Philips Semiconductors Product specification
Triacs BT136X series
GENERAL DESCRIPTION QUICK REFERENCE DATA
Passivated triacs in a full pack plastic SYMBOL PARAMETER MAX. MAX. UNIT
envelope, intended for use in
applications requiring high BT136X- 600 800
bidirectional transient and blocking BT136X- 600F
voltage capability and high thermal
cycling performance. Typical VDRM Repetitive peak off-state 600 800 V
applications include motor control, voltages
industrial and domestic lighting, IT(RMS) RMS on-state current 4 4 A
heating and static switching. ITSM Non-repetitive peak on-state 25 25 A
current
PINNING - SOT186A PIN CONFIGURATION SYMBOL
PIN DESCRIPTION
1 main terminal 1
2 main terminal 2
3 gate
case isolated
LIMITING VALUES
Limiting values in accordance with the Absolute Maximum System (IEC 134).
SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT
-600 -800
VDRM Repetitive peak off-state - 6001800 V
voltages
IT(RMS) RMS on-state current full sine wave; Ths ≤ 92 ˚C - 4 A
ITSM Non-repetitive peak full sine wave; Tj = 25 ˚C prior to
on-state current surge
t = 20 ms - 25 A
t = 16.7 ms - 27 A
I2tI
2t for fusing t = 10 ms - 3.1 A2s
dIT/dt Repetitive rate of rise of ITM = 6 A; IG = 0.2 A;
on-state current after dIG/dt = 0.2 A/µs
triggering T2+ G+ - 50 A/µs
T2+ G- - 50 A/µs
T2- G- - 50 A/µs
T2- G+ - 10 A/µs
IGM Peak gate current - 2 A
VGM Peak gate voltage - 5 V
PGM Peak gate power - 5 W
PG(AV) Average gate power over any 20 ms period - 0.5 W
Tstg Storage temperature -40 150 ˚C
TjOperating junction - 125 ˚C
temperature
T1T2
G
123
case
1 Although not recommended, off-state voltages up to 800V may be applied without damage, but the triac may
switch to the on-state. The rate of rise of current should not exceed 3 A/µs.
June 2001 1 Rev 1.400
Philips Semiconductors Product specification
Triacs BT136X series
ISOLATION LIMITING VALUE & CHARACTERISTIC
Ths = 25 ˚C unless otherwise specified
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Visol R.M.S. isolation voltage from all f = 50-60 Hz; sinusoidal - - 2500 V
three terminals to external waveform;
heatsink R.H. ≤ 65% ; clean and dustfree
Cisol Capacitance from T2 to external f = 1 MHz - 10 - pF
heatsink
THERMAL RESISTANCES
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Rth j-hs Thermal resistance full or half cycle
junction to heatsink with heatsink compound - - 5.5 K/W
without heatsink compound - - 7.2 K/W
Rth j-a Thermal resistance in free air - 55 - K/W
junction to ambient
STATIC CHARACTERISTICS
Tj = 25 ˚C unless otherwise stated
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
BT136X- ... ...F
IGT Gate trigger current VD = 12 V; IT = 0.1 A
T2+ G+ - 5 35 25 mA
T2+ G- - 8 35 25 mA
T2- G- - 11 35 25 mA
T2- G+ - 30 70 70 mA
ILLatching current VD = 12 V; IGT = 0.1 A
T2+ G+ - 7 20 20 mA
T2+ G- - 16 30 30 mA
T2- G- - 5 20 20 mA
T2- G+ - 7 30 30 mA
IHHolding current VD = 12 V; IGT = 0.1 A - 5 15 15 mA
VTOn-state voltage IT = 5 A - 1.4 1.70 V
VGT Gate trigger voltage VD = 12 V; IT = 0.1 A - 0.7 1.5 V
VD = 400 V; IT = 0.1 A; 0.25 0.4 - V
Tj = 125 ˚C
IDOff-state leakage current VD = VDRM(max); - 0.1 0.5 mA
Tj = 125 ˚C
June 2001 2 Rev 1.400
Philips Semiconductors Product specification
Triacs BT136X series
DYNAMIC CHARACTERISTICS
Tj = 25 ˚C unless otherwise stated
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
BT136X- ... ...F
dVD/dt Critical rate of rise of VDM = 67% VDRM(max); 100 50 250 - V/µs
off-state voltage Tj = 125 ˚C; exponential
waveform; gate open
circuit
dVcom/dt Critical rate of change of VDM = 400 V; Tj = 95 ˚C; - - 50 - V/µs
commutating voltage IT(RMS) = 4 A;
dIcom/dt = 1.8 A/ms; gate
open circuit
tgt Gate controlled turn-on ITM = 6 A; VD = VDRM(max);- - 2-µs
time IG = 0.1 A; dIG/dt = 5 A/µs
June 2001 3 Rev 1.400
Philips Semiconductors Product specification
Triacs BT136X series
Fig.1. Maximum on-state dissipation, Ptot, versus rms
on-state current, IT(RMS), where α = conduction angle.
Fig.2. Maximum permissible non-repetitive peak
on-state current ITSM, versus pulse width tp, for
sinusoidal currents, tp ≤ 20ms.
Fig.3. Maximum permissible non-repetitive peak
on-state current ITSM, versus number of cycles, for
sinusoidal currents, f = 50 Hz.
Fig.4. Maximum permissible rms current IT(RMS) ,
versus heatsink temperature Ths.
Fig.5. Maximum permissible repetitive rms on-state
current IT(RMS), versus surge duration, for sinusoidal
currents, f = 50 Hz; Ths ≤ 92˚C.
Fig.6. Normalised gate trigger voltage
VGT(Tj)/ VGT(25˚C), versus junction temperature Tj.
012345
0
1
2
3
4
5
6
7
8
= 180
120
90
60
30
IT(RMS) / A
Ptot / W Ths(max) / C
125
119.5
114
108.5
103
97.5
92
86.5
81
1
-50 0 50 100 150
0
1
2
3
4
5BT136X
92 C
Ths / C
IT(RMS) / A
10us 100us 1ms 10ms 100ms
10
100
1000
T / s
ITSM / A
TITSM
time
I
Tj initial = 25 C max
T
dI /dt limit
T
T2- G+ quadrant
0.01 0.1 1 10
0
2
4
6
8
10
12
surge duration / s
IT(RMS) / A
1 10 100 1000
0
5
10
15
20
25
30 BT136
Number of cycles at 50Hz
ITSM / A
TITSM
time
I
Tj initial = 25 C max
T
-50 0 50 100 150
0.4
0.6
0.8
1
1.2
1.4
1.6
Tj / C
VGT(Tj)
VGT(25 C)
June 2001 4 Rev 1.400
Philips Semiconductors Product specification
Triacs BT136X series
Fig.7. Normalised gate trigger current
IGT(Tj)/ IGT(25˚C), versus junction temperature Tj.
Fig.8. Normalised latching current IL(Tj)/ IL(25˚C),
versus junction temperature Tj.
Fig.9. Normalised holding current IH(Tj)/ IH(25˚C),
versus junction temperature Tj.
Fig.10. Typical and maximum on-state characteristic.
Fig.11. Transient thermal impedance Zth j-hs, versus
pulse width tp.
Fig.12. Typical commutation dV/dt versus junction
temperature, parameter commutation dIT/dt. The triac
should commutate when the dV/dt is below the value
on the appropriate curve for pre-commutation dIT/dt.
-50 0 50 100 150
0
0.5
1
1.5
2
2.5
3
Tj / C
T2+ G+
T2+ G-
T2- G-
T2- G+
IGT(Tj)
IGT(25 C)
0 0.5 1 1.5 2 2.5 3
0
2
4
6
8
10
12
VT / V
IT / A
Tj = 125 C
Tj = 25 C typ max
Vo = 1.27 V
Rs = 0.091 ohms
-50 0 50 100 150
0
0.5
1
1.5
2
2.5
3
Tj / C
IL(Tj)
IL(25 C)
10us 0.1ms 1ms 10ms 0.1s 1s 10s
0.01
0.1
1
10
tp / s
Zth j-hs (K/W)
tp
P
t
D
unidirectional
with heatsink compound
without heatsink compound
bidirectional
-50 0 50 100 150
0
0.5
1
1.5
2
2.5
3
Tj / C
IH(Tj)
IH(25C)
050 100 150
10
100
1000
1.83
Tj / C
dIcom/dt = 5.1 3.9 2.3
dVcom/dt (V/us)
A/ms 1.4
off-state dV/dt limit
BT136 SERIES
BT136...F SERIES
1
June 2001 5 Rev 1.400
Philips Semiconductors Product specification
Triacs BT136X series
MECHANICAL DATA
Dimensions in mm
Net Mass: 2 g
Fig.13. SOT186A; The seating plane is electrically isolated from all terminals.
Notes
1. Refer to mounting instructions for F-pack envelopes.
2. Epoxy meets UL94 V0 at 1/8".
10.3
max
3.2
3.0
4.6
max
2.9 max
2.8
seating
plane
6.4
15.8
max
0.6
2.5
2.54
5.08
123
3 max.
not tinned
3
0.5
2.5
0.9
0.7
M
0.4
15.8
max. 19
max.
13.5
min.
Recesses (2x)
2.5
0.8 max. depth
1.0 (2x)
1.3
June 2001 6 Rev 1.400
Philips Semiconductors Product specification
Triacs BT136X series
DEFINITIONS
DATA SHEET STATUS
DATA SHEET PRODUCT DEFINITIONS
STATUS2STATUS3
Objective data Development This data sheet contains data from the objective specification for
product development. Philips Semiconductors reserves the right to
change the specification in any manner without notice
Preliminary data Qualification This data sheet contains data from the preliminary specification.
Supplementary data will be published at a later date. Philips
Semiconductors reserves the right to change the specification without
notice, in ordere to improve the design and supply the best possible
product
Product data Production This data sheet contains data from the product specification. Philips
Semiconductors reserves the right to make changes at any time in
order to improve the design, manufacturing and supply. Changes will
be communicated according to the Customer Product/Process
Change Notification (CPCN) procedure SNW-SQ-650A
Limiting values
Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and
operation of the device at these or at any other conditions above those given in the Characteristics sections of
this specification is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
Philips Electronics N.V. 2001
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the
copyright owner.
The information presented in this document does not form part of any quotation or contract, it is believed to be
accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any
consequence of its use. Publication thereof does not convey nor imply any license under patent or other
industrial or intellectual property rights.
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices or systems where malfunction of these
products can be reasonably expected to result in personal injury. Philips customers using or selling these products
for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting
from such improper use or sale.
2 Please consult the most recently issued datasheet before initiating or completing a design.
3 The product status of the device(s) described in this datasheet may have changed since this datasheet was
published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com.
June 2001 7 Rev 1.400
