Amplifiers for infrared detectors C4159/C5185 series C3757-02 Low noise amplifiers for infrared detector (InSb, InAs, InGaAs, MCT, PbS, PbSe) Accessories Instruction manual Power cable (one end with 4-pin connector for connection to amplifier and the other end unterminated, 2 m) A4372-02 Required power supply specifications * * * * * C4159 series: 15 V (12.0 to 17.5 V can also be used) C5185 series: 15 V (15.0 to 17.5 V can also be used) Power supply voltage: 1.5 times or more of amplifier's maximum current consumption Ripple noise: 5 mVp-p or less Analog power supply only Absolute maximum ratings (Ta=25 C) Parameter Operating temperature Storage temperature Value 0 to +40 -20 to +70 Unit C C Amplifiers for photovoltaic detectors (Typ.) Parameter Applicable detector Conversion impedance Frequency response (amp only, -3 dB) Output impedance Maximum output voltage (1 k load) Output offset voltage Equivalent input noise current (f=1 kHz) Reverse voltage External power supply Current consumption *2 C4159-01 C4159-04 C4159-05 InSb (dewar type) *1 InSb (dewar type) *1 InAs (dewar type) (P5968-060, P5968-100) (P5968-200) (P7163) 108, 107, 106 2 x 107, 2 x 106, 2 x 105 108, 107, 106 (3 ranges switchable) (3 ranges switchable) (3 ranges switchable) C4159-06 InAs (P10090 series) 106, 105, 104 (3 ranges switchable) Unit V/A DC to 100 kHz DC to 45 kHz DC to 15 kHz DC to 100 kHz - 50 50 50 50 +10 +10 +10 +10 V 5 0.15 (108, 107 range) 0.65 (106 range) 5 5 mV 6 pA/Hz1/2 +30, -22 Max. V mA 10 0.15 (108, 107 range) 0.55 0.65 (106 range) Impossible 15 +30, -10 Max. Note: Output noise voltage = Equivalent input noise current x Conversion impedance *1: Custom types for multi-element detectors are also available. *2: Recommended DC power supply (analog power supply): 15 V Current capacity: More than 1.5 times the maximum current consumption Ripple noise: 5 mVp-p or less www.hamamatsu.com 1 Amplifiers for infrared detectors C4159/C5185 series, C3757-02 Amplifiers for InGaAs PIN photodiodes (Typ.) Parameter Applicable detector Conversion impedance Frequency response (amp only, -3 dB) Output impedance Maximum output voltage (1 k load) Output offset voltage Equivalent input noise current (f=1 kHz) Reverse voltage External power supply Current consumption *2 C4159-02 InGaAs 250 to 5 x 103 continuous C4159-03 InGaAs 107, 106, 105 (3 ranges switchable) Unit - 20 Hz to 120 MHz DC to 15 kHz - 50 50 1.3 +10 V 30 5 mV 30 2.5 pA/Hz1/2 Internally generated 15 +90, -60 Max. Can be applied from external unit 15 15 Max. V mA V/A Amplifiers for photoconductive detectors (Typ.) Parameter Applicable detector Input impedance Voltage gain Frequency response (amp only, -3 dB) Detector bias current Output impedance Maximum output voltage (1 k load) Equivalent input noise voltage (f=1 kHz) External power supply Current consumption *2 C5185 MCT (dewar type), InSb (P6606 series) 5 66 (x 2000) C5185-01 MCT (P3981/P2750 series) *3 5 66 (x 2000) C3757-02 Unit PbS, PbSe - 10000 40 (x 100) k dB 0.2 Hz to 10 kHz - Internal bias - 50 5 Hz to 250 kHz 5 Hz to 250 kHz 5 mA, 10 mA, 15 mA (3 ranges switchable) 50 0.1 mA, 0.5 mA, 1 mA (3 ranges switchable) 50 2.5 2.5 10 V 2.6 1.2 40 nV/Hz1/2 15 +60, -10 Max. 15 +60, -10 Max. 15 +15, -15 Max. V mA Note: Output noise voltage = Equivalent input noise voltage x Voltage gain *2: Recommended DC power supply (analog power supply): 15 V Current capacity: More than 1.5 times the maximum current consumption Ripple noise: 5 mVp-p or less *3: Preamp for P3257-30/-31 available upon request 2 Amplifiers for infrared detectors C4159/C5185 series, C3757-02 Dimensional outlines (unit: mm) C4159-01/-03/-04/-05/-06 OUT 11.5 30 PREAMPLIFIER POWER IN OUT 39.5 12.5 4-pin connector 60 HIGH MID LOW IN 39.5 24.5 25 PREAMPLIFIER POWER 60 37 12.5 11.5 4-pin connector C4159-02 BNC Gain adjusting screw Offset voltage adjusting screw BNC connector BNC connector Gain adjusting screw 14 14 25 26.2 23 85 15 23 35 85 Solder leads to these terminals. Note: Socket for lead attachment is not provided. KIRDA0046EB KIRDA0047EA C5185/-01 OUT Bias adjusting screw 38.5 12.5 25 37 IN OUT BNC 13.5 IN 4-pin connector PREAMPLIFIER POWER 60 HIGH MID LOW 39.5 11.5 PREAMPLIFIER POWER 30 60 24.5 4-pin connector C3757-02 BNC connector BNC connector 85 18 12 18 30 18 18 30 21.2 85 Solder leads to these terminals. Note: Socket for lead attachment is not provided. KIRDA0048EB KIRDA0049EB C4159-03, C5185 and C3757-02 conform to the European EMC directives (Applied standard: EN 61326 Class B). ! "#$$% & '' &((! ) '' * ++#,-+ - -. ) /01-%11% 2 3 4%+5 10-/0/-00++ 673 4%+5 10-/0/-1+%/ 3 ) 3 0,$ 6 8 &(9 7 ,:+$ 9 !2 $%%$;-$:+$ 3 4+5 :$%-#0+-$:,$ 673 4+5 :$%-#0+-+#+% < 3 & * <3 = +$ *-%##++ < 3 4/:5 $%+1#-0;1$ 673 4/:5 $%+1#-#,1% 6 3 & 6 8>3 +: 8 & :+%%# )7 6 3 00-4+5 ,: 10 ;+ $$ 673 00-4+5 ,: 10 ;+ +$ ' 3 & ' >3 # ) +$ 8 ? < ) >; +9? ' 3 4//5 +;$;-#:/%%% 673 4//5 +;$;-0#1;;; ! @ 3 & ! 93 A +# @-+;+ /+ 3 4/,5 %-1$:-$0+-$$ 673 4/,5 %-1$:-$0+-$+ 3 & 8>3 +B@ #$$#$ 4 5 3 40:5 $#-:01-%+-;00 673 40:5 $#-:01-%+-;/+ 3 Cat. No. KIRD1011E08 Apr. 2008 DN