19-1194; Rev 4; 4/11 KIT ATION EVALU E L B AVAILA +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs ____________________________Features The MAX1110/MAX1111 low-power, 8-bit, 8-channel analog-to-digital converters (ADCs) feature an internal track/hold, voltage reference, clock, and serial interface. They operate from a single 2.7V to 5.5V supply and consume only 85A while sampling at rates up to 50ksps. The MAX1110's 8 analog inputs and the MAX1111's 4 analog inputs are software-configurable, allowing unipolar/bipolar and single-ended/differential operation. Successive-approximation conversions are performed using either the internal clock or an external serial-interface clock. The full-scale analog input range is determined by the 2.048V internal reference, or by an externally applied reference ranging from 1V to VDD. The 4-wire serial interface is compatible with the SPITM, QSPITM, and MICROWIRETM serial-interface standards. A serial-strobe output provides the end-of-conversion signal for interrupt-driven processors. o 2.7V to 5.5V Single Supply The MAX1110/MAX1111 have a software-programmable, 2A automatic power-down mode to minimize power consumption. Using power-down, the supply current is reduced to 6A at 1ksps, and only 52A at 10ksps. Power-down can also be controlled using the SHDN input pin. Accessing the serial interface automatically powers up the device. The MAX1110 is available in a 20-pin SSOP package. The MAX1111 is available in a small 16-pin QSOP package. Ordering Information appears at end of data sheet. o Low Power: 85A at 50ksps 6A at 1ksps o 8-Channel Single-Ended or 4-Channel Differential Inputs (MAX1110) o 4-Channel Single-Ended or 2-Channel Differential Inputs (MAX1111) o Internal Track/Hold; 50kHz Sampling Rate o Internal 2.048V Reference o SPI/QSPI/MICROWIRE-Compatible Serial Interface o Software-Configurable Unipolar or Bipolar Inputs o Total Unadjusted Error: 1 LSB (max) 0.3 LSB (typ) ________________Functional Diagram CS SCLK DIN INPUT SHIFT REGISTER SHDN ________________________Applications Portable Data Logging Hand-Held Measurement Devices Medical Instruments System Diagnostics Solar-Powered Remote Systems 4mA to 20mA-Powered Remote Data-Acquisition Systems CH0 CH1 CH2 CH3 CH4* CH5* CH6* CH7* INT CLOCK CONTROL LOGIC OUTPUT SHIFT REGISTER ANALOG INPUT MUX SSTRB T/H COM REFOUT DOUT +2.048V REFERENCE CLOCK IN 8-BIT SAR ADC OUT REF VDD DGND MAX1110 MAX1111 AGND REFIN *MAX1110 ONLY Pin Configurations appear at end of data sheet. SPI and QSPI are trademarks of Motorola, Inc. MICROWIRE is a trademark of National Semiconductor Corp. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. 1 MAX1110/MAX1111 General Description MAX1110/MAX1111 +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs ABSOLUTE MAXIMUM RATINGS VDD to AGND ..............................................................-0.3V to 6V AGND to DGND .......................................................-0.3V to 0.3V CH0-CH7, COM, REFIN, REFOUT to AGND ......................................-0.3V to (VDD + 0.3V) Digital Inputs to DGND ...............................................-0.3V to 6V Digital Outputs to DGND ............................-0.3V to (VDD + 0.3V) Continuous Power Dissipation (TA = +70C) QSOP (derate 8.30mW/C above +70C) .....................667mW SSOP (derate 8.00mW/C above +70C) .....................640mW Operating Temperature Ranges MAX1110CAP/MAX1111CEE...............................0C to +70C MAX1110EAP/MAX1111EGE............................-40C to +85C Storage Temperature Range .............................-65C to +150C Lead Temperature (soldering, 10s) .................................+300C Soldering Temperature (reflow) .......................................+260C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VDD = 2.7V to 5.5V; unipolar input mode; VCOM = 0V; fSCLK = 500kHz, external clock (50% duty cycle); 10 clocks/conversion cycle (50ksps); 1F capacitor at REFOUT; TA = TMIN to TMAX; unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS DC ACCURACY Resolution 8 Relative Accuracy (Note 1) INL Differential Nonlinearity DNL Offset Error VDD = 2.7V to 3.6V 0.15 VDD = 5.5V (Note 2) 0.2 No missing codes over temperature 0.35 VDD = 5.5V (Note 2) 0.5 Internal or external reference Gain Temperature Coefficient External reference, 2.048V TUE 1 1 0.8 0.3 Channel-to-Channel Offset Matching 0.5 1 VDD = 2.7V to 3.6V Gain Error (Note 3) Total Unadjusted Error Bits LSB LSB LSB LSB ppm/C 1 LSB 0.1 LSB SINAD 49 dB Total Harmonic Distortion (up to the 5th harmonic) THD -70 dB Spurious-Free Dynamic Range SFDR 68 dB DYNAMIC SPECIFICATIONS (10.034kHz sine-wave input, 2.048VP-P, 50ksps, 500kHz external clock) Signal-to-Noise and Distortion Ratio Channel-to-Channel Crosstalk VCH_ = 2.048VP-P, 25kHz (Note 4) -75 dB Small-Signal Bandwidth -3dB rolloff 1.5 MHz 800 kHz Full-Power Bandwidth 2 _______________________________________________________________________________________ +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs (VDD = 2.7V to 5.5V; unipolar input mode; VCOM = 0V; fSCLK = 500kHz, external clock (50% duty cycle); 10 clocks/conversion cycle (50ksps); 1F capacitor at REFOUT; TA = TMIN to TMAX; unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN External clock, 500kHz, 10 clocks/conversion 20 External clock, 2MHz 1 TYP MAX 25 55 UNITS CONVERSION RATE Conversion Time (Note 5) tCONV Track/Hold Acquisition Time tACQ Internal clock s s Aperture Delay 10 Aperture Jitter <50 ps Internal Clock Frequency 400 kHz (Note 6) External Clock-Frequency Range 50 Used for data transfer only ns 500 kHz 2 MHz ANALOG INPUT Unipolar input, VCOM = 0V Input Voltage Range, SingleEnded and Differential (Note 7) 0 VREFIN VCOM VREFIN/2 Bipolar input, VCOM = VREFIN/2 Multiplexer Leakage Current On/off-leakage current, VCH_ = 0V or VDD 0.01 Input Capacitance 1 18 V V A pF INTERNAL REFERENCE REFOUT Voltage 1.968 2.048 2.128 V REFOUT Short-Circuit Current 3.5 mA REFOUT Temperature Coefficient 50 ppm/C 2.5 mV Load Regulation (Note 8) 0 to 0.5mA output load Capacitive Bypass at REFOUT 1 F EXTERNAL REFERENCE AT REFIN VDD + 0.05 1 Input Voltage Range Input Current (Note 9) 1 V 20 A 5.5 V POWER REQUIREMENTS Supply Voltage VDD Supply Current (Note 2) IDD 2.7 VDD = 2.7V to 3.6V Full-scale input CLOAD = 10pF Operating mode 85 Reference disabled 45 VDD = 5.5V Full-scale input CLOAD = 10pF Operating mode 120 Reference disabled 80 Power-down Power-Supply Rejection (Note 10) PSR Software SHDN at DGND VDD = 2.7V to 3.6V; external reference, 2.048V; full-scale input 250 250 A 2 3.2 10 0.4 4 mV _______________________________________________________________________________________ 3 MAX1110/MAX1111 ELECTRICAL CHARACTERISTICS (continued) MAX1110/MAX1111 +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs ELECTRICAL CHARACTERISTICS (continued) (VDD = 2.7V to 5.5V; unipolar input mode; VCOM = 0V; fSCLK = 500kHz, external clock (50% duty cycle); 10 clocks/conversion cycle (50ksps); 1F capacitor at REFOUT; TA = TMIN to TMAX; unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS DIGITAL INPUTS: DIN, SCLK, CS DIN, SCLK, CS Input High Voltage VIH DIN, SCLK, CS Input Low Voltage VIL DIN, SCLK, CS Input Hysteresis VDD 3.6V 2 VDD > 3.6V 3 V 0.8 VHYST 0.2 V V DIN, SCLK, CS Input Leakage IIN Digital inputs = 0V or VDD 1 A DIN, SCLK, CS Input Capacitance CIN (Note 6) 15 pF SHDN INPUT SHDN Input High Voltage VSH VDD - 0.4 SHDN Input Mid-Voltage VSM 1.1 SHDN Voltage, High Impedance VFLT SHDN Input Low Voltage VSL SHDN = open SHDN Input Current VSHDN = 0V or VDD SHDN Maximum Allowed Leakage for Mid-Input SHDN = open V VDD - 1.1 VDD/2 V V 0.4 V 4 A 100 nA DIGITAL OUTPUTS: DOUT, SSTRB Output Low Voltage VOL Output High Voltage VOH Three-State Leakage Current Three-State Output Capacitance 4 IL COUT ISINK = 5mA 0.4 ISINK = 16mA 0.8 ISOURCE = 0.5mA CS = VDD VDD - 0.5 V V 0.01 CS = VDD (Note 6) _______________________________________________________________________________________ 10 A 15 pF +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs (VDD = 2.7V to 5.5V, TA = TMIN to TMAX, unless otherwise noted.) PARAMETER Track/Hold Acquisition Time DIN to SCLK Setup SYMBOL CONDITIONS TYP MAX UNITS 1 s tDS 100 ns DIN to SCLK Hold tDH SCLK Fall to Output Data Valid tDO Figure 1, CLOAD = 100pF CS Fall to Output Enable tDV Figure 1, CLOAD = 100pF tTR Figure 2, CLOAD = 100pF CS Rise to Output Disable MIN tACQ 0 ns 20 200 ns 240 ns 240 ns CS to SCLK Rise Setup tCSS 100 ns CS to SCLK Rise Hold tCSH 0 ns SCLK Pulse Width High tCH 200 ns SCLK Pulse Width Low tCL 200 SCLK Fall to SSTRB t SSTRB ns CLOAD = 100pF 240 ns CS Fall to SSTRB Output Enable (Note 6) tSDV Figure 1, external clock mode only, CLOAD = 100pF 240 ns CS Rise to SSTRB output Disable (Note 6) tSTR Figure 2, external clock mode only, CLOAD = 100pF 240 ns SSTRB Rise to SCLK Rise (Note 6) tSCK Figure 11, internal clock mode only Wake-Up Time Note 1: Note 2: Note 3: Note 4: Note 5: Note 6: Note 7: Note 8: Note 9: Note 10: Note 11: tWAKE 0 ns External reference 20 s Internal reference (Note 11) 12 ms Relative accuracy is the analog value's deviation (at any code) from its theoretical value after the full-scale range is calibrated. See Typical Operating Characteristics. VREFIN = 2.048V, offset nulled. On-channel grounded; sine wave applied to all off-channels. Conversion time is defined as the number of clock cycles multiplied by the clock period; clock has 50% duty cycle. Guaranteed by design. Not subject to production testing. Common-mode range for the analog inputs is from AGND to VDD. External load should not change during the conversion for specified accuracy. External reference at 2.048V, full-scale input, 500kHz external clock. Measured as | VFS (2.7V) - VFS (3.6V) |. 1F at REFOUT; internal reference settling to 0.5 LSB. _______________________________________________________________________________________ 5 MAX1110/MAX1111 TIMING CHARACTERISTICS (Figures 8 and 9) __________________________________________Typical Operating Characteristics (VDD = 2.7V; fSCLK = 500kHz; external clock (50% duty cycle); RL = ; TA = +25C, unless otherwise noted.) SUPPLY CURRENT (A) 140 300 250 CLOAD = 60pF 200 150 100 3.0 VDD = 5.5V 100 VDD = 3.6V 5.0 4.0 4.5 5.0 5.5 6.0 SHDN = DGND 4.5 4.0 3.5 3.0 2.5 2.0 60 3.5 -60 -20 20 60 100 -60 140 -20 20 60 100 SUPPLY VOLTAGE (V) TEMPERATURE (C) TEMPERATURE (C) OFFSET ERROR vs. SUPPLY VOLTAGE INTEGRAL NONLINEARITY vs. SUPPLY VOLTAGE DIFFERENTIAL NONLINEARITY vs. CODE 0.2 0.4 0.6 MAX1110-06 0.7 140 0.3 MAX1110-05 0.5 MAX1110-04 0.8 0.1 0.4 0.3 0.3 DNL (LSB) 0.5 INL (LSB) 0.2 0 -0.1 0.2 0.1 -0.2 0.1 0 -0.3 0 3.0 3.5 4.0 4.5 5.0 5.5 6.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 SUPPLY VOLTAGE (V) SUPPLY VOLTAGE (V) OFFSET ERROR vs. TEMPERATURE INTEGRAL NONLINEARITY vs. CODE 0.5 64 128 192 256 DIGITAL CODE 0.20 MAX1110-07 0.6 0 6.0 FFT PLOT 20 MAX1110-08 2.5 0.15 fCH_ = 10.034kHz, 2VP-P fSAMPLE = 50ksps 0 MAX1110-09 OFFSET ERROR (LSB) 120 80 CLOAD = 30pF 2.5 MAX1110-02 350 OUTPUT CODE = FULL SCALE CLOAD = 10pF SHUTDOWN SUPPLY CURRENT (A) OUTPUT CODE = 10101010 SUPPLY CURRENT (A) 160 MAX1110-01 400 SHUTDOWN SUPPLY CURRENT vs. TEMPERATURE SUPPLY CURRENT vs. TEMPERATURE MAX1110-03 SUPPLY CURRENT vs. SUPPLY VOLTAGE 0.3 AMPLITUDE (dB) 0.10 0.4 INL (LSB) OFFSET ERROR (LSB) MAX1110/MAX1111 +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs 0.05 0 -0.05 0.2 -20 -40 -60 -0.10 0.1 0 -0.20 -60 -20 20 60 TEMPERATURE (C) 6 -80 -0.15 100 140 -100 0 64 128 DIGITAL CODE 192 256 0 5 10 15 FREQUENCY (kHz) _______________________________________________________________________________________ 20 25 +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs PIN NAME FUNCTION MAX1110 MAX1111 1-4 1-4 CH0-CH3 Sampling Analog Inputs 5-8 -- CH4-CH7 Sampling Analog Inputs 9 5 COM Ground Reference for Analog Inputs. Sets zero-code voltage in single-ended mode. Must be stable to 0.5 LSB. 10 6 SHDN Three-Level Shutdown Input. Normally high impedance. Pulling SHDN low shuts the MAX1110/MAX1111 down to 10A (max) supply current; otherwise, the devices are fully operational. Pulling SHDN high shuts down the internal reference. 11 7 REFIN Reference Voltage Input for Analog-to-Digital Conversion. Connect to REFOUT to use the internal reference. 12 8 REFOUT Internal Reference Generator Output. Bypass with a 1F capacitor to AGND. 13 9 AGND Analog Ground 14 10 DGND Digital Ground 15 11 DOUT Serial-Data Output. Data is clocked out on SCLK's falling edge. High impedance when CS is high. 16 12 SSTRB Serial-Strobe Output. In internal clock mode, SSTRB goes low when the MAX1110/ MAX1111 begin the A/D conversion and goes high when the conversion is done. In external clock mode, SSTRB pulses high for two clock periods before the MSB is shifted out. High impedance when CS is high (external clock mode only). 17 13 DIN Serial-Data Input. Data is clocked in at SCLK's rising edge. The voltage at DIN can exceed VDD (up to 5.5V). 18 14 CS Active-Low Chip Select. Data is not clocked into DIN unless CS is low. When CS is high, DOUT is high impedance. The voltage at CS can exceed VDD (up to 5.5V). 19 15 SCLK 20 16 VDD Serial-Clock Input. Clocks data in and out of serial interface. In external clock mode, SCLK also sets the conversion speed (duty cycle must be 45% to 55%). The voltage at SCLK can exceed VDD (up to 5.5V). Positive Supply Voltage, 2.7V to 5.5V +3V +3V DOUT DOUT 3k 3k CLOAD CLOAD DGND DGND a) High-Z to VOH and VOL to VOH b) High-Z to VOL and VOH to VOL Figure 1. Load Circuits for Enable Time 3k DOUT DOUT 3k CLOAD DGND a) VOH to High-Z CLOAD DGND b) VOL to High-Z Figure 2. Load Circuits for Disable Time _______________________________________________________________________________________ 7 MAX1110/MAX1111 ______________________________________________________________Pin Description MAX1110/MAX1111 +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs _______________Detailed Description The MAX1110/MAX1111 analog-to-digital converters (ADCs) use a successive-approximation conversion technique and input track/hold (T/H) circuitry to convert an analog signal to an 8-bit digital output. A flexible serial interface provides easy interface to microprocessors (Ps). Figure 3 shows the Typical Operating Circuit. Pseudo-Differential Input The sampling architecture of the ADC's analog comparator is illustrated in Figure 4, the equivalent input circuit. In single-ended mode, IN+ is internally switched to the selected input channel, CH_, and IN- is switched to COM. In differential mode, IN+ and IN- are selected from the following pairs: CH0/CH1, CH2/CH3, CH4/CH5, and CH6/CH7. Configure the MAX1110 channels with Table 1 and the MAX1111 channels with Table 2. In differential mode, IN- and IN+ are internally switched to either of the analog inputs. This configuration is pseudo-differential to the effect that only the signal at IN+ is sampled. The return side (IN-) must remain stable within 0.5 LSB (0.1 LSB for best results) with respect to AGND during a conversion. To accomplish this, connect a 0.1F capacitor from IN- (the selected analog input) to AGND. During the acquisition interval, the channel selected as the positive input (IN+) charges capacitor CHOLD. The acquisition interval spans two SCLK cycles and ends on the falling SCLK edge after the last bit of the input control word has been entered. At the end of the acquisition interval, the T/H switch opens, retaining charge on CHOLD as a sample of the signal at IN+. The conversion interval begins with the input multiplexer switching CHOLD from the positive input (IN+) to the negative input (IN-). In single-ended mode, IN- is simply COM. This unbalances node ZERO at the input of the comparator. The capacitive DAC adjusts during the remainder of the conversion cycle to restore node ZERO to 0V within the limits of 8-bit resolution. This action is equivalent to transferring a charge of 18pF x (VIN+ - VIN-) from CHOLD to the binary-weighted capacitive DAC, which in turn forms a digital representation of the analog input signal. Track/Hold The T/H enters its tracking mode on the falling clock edge after the sixth bit of the 8-bit control byte has been shifted in. It enters its hold mode on the falling clock edge after the eighth bit of the control byte has been shifted in. If the converter is set up for singleended inputs, IN- is connected to COM, and the converter samples the "+" input; if it is set up for differential inputs, IN- connects to the "-" input, and the difference (IN+ - IN-) is sampled. At the end of the conversion, the positive input connects back to IN+, and C HOLD charges to the input signal. +2.7V VDD VDD CH0 0.1F ANALOG INPUTS CH7 CAPACITIVE DAC REFIN 1F AGND DGND COM CH0 CH1 CPU REFOUT REFIN 1F CS SCLK DIN DOUT CH4* I/O SCK (SK) MOSI (SO) MISO (SI) SSTRB SHDN Figure 3. Typical Operating Circuit 8 VSS CH5* CH6* CH7* ZERO 18pF CH2 CH3 MAX1110 MAX1111 COMPARATOR CHOLD INPUT MUX - + 6.5k RIN CSWITCH TRACK T/H SWITCH COM HOLD AT THE SAMPLING INSTANT, THE MUX INPUT SWITCHES FROM THE SELECTED IN+ CHANNEL TO THE SELECTED IN- CHANNEL. SINGLE-ENDED MODE: IN+ = CHO-CH7, IN- = COM. DIFFERENTIAL MODE: IN+ AND IN- SELECTED FROM PAIRS OF CH0/CH1, CH2/CH3, CH4*/CH5*, CH6*/CH7*. *MAX1110 ONLY Figure 4. Equivalent Input Circuit _______________________________________________________________________________________ +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs MAX1110/MAX1111 Table 1a. MAX1110 Channel Selection in Single-Ended Mode (SGL/DIF = 1) SEL2 SEL1 SEL0 CH0 0 0 0 + 1 0 0 0 0 1 1 0 1 0 1 0 1 1 0 0 1 1 1 1 1 CH1 CH2 CH3 CH4 CH5 CH6 CH7 COM - + - + - + - + - + - + - + - Table 1b. MAX1110 Channel Selection in Differential Mode (SGL/DIF = 0) SEL2 SEL1 SEL0 CH0 CH1 0 0 0 + - 0 0 1 0 1 0 0 1 1 1 0 0 1 0 1 1 1 0 1 1 1 - CH2 CH3 + - CH4 CH5 + - CH6 CH7 + - - + + - + - + Table 2a. MAX1111 Channel Selection in Single-Ended Mode (SGL/DIF = 1) SEL2 SEL1 SEL0 CH0 0 0 X + 1 0 X 0 1 X 1 1 X CH1 CH2 CH3 COM - + - + - + - Table 2b. MAX1111 Channel Selection in Differential Mode (SGL/DIF = 0) SEL2 SEL1 SEL0 CH0 CH1 0 0 X + - 0 1 X 1 0 X - + 1 1 X CH2 CH3 + - - + _______________________________________________________________________________________ 9 MAX1110/MAX1111 +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs The time required for the T/H to acquire an input signal is a function of how quickly its input capacitance is charged. If the input signal's source impedance is high, the acquisition time lengthens, and more time must be allowed between conversions. The acquisition time, tACQ, is the minimum time needed for the signal to be acquired. It is calculated by: tACQ = 6 x (RS + RIN) x 18pF where RIN = 6.5k, RS = the source impedance of the input signal, and tACQ is never less than 1s. Note that source impedances below 2.4k do not significantly affect the AC performance of the ADC. Input Bandwidth The ADC's input tracking circuitry has a 1.5MHz smallsignal bandwidth, so it is possible to digitize highspeed transient events and measure periodic signals with bandwidths exceeding the ADC's sampling rate by using undersampling techniques. To avoid highfrequency signals being aliased into the frequency band of interest, anti-alias filtering is recommended. Analog Inputs Internal protection diodes, which clamp the analog input to VDD and AGND, allow the channel input pins to swing from (AGND - 0.3V) to (VDD + 0.3V) without dam- age. However, for accurate conversions near full scale, the inputs must not exceed VDD by more than 50mV or be lower than AGND by 50mV. If the analog input exceeds 50mV beyond the supplies, do not forward bias the protection diodes of off channels over 2mA. The MAX1110/MAX1111 can be configured for differential or single-ended inputs with bits 2 and 3 of the control byte (Table 3). In single-ended mode, the analog inputs are internally referenced to COM with a full-scale input range from COM to VREFIN + COM. For bipolar operation, set COM to VREFIN/2. In differential mode, choosing unipolar mode sets the differential input range at 0V to V REFIN. In unipolar mode, the output code is invalid (code zero) when a negative differential input voltage is applied. Bipolar mode sets the differential input range to VREFIN/2. Note that in this mode, the common-mode input range includes both supply rails. Refer to Table 4 for input voltage ranges. Quick Look To quickly evaluate the MAX1110/MAX1111's analog performance, use the circuit of Figure 5. The MAX1110/MAX1111 require a control byte to be written to DIN before each conversion. Tying DIN to +3V feeds Table 3. Control-Byte Format 10 BIT 7 (MSB) BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 (LSB) START SEL2 SEL1 SEL0 UNI/BIP SGL/DIF PD1 PD0 BIT NAME 7 (MSB) START 6 5 4 SEL2 SEL1 SEL0 3 UNI/BIP 1 = unipolar, 0 = bipolar. Selects unipolar or bipolar conversion mode. Select differential operation if bipolar mode is used (Table 4). 2 SGL/DIF 1 = single ended, 0 = differential. Selects single-ended or differential conversions. In singleended mode, input signal voltages are referred to COM. In differential mode, the voltage difference between two channels is measured (Tables 1 and 2). 1 PD1 1 = fully operational, 0 = power-down. Selects fully operational or power-down mode. 0 (LSB) PD0 1 = external clock mode, 0 = internal clock mode. Selects external or internal clock mode. DESCRIPTION The first logic "1" bit after CS goes low defines the beginning of the control byte. Select which of the input channels are to be used for the conversion (Tables 1 and 2). ______________________________________________________________________________________ +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs UNIPOLAR MODE BIPOLAR MODE Full Scale Zero Scale Positive Full Scale Zero Scale Negative Full Scale VREFIN + COM COM +VREFIN/2 + COM COM -VREFIN/2 + COM in control bytes of $FF (hex), which trigger singleended, unipolar conversions on CH7 (MAX1110) or CH3 (MAX1111) in external clock mode without powering down between conversions. In external clock mode, the SSTRB output pulses high for two clock periods before the most significant bit of the 8-bit conversion result is shifted out of DOUT. Varying the analog input alters the output code. A total of 10 clock cycles is required per conversion. All transitions of the SSTRB and DOUT outputs occur on SCLK's falling edge. How to Start a Conversion A conversion is started by clocking a control byte into DIN. With CS low, each rising edge on SCLK clocks a bit from DIN into the MAX1110/MAX1111's internal shift reg- ister. After CS falls, the first arriving logic "1" bit at DIN defines the MSB of the control byte. Until this first start bit arrives, any number of logic "0" bits can be clocked into DIN with no effect. Table 3 shows the control-byte format. The MAX1110/MAX1111 are compatible with MICROWIRE, SPI, and QSPI devices. For SPI, select the correct clock polarity and sampling edge in the SPI control registers: set CPOL = 0 and CPHA = 0. MICROWIRE, SPI, and QSPI all transmit a byte and receive a byte at the same time. Using the Typical Operating Circuit (Figure 3), the simplest software interface requires three 8-bit transfers to perform a conversion (one 8-bit transfer to configure the ADC, and two more 8-bit transfers to clock out the 8-bit conversion result). Figure 6 shows the MAX1110/ MAX1111 common serial-interface connections. VDD OSCILLOSCOPE +3V 0.1F 1F SCLK DGND MAX1110 MAX1111 0V TO +2.048V ANALOG 0.01F INPUT CH7 (CH3) AGND SSTRB CS DOUT* SCLK COM +3V DIN 500kHz OSCILLATOR CH1 CH2 CH3 CH4 SSTRB REFOUT DOUT REFIN SHDN N.C. C1 1F *FULL-SCALE ANALOG INPUT, CONVERSION RESULT = $FF (HEX) ( ) ARE FOR THE MAX1111. Figure 5. Quick-Look Circuit ______________________________________________________________________________________ 11 MAX1110/MAX1111 Table 4. Full-Scale and Zero-Scale Voltages MAX1110/MAX1111 +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs I/O Simple Software Interface Make sure the CPU's serial interface runs in master mode so the CPU generates the serial clock. Choose a clock frequency from 50kHz to 500kHz. 1) Set up the control byte for external clock mode and call it TB1. TB1 should be of the format 1XXXXX11 binary, where the Xs denote the particular channel and conversion mode selected. 2) Use a general-purpose I/O line on the CPU to pull CS low. 3) Transmit TB1 and, simultaneously, receive a byte and call it RB1. Ignore RB1. CS SCK SCLK MISO DOUT +3V MAX1110 MAX1111 SS a) SPI CS CS SCK SCLK MISO 4) Transmit a byte of all zeros ($00 hex) and, simultaneously, receive byte RB2. 5) Transmit a byte of all zeros ($00 hex) and, simultaneously, receive byte RB3. DOUT +3V MAX1110 MAX1111 SS 6) Pull CS high. Figure 7 shows the timing for this sequence. Bytes RB2 and RB3 contain the result of the conversion padded with two leading zeros and six trailing zeros. The total conversion time is a function of the serial-clock frequency and the amount of idle time between 8-bit transfers. Make sure that the total conversion time does not exceed 1ms, to avoid excessive T/H droop. b) QSPI I/O CS SK SCLK SI DOUT MAX1110 MAX1111 Digital Inputs CS, SCLK, and DIN can accept input signals up to 5.5V, regardless of the supply voltages. This allows the MAX1110/MAX1111 to accept digital inputs from both 3V and 5V systems. c) MICROWIRE Figure 6. Common Serial-Interface Connections to the MAX1110/MAX1111 CS tACQ SCLK 1 4 SEL2 SEL1 SEL0 UNI/ BIP DIN 8 SGL/ PD1 DIF 12 16 20 24 PD0 START SSTRB A/D STATE B7 IDLE RB3 RB2 RB1 DOUT B6 ACQUISITION 4s B5 B4 B3 B2 B1 B0 FILLED WITH ZEROS CONVERSION (fSCLK = 500kHz) Figure 7. Single-Conversion Timing, External Clock Mode, 24 Clocks 12 ______________________________________________________________________________________ IDLE +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs conversion steps. SSTRB pulses high for two clock periods after the last bit of the control byte. Successiveapproximation bit decisions are made and appear at DOUT on each of the next eight SCLK falling edges (Figure 7). After the eight data bits are clocked out, subsequent clock pulses clock out zeros from the DOUT pin. Clock Modes The MAX1110/MAX1111 can use either an external serial clock or the internal clock to perform the successiveapproximation conversion. In both clock modes, the external clock shifts data in and out of the devices. Bit PD0 of the control byte programs the clock mode. Figures 8-11 show the timing characteristics common to both modes. SSTRB and DOUT go into a high-impedance state when CS goes high; after the next CS falling edge, SSTRB outputs a logic low. Figure 9 shows the SSTRB timing in external clock mode. The conversion must complete in 1ms, or droop on the sample-and-hold capacitors can degrade conversion results. Use internal clock mode if the serial-clock frequency is less than 50kHz, or if serial-clock interruptions could cause the conversion interval to exceed 1ms. External Clock In external clock mode, the external clock not only shifts data in and out, it also drives the analog-to-digital CS *** tCSH tCSS tCL tCH SCLK tCSH *** tDS tDH *** DIN tDO tDV tDO tTR *** DOUT Figure 8. Detailed Serial-Interface Timing CS *** *** tSTR tSDV SSTRB *** *** tSSTRB SCLK tSSTRB **** **** PD0 CLOCKED IN Figure 9. External Clock Mode SSTRB Detailed Timing ______________________________________________________________________________________ 13 MAX1110/MAX1111 Digital Output In unipolar input mode, the output is straight binary (Figure 15). For bipolar inputs, the output is two's-complement (Figure 16). Data is clocked out at SCLK's falling edge in MSB-first format. MAX1110/MAX1111 +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs CS SCLK DIN 1 2 3 4 5 SEL2 SEL1 SEL0 UNI/ BIP 7 8 SGL/ PD1 DIF PD0 6 9 10 11 12 15 16 17 18 START SSTRB tCONV DOUT A/D STATE B7 B6 B1 B0 FILLED WITH ZEROS CONVERSION 25s TYP IDLE IDLE tACQ 4s (fSCLK = 500kHz) Figure 10. Internal Clock Mode Timing CS tCONV tCSS tSCK tCSH SSTRB tSSTRB SCLK PD0 CLOCK IN NOTE: FOR BEST NOISE PERFORMANCE, KEEP SCLK LOW DURING CONVERSION. Figure 11. Internal Clock Mode SSTRB Detailed Timing Internal Clock Internal clock mode frees the P from the burden of running the SAR conversion clock. This allows the conversion results to be read back at the processor's convenience, at any clock rate up to 2MHz. SSTRB goes low at the start of the conversion and then goes high when the conversion is complete. SSTRB is low for 25s (typ), during which time SCLK should remain low for best noise performance. An internal register stores data when the conversion is in progress. SCLK clocks the data out of this register at any time after the conversion is complete. After SSTRB goes high, the second falling clock edge produces the MSB of the conversion at DOUT, followed by the 14 remaining bits in MSB-first format (Figure 10). CS does not need to be held low once a conversion is started. Pulling CS high prevents data from being clocked into the MAX1110/MAX1111 and three-states DOUT, but it does not adversely affect an internal clock-mode conversion already in progress. When internal clock mode is selected, SSTRB does not go into a high-impedance state when CS goes high. Figure 11 shows the SSTRB timing in internal clock mode. In this mode, data can be shifted in and out of the MAX1110/MAX1111 at clock rates up to 2MHz, provided that the minimum acquisition time, tACQ, is kept above 1s. ______________________________________________________________________________________ +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs MAX1110/MAX1111 CS 1 8 10 1 8 10 1 8 10 1 SCLK S DIN CONTROL BYTE 0 S B7 DOUT S CONTROL BYTE 1 B0 B7 B0 CONVERSION RESULT 1 CONVERSION RESULT 0 S CONTROL BYTE 2 CONTROL BYTE 3 B7 CONVERSION RESULT 2 SSTRB Figure 12a. Continuous Conversions, External Clock Mode, 10 Clocks/Conversion Timing CS SCLK DIN DOUT S S CONTROL BYTE 0 B7 CONTROL BYTE 1 B0 CONVERSION RESULT 0 B7 CONVERSION RESULT 1 Figure 12b. Continuous Conversions, External Clock Mode, 16 Clocks/Conversion Timing Data Framing The falling edge of CS does not start a conversion. The first logic high clocked into DIN is interpreted as a start bit and defines the first bit of the control byte. A conversion starts on the falling edge of SCLK, after the eighth bit of the control byte (the PD0 bit) is clocked into DIN. The start bit is defined as: The first high bit clocked into DIN with CS low any time the converter is idle; e.g., after VDD is applied. OR The first high bit clocked into DIN after the MSB of a conversion in progress is clocked onto the DOUT pin. If CS is toggled before the current conversion is complete, then the next high bit clocked into DIN is recognized as a start bit; the current conversion is terminated, and a new one is started. The fastest the MAX1110/MAX1111 can run is 10 clocks per conversion. Figure 12a shows the serialinterface timing necessary to perform a conversion every 10 SCLK cycles in external clock mode. Many microcontrollers require that conversions occur in multiples of eight SCLK clocks; 16 clocks per conversion is typically the fastest that a microcontroller can drive the MAX1110/MAX1111. Figure 12b shows the serial-interface timing necessary to perform a conversion every 16 SCLK cycles in external clock mode. ______________________________________________________________________________________ 15 Power-On Reset When power is first applied, and if SHDN is not pulled low, internal power-on reset circuitry activates the MAX1110/MAX1111 in internal clock mode. SSTRB is high on power-up and, if CS is low, the first logical 1 on DIN is interpreted as a start bit. Until a conversion takes place, DOUT shifts out zeros. No conversions should be performed until the reference voltage has stabilized (see Electrical Characteristics). Power-Down When operating at speeds below the maximum sampling rate, the MAX1110/MAX1111's automatic powerdown mode can save considerable power by placing the converters in a low-current shutdown state between conversions. Figure 13 shows the average supply current as a function of the sampling rate. Select power-down with PD1 of the DIN control byte with SHDN high or high impedance (Table 3). Pull SHDN low at any time to shut down the converters completely. SHDN overrides PD1 of the control byte. Figures 14a and 14b illustrate the various power-down sequences in both external and internal clock modes. Software Power-Down Software power-down is activated using bit PD1 of the control byte. When software power-down is asserted, the ADCs continue to operate in the last specified clock mode until the conversion is complete. The ADCs then power down into a low quiescent-current state. In internal clock mode, the interface remains active, and conversion results can be clocked out after the MAX1110/ MAX1111 have entered a software power-down. The first logical 1 on DIN is interpreted as a start bit, which powers up the MAX1110/MAX1111. If the DIN byte contains PD1 = 1, then the chip remains powered up. If PD1 = 0, power-down resumes after one conversion. Hard-Wired Power-Down Pulling SHDN low places the converters in hard-wired power-down. Unlike software power-down, the conversion is not completed; it stops coincidentally with SHDN being brought low. SHDN also controls the state of the internal reference (Table 5). Letting SHDN high impedance enables the internal 2.048V voltage reference. When returning to normal operation with SHDN high impedance, there is a tRC delay of approximately 1M x CLOAD, where CLOAD is the capacitive loading on the SHDN pin. Pulling SHDN high disables the internal reference, which saves power when using an external reference. External Reference An external reference between 1V and VDD should be connected directly at the REFIN terminal. The DC input impedance at REFIN is extremely high, consisting of leakage current only (typically 10nA). During a conversion, the reference must be able to deliver up to 20A average load current and have an output impedance of 1k or less at the conversion clock frequency. If the reference has higher output impedance or is noisy, bypass it close to the REFIN pin with a 0.1F capacitor. If an external reference is used with the MAX1110/ MAX1111, connect SHDN to VDD to disable the internal reference and decrease power consumption. 1000 MAX1110-fig13 Applications Information CLOAD = 60pF CODE = 10101010 SUPPLY CURRENT (A) MAX1110/MAX1111 +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs 100 CLOAD = 30pF CODE = 10101010 CLOAD = 30pF CODE = 11111111 10 Table 5. Hard-Wired Power-Down and Internal Reference State VDD = VREFIN = 3V CLOAD AT DOUT AND SSTRB 1 SHDN STATE DEVICE MODE INTERNAL REFERENCE 1 Enabled Disabled High Impedance Enabled Enabled 0 Power-Down Disabled 16 0 10 20 30 40 50 SAMPLING RATE (ksps) Figure 13. Average Supply Current vs. Sampling Rate ______________________________________________________________________________________ +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs INTERNAL EXTERNAL MAX1110/MAX1111 CLOCK MODE EXTERNAL SHDN SETS POWERDOWN MODE SETS EXTERNAL CLOCK MODE DIN S X X X X X 1 1 S X X X X X 0 1 S X X X X X 1 1 DATA VALID DATA VALID DOUT DATA INVALID POWERDOWN POWERED UP MODE SETS EXTERNAL CLOCK MODE POWERDOWN POWERED UP POWERED UP Figure 14a. Power-Down Modes, External Clock Timing Diagram INTERNAL CLOCK MODE SETS POWER-DOWN MODE SETS INTERNAL CLOCK MODE DIN S X X X X X 1 0 S X X X X X 0 0 MODE DATA VALID DATA VALID DOUT SSTRB S CONVERSION CONVERSION POWERED UP POWER-DOWN POWERED UP Figure 14b. Power-Down Modes, Internal Clock Timing Diagram Internal Reference Transfer Function To use the MAX1110/MAX1111 with the internal reference, connect REFIN to REFOUT. The full-scale range of the MAX1110/MAX1111 with the internal reference is typically 2.048V with unipolar inputs, and 1.024V with bipolar inputs. The internal reference should be bypassed to AGND with a 1F capacitor placed as close to the REFIN pin as possible. Table 4 shows the full-scale voltage ranges for unipolar and bipolar modes. Figure 15 depicts the nominal, unipolar I/O transfer function, and Figure 16 shows the bipolar I/O transfer function when using a 2.048V reference. Code transitions occur at integer LSB values. Output coding is binary, with 1 LSB = 8mV (2.048V/256) for unipolar operation and 1 LSB = 8mV [(2.048V/2 - -2.048V/2)/256] for bipolar operation. ______________________________________________________________________________________ 17 MAX1110/MAX1111 +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs OUTPUT CODE FULL-SCALE TRANSITION 11111111 SUPPLIES 11111110 +3V GND 11111101 FS = VREFIN + COM 1LSB = VREFIN 256 00000011 R* = 10 VDD 00000010 AGND DGND +3V DGND 00000001 00000000 0 (COM) 1 2 3 MAX1110 MAX1111 FS INPUT VOLTAGE (LSB) FS - 1LSB DIGITAL CIRCUITRY * OPTIONAL Figure 17. Power-Supply Grounding Connections Figure 15. Unipolar Transfer Function Layout, Grounding, and Bypassing For best performance, use printed circuit boards. Wirewrap boards are not recommended. Board layout should ensure that digital and analog signal lines are separated from each other. Do not run analog and digital (especially clock) lines parallel to one another, or digital lines underneath the ADC package. Figure 17 shows the recommended system ground connections. A single-point analog ground (star ground point) should be established at AGND, separate from the logic ground. Connect all other analog grounds and DGND to the star ground. No other digital system ground should be connected to this ground. The ground return to the power supply for the star ground should be low impedance and as short as possible for noise-free operation. OUTPUT CODE 01111111 01111110 00000010 00000001 00000000 V +FS = REFIN + COM 2 VREFIN COM = 2 -V -FS = REFIN + COM 2 VREFIN 1LSB = 256 11111111 11111110 11111101 10000001 10000000 -FS COM INPUT VOLTAGE (LSB) 1 +FS - 2 LSB High-frequency noise in the VDD power supply can affect the comparator in the ADC. Bypass the supply to the star ground with 0.1F and 1F capacitors close to the V DD pin of the MAX1110/MAX1111. Minimize capacitor lead lengths for best supply-noise rejection. If the +3V power supply is very noisy, a 10 resistor can be connected to form a lowpass filter. Figure 16. Bipolar Transfer Function 18 ______________________________________________________________________________________ +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs TOP VIEW + CH0 1 20 VDD + 19 SCLK CH0 1 16 VDD CH2 3 18 CS CH1 2 15 SCLK CH3 4 17 DIN CH2 3 14 CS CH1 2 MAX1110 MAX1111 16 SSTRB CH3 4 CH5 6 15 DOUT COM 5 12 SSTRB CH6 7 14 DGND SHDN 6 11 DOUT CH7 8 13 AGND REFIN 7 10 DGND CH4 5 COM 9 REFOUT 8 12 REFOUT SHDN 10 13 DIN 9 11 REFIN AGND QSOP SSOP Ordering Information PART MAX1110CAP+ MAX1110C/D TEMP RANGE 0C to +70C 0C to +70C Chip Information PIN-PACKAGE PROCESS: CMOS 20 SSOP SUBSTRATE CONNECTED TO DGND Dice* MAX1110EAP+ -40C to +85C 20 SSOP MAX1111CEE+ 0C to +70C 16 QSOP MAX1111EEE+ -40C to +85C 16 QSOP MAX1111EEE/V+ -40C to +85C 16 QSOP *Dice are specified at TA = +25C, DC parameters only. +Denotes a lead(Pb)-free/RoHS-compliant package. /V denotes an automotive qualified part. Package Information For the latest package outline information and land patterns (footnote), go to www.maxim-ic.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO. 20 SSOP A20+1 21-0056 90-0094 16 QSOP E16+1 21-0055 90-0167 ______________________________________________________________________________________ 19 MAX1110/MAX1111 Pin Configurations MAX1110/MAX1111 +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs Revision History REVISION NUMBER REVISION DATE 3 2/10 Added automotive qualified part to data sheet 4/11 Removed PDIP packages from data sheet. Revised Timing Characteristics table and included style updates throughout data sheet. 4 DESCRIPTION PAGES CHANGED 19 1-7, 10, 13, 14, 16, 18, 19 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 20 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 2011 Maxim Integrated Products Maxim is a registered trademark of Maxim Integrated Products, Inc.