LTC2758 Dual Serial 18-Bit SoftSpan IOUT DACs Description Features n n n n n n n n n n n Maximum 18-Bit INL Error: 1 LSB Over Temperature Program or Pin-Strap Six Output Ranges: 0V to 5V, 0V to 10V, -2.5V to 7.5V, 2.5V, 5V, 10V Guaranteed Monotonic Over Temperature Glitch Impulse 0.4nV * s (3V), 2nV * s (5V) 18-Bit Settling Time: 2.1s 2.7V to 5.5V Single Supply Operation 1A Maximum Supply Current Voltage-Controlled Offset and Gain Trims Serial Interface with Readback of All Registers Clear and Power-On-Reset to 0V Regardless of Output Range 48-Pin 7mm x 7mm LQFP Package Applications n n n n The LTC(R)2758 is a dual 18-bit multiplying serial-input, current-output digital-to-analog converter. LTC2758A provides full 18-bit performance (INL and DNL of 1LSB maximum) over temperature without any adjustments. 18-bit monotonicity is guaranteed in all performance grades. This SoftSpanTM DAC operates from a single 3V to 5V supply and offers six output ranges (up to 10V) that can be programmed through the 3-wire SPI serial interface or pin-strapped for operation in a single range. Any on-chip register (including DAC output-range settings) can be read for verification in just one instruction cycle; and if you change register content, the altered register will be automatically read back during the next instruction cycle. Voltage-controlled offset and gain adjustments are also provided; and the power-on reset circuit and CLR pin both reset the DAC outputs to 0V regardless of output range. Instrumentation Medical Devices Automatic Test Equipment Process Control and Industrial Automation L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and SoftSpan is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. Typical Application Dual 18-Bit VOUT DAC with Software-Selectable Ranges REFERENCE 5V - + GEADJA ROFSA REFA RCOMA 0.4 RINA RFBA VDD IOUT1A 0.1F DAC A 4 IOUT2A VOSADJA LTC2758 RFBB IOUT1B DAC B GND LT1012 RCOMB + - GAIN B ADJUST IOUT2B VOSADJB GEADJB ROFSB REFB 0V TO 10V RANGE 0.8 0.6 5V SPI WITH READBACK 1.0 INL (LSB) GAIN A ADJUST LT1012 LTC2758 Integral Nonlinearity 27pF - + VOUTA LT1468 OFFSET A ADJUST 27pF - + 0.2 0 -0.2 -0.4 -0.6 -0.8 -1.0 VOUTB LT1468 0 65536 131072 CODE 196608 262143 2758 TA01b OFFSET B ADJUST RINB 2758 TA01a REFERENCE 5V For more information www.linear.com/LTC2758 2758fb 1 LTC2758 Absolute Maximum Ratings Pin Configuration (Notes 1, 2) 48 47 46 45 44 43 42 41 40 39 38 37 ROFSA ROFSA RFBA RFBA IOUT1A VOSADJA VOSADJB IOUT1B RFBB RFBB ROFSB ROFSB TOP VIEW REF A 1 REF A 2 RCOMA 3 GEADJA 4 RINA 5 RINA 6 GND 7 IOUT2AS 8 IOUT2AF 9 GND 10 CS/LD 11 SDI 12 36 35 34 33 32 31 30 29 28 27 26 25 REF B REF B RCOMB GEADJB RINB RINB GND IOUT2BS IOUT2BF GND LDAC S2 SCK 13 SRO 14 GND 15 VDD 16 GND 17 GND 18 CLR 19 RFLAG 20 DNC 21 M-SPAN 22 S0 23 S1 24 IOUT1X , IOUT2X to GND.............................................0.3V RINX, RCOMX , REFX, RFBX , ROFSX , VOSADJX , GEADJX to GND........................................................ 18V VDD to GND................................................... -0.3V to 7V Digital Inputs to GND.................................... -0.3V to 7V Digital Outputs to GND ......-0.3V to VDD +0.3V (max 7V) Operating Temperature Range LTC2758C................................................. 0C to 70C LTC2758I..............................................-40C to 85C Maximum Junction Temperature........................... 150C Storage Temperature Range................... -65C to 150C Lead Temperature (Soldering, 10 sec).................... 300C LX PACKAGE 48-LEAD (7mm x 7mm) PLASTIC LQFP TJMAX = 150C, JA = 53C/W order information http://www.linear.com/product/LTC2758#orderinfo LEAD FREE FINISH PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC2758BCLX#PBF LTC2758LX 48-Lead (7mm x 7mm) Plastic LQFP 0C to 70C LTC2758BILX#PBF LTC2758LX 48-Lead (7mm x 7mm) Plastic LQFP -40C to 85C LTC2758ACLX#PBF LTC2758LX 48-Lead (7mm x 7mm) Plastic LQFP 0C to 70C LTC2758AILX#PBF LTC2758LX 48-Lead (7mm x 7mm) Plastic LQFP -40C to 85C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ This product is only offered in trays. For more information go to: http://www.linear.com/packaging/. Some packages are available in 500 unit reels through designated sales channels with #TRMPBF suffix. 2 2758fb For more information www.linear.com/LTC2758 LTC2758 Electrical Characteristics VDD = 5V, V(RINX) = 5V unless otherwise specified. The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. SYMBOL PARAMETER CONDITIONS MIN LTC2758B TYP MAX MIN LTC2758A TYP MAX UNITS Static Performance Resolution l 18 18 18 Bits 18 Bits Monotonicity l DNL Differential Nonlinearity l 1 0.2 1 LSB INL Integral Nonlinearity l 2 0.5 1 LSB GE Gain Error All Output Ranges 6 32 Gain Error Temperature Coefficient Gain/Temp Bipolar Zero Error All Bipolar Ranges l Unipolar Zero-Scale Error Unipolar Ranges (Note 3) l PSR Power Supply Rejection VDD = 5V, 10% VDD = 3V, 10% l l ILKG IOUT1 Leakage Current TA = 25C TMIN to TMAX l BZE 48 l 0.25 Bipolar Zero Temperature Coefficient 0.25 36 1 3.2 0.03 3.2 LSB 1.6 4 0.1 0.3 0.8 2 LSB/V LSB/V 2 5 0.05 2 5 0.2 0.03 LSB ppm/C 24 0.2 0.05 LSB ppm/C nA nA VDD = 5V, V(RINX) = 5V unless otherwise specified. The l denotes specifications that apply over the full operating temperature range, otherwise specifications are at TA = 25C. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS Analog Pins Reference Inverting Resistors (Note 4) l 16 20 k RREF DAC Input Resistance (Notes 5, 6) l 8 10 k RFB Feedback Resistors (Note 6) l 8 10 k (Note 6) l 16 20 k l 1024 1280 k l 2048 ROFS Bipolar Offset Resistors RVOSADJ Offset Adjust Resistors RGEADJ Gain Adjust Resistors CIOUT1 Output Capacitance 2560 k Full-Scale Zero-Scale 90 40 pF Output Settling Time Span Code = 0000, 10V Step. To 0.0004% FS (Note 7) 2.1 s Glitch Impulse VDD = 5V (Note 8) VDD = 3V (Note 8) 2 0.4 nV*s nV*s Digital-to-Analog Glitch Impulse VDD = 5V (Note 9) VDD = 3V (Note 9) 2.6 0.6 nV*s nV*s Reference Multiplying BW 0V to 5V Range, Code = Full Scale, -3dB Bandwidth 1 MHz Multiplying Feedthrough Error 0V to 5V Range, VREF = 10V, 10kHz Sine Wave 0.4 mV Dynamic Performance THD Analog Crosstalk (Note 10) -109 dB Total Harmonic Distortion (Note 11) Multiplying -110 dB Output Noise Voltage Density (Note 12) at IOUT1 13 nV/Hz 2758fb For more information www.linear.com/LTC2758 3 LTC2758 Electrical Characteristics VDD = 5V, V(RINX) = 5V unless otherwise specified. The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS Power Supply VDD Supply Voltage IDD VDD Supply Current Digital Inputs = 0V or VDD l VIH Digital Input High Voltage 3.3V VDD 5.5V 2.7V VDD < 3.3V l l VIL Digital Input Low Voltage 4.5V < VDD 5.5V 2.7V VDD 4.5V l l IIN Digital Input Current VIN = GND to VDD CIN Digital Input Capacitance VOH VOL l 2.7 0.5 5.5 V 2 A Digital Inputs 2.4 2 V V 0.8 0.6 V V l 1 A VIN = 0V (Note 13) l 6 pF IOH = 200A 2.7V VDD 5.5V l IOL = 200A 2.7V VDD 5.5V l Hysteresis Voltage 0.1 V Digital Outputs timing Characteristics otherwise specifications are at TA = 25C. SYMBOL PARAMETER VDD - 0.4 V 0.4 V The l denotes specifications that apply over the full operating temperature range, CONDITIONS MIN TYP MAX UNITS VDD = 4.5V to 5.5V t1 SDI Valid to SCK Set-Up l 7 ns t2 SDI Valid to SCK Hold l 7 ns t3 SCK High Time l 11 ns t4 SCK Low Time l 11 ns t5 CS/LD Pulse Width l 9 ns t6 LSB SCK High to CS/LD High l 4 ns t7 CS/LD Low to SCK Positive Edge l 4 ns t8 CS/LD High to SCK Positive Edge l 4 ns t9 SRO Propagation Delay t10 CLR Pulse Width Low l 36 ns t11 LDAC Pulse Width Low l 15 ns t12 CLR Low to RFLAG Low CLOAD = 10pF (Note 13) l 50 ns t13 CS/LD High to RFLAG High CLOAD = 10pF (Note 13) l 40 ns SCK Frequency 50% Duty Cycle (Note 14) l 40 MHz CLOAD = 10pF 18 l ns VDD = 2.7V to 3.3V t1 SDI Valid to SCK Set-Up 9 ns t2 SDI Valid to SCK Hold (Note 13) t3 SCK High Time CL = 10pF l 9 ns l 15 ns t4 SCK Low Time l 15 ns t5 CS/LD Pulse Width l 12 ns t6 LSB SCK High to CS/LD High l 5 ns 4 l 2758fb For more information www.linear.com/LTC2758 LTC2758 timing Characteristics otherwise specifications are at TA = 25C. The l denotes specifications that apply over the full operating temperature range, SYMBOL PARAMETER t7 CS/LD Low to SCK Positive Edge CONDITIONS l MIN 5 ns t8 CS/LD High to SCK Positive Edge l 5 ns t9 SRO Propagation Delay CLOAD = 10pF TYP MAX 26 l UNITS ns t10 CLR Pulse Width Low l t11 LDAC Pulse Width Low l t12 CLR Low to RFLAG Low CLOAD = 10pF (Note 13) l 70 ns t13 CS/LD High to RFLAG high CLOAD = 10pF (Note 13) l 60 ns SCK Frequency 50% Duty Cycle (Note 14) l 25 MHz Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: Continuous operation above the specified maximum operating junction temperature may impair device reliability. Note 3: Calculation from feedback resistance and IOUT1 leakage current specifications; not production tested. In most applications, unipolar zeroscale error is dominated by contributions from the output amplifier. Note 4: Input resistors measured from RINX to RCOMX ; feedback resistors measured from RCOMX to REFX. Note 5: DAC input resistance is independent of code. Note 6: Parallel combination of the resistances from the specified pin to IOUT1X and from the specified pin to IOUT2X. Note 7: Using LT1468 with CFEEDBACK = 27pF. A 0.0004% settling time of 1.8s can be achieved by optimizing the time constant on an individual basis. See Application Note 120, 1ppm Settling Time Measurement for a Monolithic 18-Bit DAC. 60 ns 20 ns Note 8: Measured at the major carry transition, 0V to 5V range. Output amplifier: LT1468; CFB = 50pF. Note 9: Full-scale transition; REF = 0V. Note 10: Analog Crosstalk is defined as the AC voltage ratio VOUTB/VREFA , expressed in dB. REFB is grounded, and DAC B is set to 0V-5V span and zero-, mid- or full- scale code. VREFA is a 3VRMS, 1kHz sine wave. Note 11: REF = 6VRMS at 1kHz. 0V to 5V range. DAC code = FS. Output amplifier = LT1468. Note 12: Calculation from Vn = 4kTRB, where k = 1.38E-23 J/K (Boltzmann constant), R = resistance (), T = temperature (K), and B = bandwidth (Hz). 0V to 5V Range; zero-, mid-, or full-scale. Note 13: Guaranteed by design; not production tested. Note 14: When using SRO, maximum SCK frequency fMAX is limited by SRO propagation delay t9 as follows: 1 fMAX = , where tS is the setup time of the receiving device. 2 (t 9 + tS ) 2758fb For more information www.linear.com/LTC2758 5 LTC2758 Typical Performance Characteristics VDD = 5V, V(RINX) = 5V, TA = 25C, unless otherwise noted. Integral Nonlinearity (INL) 1.0 0V TO 10V RANGE 0.8 0.8 0.6 0.6 0.4 0.4 0.4 0.2 0.2 0.2 0 -0.2 INL (LSB) 0.6 0 -0.2 0 -0.2 -0.4 -0.4 -0.4 -0.6 -0.6 -0.6 -0.8 -0.8 -0.8 -1.0 -1.0 -1.0 65536 131072 CODE 196608 262143 0 65536 131072 CODE 196608 2758 G02 INL vs Temperature 0.8 DNL vs Temperature 1.0 0V TO 10V RANGE 0.6 0.8 DNL (LSB) 0 -INL 0 -0.6 -0.6 -0.8 -0.8 -1.0 -40 -20 0 20 40 TEMPERATURE (C) 60 +DNL -0.2 -0.4 -DNL 16 0.15ppm/C TYP 0.8 0.6 8 INL (LSB) BZE (LSB) 4 0 -4 5V 10V 2.5V -2.5V TO 7.5V -12 -16 -40 -20 0 20 40 TEMPERATURE (C) 60 80 85 2758 G07 6 16 12 -20 0 20 40 TEMPERATURE (C) 60 0 -40 80 85 -20 0 20 40 TEMPERATURE (C) 60 DNL vs Reference Voltage 1.0 5V RANGE 0.8 0.4 0.4 0.2 0.2 0 -0.2 -INL -INL -0.2 -0.4 -0.6 -0.6 -0.8 -0.8 4 6 8 10 2758 G08 +DNL +DNL -DNL -DNL 0 -0.4 -1.0 -10 -8 -6 -4 -2 0 2 V(RIN) (V) 5V RANGE 0.6 +INL +INL 80 85 2758 G06 INL vs Reference Voltage 12 -8 20 2.5V 5V 10V 0V TO 5V 0V TO 10V -2.5V TO 7.5V 2758 G05 1.0 2758 G03 4 2758 G04 Bipolar Zero Error vs Temperature -10V TO 10V 8 -1.0 -40 80 85 0.25ppm/C TYP 24 0.2 -0.4 0V -5V 0V TO TO TO 5V 5V 10V OUTPUT RANGE 28 0.4 0.2 -0.2 0V TO 10V RANGE 0.6 +INL 0.4 -2.5V -2.5V TO TO 2.5V 7.5V Gain Error vs Temperature 32 GE (LSB) 1.0 262143 DNL (LSB) 0 2758 G01 INL (LSB) INL vs Output Range 1.0 0V TO 10V RANGE 0.8 DNL (LSB) INL (LSB) Differential Nonlinearity (DNL) 1.0 -1.0 -10 -8 -6 -4 -2 0 2 V(RIN) (V) 4 6 8 10 2758 G09 2758fb For more information www.linear.com/LTC2758 LTC2758 Typical Performance Characteristics VDD = 5V, V(RINX) = 5V, TA = 25C, unless otherwise noted. INL vs VDD 1.0 1.0 0V TO 10V RANGE 0.8 0.8 +INL -20 0.4 DNL (LSB) 0.2 0 -INL -0.2 0.2 +DNL 0 -0.2 -DNL -0.4 -0.4 -0.6 -0.6 -0.8 -0.8 -1.0 2.5 -1.0 2.5 3 3.5 4 4.5 VDD (V) 5 5.5 ATTENUATION (dB) 0.4 ALL BITS ON D17 D16 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 0V TO 10V RANGE 0.6 0.6 INL (LSB) Multiplying Frequency Response vs Digital Code DNL vs VDD -40 -60 -80 -100 ALL BITS OFF 3 3.5 4 4.5 VDD (V) 5 -140 100 5.5 Settling Full-Scale Step Mid-Scale Glitch (VDD = 3V) 1M GATED SETTLING WAVEFORM 100V/DIV (AVERAGED) 2nV*s TYP CS/LD 5V/DIV VOUT 5mV/DIV (AVERAGED) VOUT 5mV/DIV (AVERAGED) 2758 G13 2758 G14 500ns/DIV 0V TO 5V RANGE LT1468 OUTPUT AMPLIFIER CFEEDBACK = 50pF RISING MAJOR CARRY TRANSITION. FALLING TRANSITION IS SIMILAR OR BETTER. Logic Threshold vs Supply Voltage Supply Current vs Logic Input Voltage LOGIC THRESHOLD (V) 4 3 2 VDD = 5V 1 Supply Current vs Update Frequency 2 100 1.75 10 1.5 SUPPLY CURRENT (mA) CLR, LDAC, SDI, SCK, CS/LD TIED TOGETHER RISING 1.25 2758 G15 500ns/DIV 0V TO 5V RANGE LT1468 OUTPUT AMPLIFIER CFEEDBACK = 50pF RISING MAJOR CARRY TRANSITION. FALLING TRANSITION IS SIMILAR OR BETTER. LT1468 AMP; CFEEDBACK = 20pF 0V TO 10V STEP VREF = -10V; SPAN CODE = 0000 tSETTLE = 1.8s to 0.0004% (18 BITS) 10M Mid-Scale Glitch (VDD = 5V) CS/LD 5V/DIV CS/LD 5V/DIV SUPPLY CURRENT (mA) 100k 10k FREQUENCY (Hz) 2758 G12 0.4nV*s TYP 5 1k 2758 G11 2758 G10 500ns/DIV 0V TO 5V OUTPUT RANGE LT1468 OUTPUT AMPLIFIER CFEEDBACK = 15pF -120 FALLING 1 0.75 ALTERNATING ZERO-SCALE AND FULL-SCALE 1 VDD = 5V 0.1 VDD = 3V 0.01 0.001 VDD = 3V 0 0 1 3 4 2 DIGITAL INPUT VOLTAGE (V) 5 2758 G16 0.5 2.5 3 3.5 4 4.5 VDD (V) 5 5.5 2758 G17 0.0001 1 100 10k 1M SCK FREQUENCY (Hz) 100M 2758 G18 2758fb For more information www.linear.com/LTC2758 7 LTC2758 Pin Functions REFA (Pins 1, 2): Feedback Resistor for the DAC A Reference Inverting Amplifier, and Reference Input for DAC A. The 20k feedback resistor is connected internally from REFA to RCOMA. For normal operation tie this pin to the output of the DAC A reference inverting amplifier (see Typical Application). Typically -5V; accepts up to 15V. Pins 1 and 2 are internally shorted together. RCOMA (Pin 3): Virtual Ground Point for the DAC A Reference Amplifier Inverting Resistors. The 20k reference inverting resistors are connected internally from RINA to RCOMA and from RCOMA to REFA, respectively (see Block Diagram). For normal operation tie RCOMA to the negative input of the external reference inverting amplifier (see Typical Application). GEADJA (Pin 4): Gain Adjust Pin for DAC A. This control pin can be used to null gain error or to compensate for reference errors. The gain change expressed in LSB is the same for any output range. See System Offset and Gain Adjustments in the Operation section. Tie to ground if not used. RINA (Pins 5, 6): Input Resistor for the DAC A External Reference Inverting Amplifier. The 20k input resistor is connected internally from RINA to RCOMA. For normal operation tie RINA to the external positive reference voltage (see Typical Application). Either or both of these precisionmatched resistor sets (each set comprising RINX, RCOMX and REFX) may be used to invert positive references to provide the negative voltages needed by the DACs. Typically 5V; accepts up to 15V. Pins 5 and 6 are internally shorted together. GND (Pins 7, 10, 15, 17, 18, 27, 30): Ground; tie to ground. IOUT2AS, IOUT2AF (Pins 8, 9): DAC A Current Output Complement Sense and Force Pins. Tie to ground via a clean, low-impedance path. These pins may be used with a precision ground buffer amp as a Kelvin sensing pair (see the Applications Information section). CS/LD (Pin 11): Synchronous Chip Select and Load Input Pin. SDI (Pin 12): Serial Data Input. Data is clocked in on the rising edge of the serial clock (SCK) when CS/LD is low. SCK (Pin 13): Serial Clock Input. 8 SRO (Pin 14): Serial Readback Output. Data is clocked out on the falling edge of SCK. Readback data begins clocking out after the last address bit A0 is clocked in. SRO is an active output only when the chip is selected (i.e., when CS/LD is low). Otherwise SRO presents a high-impedance output in order to allow other parts to control the bus. VDD (Pin 16): Positive Supply Input; 2.7V VDD 5.5V. Bypass with a 0.1F low-ESR ceramic capacitor to ground. CLR (Pin 19): Asynchronous Clear Input. When this pin is low, all DAC registers (both code and span) are cleared to zero. All DAC outputs are cleared to zero volts. RFLAG (Pin 20): Reset Flag Output. An active low output is asserted when there is a power-on reset or a clear event. Returns high when an Update command is executed. DNC (Pin 21): Do Not Connect. M-SPAN (Pin 22): Manual Span Control Pin. M-SPAN is used in conjunction with pins S2, S1 and S0 (Pins 25, 24 and 23) to configure all DACs for operation in a single, fixed output range. To configure the part for manual-span use, tie M-SPAN directly to VDD. The DAC output range is then set via hardware pin strapping of pins S2, S1 and S0 (rather than through the SPI port); and Write and Update commands have no effect on the active output span. To configure the part for SoftSpan use, tie M-SPAN directly to GND. The output ranges are then individually controllable through the SPI port; and pins S2, S1 and S0 have no effect. See Manual Span Configuration in the Operation section. MSPAN must be connected either directly to GND (SoftSpan configuration) or to VDD (manual-span configuration). S0 (Pin 23): Span Bit 0 Input. In Manual Span mode (MSPAN tied to VDD), Pins S0, S1 and S2 are pin-strapped to select a single fixed output range for all DACs. These pins should be tied to either GND or VDD even if they are unused. S1 (Pin 24): Span Bit 1 Input. In Manual Span mode (MSPAN tied to VDD), Pins S0, S1 and S2 are pin-strapped to select a single fixed output range for all DACs. These pins should be tied to either GND or VDD even if they are unused. 2758fb For more information www.linear.com/LTC2758 LTC2758 Pin Functions S2 (Pin 25): Span Bit 2 Input. In Manual Span mode (MSPAN tied to VDD), Pins S0, S1 and S2 are pin-strapped to select a single fixed output range for all DACs. These pins should be tied to either GND or VDD even if they are unused. LDAC (Pin 26): Asynchronous DAC Load Input. When LDAC is a logic low, all DACs are updated (CS/LD must be high). IOUT2BF, IOUT2BS (Pins 28, 29): DAC B Current Output Complement Force and Sense Pins. Tie to ground via a clean, low-impedance path. These pins may be used with a precision ground buffer amp as a Kelvin sensing pair (see the Applications Information section). RINB (Pins 31, 32): Input Resistor for the DAC B External Reference Inverting Amplifier. The 20k input resistor is connected internally from RINB to RCOMB. For normal operation tie RINB to the external positive reference voltage (see Typical Application). Either or both of these precisionmatched resistor sets (each set comprising RINX, RCOMX and REFX) may be used to invert positive references to provide the negative voltages needed by the DACs. Typically 5V; accepts up to 15V. Pins 31 and 32 are internally shorted together. GEADJB (Pin 33): Gain Adjust Pin for DAC B. This control pin can be used to null gain error or to compensate for reference errors. The gain change expressed in LSB is the same for any output range. See System Offset and Gain Adjustments in the Operation section. Tie to ground if not used. RCOMB (Pin 34): Virtual Ground Point for the DAC B Reference Amplifier Inverting Resistors. The 20k reference inverting resistors are connected internally from RINB to RCOMB and from RCOMB to REFB, respectively (see Block Diagram). For normal operation tie RCOMB to the negative input of the external reference inverting amplifier (see Typical Application). REFB (Pins 35, 36): Feedback Resistor for the DAC B Reference Inverting Amplifier, and Reference Input for DAC B. The 20k feedback resistor is connected internally from REFB to RCOMB. For normal operation tie this pin to the output of the DAC B reference inverting amplifier (see Typical Application). Typically -5V; accepts up to 15V. Pins 35 and 36 are internally shorted together. ROFSB (Pins 37, 38): Bipolar Offset Resistor for DAC B. These pins provide the translation of the output voltage range for bipolar spans. Accepts up to 15V; for normal operation tie to the positive reference voltage at RINB (Pins 31, 32). Pins 37 and 38 are internally shorted together. RFBB (Pins 39, 40): DAC B Feedback Resistor. For normal operation tie to the output of the I/V converter amplifier for DAC B (see Typical Application). The DAC output current from IOUT1B flows through the feedback resistor to the RFBB pins. Pins 39 and 40 are internally shorted together. IOUT1B (Pin 41): DAC B Current Output. This pin is a virtual ground when the DAC is operating and should reside at 0V. For normal operation tie to the negative input of the I/V converter amplifier for DAC B (see Typical Application). VOSADJB (Pin 42): DAC B Offset Adjust Pin. This voltagecontrol pin can be used to null unipolar offset or bipolar zero error. The offset change expressed in LSB is the same for any output range. See System Offset and Gain Adjustments in the Operation section. Tie to ground if not used. VOSADJA (Pin 43): DAC A Offset Adjust Pin. This voltagecontrol pin can be used to null unipolar offset or bipolar zero error. The offset change expressed in LSB is the same for any output range. See System Offset and Gain Adjustments in the Operation section. Tie to ground if not used. IOUT1A (Pin 44): DAC A Current Output. This pin is a virtual ground when the DAC is operating and should reside at 0V. For normal operation tie to the negative input of the I/V converter amplifier for DAC A (see Typical Application). RFBA (Pins 45, 46): DAC A Feedback Resistor. For normal operation tie to the output of the I/V converter amplifier for DAC A (see Typical Application). The DAC output current from IOUT1A flows through the feedback resistor to the RFBA pins. Pins 45 and 46 are internally shorted together. ROFSA (Pins 47, 48): Bipolar Offset Resistor for DAC A. This pin provides the translation of the output voltage range for bipolar spans. Accepts up to 15V; for normal operation tie to the positive reference voltage at RINA (Pins 5, 6). Pins 47 and 48 are internally shorted together. 2758fb For more information www.linear.com/LTC2758 9 LTC2758 Block Diagram 16 VDD 31,32 RINB 5,6 RINA 4 3 2.56M GEADJA RCOMA 2.56M 20k 20k RCOMB LTC2758 1,2 REFA GEADJB 37,38 ROFSB 47,48 ROFSA 45,46 RFBA 44 8 9 43 34 35,36 REFB 20k 20k 33 CODE REGISTERS 18 DAC A 18-BIT WITH SPAN SELECT IOUT1A IOUT2AS DAC REG CODE REGISTERS INPUT REG INPUT REG SPAN REGISTERS 3 DAC REG IOUT2AF DAC REG SPAN REGISTERS INPUT REG INPUT REG DAC REG 39,40 RFBB 18 DAC B 18-BIT WITH SPAN SELECT 3 IOUT1B IOUT2BS IOUT2BF VOSADJA VOSADJB POWER-ON RESET 7, 10, 15, 17, 18, 27, 30 GND 41 29 28 42 CONTROL AND READBACK LOGIC 22 M-SPAN 23 S0 24 S1 25 S2 20 RFLAG 19 CLR 11 CS/LD 12 SDI 13 SCK 26 LDAC 14 SRO 2758 BD timing diagram t1 t2 t3 1 SCK t6 t4 2 31 32 t8 SDI LSB t5 t7 CS/LD t11 LDAC t9 SRO 10 Hi-Z LSB 2758 TD 2758fb For more information www.linear.com/LTC2758 LTC2758 Operation Output Ranges VDD The LTC2758 is a dual, current-output, serial-input precision multiplying DAC with selectable output ranges. Ranges can either be programmed in software for maximum flexibility (each of the DACs can be programmed to any one of six output ranges) or hardwired through pin-strapping. Two unipolar ranges are available (0V to 5V and 0V to 10V), and four bipolar ranges (2.5V, 5V, 10V and -2.5V to 7.5V). These ranges are obtained when an external precision 5V reference is used. The output ranges for other reference voltages are easy to calculate by observing that each range is a multiple of the external reference voltage. The ranges can then be expressed: 0 to 1x, 0 to 2x, 0.5x, 1x, 2x, and -0.5x to 1.5x. Manual Span Configuration Multiple output ranges are not needed in some applications. To configure the LTC2758 to operate in a single span without additional operational overhead, tie the M-SPAN pin directly to VDD. The active output range for all DACs is then set via hardware pin strapping of pins S2, S1 and S0 (rather than through the SPI port); and Write and Update commands have no effect on the active output span. See Figure 1 and Table 3. Tie the M-SPAN pin to ground for normal SoftSpan operation. Input and DAC Registers The LTC2758 has 5 internal registers for each DAC, a total of 10 registers (see Block Diagram). Each DAC channel has two sets of double-buffered registers, one set for the code data, and one for the output range of the DAC, plus one readback register. Double buffering provides the LTC2758 VDD M-SPAN DAC A - + 10V DAC B - + 10V S2 S1 S0 CS/LD SDI SCK 2754 F01 Figure 1. Using M-SPAN to Configure the LTC2758 for Single-Span Operation (10V Range Shown) capability to simultaneously update the span (output range) and code, which allows smooth voltage transitions when changing output ranges. It also permits the simultaneous updating of multiple DACs. Each set of double-buffered registers comprises an Input register and a DAC register. Input register: The Write operation shifts data from the SDI pin into a chosen Input register. The Input registers are holding buffers; Write operations do not affect the DAC outputs. DAC register: The Update operation copies the contents of an Input register to its associated DAC register. The contents of a DAC register directly updates the associated DAC output voltage or output range. Note that updates always include both Code and Span register sets; but the values held in the DAC registers will only change if the associated Input register values have previously been altered via a Write operation. 2758fb For more information www.linear.com/LTC2758 11 LTC2758 Operation Serial Interface When the CS/LD pin is taken low, the data on the SDI pin is loaded into the shift register on the rising edge of the clock (SCK pin). The loading sequence required for the LTC2758 is one byte consisting of a 4-bit command word (C3 C2 C1 C0) and a 4-bit address word (A3 A2 A1 A0), then three bytes (24 bits) of data. When writing a code, the code data is left (MSB) justified; so that the 24-bit data field consists of 18 code bits followed by 6 don't-care bits. When writing an output range, the span data should occupy the last 4 bits of the second data byte, ordered S3 through S0. Figure 2 shows the SDI input word syntax for writing. When CS/LD is low, the SRO pin (Serial Readback Output) is an active output. The readback data begins after the command (C3-C0) and address (A3-A0) words have been shifted in to SDI. SRO outputs a logic low from the falling edge of CS/LD until the Readback data begins. When CS/LD is high, the SRO pin presents a high impedance (three-state) output. LDAC is an asynchronous update pin. When LDAC is taken low, all DACs are updated with code and span data (data in the Input buffers is copied into the DAC buffers). CS/LD must be high during this operation; otherwise LDAC is locked out and will have no effect. The use of LDAC is functionally identical to the "Update All DACs" serial input command. The codes for the command (C3-C0) are defined in Table 1; Table 2 defines the codes for the address (A3-A0). Readback In addition to the Code and Span register sets, each DAC has one Readback register associated with it. Every instruction cycle, the contents of one of the on-chip registers is copied into a Readback register and serially shifted out through the SRO pin. Readback data always appears in the 24-bit data field, starting on the falling SCK edge immediately after the last address bit is shifted in on SDI. When reading a code, code 12 data occupies the first 18 bits of the 24-bit field; and the span bits are the last four bits of the second data byte when checking the output range. In both cases, all other bits in the 24-bit data field are filled by zeros. Figure 2 shows the input and readback sequences. The data outputted by SRO is always in the same position and sequence as the input data. Note, however, that this means that the SRO data shifts out one-half clock cycle earlier than the corresponding bit shifting in on SDI. For example, code bit D9, which is shifted in to SDI on the rising edge of SCK clock 17, is clocked out of SRO on the falling edge of clock 16. This allows D9 to be clocked to an external microprocessor on the rising edge of clock 17. For Read commands, the requested data is shifted out of SRO in the 3-byte (24-bit) data field immediately after the command/address byte. There is no instruction-cycle latency for Read commands; the data shifts out in the same instruction cycle in which it was requested. For non-read (i.e., Write and/or Update) commands, SRO automatically shifts out the contents of the buffer that was acted upon in the preceding command. This "rolling readback" default mode of operation can dramatically reduce the number of instruction cycles needed, since most commands can be verified during subsequent commands with no additional overhead. A conceptual flow diagram is shown in Figure 3. Table 1 shows, for each antecedent command, which register (`readback pointer') will be copied into the Readback register and outputted from SRO during the following instruction cycle. Span Readback in Manual Span Configuration If a Span DAC register is chosen for readback, SRO responds by outputting the actual output span; this is true whether the LTC2758 is configured for SoftSpan (M-SPAN tied to GND) or manual span (M-SPAN tied to VDD). In SoftSpan configuration, SRO outputs the span code from the Span DAC register (programmed through the SPI port). In manual span configuration, the active output range is controlled by pins S2, S1 and S0, so SRO outputs the logic values of these pins. The span code bits S2, S1 and S0 always appear in the same order and positions in the SRO output sequence; see Figure 2. 2758fb For more information www.linear.com/LTC2758 LTC2758 Operation Table 1. Command Codes C3 CODE C2 C1 C0 COMMAND READBACK POINTER- CURRENT INPUT WORD W0 READBACK POINTER- NEXT INPUT WORD W+1 0 0 1 0 Write Span DAC n Set by Previous Command Input Span Register DAC n 0 0 1 1 Write Code DAC n Set by Previous Command Input Code Register DAC n 0 1 0 0 Update DAC n Set by Previous Command DAC Span Register DAC n 0 1 0 1 Update All DACs Set by Previous Command DAC Code Register DAC n 0 1 1 0 Write Span DAC n Update DAC n Set by Previous Command DAC Span Register DAC n 0 1 1 1 Write Code DAC n Update DAC n Set by Previous Command DAC Code Register DAC n 1 0 0 0 Write Span DAC n Update All DACs Set by Previous Command DAC Span Register DAC n 1 0 0 1 Write Code DAC n Update All DACs Set by Previous Command DAC Code Register DAC n 1 0 1 0 Read Input Span Register DAC n Input Span Register DAC n 1 0 1 1 Read Input Code Register DAC n Input Code Register DAC n 1 1 0 0 Read DAC Span Register DAC n DAC Span Register DAC n 1 1 0 1 Read DAC Code Register DAC n DAC Code Register DAC n 1 1 1 1 No Operation Set by Previous Command DAC Code Register DAC n - System Clear - DAC Span Register DAC A - Initial Power-Up or Power Interrupt - DAC Span Register DAC A Codes not shown are reserved-do not use Table 2. Address Codes Table 3. Span Codes A3 A2 A1 A0 n S3 S2 S1 S0 0 0 0 x DAC A x 0 0 0 Unipolar 0V to 5V 0 0 1 x DAC B x 0 0 1 Unipolar 0V to 10V 1 1 1 x All DACs (Note 1) x 0 1 0 Bipolar -5V to 5V x 0 1 1 Bipolar -10V to 10V x 1 0 0 Bipolar -2.5V to 2.5V x 1 0 1 Bipolar -2.5V to 7.5V Codes not shown are reserved-do not use. x = Don't Care. Note 1. If readback is taken using the All DACs address, the LTC2758 defaults to DAC A. SPAN Codes not shown are reserved-do not use. x = Don't Care. 2758fb For more information www.linear.com/LTC2758 13 LTC2758 operation Examples 1. Load DAC A with 0V to 10V range, output at zero volts; and DAC B with 10V range, output at zero volts. Note the DAC outputs should change at the same time. a) CS/LD. Clock SDI: 00101111 00000000 00000011 00000000 b) CS/LD Span Input register- Range of DACs set to bipolar 10V. c) CS/LD. Clock SDI: 00100000 00000000 00000001 00000000 d) CS/LD Span Input register- Range of DAC A set to unipolar 0V to 10V. e) CS/LD. Clock SDI: 00111111 10000000 00000000 00XXXXXX f) CS/LD Code Input register- Code of all DACs set to mid-scale. 2. Load DAC B with 2.5V range with its output at zero volts. Use readback to check Input register contents before updating the DAC output (i.e., before copying Input register contents into DAC registers). Note that after power-on, the code in Input registers is zero. a) CS/LD. Clock SDI: 00110010 10000000 00000000 00XXXXXX b) CS/LD Code Input register- DAC B set to mid-scale. c) CS/LD. Clock SDI: 00100010 00000000 00000100 00000000 Data out on SRO: 10000000 00000000 00000000 Verifies Code Input register- DAC B set to mid-scale. d) CS/LD Span Input register- Range of DAC B set to Bipolar 2.5V range. h) CS/LD Code Input register- Code of DAC A set to zero. e) CS/LD. Clock SDI: 10100010 XXXXXXXX XXXXXXXX XXXXXXXX Data Out on SRO: 00000000 00000100 00000000 Verifies Span Input register- DAC B set to Bipolar 2.5V Range. CS/LD i) CS/LD. Clock SDI: 01001111 XXXXXXXX XXXXXXXX XXXXXXXX f) CS/LD. Clock SDI: 01000010 XXXXXXXX XXXXXXXX XXXXXXXX j) CS/LD Update all DACs for both Code and Range. g) CS/LD Update DAC B for both Code and Range k) Alternatively steps i and j could be replaced with LDAC . h) Alternatively steps f and g could be replaced with LDAC . g) CS/LD. Clock SDI: 00110000 00000000 00000000 00XXXXXX 14 2758fb For more information www.linear.com/LTC2758 LTC2758 operation System Offset and Reference Adjustments Many systems require compensation for overall system offset. This may be an order of magnitude or more greater than the offset of the LTC2758, which is so low as to be dominated by external output amplifier errors even when using the most precise op amps. The offset adjust pins VOSADJX can be used to null unipolar offset or bipolar zero error. The offset change expressed in LSB is the same for any output range: 5V V REF A 5V control voltage applied to VOSADJX produces VOS = -2048 LSB in any output range, assuming a 5V reference voltage at RINX. In voltage terms, the offset delta is attenuated by a factor of 32, 64 or 128, depending on the output range. (These functions hold regardless of reference voltage.) VOS = -(1/128)VOSADJX VOS = -(1/64)VOSADJX VOS = -(1/32)VOSADJX [0V to 5V, 2.5V spans] [0V to 10V, 5V, -2.5V to 7.5V spans] [10V span] The gain error adjust pins GEADJX can be used to null gain error or to compensate for reference errors. The gain error change expressed in LSB is the same for any output range: GE = V(GE ADJX ) * 2048 V(RINX ) The gain-error delta is non-inverting for positive reference voltages. Note that this pin compensates the gain by altering the inverted reference voltage V(REFX). In voltage terms, the V(REFX) delta is inverted and attenuated by a factor of 128. V(REFX) = -(1/128)GEADJX The nominal input range of these pins is 5V; other voltages of up to 15V may be used if needed. However, do not use voltages divided down from power supplies; reference-quality, low-noise inputs are required to maintain the best DAC performance. The VOSADJX pins have an input impedance of 1.28M. These pins should be driven with a Thevenin-equivalent impedance of 10k or less to preserve the settling performance of the LTC2758. They should be shorted to GND if not used. The GEADJX pins have an input impedance of 2.56M, and are intended for use with fixed reference voltages only. They should be shorted to GND if not used. Power-On Reset and Clear When power is first applied to the LTC2758, all DACs power-up in unipolar 5V mode (S3 S2 S1 S0 = 0000). All internal DAC registers are reset to 0 and the DAC outputs initialize to zero volts. If the part is configured for manual span operation, all DACs will be set into the pin-strapped range at the first Update command. This allows the user to simultaneously update span and code for a smooth voltage transition into the chosen output range. When the CLR pin is taken low, a system clear results. The DAC buffers are reset to 0 and the DAC outputs are all reset to zero volts. The Input buffers are left intact, so that any subsequent Update command (including the use of LDAC) restores the addressed DACs to their respective previous states. If CLR is asserted during an instruction, i.e., when CS/LD is low, the instruction is aborted. Integrity of the relevant Input buffers is not guaranteed under these conditions, therefore the contents should be checked using readback or replaced. The RFLAG pin is used as a flag to notify the system of a loss of data integrity. The RFLAG output is asserted low at power-up, system clear, or if the supply VDD dips below approximately 2V; and stays asserted until any valid Update command is executed. 2758fb For more information www.linear.com/LTC2758 15 16 SRO SDI SRO C3 SDI 0 0 0 C1 3 C1 0 0 0 COMMAND C2 READBACK SPAN Hi-Z WRITE SPAN C3 2 COMMAND C2 READBACK CODE Hi-Z WRITE CODE 1 SCK CS/LD 0 C0 0 C0 4 0 A3 0 A3 5 A1 A1 0 0 0 ADDRESS A2 0 ADDRESS A2 6 7 0 A0 0 A0 8 0 X D17 D17 9 0 X D16 D16 10 0 X 0 X D14 D14 12 0 X D13 D13 X D12 D12 14 X D11 D11 15 0 0 12 DON'T-CARE 13 0 X D10 D10 D9 17 D8 18 0 X D9 0 X D8 19 D7 0 X D7 18-BIT DAC CODE 16 0 X D6 D6 20 S3 S3 D5 D5 21 Figure 2. Serial Input and Output Sequences D15 D15 11 S2 23 S1 D3 D3 S1 SPAN S2 D4 D4 22 S0 S0 D2 D2 24 0 X D1 D1 25 0 X D0 D0 26 0 X 0 X X 0 X X 29 0 X 30 X 0 0 0 X 0 6 DON'T-CARE 28 8 DON'T-CARE 27 0 X 0 X 31 0 X 0 X 32 2758 F02 LTC2758 operation 2758fb For more information www.linear.com/LTC2758 LTC2758 Operation SDI WRITE CODE DAC A WRITE CODE DAC B WRITE SPAN DAC A WRITE SPAN DAC B UPDATE ALL DACs ... SRO ... READ CODE INPUT REGISTER DAC A READ CODE INPUT REGISTER DAC B READ SPAN INPUT REGISTER DAC A READ SPAN INPUT REGISTER DAC B READ CODE DAC REGISTER DAC A 2758 F03 Figure 3. Rolling Readback 2758fb For more information www.linear.com/LTC2758 17 LTC2758 Applications Information Op Amp Selection Table 4. Coefficients for the Equations of Table 5 Because of the extremely high accuracy of the 18-bit LTC2758, careful thought should be given to op amp selection in order to achieve the exceptional performance of which the part is capable. Fortunately, the sensitivity of INL and DNL to op amp offset has been greatly reduced compared to previous generations of multiplying DACs. Tables 4 and 5 contain equations for evaluating the effects of op amp parameters on the LTC2758's accuracy when programmed in a unipolar or bipolar output range. These are the changes the op amp can cause to the INL, DNL, unipolar offset, unipolar gain error, bipolar zero and bipolar gain error. OUTPUT RANGE A1 A2 A3 5V 1.1 2 1 10V 2.2 3 0.5 5V 2 2 1 A4 A5 1 1.5 1 1.5 10V 4 4 0.83 1 2.5 2.5V 1 1 1.4 1 1 -2.5V to 7.5V 1.9 3 0.7 0.5 1.5 Table 6 contains a partial list of LTC precision op amps recommended for use with the LTC2758. The easy-to-use design equations simplify the selection of op amps to meet the system's specified error budget. Select the amplifier from Table 6 and insert the specified op amp parameters in Table 5. Add up all the errors for each category to determine the effect the op amp has on the accuracy of the part. Arithmetic summation gives an (unlikely) worst-case effect. A root-sum-square (RMS) summation produces a more realistic estimate. Table 5. Easy-to-Use Equations Determine Op Amp Effects on DAC Accuracy in All Output Ranges (Circuit of Page 1). Subscript 1 Refers to Output Amp, Subscript 2 Refers to Reference Inverting Amp. UNIPOLAR BIPOLAR GAIN BIPOLAR ZERO UNIPOLAR GAIN DNL (LSB) INL (LSB) OFFSET (LSB) ERROR (LSB) ERROR (LSB) ERROR (LSB) 5V 5V 5V 5V 5V 5V VOS1 (mV) VOS1 * 12.1* V VOS1 *3.1* V A3*VOS1 *52.4 * V A3*VOS1 *78.6 * V VOS1 *52.4 * V VOS1 * 52.4* V REF REF REF REF REF REF 5V 5V 5V 5V 5V 5V IB1 (nA) IB1 *0.0012* V IB1 *0.00032 * V IB1 *0.524* V IB1 *0.524* V IB1 *0.0072 * V IB1 *0.0072* V REF REF REF REF REF REF 66 6 524 524 AVOL1 (V/mV) A1* A A2 * A 0 0 A5* A5* AVOL1 AVOL1 VOL1 VOL1 5V 5V 5V 0 0 0 A4*VOS2 *52.4 * V V VOS2 (mV) *104.8* *104.8* VREF VREF OS2 VREF OS2 5V 5V 5V 0 0 0 IB2 (nA) A4*IB2 *0.524 * IB2 *1.048* IB2 *1.048* VREF VREF VREF 524 524 0 0 0 AVOL2 (V/mV) A4* 262 AVOL2 AVOL2 AVOL2 OP AMP ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) Table 6. Partial List of LTC Precision Amplifiers Recommended for Use with the LTC2758 with Relevant Specifications AMPLIFIER SPECIFICATIONS AMPLIFIER VOS V IB nA A VOL V/mV VOLTAGE NOISE nV/Hz CURRENT NOISE pA/Hz SLEW RATE V/s GAIN BANDWIDTH PRODUCT MHz tSETTLING with LTC2758 s POWER DISSIPATION mW LTC1150 10 0.05 5600 90 0.0018 3 2.5 10ms 24 LT1001 25 2 800 10 0.12 0.25 0.8 120 46 LT1012 25 0.1 2000 14 0.02 0.2 1 120 11.4 LT1097 50 0.35 2500 14 0.008 0.2 0.7 120 11 LT1468 75 10 5000 5 0.6 22 90 2.1 117 18 2758fb For more information www.linear.com/LTC2758 LTC2758 Applications Information Op amp offset contributes mostly to DAC output offset and gain error, and has minimal effect on INL and DNL. For example, consider the LTC2758 in unipolar 5V output range. (Note that for this example, the LSB size is 19V.) An op amp offset of 35V will cause 1.8LSB of output offset, and 1.8LSB of gain error; but 0.4LSB of INL, and just 0.1LSB of DNL. While not directly addressed by the simple equations in Tables 4 and 5, temperature effects can be handled just as easily for unipolar and bipolar applications. First, consult an op amp's data sheet to find the worst-case VOS and IB over temperature. Then, plug these numbers in the VOS and IB equations from Table 5 and calculate the temperature-induced effects. For applications where fast settling time is important, Application Note 120, 1ppm Settling Time Measurement for a Monolithic 18-Bit DAC, offers a thorough discussion of 18-bit DAC settling time and op amp selection. Recommendations For DC or low-frequency applications, the LTC1150 is the simplest 18-bit accurate output amplifier. An auto-zero amp, its exceptionally low offset (10V max) and offset drift (0.01V/C) make nulling unnecessary. For swings above 8V, use an LT1010 buffer to boost the load current capability. The settling of auto-zero amps is a special case; see Application Note 120, 1ppm Settling Time Measurement for a Monolithic 18-Bit DAC, Appendix E, for details. The LT1012 and LT1001 are good intermediate output-amp solutions that achieve moderate speed and good accuracy. They are also excellent choices for the reference inverting amplifier in fixed-reference applications. For high speed applications, the LTC1468 settles in 2.1s. Note that the 75V max offset will degrade the INL at the DAC output by up to 0.9LSB. For high-speed applications demanding higher precision, the amplifier offset can be nulled with a digital potentiometer. The Typical Application on the last page shows a composite output amplifier that achieves fast settling (8s) and very low offset (3V max) without offset nulling. This circuit offers high open-loop gain (1000V/mV min), low input bias current (0.15nA max), fast slew rate (25V/s min), and a high gain-bandwidth product (30MHz typ). The high speed path consists of an LTC6240HV, which is an 18MHz ultralow bias current amplifier, followed by an LT1360, a 50MHz fast-slewing amplifier which provides additional gain and the ability to swing to 10V at the output. Compensation is taken from the output of the LTC6240HV, allowing the use of a much larger compensation capacitor than if taken after the gain-of-five stage. An LTC2054HV auto-zero amplifier senses the voltage at IOUT1 and drives the non-inverting input of the LTC6240HV to eliminate the offset of the high speed path. The 100:1 attenuator and input filter reduce the low frequency noise in this stage while maintaining low DC offset. Precision Voltage Reference Considerations Much in the same way selecting an operational amplifier for use with the LTC2758 is critical to the performance of the system, selecting a precision voltage reference also requires due diligence. The output voltage of the LTC2758 is directly affected by the voltage reference; thus, any voltage reference error will appear as a DAC output voltage error. There are three primary error sources to consider when selecting a precision voltage reference for 18-bit applications: output voltage initial tolerance, output voltage temperature coefficient and output voltage noise. Initial reference output voltage tolerance, if uncorrected, generates a full-scale error term. Choosing a reference with low output voltage initial tolerance, like the LT1236 (0.05%), minimizes the gain error caused by the reference; however, a calibration sequence that corrects for system zero- and full-scale error is always recommended. A reference's output voltage temperature coefficient affects not only the full-scale error, but can also affect the circuit's INL and DNL performance. If a reference is chosen with a loose output voltage temperature coefficient, then the DAC output voltage along its transfer characteristic will be very dependent on ambient conditions. Minimizing the error due to reference temperature coefficient can be achieved by choosing a precision reference with a low output voltage temperature coefficient and/or tightly controlling the ambient temperature of the circuit to minimize temperature gradients. 2758fb For more information www.linear.com/LTC2758 19 LTC2758 Applications Information Table 7. Partial List of LTC Precision References Recommended for Use with the LTC2758 with Relevant Specifications INITIAL TOLERANCE TEMPERATURE DRIFT 0.1Hz to 10Hz NOISE LT1019A-5, LT1019A-10 0.05% max 5ppm/C max 12VP-P LT1236A-5, LT1236A-10 0.05% max 5ppm/C max 3VP-P LT1460A-5, LT1460A-10 0.075% max 10ppm/C max 20VP-P LT1790A-2.5 0.05% max 10ppm/C max 12VP-P LTC6652A-5 0.05% max 5ppm/C max 2.8ppmP-P LTC6655A-2.5 LTC6655A-5 0.025% max 2ppm/C max 0.25ppmP-P REFERENCE As precision DAC applications move to 18-bit performance, reference output voltage noise may contribute a dominant share of the system's noise floor. This in turn can degrade system dynamic range and signal-to-noise ratio. Care should be exercised in selecting a voltage reference with as low an output noise voltage as practical for the system resolution desired. Precision voltage references like the LT1236 or LTC6655 produce low output noise in the 0.1Hz to 10Hz region, well below the 18-bit LSB level in 5V or 10V full-scale systems. However, as the circuit bandwidths increase, filtering the output of the reference may be required to minimize output noise. 20 Grounding As with any high-resolution converter, clean grounding is important. A low-impedance analog ground plane is necessary, as are star grounding techniques. Keep the board layer used for star ground continuous to minimize ground resistances; that is, use the star-ground concept without using separate star traces. The IOUT2 pins are of particular concern; INL will be degraded by the codedependent currents carried by the IOUT2XF and IOUT2XS pins if voltage drops to ground are allowed to develop. The best strategy here is to tie the pins to the star ground plane by multiple vias located directly underneath the part. Alternatively, the pins may be routed to the star ground point if necessary; join the force and sense pins together at the part and route one trace for each channel of no more than 30 squares of 1oz copper. In the rare case in which neither of these alternatives is practicable, a force/sense amplifier should be used as a ground buffer (see Figure 4). Note, however, that the voltage offset of the ground buffer amp directly contributes to the effects on accuracy specified in Table 5 under `VOS1'. The combined effects of the offsets can be calculated by substituting the total offset from IOUT1X to IOUT2XS for VOS1 in the equations. 2758fb For more information www.linear.com/LTC2758 LTC2758 Applications Information ALTERNATE AMPLIFIER FOR OPTIMUM SETTLING TIME PERFORMANCE IOUT2AS 8 6 1 + 2 IOUT2AF 1000pF LT1468 ZETEX BAT54S 200 200 2 9 3 6 LT1012 + 9 - IOUT2AF 8 - IOUT2AS 1 2 3 ZETEX* BAT54S 3 2 3 *SCHOTTKY BARRIER DIODE VREF 5V 47, 48 ROFSA RFBA 45, 46 5, 6 RINA + 4 LT1012 - 6 3 15pF GEADJA DAC A 3 RCOMA 2 IOUT1A 44 2 - IOUT2A 8, 9 3 + LT1468 6 VOUTA VOSADJA 43 150pF 1, 2 REFA - + DAC B LTC2758 2758 F05 Figure 4. Optional Circuits for Driving IOUT2 from GND with a Force/Sense Amplifier 2758fb For more information www.linear.com/LTC2758 21 LTC2758 Package Description Please refer to http://www.linear.com/product/LTC2758#packaging for the most recent package drawings. LX Package 48-Lead Plastic LQFP (7mm x 7mm) (Reference LTC DWG # 05-08-1760 Rev A) 7.15 - 7.25 9.00 BSC 5.50 REF 7.00 BSC 48 0.50 BSC 1 2 48 SEE NOTE: 4 1 2 9.00 BSC 5.50 REF 7.00 BSC 7.15 - 7.25 0.20 - 0.30 A A PACKAGE OUTLINE C0.30 - 0.50 1.30 MIN RECOMMENDED SOLDER PAD LAYOUT APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 1.60 1.35 - 1.45 MAX 11 - 13 R0.08 - 0.20 GAUGE PLANE 0.25 0 - 7 11 - 13 0.09 - 0.20 1.00 REF 0.50 BSC 0.17 - 0.27 0.05 - 0.15 0.45 - 0.75 SECTION A - A COMPONENT PIN "A1" TRAY PIN 1 BEVEL 22 XXYY LTCXXXX LX-ES Q_ _ _ _ _ _ e3 NOTE: 1. PACKAGE DIMENSIONS CONFORM TO JEDEC #MS-026 PACKAGE OUTLINE 2. DIMENSIONS ARE IN MILLIMETERS 3. DIMENSIONS OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.25mm ON ANY SIDE, IF PRESENT 4. PIN-1 INDENTIFIER IS A MOLDED INDENTATION, 0.50mm DIAMETER 5. DRAWING IS NOT TO SCALE LX48 LQFP 0113 REV A PACKAGE IN TRAY LOADING ORIENTATION 2758fb For more information www.linear.com/LTC2758 LTC2758 Revision History REV DATE DESCRIPTION PAGE NUMBER A 09/13 Fixed RCOMA (Pin 3) description 8 Updated Typical Application 24 B 11/16 Updated amplifier part numbers 19 2758fb Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. For more information www.linear.com/LTC2758 23 LTC2758 Typical Application Composite Amplifier Circuit Achieves Both Fast Settling and 18-Bit Precision with No Adjustments 12V IN 15V OUT LTC6655-5 0.1F + - 10F LT1012 -15V 47, 48 5, 6 ROFSA 37, 38 RINA ROFSB 34 31, 32 RCOMB RINB 3 RCOMA 16 V DD 10k 26 LDAC 10k 19 43 4 42 33 22 25 24 23 100pF 1, 2, 35, 36 REFA, REFB 45, 46 RFBA 44 1k IOUT1A VOUTA 10k 10k CLR 1F IOUT2A 8, 9 5V 5V - + LTC2054HV 1k -5V 1F VOSADJA - + 100pF LTC6240HV -5V 5pF 10 15V + - LT1360 -15V 4.02k GEADJA 1k LTC2758 VOSADJB GEADJB RFBB M-SPAN IOUT1B 39, 40 41 VOUTB 1k 10k 10k S2 S1 1F S0 IOUT2B CS/LD 11 SDI SCK 12 SRO 13 14 GND 28, 29 5V 5V - + LTC2054HV 1k -5V 1F 7, 10, 15, 17, 18, 27, 30 - + 100pF LTC6240HV -5V 10 15V + - 5pF LT1360 -15V 4.02k 1k 2758 TA02 SPI BUS Related Parts PART NUMBER DESCRIPTION COMMENTS LTC2757 Single Parallel 18-Bit IOUT SoftSpan DAC 1LSB INL/DNL, Software-Selectable Ranges, 7mm x 7mm LQFP-48 Package LTC1592 Single Serial 16-/14-/12-Bit IOUT SoftSpan DACs 1LSB INL, DNL, Software-Selectable Ranges, 16-Lead SSOP Package LTC2752 Dual Serial 16-Bit IOUT SoftSpan DAC 1LSB INL/DNL, Software-Selectable Ranges, 7mm x 7mm LQFP-48 Package LTC2754-12 Quad Serial 16-/12-Bit IOUT SoftSpan DACs 1LSB INL/DNL, Software-Selectable Ranges, 7mm x 8mm QFN-52 Package LTC2704-12 Quad Serial 16-/14-/12-Bit VOUT SoftSpan DACs 1LSB INL/DNL, Software-Selectable Ranges, Integrated Amplifiers LTC6655 Low Drift Precision Buffered Reference 0.025% Max Tolerance, 2ppm/C Max, 0.25ppmP-P 0.1Hz to 10Hz Noise LT1236 Precision Reference 0.05% Max Tolerance, 5ppm/C Max, 3VP-P 0.1Hz to 10Hz Noise References LT1460 Micropower Precision Series Reference 0.075% Max Tolerance, 10ppm/C Max, 20VP-P 0.1Hz to 10Hz Noise LT1790 Micropower Low Dropout Reference 0.05% Max Tolerance, 10ppm/C Max, 12VP-P 0.1Hz to 10Hz Noise LTC6652 Precision Low Drift Low Noise Buffered Reference 0.05% Max Tolerance, 5ppm/C Max, 2.1ppmP-P 0.1Hz to 10Hz Noise LTC1150 Zero-Drift Op Amp with Internal Capacitors 10V Max Offset, 16V High Voltage Operation, 1.8VP-P Noise LT1012 Precision Op Amp 25V Max Offset, 100pA Max Input Current, 0.5VP-P Noise, 380A Supply Current LT1001 Precision Op Amp 25V Max Offset, 0.3VP-P Noise, High Output Drive LT1468 Single 16-Bit Accurate Op Amp 900ns Settling, 90MHz GBW, 22V/s Slew Rate, 75V Max Offset Amplifiers 24 2758fb Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 For more information www.linear.com/LTC2758 (408) 432-1900 FAX: (408) 434-0507 www.linear.com/LTC2758 LT 1116 REV B * PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 2011