16AWG 2C(for HLG-120H-C350)×
SJTW 16AWG 2C(for others)×
STW 16AWG 2C(for HLG-120H-C350)×
SJTW 16AWG 2C(for others)×
STW 16AWG 2C(for HLG-120H-C350)×
SJTW 16AWG 2C(for others)×
38.8
SJTW 16AWG 3C×
SJTW 16AWG 3C×
220
220
196
196
AC/L(Brown)
AC/L(Brown)
AC/N(Blue)
AC/N(Blue)
12
12
9.6
9.6
9.4
9.4 9.4
9.4 34.2
34.2
68
68
ψ×4.2 4PL
ψ×4.2 4PL
ψ×4.2 4PL
300 20±
300 20±
+V(Red)
+V(Red)
-V(Black)
-V(Black)
98
98
Tcase
Tcase
34
34
※T case: Max. Case Temperature.
※T case: Max. Case Temperature.
Io
ADJ.
38.8
38.8
150W Single Output LED Power Supply HLG-120H-C series
File Name:HLG-120H-C-SPEC 2015-05-11
0.84
0.86
0.88
0.9
0.92
0.94
0.96
0.98
1
50% 60% 70% 80% 90% 100%
277V
230V
115V
Derating Curve Static Characteristics
INPUT VOLTAGE (V) 60Hz
90 100 125 135 145 155 165 175 180 200 230 305
100
90
80
70
60
50
40
LOAD (%)
DIM+
(B Type)
DIM-
DETECTION
PWM & PFC CIRCUIT
O.L.P.O.T.P.
EMI FILTER
RECTIFIERS
POWER
SWITCHING
FILTER
&
RECTIFIERS +V
-V
I/P
FG
CONTROL
O.V.P.
&
O.L.P.
PFC
CIRCUIT
Block Diagram
PFC fosc : 70KHz
PWM fosc : 60KHz
Power Factor Characteristic
PF
LOAD
Constant Current Mode
(150W)
AMBIENT TEMPERATURE ( )
℃
LOAD (%)
(HORIZONTAL)
-40 0-10-20 15 30 50 60 70
20
40
60
80 Others
C500,C700
100
150W Single Output LED Power Supply HLG-120H-C series
File Name:HLG-120H-C-SPEC 2015-05-11
74
77
80
83
86
89
92
95
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
277V
230V
115V
HLG-120H-C series possess superior working efficiency that up to 94% can be reached in field applications.
LOAD
EFFICIENCY (%)
EFFICIENCY vs LOAD (HLG-120H-C700A Model)
DRIVING METHODS OF LED MODULE
A typical LED power supply may work in "constant current mode (CC)" to drive the LEDs.
Mean Well's LED power supply with CC characteristic can be operated at CC mode (direct drive).
In the constant current region, the highest voltage at the output of the driver
depends on the configuration of the end systems.
Should there be any compatibility issues, please contact MEAN WELL.
Typical LED power supply I-V curve
Vo(%)
100
50 100 Io (%)
Constant
Current region
150W Single Output LED Power Supply HLG-120H-C series
File Name:HLG-120H-C-SPEC 2015-05-11
HLG-120H-C
BType
DIMMING OPERATION
+V(Red)
DIM+(Blue)
-V(Black)
DIM-(White)
FG (Green/Yellow)
AC/L(Brown)
AC/N(Blue)
Dimming connection diagram for turning the lighting fixture ON/OFF :
Using a switch and relay can turn ON/OFF the lighting fixture.
※Using the built-in dimming function on B-type model can't turn the lighting fixture totally dark. Please refer to the connection method below to
achieve 0% brightness of the lighting fixture connecting to the LED power supply unit.
※Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.
1.Output constant current level can be adjusted through output cable by connecting a or 1~10Vdc or 10V PWM signal between DIM+ and DIM-.resistance
2.The LED lighting fixture can be turned ON/OFF by the switch.
※Reference resistance value for output current adjustment (Typical)
※Built-in 3 in 1 dimming function, IP67 rated. Output constant current level can be adjusted through output cable by connecting a resistance or
1 ~ 10Vdc or 10V PWM signal between DIM+ and DIM-.
※Please DO NOT connect "DIM-" to "-V".
NFG L
Relay
Blue
Brown
Green/
Yellow AC/L
AC/N
HLG-120H-C
BType
DIM+
DIM-
V(-)
V(+)
Blue
White
Black
Red
Switch Adjuster
10K~100K Ohms resistance
1~10V DC Voltage
10V PWM Signal
LED Lighting Fixture
102%~108%
102%~108%
102%~108%
※10V PWM signal for output current adjustment (Typical): Frequency range :100Hz ~ 3KHz
60%
1V 4V 7V2V 5V 8V3V 6V 9V 10V
10% 20% 30% 40% 50% 70% 80%
OPEN
OPEN
90% 100%
Dimming value
Percentage of rated current
※1 ~ 10V dimming function for output current adjustment (Typical)
60%
60%
10%
10%
20%
20%
30%
30%
40%
40%
50%
50%
70%
70%
80%
80%
90%
90%
100%
100%
Duty value
Percentage of rated current
60KΩ
60%
10KΩ
10K /NΩ20K /NΩ30K /NΩ40K /NΩ50K /NΩ60K /NΩ70K /NΩ80K /NΩ90K /NΩ
100K /N
Ω
Single driver
Multiple drivers
(N=driver quantity for synchronized
dimming operation)
10%
20KΩ
20%
30KΩ
30%
40KΩ
40%
50KΩ
50%
70KΩ
70%
80KΩ
80%
90KΩ100KΩOPEN
90% 100%
Resistance
value
Percentage of rated current
-----
150W Single Output LED Power Supply HLG-120H-C series
File Name:HLG-120H-C-SPEC 2015-05-11
◎Waterproof connector
Waterproof connector can be assembled on the output cable of HLG-120H-C to operate in dry/wet/damp or outdoor environment.
HLG-120H-C
I/P
LED Lamp
AC
source
◎Cable Joiner
Pin Configuration (Female) Pin Configuration (Female)
Size Size
M12 M15
4-PIN
5A/PIN
M12-04Order No. Order No.
10A max.Suitable Current Suitable Current
5-PIN
5A/PIN
M12-05
10A max.
2-PIN
12A/PIN
M15-02
12A max.
Up to four wires can be connected through this cable joiner by
soldering or clamping by tools.
66
26 20
ψ25
CJ04-2 suitable for 18AWG~22AWG
CJ04-1 suitable for 14AWG~16AWG
LED Lamp
HLG-120H-C
WATERPROOF CONNECTION
※CJ04 cable joiner can be purchased independently for user's own assembly.
MEAN WELL order No. : CJ04-1, CJ04-2.
O/P
O/P Wires
150W Single Output LED Power Supply HLG-120H-C series
File Name:HLG-120H-C-SPEC 2015-05-11
