!Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. P50E.pdf Sep.19,2012 CERAFILr (Filters/Traps/Discriminators) for Audio/Visual Equipment Cat.No.P50E-6 !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. EU RoHS Compliant s s s All the products in this catalog comply with EU RoHS. EU RoHS is "the European Directive 2011/65/EU on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment." For more details, please refer to our website 'Murata's Approach for EU RoHS' (http://www.murata.com/info/rohs.html). P50E.pdf Sep.19,2012 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. CONTENTS Sep.19,2012 1 CERAFILr and "CERAFIL" in this catalog are the trademarks of Murata Manufacturing Co., Ltd. Part Numbering 2 2 1. CERAFILr 3 1-1 CERAFILr 10.7MHz 1 Small Chip Type SFECF Series 5 2 Chip Type SFECV/SFECK Series 11 3 Standard Lead Type SFELF Series 14 4 Low Loss Type SFELF Series 17 5 Low Spurious Response Type SFELF Series 20 6 Wide Bandwidth Type SFELF Series 23 7 Narrow Bandwidth Type SFELF Series 25 8 For FM-IF Tuners SFELF Series 27 Related Data on Lead Type 30 7 9 4.5-6.5MHz Chip Type SFSKA Series 31 8 10 2.3-5.7MHz Chip Type SFSKB Series 34 4 5 6 1-2 CERAFILr 2.3-6.5MHz 1-3 CERAFILr 455kHz 9 11 Chip Type SFPKA Series 38 12 Lead Type SFPLA/CFWLA Series 40 13 For AM Stereo Wide Bandwidth Type SFPLA/CFWLA/CFULA Series 42 SFp Series Temperature Characteristics 44 11 2. Ceramic Trap 14 Ceramic Trap 4.5-6.5MHz Chip Type TPSKA Series 10 45 3. Ceramic Discriminator 12 15 10.7MHz Ultra Thin Chip Type CDSCB Series 47 Applied IC Reference Table 52 Notice 53 Packaging 69 Part Number Index 74 13 14 15 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 o Part Numbering CERAFILr for FM (Part Number) SF E LF q w e A A0 -B0 t y u i 10M7 F r yCenter Frequency/Tolerance qProduct ID Product ID SF Ceramic Filters wOscillation/Number of Elements Code Center Frequency Tolerance A Center Frequency mentioned by specification 30kHz B -30kHz shifted from center frequency of code "A" 30kHz C +30kHz shifted from center frequency of code "A" 30kHz Code Oscillation/Number of Elements D -60kHz shifted from center frequency of code "A" 30kHz E 2 Elements Thickness Expander mode E +60kHz shifted from center frequency of code "A" 30kHz T 3 Elements Thickness Expander mode H Center Frequency mentioned by specification 25kHz V 2 Elements Thickness Expander mode (2nd Harmonic) V -50kHz shifted from center frequency of code "H" 25kHz W +50kHz shifted from center frequency of code "H" 25kHz K 2 Elements Thickness Expander mode (3rd Overtone) K Center Frequency mentioned by specification 20kHz Z Combination of A, B, C, D, E -- M Combination of A, B, C -- F Nominal Center Frequency -- eStructure/Size Code Structure/Size Lp Lead Type Cp Chip Type p is "A" or subsequent code, which indicates the structure/size. rNominal Center Frequency Expressed by four-digit alphanumerics. The unit is in hertz (Hz). Decimal point is expressed by capital letter "M" in case of MHz. 3dB bandwidth of "F" signifies the frequency difference (both + and -) from reference frequency, which is nominal center frequency. uSeries Code Series A0 Two-digit alphanumerics express series iPackaging Code t3dB Bandwidth 2 Packaging -B0 Bulk Embossed Taping o180mm Code 3dB Bandwidth -R0 C 450kHz min -R1 Embossed Taping o330mm D 350kHz min -A0 1500pcs. /Radial Taping H0=18mm E 330kHz -A1 1000pcs. /Radial Taping H0=18mm F 280kHz G 230kHz H 180kHz J 150kHz K 110kHz L 80kHz M 50kHz N 35kHz Radial taping is applied to lead type and embossed taping to chip type. With non-standard products, two-digit alphanumerics indicating "Individual Specification" are added between "uSeries" and "iPackaging." P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 CERAFILr (Part Number) SF S KA 4M50 CF 00 -R1 q w e r t y u qProduct ID tProduct Specification Code (1) Product ID Product Specification Code (1) Code SF Ceramic Filters wOscillation/Numbers of Element Code Oscillation/Numbers of Element S 2 Elements Thickness Shear mode BF Tight Bandwidth Type CF Standard Bandwidth Type DF Broad Bandwidth Type EF Ultra-broad Bandwidth Type yProduct Specification Code (2) eStructure/Size Code Structure/Size Kp Chip Type p is "A" or subsequent code, which indicates the structure/size. Code Product Specification Code (2) 00 Standard Type uPackaging Packaging Code rNominal Center Frequency -B0 Bulk Expressed by four-digit alphanumerics. The unit is in hertz (Hz). Decimal point is expressed by capital letter "M" in case of MHz. -R1 Embossed Taping o=330mm With non-standard products, two-digit alphanumerics indicating "Individual Specification" is added between "yProduct Specification Code (2)" and "uPackaging." CERAFILr for AM (Part Number) SF P KA 455K D4A -B0 q w e r t y tProduct Specification qProduct ID Product ID SF Ceramic Filters CF Ceramic Filters Code Product Specification D4A Three-digit alphanumerics indicate product specification of 3dB or 6dB frequency tolerance. ppA indicates standard type. wOscillation/Numbers of Element Code Oscillation/Numbers of Element P 4 Elements Area Expansion mode eStructure/Size yPackaging Code Packaging -B0 Bulk -R0 Embossed Taping (o180mm) Code Structure/Size -R1 Embossed Taping (o330mm) Lp Lead Type -M0 Magazine Cassette Cp/Kp Chip Type p is "A" or subsequent code, which indicates the structure/size. It varies depending on vibration mode and number of elements. Radial taping is applied to lead type and embossed taping to chip type. With non-standard products, three-digit alphanumerics indicating "Individual Specification" is added between "tProduct Specification" and "yPackaging." rNominal Center Frequency Expressed by four-digit alphanumerics. The unit is in hertz (Hz). Capital letter "K" following three figures expresses the unit of "kHz." 3 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 Ceramic Traps (Part Number) TP S KA 4M00 q w e r B 00 -R0 t y u qProduct ID tProduct Specification Code (1) Product ID TP Code Product Specification (1) B Broad bandwidth Type C Low capacitance Type Ceramic Traps wFunction yProduct Specification Code (2) Code Function S Single Traps Code Product Specification (2) 00 Standard Type eStructure/Size Code Structure/Size Kp Chip Type uPackaging Packaging Code p is "A" or subsequent code, which indicates the structure/size. rNominal Center Frequency Expressed by four-digit alphanumerics. The unit is in hertz (Hz). Decimal point is expressed by capital letter "M" in case of MHz. -B0 Bulk -R1 Embossed Taping o=330mm With non-standard products, three-digit alphanumerics indicating "Individual Specification" is added between "yProduct Specification Code (2)" and "uPackaging." Discriminators for FM (Part Number) CD A LF 10M7 q w e r G A t y 001 -B0 u i yCenter Frequency/Tolerance qProduct ID Product ID CD Discriminators wOscillation Code Center Frequency Tolerance A Center Frequency mentioned by specification 30kHz B -30kHz shifted from center frequency of code "A" 30kHz C +30kHz shifted from center frequency of code "A" 30kHz Code Oscillation D -60kHz shifted from center frequency of code "A" 30kHz A Thickness Expander mode E +60kHz shifted from center frequency of code "A" 30kHz S Thickness Shear mode H Center Frequency mentioned by specification 25kHz V -50kHz shifted from center frequency of code "H" 25kHz W +50kHz shifted from center frequency of code "H" 25kHz eStructure/Size Code Structure/Size K Center Frequency mentioned by specification 20kHz Lp Lead Type Z Combination of A, B, C, D, E -- Cp Chip Type M Combination of A, B, C -- F Nominal Center Frequency -- p is "A" or subsequent code, which indicates the structure/size. 3dB bandwidth of "F" signifies the frequency difference (both + and -) from reference frequency, which is nominal center frequency. rNominal Center Frequency Expressed by four-digit alphanumerics. The unit is in hertz (Hz). Decimal point is expressed by capital letter "M" in case of MHz. tSeries Code Series G Two-digit alphanumerics express series uIC Code IC 001 Applicable IC Control Code iPackaging Code Packaging -B0 Bulk -A0 Radial Taping H0=18mm -R0 Embossed Taping o=180mm -R1 Embossed Taping o=330mm Radial taping is applied to lead type and embossed taping to chip type. With non-standard products, an alphanumerics indicating "Individual Specification" is added between "uIC" and "iPackaging." 4 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 CERAFILr (CERAFILr 10.7MHz) for Audio/Visual Equipment 1 Small Chip Type SFECF Series 1.30.1 SFECF10M7 series for FM receivers are small, high-performance and super thin (1.4mm max.) filters. The piezoelectric element is sandwiched by the ceramic substrate. They have 1.4mm max. thickness and a small mounting area (3.45x3.1mm). SFECF series and CDSCB series (MHz Discriminator) enable customers to make VICS/RKE/TPMS set very thin and small. 3.10.2 3.450.2 Input electrode marker 0 to 0.4 (0.6) (0.6) (0.6) 0 to 0.4 (1.28)(1.28) 0.3 min. 0.3 min. c Features 1. The filters are mountable by automatic placers. 2. They are slim, at only 1.4mm max. thickness, and have a small mounting area (3.45x3.1mm) enabling flexible PCB design. 3. Various bandwidths are available. Select a suitable type in accordance with the desired selectivity. 4. Operating Temperature Range: -20 to +80C (Standard Type) -40 to +85C (High-reliability Type) Storage Temperature Range: -40 to +85C (Standard Type) -55 to +85C (High-reliability Type) (1) (6) (2) (3) (5) (4) (1.28)(1.28) 0 to 0.35 0.750.3 0.850.3 0.850.3 0.650.3 0.70.3 0.650.3 (1): Input (2)(5): Ground (3)(4): No connection (6): Output : EIAJ Monthly Code ( ): Reference (in mm) 0 to 0.35 Standard Type Part Number Center Nominal Center Frequency Frequency (fn) (fo) (MHz) (MHz) 3dB Bandwidth (kHz) Attenuation (kHz) Insertion Loss (dB) Ripple (dB) Spurious Attenuation (1) (dB) Spurious Attenuation (2) (dB) Input/Output Impedance (ohm) SFECF10M7HA00-R0 10.700 30kHz - 180 40kHz 470 max. 4.02.0dB 1.0 max. 30 min. 30 min. [within 9MHz to fo] [within fo to 12MHz] 330 SFECF10M7HF00-R0 - 10.700 fn25 min. 510 max. 8.0max. [at fn] 1.0 max. 30 min. 25 min. [within 9MHz to fn] [within fn to 12MHz] 330 SFECF10M7GA00-R0 10.700 30kHz - 230 50kHz 510 max. 3.52.0dB 1.0 max. 30 min. 30 min. [within 9MHz to fo] [within fo to 12MHz] 330 SFECF10M7GF00-R0 - 10.700 fn45 min. 560 max. 8.0max. [at fn] 1.0 max. 30 min. 25 min. [within 9MHz to fn] [within fn to 12MHz] 330 SFECF10M7FA00-R0 10.700 30kHz - 280 50kHz 590 max. 3.02.0dB 1.0 max. 30 min. 30 min. [within 9MHz to fo] [within fo to 12MHz] 330 SFECF10M7FF00-R0 - 10.700 fn65 min. 620 max. 7.0max. [at fn] 1.0 max. 30 min. 25 min. [within 9MHz to fn] [within fn to 12MHz] 330 SFECF10M7EA00-R0 10.700 30kHz - 330 50kHz 700 max. 3.02.0dB 1.0 max. 30 min. 30 min. [within 9MHz to fo] [within fo to 12MHz] 330 SFECF10M7DA0001-R0 10.700 30kHz - 420 min. 950 max. 3.02.0dB 3.0 max. 35 min. 25 min. [within 9MHz to fo] [within fo to 12MHz] 330 - 10.700 fn150 min. 990 max. 6.0max. [at fn] 3.0 max. 20 min. 20 min. [within 9MHz to fn] [within fn to 12MHz] 330 SFECF10M7DF00-R0 Area of Attenuation: [within 20dB] Area of Insertion Loss: at minimum loss point Area of Ripple: within 3dB B.W. Center frequency (fo) defined by the center of 3dB bandwidth. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page. 5 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 High-Reliability Type 1 Center Nominal Center Frequency Frequency (fn) (fo) (MHz) (MHz) Part Number 3dB Bandwidth (kHz) Attenuation Insertion Loss (kHz) (dB) Spurious Attenuation (1) (dB) Ripple (dB) Spurious Attenuation (2) (dB) Input/Output Impedance (ohm) SFECF10M7HA00S0-R0 10.700 30kHz - 180 40kHz 470 max. 4.02.0dB 1.0 max. 30 min. 30 min. [within 9MHz to fo] [within fo to 12MHz] 330 SFECF10M7HF00S0-R0 - 10.700 fn25 min. 510 max. 8.0max. [at fn] 1.0 max. 30 min. 25 min. [within 9MHz to fn] [within fn to 12MHz] 330 SFECF10M7GA00S0-R0 10.700 30kHz - 230 50kHz 510 max. 3.52.0dB 1.0 max. 30 min. 30 min. [within 9MHz to fo] [within fo to 12MHz] 330 SFECF10M7GF00S0-R0 - 10.700 fn45 min. 560 max. 8.0max. [at fn] 1.0 max. 30 min. 25 min. [within 9MHz to fn] [within fn to 12MHz] 330 SFECF10M7FA00S0-R0 10.700 30kHz - 280 50kHz 590 max. 3.02.0dB 1.0 max. 30 min. 30 min. [within 9MHz to fo] [within fo to 12MHz] 330 SFECF10M7FF00S0-R0 - 10.700 fn65 min. 630 max. 7.0max. [at fn] 1.0 max. 30 min. 25 min. [within 9MHz to fn] [within fn to 12MHz] 330 SFECF10M7EA00S0-R0 10.700 30kHz - 330 50kHz 700 max. 3.02.0dB 1.0 max. 30 min. 30 min. [within 9MHz to fo] [within fo to 12MHz] 330 SFECF10M7DF00S0-R0 - 10.700 fn145 min. 990 max. 6.0max. [at fn] 3.0 max. 20 min. 20 min. [within 9MHz to fn] [within fn to 12MHz] 330 Area of Attenuation: [within 20dB] Area of Insertion Loss: at minimum loss point Area of Ripple: within 3dB B.W. Center frequency (fo) defined by the center of 3dB bandwidth. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page. c Standard Center Frequency Rank Code CODE 30kHz Step 25kHz Step D 10.64MHz30kHz 10.650MHz25kHz B 10.67MHz30kHz 10.675MHz25kHz A 10.70MHz30kHz 10.700MHz25kHz C 10.73MHz30kHz 10.725MHz25kHz E 10.76MHz30kHz 10.750MHz25kHz Z Combination A, B, C, D, E M Combination A, B, C c Test Circuit (5) (4) 1.05 (6) 0.1 0.3 0.1 c Standard Land Pattern Dimensions (3) (4) (2) (5) 1.40 0.3 R1 (1) 0.1 0.3 (3) 1.05 (2) 0.1 E1 (1) (6) Rg R2 C2 E2 RF Voltmeter S.S.G. 0.1 0.1 0.8 0.6 0.8 0.6 0.8 It indicates solder resist land pattern. 6 (1): Input (2)(5): Ground (3)(4): No connection (6): Output (in mm) Rg = 50 R1 = 280 5% R2 = 330 5% (1): Input C2 = 10 2 pF (Including stray capacitance and Input capacitance (2)(5): Ground of RF voltmeter) (3)(4): No connection E1: S.S.G. Output Voltage (6): Output P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 c Frequency Characteristics Standard Type 0 7.0 1 6.0 1 6.0 2 5.0 2 5.0 3 4.0 3 4.0 4 3.0 4 3.0 5 2.0 5 2.0 6 1.0 6 1.0 10.700 Frequency (MHz) 10.900 7 0.0 11.100 10.300 10.700 Frequency (MHz) 10.900 0.0 11.100 SFECF10M7EA00-R0 7.0 0 7.0 1 6.0 1 6.0 2 5.0 2 5.0 3 4.0 3 4.0 4 3.0 4 3.0 5 2.0 5 2.0 6 1.0 6 1.0 7 10.300 10.500 10.700 10.900 Attenuation (dB) 0 G.D.T. (sec.) Attenuation (dB) SFECF10M7FA00-R0/SFECF10M7FF00-R0 10.500 7 0.0 11.100 10.300 10.500 Frequency (MHz) SFECF10M7DA0001-R0 10.700 Frequency (MHz) 10.900 0.0 11.100 SFECF10M7DF00-R0 0 7.0 1 6.0 1 6.0 2 5.0 2 5.0 3 4.0 3 4.0 4 3.0 4 3.0 5 2.0 5 2.0 6 1.0 6 1.0 7 10.500 10.700 Frequency (MHz) 10.900 0.0 11.100 Attenuation (dB) 7.0 G.D.T. (sec.) 0 10.300 G.D.T. (sec.) 10.500 7 10.300 10.500 10.700 Frequency (MHz) 10.900 G.D.T. (sec.) 7 G.D.T. (sec.) 7.0 Attenuation (dB) 0 10.300 Attenuation (dB) 1 SFECF10M7GA00-R0/SFECF10M7GF00-R0 G.D.T. (sec.) Attenuation (dB) SFECF10M7HA00-R0/SFECF10M7HF00-R0 0.0 11.100 7 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. c Frequency Characteristics High-reliability Type 0 7.0 1 6.0 1 6.0 2 5.0 2 5.0 3 4.0 3 4.0 4 3.0 4 3.0 5 2.0 5 2.0 6 1.0 6 1.0 10.500 10.700 Frequency (MHz) 10.900 7 0.0 11.100 10.300 10.900 0.0 11.100 SFECF10M7EA00S0-R0 0 7.0 1 6.0 1 6.0 2 5.0 2 5.0 3 4.0 3 4.0 4 3.0 4 3.0 5 2.0 5 2.0 6 1.0 6 1.0 7 10.500 10.700 10.900 7 0.0 11.100 10.300 Frequency (MHz) 7.0 1 6.0 2 5.0 3 4.0 4 3.0 5 2.0 6 1.0 7 10.300 10.500 10.700 Frequency (MHz) 10.900 0.0 11.100 G.D.T. (sec.) SFECF10M7DF00S0-R0 0 Attenuation (dB) 7.0 10.300 8 10.700 Frequency (MHz) 0 G.D.T. (sec.) Attenuation (dB) SFECF10M7FA00S0-R0/SFECF10M7FF00S0-R0 10.500 10.500 10.700 Frequency (MHz) 10.900 0.0 11.100 G.D.T. (sec.) 7 10.300 Attenuation (dB) 7.0 G.D.T. (sec.) SFECF10M7GA00S0-R0/SFECF10M7GF00S0-R0 0 G.D.T. (sec.) Attenuation (dB) SFECF10M7HA00S0-R0/SFECF10M7HF00S0-R0 Attenuation (dB) 1 Sep.19,2012 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 c Frequency Characteristics (Spurious) Standard Type 0 0 10 10 20 20 30 40 30 40 50 50 60 60 70 8.700 9.700 10.700 Frequency (MHz) 11.700 70 8.700 12.700 10 10 20 20 30 40 60 60 11.700 11.700 12.700 40 50 10.700 10.700 Frequency (MHz) 30 50 9.700 9.700 SFECF10M7EA00-R0 0 Attenuation (dB) Attenuation (dB) SFECF10M7FA00-R0/SFECF10M7FF00-R0 0 70 8.700 1 SFECF10M7GA00-R0/SFECF10M7GF00-R0 Attenuation (dB) Attenuation (dB) SFECF10M7HA00-R0/SFECF10M7HF00-R0 12.700 Frequency (MHz) 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 SFECF10M7DA0001-R0/SFECF10M7DF00-R0 0 10 Attenuation (dB) 20 30 40 50 60 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 9 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. c Frequency Characteristics (Spurious) High-reliability Type SFECF10M7GA00S0-R0/SFECF10M7GF00S0-R0 0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFECF10M7HA00S0-R0/SFECF10M7HF00S0-R0 30 40 30 40 50 50 60 60 70 8.700 9.700 10.700 Frequency (MHz) 11.700 70 8.700 12.700 0 10 10 20 20 30 40 60 60 10.700 11.700 12.700 Frequency (MHz) SFECF10M7DF00S0-R0 0 10 20 30 40 50 60 70 8.700 10 9.700 10.700 Frequency (MHz) 11.700 12.700 11.700 12.700 40 50 9.700 10.700 Frequency (MHz) 30 50 70 8.700 9.700 SFECF10M7EA00S0-R0 0 Attenuation (dB) Attenuation (dB) SFECF10M7FA00S0-R0/SFECF10M7FF00S0-R0 Attenuation (dB) 1 Sep.19,2012 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 CERAFILr (CERAFILr 10.7MHz) for Audio/Visual Equipment Chip Type SFECV/SFECK Series 2 6.90.3 4.050.4 SFECV/SFECK10M7 series for FM receivers are monolithic type ceramic filters that utilize the thickness expander mode of piezoelectric ceramics. SFECV series enable customers to make an AM/FM set very thin, and it can be useful to the total chip circuit. 2.90.3 1.20.5 1.20.5 (2) (1) 1.50.2 1. The piezoelectric element is sandwiched by heat resistant substrate, thus it has excellent mechanical strength, and it is suitable for automatic mounting. 2. Various bandwidths are available. Select a suitable type in accordance with the desired selectivity. 3. Operating Temperature Range: -20 to +80C (Standard Type) -40 to +85C (High-reliability Type) Storage Temperature Range: -40 to +85C (Standard Type) -55 to +85C (High-reliability Type) 1.50.2 (3) c Features 1.20.3 : Marking 1.00.5 1.00.5 1.00.5 : EIAJ Monthly Code : Center Frequency Rank Code (1) : Input (2) : Ground (3) : Output (in mm) c Applications 1. Small, thin radios 2. Automotive radios 3. Headphone stereos Standard Type Spurious Attenuation (1) (dB) Spurious Attenuation (2) (dB) Input/Output Impedance (ohm) Part Number Center Frequency (fo) (MHz) 3dB Bandwidth (kHz) SFECV15M0EQ0001-R0 15.000 50kHz 300 min. 750 max. 7.0max. 1.0 max. 30 min. 30 min. [within 14MHz to fo] [within fo to 16MHz] 330 SFECV10M7KA00-R0 10.700 30kHz 110 30kHz 320 max. 6.02.0dB 1.0 max. 35 min. 35 min. [within 9MHz to fo] [within fo to 12MHz] 330 SFECV10M7JA00-R0 10.700 30kHz 150 40kHz 380 max. 5.52.0dB 1.0 max. 35 min. 35 min. [within 9MHz to fo] [within fo to 12MHz] 330 Attenuation Insertion Loss (kHz) (dB) Ripple (dB) Area of Attenuation: [within 20dB] Area of Insertion Loss: at minimum loss point Center frequency (fo) defined by the center of 3dB bandwidth. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page. High-Reliability Type Spurious Attenuation (1) (dB) Spurious Attenuation (2) (dB) Input/Output Impedance (ohm) Part Number Center Frequency (fo) (MHz) 3dB Bandwidth (kHz) SFECK10M7KA00S0-R0 10.700 30kHz 110 30kHz 320 max. 6.02.0dB 1.0 max. 35 min. 35 min. [within 9MHz to fo] [within fo to 12MHz] 330 SFECK10M7JA00S0-R0 10.700 30kHz 150 40kHz 380 max. 5.52.0dB 1.0 max. 35 min. 35 min. [within 9MHz to fo] [within fo to 12MHz] 330 Attenuation Insertion Loss (kHz) (dB) Ripple (dB) Area of Attenuation: [within 20dB] Area of Insertion Loss: at minimum loss point Center frequency (fo) defined by the center of 3dB bandwidth. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page. 11 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 c Standard Center Frequency Rank Code 2 CODE 30kHz Step 25kHz Step D 10.64MHz30kHz 10.650MHz25kHz B 10.67MHz30kHz 10.675MHz25kHz A 10.70MHz30kHz 10.700MHz25kHz C 10.73MHz30kHz 10.725MHz25kHz E 10.76MHz30kHz 10.750MHz25kHz Z Combination A, B, C, D, E M Combination A, B, C c Standard Land Pattern Dimensions 1.2 1.2 c Test Circuit 1.2 R1 (2) Rg 4.0 (3) (1) E1 R2 C2 E2 S.S.G. =-10dBm 1.65 1.65 2.85 2.85 Land Rg = 50 R1 = 280 5% R2 = 330 5% C2 = 10 2 pF (Including stray capacitance and Input capacitance of RF voltmeter) E1 : S.S.G. Output Voltage (in mm) RF Voltmeter (1) : Input (2) : Ground (3) : Output c Frequency Characteristics Standard Type 10.0 2 8.0 4 6.0 6 4.0 8 2.0 10 14.700 14.800 14.900 15.000 15.100 Frequency (MHz) 15.200 7.5 2 7.0 3 6.5 4 6.0 5 5.5 6 5.0 7 10.300 12 10.500 10.700 Frequency (MHz) 10.900 4.5 11.100 G.D.T. (sec.) Attenuation (dB) 1 1 6.5 2 6.0 3 5.5 4 5.0 5 4.5 6 4.0 10.300 SFECV10M7JA00-R0 8.0 7.0 7 0.0 15.300 0 0 10.500 10.700 Frequency (MHz) 10.900 3.5 11.100 G.D.T. (sec.) 0 Attenuation (dB) SFECV10M7KA00-R0 G.D.T. (sec.) Attenuation (dB) SFECV15M0EQ0001-R0 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 c Frequency Characteristics High-reliability Type SFECK10M7JA00S0-R0 8.0 1 6.5 1 7.5 2 6.0 2 7.0 3 5.5 3 6.5 4 5.0 4 6.0 5 4.5 5 5.5 6 4.0 6 5.0 7 10.300 10.500 10.700 Frequency (MHz) 10.900 3.5 11.100 7 10.300 10.500 10.700 Frequency (MHz) 10.900 2 G.D.T. (sec.) 0 Attenuation (dB) 7.0 G.D.T. (sec.) Attenuation (dB) SFECK10M7KA00S0-R0 0 4.5 11.100 c Frequency Characteristics (Spurious) Standard Type SFECV15M0EQ0001-R0 SFECV10M7KA00-R0 0 0 10 10 20 Attenuation (dB) Attenuation (dB) 20 30 40 50 30 40 50 60 60 70 80 13.000 14.000 15.000 Frequency (MHz) 16.000 70 8.700 17.000 9.700 10.700 Frequency (MHz) 11.700 12.700 11.700 12.700 SFECV10M7JA00-R0 0 10 Attenuation (dB) 20 30 40 50 60 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 c Frequency Characteristics (Spurious) High-reliability Type SFECK10M7JA00S0-R0 0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFECK10M7KA00S0-R0 30 40 30 40 50 50 60 60 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 70 8.700 9.700 10.700 Frequency (MHz) 13 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 CERAFILr (CERAFILr 10.7MHz) for Audio/Visual Equipment Standard Lead Type SFELF Series 7.02.0 EIAJ CODE 7.02.0 MARKING 5.01.0 1.380.2 1.70.1 0.50.1 c Features 3.01.0 (3) (1) : Input (2) : Ground (3) : Output (in mm) (1) (2) 7.02.0 EIAJ CODE 7.02.0 MARKING 1.380.2 1.70.1 5.01.0 1. These miniature filters have high mechanical strength. 2. Low loss, favorable waveform symmetry, and high selectivity 3. Various bandwidths are available for applications in wide to narrow bands. 4. Small dispersion and stable characteristics 5. Change in center frequency is typically within 30ppm/C at -20 to +80C. 6. High reliability 0.30.1 2.50.2 2.50.2 SFELF10M7HA00-B0 0.50.1 3.01.0 SFELF10M7GA00-B0 0.30.1 2.50.2 2.50.2 (3) (1) : Input (2) : Ground (3) : Output (in mm) (1) (2) 7.02.0 EIAJ CODE 7.02.0 MARKING 5.01.0 1.380.2 1.70.1 0.50.1 2.50.2 2.50.2 3.01.0 SFELF10M7FA00-B0 0.30.1 3 SFELF10M7 series for FM-receivers are monolithic type ceramic filters that use the thickness expander mode of the piezoelectric ceramic. As part of the environment protection program, the solder for terminal plating and terminal-element connection inside of the ceramic filter contain no lead (Pb). (3) (2) (1) : Input (2) : Ground (3) : Output (in mm) (1) Center Frequency (fo) (MHz) 3dB Bandwidth (kHz) Attenuation (kHz) Insertion Loss (dB) Spurious Attenuation (1) (dB) Spurious Attenuation (2) (dB) Input/Output Impedance (ohm) SFELF10M7HA00-B0 10.700 30kHz 180 40kHz 520 max. 7.0max. 40 min. [within 9MHz to fo] 40 min. [within fo to 12MHz] 330 SFELF10M7GA00-B0 10.700 30kHz 230 50kHz 570 max. 4.02.0dB 40 min. [within 9MHz to fo] 40 min. [within fo to 12MHz] 330 SFELF10M7FA00-B0 10.700 30kHz 280 50kHz 650 max. 4.02.0dB 30 min. [within 9MHz to fo] 30 min. [within fo to 12MHz] 330 Part Number Area of Attenuation: [within 20dB] Area of Insertion Loss: at minimum loss point Center frequency (fo) defined by the center of 3dB bandwidth. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page. 14 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 c Standard Center Frequency Rank Code CODE 30kHz Step 25kHz Step Color Code D 10.64MHz30kHz 10.650MHz25kHz Black B 10.67MHz30kHz 10.675MHz25kHz Blue A 10.70MHz30kHz 10.700MHz25kHz Red C 10.73MHz30kHz 10.725MHz25kHz Orange E 10.76MHz30kHz 10.750MHz25kHz White Z Combination A, B, C, D, E M Combination A, B, C 3 c Test Circuit (1) R1 (2) (3) RF Rg C R2 Voltmeter S.S.G Rg + R1 = R2 = Input and Output Impedance C = 10pF (Including stray capacitance and input capacitance of RF voltmeter.) (1) : Input (2) : Ground (3) : Output c Frequency Characteristics 6.5 0 6.0 1 6.0 1 5.5 2 5.5 2 5.0 3 5.0 3 4.5 4 4.5 4 4.0 5 4.0 5 3.5 6 3.5 6 3.0 7 10.500 10.600 10.700 Frequency (MHz) 10.800 Attenuation (dB) 0 7 3.0 10.900 10.500 10.600 10.700 Frequency (MHz) 10.800 G.D.T. (sec.) SFELF10M7GA00-B0 G.D.T. (sec.) Attenuation (dB) SFELF10M7HA00-B0 2.5 10.900 5.5 1 5.0 2 4.5 3 4.0 4 3.5 5 3.0 6 2.5 7 10.500 10.600 10.700 Frequency (MHz) 10.800 G.D.T. (sec.) Attenuation (dB) SFELF10M7FA00-B0 0 2.0 10.900 15 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 c Frequency Characteristics (Spurious) 3 SFELF10M7GA00-B0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFELF10M7HA00-B0 0 30 40 50 60 60 9.700 10.700 Frequency (MHz) 11.700 12.700 SFELF10M7FA00-B0 0 10 20 Attenuation (dB) 40 50 70 8.700 30 40 50 60 70 8.700 16 30 9.700 10.700 Frequency (MHz) 11.700 12.700 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 CERAFILr (CERAFILr 10.7MHz) for Audio/Visual Equipment Low Loss Type SFELF Series 7.02.0 SFELF10M7 series for FM receivers are monolithic type ceramic filters that use the thickness expander mode of the piezoelectric ceramic. As part of the environment protection program, the solder for terminal plating and terminal-element connection inside of the ceramic filter contain no lead (Pb). EIAJ CODE 7.02.0 MARKING 1.380.2 1.70.1 c Features 4 5.01.0 0.50.1 3.01.0 1. Insertion loss is 1 to 1.5dB lower than conventional products. These types are useful for elevating the sensitivity of sets. 2. Small dispersion and stable characteristics 3. Excellent shape factor of frequency response 4. Good waveform symmetry 0.30.1 2.50.2 2.50.2 SFELF10M7JAA0-B0 (3) (1) : Input (2) : Ground (3) : Output (in mm) (1) (2) 7.02.0 EIAJ CODE 7.02.0 MARKING 5.01.0 1.380.2 1.70.1 0.50.1 3.01.0 (3) MARKING MARKING 7.02.0 7.02.0 EIAJ CODE 0.50.1 (3) (2) (1) : Input (2) : Ground (3) : Output SFELF10M7FAA0-B0 0.30.1 2.50.2 2.50.2 3.01.0 0.30.1 2.50.2 2.50.2 SFELF10M7GAA0-B0 3.01.0 0.50.1 5.01.0 1.380.2 1.70.1 5.01.0 1.380.2 1.70.1 (in mm) (1) (2) 7.02.0 EIAJ CODE (1) : Input (2) : Ground (3) : Output 7.02.0 SFELF10M7HAA0-B0 0.30.1 2.50.2 2.50.2 (in mm) (1) (3) (2) (1) : Input (2) : Ground (3) : Output (in mm) (1) Center Frequency (fo) (MHz) 3dB Bandwidth (kHz) Attenuation (kHz) Insertion Loss (dB) Spurious Attenuation (1) (dB) Spurious Attenuation (2) (dB) Input/Output Impedance (ohm) SFELF10M7JAA0-B0 10.700 30kHz 150 40kHz 360 max. 4.52.0dB 35 min. [within 9MHz to fo] 35 min. [within fo to 12MHz] 330 SFELF10M7HAA0-B0 10.700 30kHz 180 40kHz 470 max. 3.51.5dB 35 min. [within 9MHz to fo] 35 min. [within fo to 12MHz] 330 SFELF10M7GAA0-B0 10.700 30kHz 230 50kHz 520 max. 3.02.0dB 35 min. [within 9MHz to fo] 35 min. [within fo to 12MHz] 330 SFELF10M7FAA0-B0 10.700 30kHz 280 50kHz 590 max. 2.52.0dB 30 min. [within 9MHz to fo] 30 min. [within fo to 12MHz] 330 Part Number Area of Attenuation: [within 20dB] Area of Insertion Loss: at minimum loss point Center frequency (fo) defined by the center of 3dB bandwidth. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page. 17 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 c Standard Center Frequency Rank Code CODE 30kHz Step 25kHz Step Color Code D 10.64MHz30kHz 10.650MHz25kHz Black B 10.67MHz30kHz 10.675MHz25kHz Blue A 10.70MHz30kHz 10.700MHz25kHz Red C 10.73MHz30kHz 10.725MHz25kHz Orange E 10.76MHz30kHz 10.750MHz25kHz White Z Combination A, B, C, D, E M Combination A, B, C c Test Circuit 4 (1) R1 (2) (3) RF Rg C R2 Voltmeter S.S.G Rg + R1 = R2 = Input and Output Impedance C = 10pF (Including stray capacitance and input capacitance of RF voltmeter.) (1) : Input (2) : Ground (3) : Output c Frequency Characteristics 7.0 0 6.5 1 6.5 1 6.0 2 6.0 2 5.5 3 5.5 3 5.0 4 5.0 4 4.5 5 4.5 5 4.0 6 4.0 6 3.5 10.600 10.700 Frequency (MHz) 10.800 7 3.5 10.900 10.500 10.800 3.0 10.900 SFELF10M7FAA0-B0 0 5.5 1 5.5 1 5.0 2 5.0 2 4.5 3 4.5 3 4.0 4 4.0 4 3.5 5 3.5 5 3.0 6 3.0 6 2.5 7 10.600 10.700 Frequency (MHz) 10.800 2.5 10.900 Attenuation (dB) 6.0 10.500 18 10.700 Frequency (MHz) 0 G.D.T. (sec.) Attenuation (dB) SFELF10M7GAA0-B0 10.600 7 10.500 10.600 10.700 Frequency (MHz) 10.800 2.0 10.900 G.D.T. (sec.) 7 10.500 Attenuation (dB) 0 G.D.T. (sec.) SFELF10M7HAA0-B0 G.D.T. (sec.) Attenuation (dB) SFELF10M7JAA0-B0 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 c Frequency Characteristics (Spurious) SFELF10M7HAA0-B0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFELF10M7JAA0-B0 0 30 40 30 40 50 50 60 60 70 8.700 9.700 10.700 Frequency (MHz) 11.700 70 8.700 12.700 0 10 10 20 20 30 40 60 60 10.700 Frequency (MHz) 11.700 4 12.700 40 50 9.700 11.700 30 50 70 8.700 10.700 Frequency (MHz) SFELF10M7FAA0-B0 0 Attenuation (dB) Attenuation (dB) SFELF10M7GAA0-B0 9.700 12.700 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 19 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 CERAFILr (CERAFILr 10.7MHz) for Audio/Visual Equipment Low Spurious Response Type SFELF Series 7.52.0 SFELF10M7 series for FM-receivers are monolithic type ceramic filters that use the thickness expander mode of the piezoelectric ceramic. As part of the environment protection program, the solder for terminal plating and terminal-element connection inside of the ceramic filter contain no lead (Pb). EIAJ CODE 5.01.0 1.380.2 1.70.1 0.50.1 3.01.0 (3) 7.52.0 MARKING MARKING 7.02.0 7.52.0 EIAJ CODE EIAJ CODE (1) (2) 3.01.0 SFELF10M7HAB0-B0 0.30.1 2.50.2 2.50.2 3.01.0 0.30.1 2.50.2 2.50.2 (3) (in mm) (1) (2) 7.52.0 7.52.0 MARKING MARKING EIAJ CODE 7.02.0 (3) 5.01.0 0.50.1 EIAJ CODE 0.50.1 SFELF10M7FAB0-B0 (3) (2) (1) 0.30.1 2.50.2 2.50.2 3.01.0 0.30.1 2.50.2 2.50.2 3.01.0 0.50.1 5.01.0 1.380.2 1.70.1 5.01.0 1.380.2 1.70.1 (in mm) 7.02.0 0.50.1 SFELF10M7GAB0-B0 (in mm) 1.380.2 1.70.1 5.01.0 1.380.2 1.70.1 SFELF10M7JAB0-B0 (1) (2) 7.02.0 SFELF10M7KAB0-B0 These types have lower spurious response compared to standard filters. 0.30.1 2.50.2 2.50.2 c Features 5 7.02.0 MARKING (3) (in mm) (2) (1) (in mm) Center Frequency (fo) (MHz) 3dB Bandwidth (kHz) Attenuation (kHz) Insertion Loss (dB) Spurious Attenuation (1) (dB) Spurious Attenuation (2) (dB) Input/Output Impedance (ohm) SFELF10M7KAB0-B0 10.700 30kHz 110 30kHz 350 max. 7.02.0dB 45/30 min. [within 9MHz to fo] 30 min. [within fo to 12MHz] 330 SFELF10M7JAB0-B0 10.700 30kHz 150 40kHz 380 max. 5.52.0dB 45 min. [within 9MHz to fo] 45 min. [within fo to 12MHz] 330 SFELF10M7HAB0-B0 10.700 30kHz 180 40kHz 520 max. 5.02.0dB 45 min. [within 9MHz to fo] 45 min. [within fo to 12MHz] 330 SFELF10M7GAB0-B0 10.700 30kHz 230 50kHz 570 max. 3.02.0dB 45 min. [within 9MHz to fo] 45 min. [within fo to 12MHz] 330 Part Number Continued on the following page. 20 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 Continued from the preceding page. Part Number Center Frequency (fo) (MHz) 3dB Bandwidth (kHz) Attenuation (kHz) Insertion Loss (dB) Spurious Attenuation (1) (dB) Spurious Attenuation (2) (dB) Input/Output Impedance (ohm) 10.700 30kHz 280 50kHz 650 max. 3.02.0dB 45 min. [within 9MHz to fo] 45 min. [within fo to 12MHz] 330 SFELF10M7FAB0-B0 Area of Attenuation: [within 20dB] Area of Insertion Loss: at minimum loss point Center frequency (fo) defined by the center of 3dB bandwidth. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page. c Standard Center Frequency Rank Code CODE 30kHz Step 25kHz Step Color Code D 10.64MHz30kHz 10.650MHz25kHz Black B 10.67MHz30kHz 10.675MHz25kHz Blue A 10.70MHz30kHz 10.700MHz25kHz Red C 10.73MHz30kHz 10.725MHz25kHz Orange E 10.76MHz30kHz 10.750MHz25kHz White Z Combination A, B, C, D, E M Combination A, B, C 5 c Test Circuit (1) R1 (2) (3) RF Rg C R2 Voltmeter S.S.G Rg + R1 = R2 = Input and Output Impedance C = 10pF (Including stray capacitance and input capacitance of RF voltmeter.) (1) : Input (2) : Ground (3) : Output c Frequency Characteristics 7.0 1 7.5 1 6.5 2 7.0 2 6.0 3 6.5 3 5.5 4 6.0 4 5.0 5 5.5 5 4.5 6 5.0 6 4.0 10.600 10.700 Frequency (MHz) 10.800 4.5 10.900 7 10.500 10.700 Frequency (MHz) 10.800 3.5 10.900 SFELF10M7GAB0-B0 6.5 0 6.0 1 6.0 1 5.5 2 5.5 2 5.0 3 5.0 3 4.5 4 4.5 4 4.0 5 4.0 5 3.5 6 3.5 6 3.0 7 10.500 10.600 10.700 Frequency (MHz) 10.800 3.0 10.900 Attenuation (dB) 0 G.D.T. (sec.) Attenuation (dB) SFELF10M7HAB0-B0 10.600 7 10.500 10.600 10.700 Frequency (MHz) 10.800 G.D.T. (sec.) 7 10.500 Attenuation (dB) 0 G.D.T. (sec.) SFELF10M7JAB0-B0 8.0 G.D.T. (sec.) Attenuation (dB) SFELF10M7KAB0-B0 0 2.5 10.900 Continued on the following page. 21 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 Continued from the preceding page. c Frequency Characteristics 5.5 1 5.0 2 4.5 3 4.0 4 3.5 5 3.0 6 2.5 7 10.500 10.700 Frequency (MHz) 10.800 2.0 10.900 c Frequency Characteristics (Spurious) SFELF10M7JAB0-B0 0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFELF10M7KAB0-B0 30 40 30 40 50 50 60 60 70 8.700 9.700 10.700 Frequency (MHz) 11.700 70 12.700 0 0 10 10 20 20 30 40 60 60 10.700 Frequency (MHz) 11.700 12.700 SFELF10M7FAB0-B0 0 10 20 30 40 50 60 70 8.700 22 9.700 10.700 Frequency (MHz) 11.700 10.700 Frequency (MHz) 11.700 12.700 40 50 9.700 9.700 30 50 70 8.700 8.700 SFELF10M7GAB0-B0 Attenuation (dB) Attenuation (dB) SFELF10M7HAB0-B0 Attenuation (dB) 5 10.600 G.D.T. (sec.) Attenuation (dB) SFELF10M7FAB0-B0 0 12.700 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 CERAFILr (CERAFILr 10.7MHz) for Audio/Visual Equipment Wide Bandwidth Type SFELF Series 7.02.0 SFELF10M7 series for FM-receivers are monolithic type ceramic filters that use the thickness expander mode of the piezoelectric ceramic. As part of the environment protection program, the solder for terminal plating and terminal-element connection inside of the ceramic filter contain no lead (Pb). EIAJ CODE 7.02.0 MARKING 5.01.0 1.380.2 1.70.1 0.50.1 c Features 3.01.0 Realizes wider band characteristics not obtained by conventional ceramic filters. 0.30.1 2.50.2 2.50.2 SFELF10M7EA00-B0 (3) (1) : Input (2) : Ground (3) : Output (in mm) (1) (2) 7.02.0 6 EIAJ CODE 7.02.0 MARKING 5.01.0 1.380.2 1.70.1 0.50.1 3.01.0 SFELF10M7DF00-B0 0.30.1 2.50.2 2.50.2 (3) Center Nominal Center 3dB Attenuation Insertion Loss Frequency Frequency (fn) Bandwidth (kHz) (dB) (fo) (MHz) (MHz) (kHz) Part Number Spurious Attenuation (1) (dB) (2) (1) : Input (2) : Ground (3) : Output (in mm) (1) Spurious Attenuation (2) (dB) Input/Output Impedance (ohm) SFELF10M7EA00-B0 10.700 30kHz - 330 50kHz 680 max. 4.02.0dB 30 min. 30 min. [within 9MHz to fo] [within fo to 12MHz] 330 SFELF10M7DF00-B0 - 10.700 fn175 min. 950 max. 3.02.0dB 20 min. 20 min. [within 5MHz to fn] [within fn to 15MHz] 470 Area of Attenuation: [within 20dB] Area of Insertion Loss: at minimum loss point Center frequency (fo) defined by the center of 3dB bandwidth. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page. c Standard Center Frequency Rank Code (SFELF10M7EA00-B0) CODE 30kHz Step 25kHz Step Color Code D 10.64MHz30kHz 10.650MHz25kHz Black B 10.67MHz30kHz 10.675MHz25kHz Blue A 10.70MHz30kHz 10.700MHz25kHz Red C 10.73MHz30kHz 10.725MHz25kHz Orange E 10.76MHz30kHz 10.750MHz25kHz White Z Combination A, B, C, D, E M Combination A, B, C 23 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 c Test Circuit (1) R1 (2) (3) RF Rg C R2 Voltmeter S.S.G Rg + R1 = R2 = Input and Output Impedance C = 10pF (Including stray capacitance and input capacitance of RF voltmeter.) (1) : Input (2) : Ground (3) : Output c Frequency Characteristics 4.5 1 4.0 1 4.0 2 3.5 2 3.5 3 3.0 3 3.0 4 2.5 4 2.5 5 2.0 5 2.0 6 1.5 6 1.5 7 10.300 10.500 10.700 Frequency (MHz) 10.900 Attenuation (dB) 0 G.D.T. (sec.) Attenuation (dB) 6 SFELF10M7DF00-B0 4.5 7 1.0 11.100 10.300 10.500 10.700 Frequency (MHz) 10.900 1.0 11.100 c Frequency Characteristics (Spurious) 0 0 10 10 20 20 30 40 30 40 50 50 60 60 70 8.700 24 SFELF10M7DF00-B0 Attenuation (dB) Attenuation (dB) SFELF10M7EA00-B0 9.700 10.700 Frequency (MHz) 11.700 12.700 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 G.D.T. (sec.) SFELF10M7EA00-B0 0 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 CERAFILr (CERAFILr 10.7MHz) for Audio/Visual Equipment Narrow Bandwidth Type SFELF Series 7.02.0 c Features EIAJ CODE 7.02.0 MARKING SFELF10M7LFTA/KAH0 series realizes narrower band characteristics not obtained by conventional ceramic filters. Besides, low spurious and temperature characteristics are stable. This series is suitable for European car-audio or AM upconversion use that needs stable narrow band characteristics. As part of the environment protection program, the solder for terminal plating and terminal-element connection inside of the ceramic filter contain no lead (Pb). 5.01.0 1.380.2 1.70.1 0.50.1 3.01.0 0.30.1 2.50.2 2.50.2 SFELF10M7LFTA-B0 (3) (1) : Input (2) : Ground (3) : Output (in mm) (1) (2) 7.02.0 EIAJ CODE 7.02.0 MARKING 7 5.01.0 1.380.2 1.70.1 0.50.1 3.01.0 SFELF10M7KAH0-B0 0.30.1 2.50.2 2.50.2 (3) Center Nominal Center 3dB Attenuation Insertion Loss Frequency Frequency (fn) Bandwidth (kHz) (dB) (fo) (MHz) (MHz) (kHz) Part Number Spurious Attenuation (1) (dB) (2) (1) : Input (2) : Ground (3) : Output (in mm) (1) Spurious Attenuation (2) (dB) Input/Output Impedance (ohm) SFELF10M7LFTA-B0 - 10.700 fn25 min. 280 max. 7.02.0dB 30 min. 30 min. [within 9MHz to fn] [within fn to 12MHz] 330 SFELF10M7KAH0-B0 10.700 30kHz - 110 30kHz 350 max. 7.02.0dB 30 min. 30 min. [within 9MHz to fo] [within fo to 12MHz] 330 Area of Attenuation: [within 20dB] Area of Insertion Loss: at minimum loss point Center frequency (fo) defined by the center of 3dB bandwidth. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page. c Standard Center Frequency Rank Code (SFELF10M7KAH0-B0) CODE 30kHz Step 25kHz Step Color Code D 10.64MHz30kHz 10.650MHz25kHz Black B 10.67MHz30kHz 10.675MHz25kHz Blue A 10.70MHz30kHz 10.700MHz25kHz Red C 10.73MHz30kHz 10.725MHz25kHz Orange E 10.76MHz30kHz 10.750MHz25kHz White Z Combination A, B, C, D, E M Combination A, B, C 25 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 c Test Circuit (1) R1 (2) (3) RF Rg Voltmeter C R2 S.S.G Rg + R1 = R2 = Input and Output Impedance C = 10pF (Including stray capacitance and input capacitance of RF voltmeter.) (1) : Input (2) : Ground (3) : Output c Frequency Characteristics 7 8.0 1 11.0 1 7.5 2 10.0 2 7.0 3 9.0 3 6.5 4 8.0 4 6.0 5 7.0 5 5.5 6 6.0 6 5.0 7 10.600 10.650 10.700 Frequency (MHz) 10.750 5.0 10.800 Attenuation (dB) 0 7 10.600 10.650 10.700 Frequency (MHz) 10.750 4.5 10.800 c Frequency Characteristics (Spurious) 0 0 10 10 20 20 30 40 30 40 50 50 60 60 70 8.700 26 SFELF10M7KAH0-B0 Attenuation (dB) Attenuation (dB) SFELF10M7LFTA-B0 9.700 10.700 Frequency (MHz) 11.700 12.700 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 G.D.T. (sec.) SFELF10M7KAH0-B0 12.0 G.D.T. (sec.) Attenuation (dB) SFELF10M7LFTA-B0 0 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 CERAFILr (CERAFILr 10.7MHz) for Audio/Visual Equipment For FM-IF Tuners SFELF Series 7.02.0 SFELF10M7 series for FM-receivers are monolithic type ceramic filters that use the thickness expander mode of the piezoelectric ceramic. As part of the environment protection program, the solder for terminal plating and terminal-element connection inside of the ceramic filter contain no lead (Pb). EIAJ CODE 7.02.0 MARKING 5.01.0 1.380.2 1.70.1 0.50.1 c Features 3.01.0 1. Little dispersion of amplitude characteristics and phase characteristics (G. D. T. characteristics) 2. The SFELF_G series is based on SFELF_FA00/GA00/ HA00, and it obtains high selectivity with low loss. There is little dispersion of amplitude and GDT characteristics, and low distortion rate can be obtained. 3. The flatness of GDT is inspected for all products. 0.30.1 2.50.2 2.50.2 SFELF10M7HA0G-B0 (3) (1) : Input (2) : Ground (3) : Output (in mm) (1) (2) 7.02.0 EIAJ CODE 7.02.0 MARKING 5.01.0 1.380.2 1.70.1 0.50.1 3.01.0 SFELF10M7GA0G-B0 0.30.1 2.50.2 2.50.2 (3) (1) : Input (2) : Ground (3) : Output (in mm) (1) (2) 7.02.0 EIAJ CODE 7.02.0 MARKING 5.01.0 1.380.2 1.70.1 0.50.1 3.01.0 0.30.1 2.50.2 2.50.2 SFELF10M7FA0G-B0 (3) Part Number Center 3dB Attenuation Insertion Loss Frequency Bandwidth (kHz) (dB) (fo) (MHz) (kHz) Spurious Attenuation (1) (dB) Spurious Attenuation (2) (dB) (2) (1) : Input (2) : Ground (3) : Output (in mm) (1) GDT Bandwidth Input/Output Impedance (kHz) (ohm) SFELF10M7HA0G-B0 10.700 30kHz 180 40kHz 520 max. 7.0max. 40 min. 40 min. [within 9MHz to fo] [within fo to 12MHz] fo45min. 330 SFELF10M7GA0G-B0 10.700 30kHz 230 50kHz 600 max. 7.0max. 40 min. 40 min. [within 9MHz to fo] [within fo to 12MHz] fo60min. 330 SFELF10M7FA0G-B0 10.700 30kHz 280 50kHz 650 max. 4.02.0dB 30 min. 30 min. [within 9MHz to fo] [within fo to 12MHz] fo85min. 330 Area of Attenuation: [within 20dB] Area of Insertion Loss: at minimum loss point Center frequency (fo) defined by the center of 3dB bandwidth. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page. 27 8 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 c Standard Center Frequency Rank Code CODE 30kHz Step 25kHz Step Color Code D 10.64MHz30kHz 10.650MHz25kHz Black B 10.67MHz30kHz 10.675MHz25kHz Blue A 10.70MHz30kHz 10.700MHz25kHz Red C 10.73MHz30kHz 10.725MHz25kHz Orange E 10.76MHz30kHz 10.750MHz25kHz White Z Combination A, B, C, D, E M Combination A, B, C c Test Circuit R1 (1) (2) (3) RF Rg R2 C Voltmeter S.S.G Rg + R1 = R2 = Input and Output Impedance C = 10pF (Including stray capacitance and input capacitance of RF voltmeter.) (1) : Input (2) : Ground (3) : Output c Frequency Characteristics 6.5 0 6.0 1 6.0 1 5.5 2 5.5 2 5.0 3 5.0 3 4.5 4 4.5 4 4.0 5 4.0 5 3.5 6 3.5 6 3.0 7 10.400 10.500 10.600 10.700 10.800 Frequency (MHz) 10.900 7 3.0 11.000 10.400 5.5 1 5.0 2 4.5 3 4.0 4 3.5 5 3.0 6 2.5 7 10.400 28 10.500 10.600 10.700 10.800 Frequency (MHz) 10.900 2.0 11.000 G.D.T. (sec.) Attenuation (dB) SFELF10M7FA0G-B0 0 Attenuation (dB) 0 G.D.T. (sec.) Attenuation (dB) 8 SFELF10M7GA0G-B0 10.500 10.600 10.700 10.800 Frequency (MHz) 10.900 2.5 11.000 G.D.T. (sec.) SFELF10M7HA0G-B0 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 c Frequency Characteristics (Spurious) SFELF10M7GA0G-B0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFELF10M7HA0G-B0 0 30 40 30 40 50 50 60 60 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 SFELF10M7FA0G-B0 0 10 Attenuation (dB) 20 30 40 50 60 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 8 29 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 CERAFILr 10.7MHz Related Data on Lead Type c Temperature Characteristics 0 -20 +2 +1 -20 0 +20 +40 Temperature (C) +60 +80 Insertion loss Variation (dB) -40 0 -1 -2 Variation (kHz) Variation (kHz) +20 SFELF10M7HA00-B0 Center frequency +40 +20 -20 0 +20 +40 Temperature (C) +60 3dB Bandwidth 0 -20 -40 -20 0 +20 +40 Temperature (C) +60 +40 +20 +80 Center frequency 0 -20 -40 +2 +1 -20 0 +20 +40 Temperature (C) +60 +80 0 +20 +40 Temperature (C) +60 +80 0 +20 +40 Temperature (C) +60 +80 Insertion loss 0 -1 -2 +80 Variation (kHz) Variation (dB) Variation (kHz) SFELF10M7GA00-B0 +40 +40 +20 -20 3dB Bandwidth 0 -20 -40 -20 c Matching Conditions 1. When using ceramic filters, it is most important to match the input/output load to impedance 330 ohm (SFELF10M7DF00-B0 is 470 ohm). Waveform symmetry is damaged when reactance is added to the input/output load. 2. Two ceramic filters directly connected can be used for high selectivity. For reducing waveform variation, it is recommended to input a buffer AMP between ceramic filters. 3. The SFELF10M7 series are of input/output symmetric structure so that in theory there is no input/output directionality. Actual circuits may use different input/output loading conditions (for example, mismatched impedance) or capacitance load. In such cases, the waveform will be a little changed by the direction of the input/output of the ceramic filters. c Loaded Resistance and Waveform (Rg+R1=330 ohm) Attenuation (dB) R2=560 0 1 2 3 4 5 6 7 1.2 1.0 0.8 0.6 0.4 0.2 0 10.5 10.6 10.7 10.8 10.9 Frequency (MHz) 1.2 1.0 0.8 0.6 0.4 0.2 0 10.5 10.6 10.7 10.8 10.9 Frequency (MHz) R2=1k 0 1 2 3 4 5 6 7 1.2 1.0 0.8 0.6 0.4 0.2 0 10.5 10.6 10.7 10.8 10.9 Frequency (MHz) Group Delay Time (sec.) Attenuation (dB) 0 1 2 3 4 5 6 7 Group Delay Time (sec.) 10.5 10.6 10.7 10.8 10.9 Frequency (MHz) R2=330 Attenuation (dB) 1.2 1.0 0.8 0.6 0.4 0.2 0 Group Delay Time (sec.) Attenuation (dB) 0 1 2 3 4 5 6 7 Group Delay Time (sec.) SFELF10M7GA00-B0 R2=220 c Loaded Capacitance and Waveform (Rg+R1=R2=330 ohm) Attenuation (dB) C=56pF 30 0 1 2 3 4 5 6 7 1.2 1.0 0.8 0.6 0.4 0.2 0 10.5 10.6 10.7 10.8 10.9 Frequency (MHz) 1.2 1.0 0.8 0.6 0.4 0.2 0 10.5 10.6 10.7 10.8 10.9 Frequency (MHz) C=82pF 0 1 2 3 4 5 6 7 1.2 1.0 0.8 0.6 0.4 0.2 0 10.5 10.6 10.7 10.8 10.9 Frequency (MHz) Group Delay Time (sec.) Attenuation (dB) 0 1 2 3 4 5 6 7 Group Delay Time (sec.) 10.5 10.6 10.7 10.8 10.9 Frequency (MHz) C=33pF Attenuation (dB) 1.2 1.0 0.8 0.6 0.4 0.2 0 Group Delay Time (sec.) Attenuation (dB) 0 1 2 3 4 5 6 7 Group Delay Time (sec.) SFELF10M7HA00-B0 C=10pF P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 CERAFILr (CERAFILr 2.3-6.5MHz) for Audio/Visual Equipment 4.5-6.5MHz Chip Type SFSKA Series SMD ceramic filter SFSKA_CF is a small and thin SMD filter sealed with a metal cap. Recommended for LCD-TVs, and small and thin tuners. 7.90.2 3.00.1 1.80.2 c Features 0.50.1 8.50.2 1. High attenuation outside bandwidth 2. Small and thin package 3. Reflow-solderable 0.60.2 3.80.2 1.00.1 1.30.2 0.30.1 1.30.2 (1) (2) (3) (1) : Input (2) : Ground (3) : Output (in mm) 2.50.2 2.50.2 Nominal Center Frequency (fn) (MHz) 3dB Bandwidth (kHz) 20dB Bandwidth (kHz) Insertion Loss (dB) Spurious Attenuation(1) (dB) Spurious Attenuation(2) (dB) Input/Output Impedance (ohm) SFSKA4M50CF00-R3 4.500 fn60 min. 600 max. 6.0 max. 20 min. [within 0 to fn] 15 min. [within fn to 7.0MHz] 1000 SFSKA5M50CF00-R3 5.500 fn60 min. 600 max. 6.0 max. 25 min. [within 0 to fn] 15 min. [within fn to 7.0MHz] 600 SFSKA6M00CF00-R3 6.000 fn60 min. 600 max. 6.0 max. 25 min. [within 0 to fn] 15 min. [within fn to 7.5MHz] 470 SFSKA6M50CF00-R3 6.500 fn60 min. 600 max. 6.0 max. 25 min. [within 0 to fn] 15 min. [within fn to 8.5MHz] 470 Part Number Area of Insertion Loss: at minimum loss point For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page. c Standard Land Pattern Dimensions 9 c Test Circuit SFSKA4M50CF00-R3 1.0 1.5 (1) (2) (3) 1.0 1.5 R1 Rg 4.8 1.0 E1 R2 C2 E2 RF Voltmeter S.S.G. (in mm) R1+Rg=R2=1000 5%, Rg=50 C2=10pF (Including stray capacitance and Input capacitance of RF Voltmeter) E1:S.S.G. Output voltage (1) : Input (2) : Ground (3) : Output Continued on the following page. 31 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 Continued from the preceding page. c Test Circuit SFSKA5M50CF00-R3 SFSKA6M00CF00-R3 (1) (2) (3) (1) (2) (3) R1 R1 Rg Rg E1 R2 C2 RF Voltmeter E2 S.S.G. E1 R2 C2 RF Voltmeter E2 S.S.G. R1+Rg=R2=600 5%, Rg=50 C2=10pF (Including stray capacitance and Input capacitance of RF Voltmeter) E1: S.S.G. Output voltage (1) : Input (2) : Ground (3) : Output R1+Rg=R2=470 5%, Rg=50 C2=10pF (Including stray capacitance and Input capacitance of RF Voltmeter) E1: S.S.G. Output voltage (1) : Input (2) : Ground (3) : Output SFSKA6M50CF00-R3 (1) (2) (3) R1 Rg E1 R2 C2 RF Voltmeter E2 S.S.G. R1+Rg=R2=470 5%, Rg=50 C2=10pF (Including stray capacitance and Input capacitance of RF Voltmeter) E1: S.S.G. Output voltage (1) : Input (2) : Ground (3) : Output c Frequency Characteristics SFSKA4M50CF00-R3 SFSKA5M50CF00-R3 0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) 9 30 40 50 60 30 40 50 60 70 70 3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 4.5 5.5 4.7 4.9 5.1 5.5 5.7 5.9 6.1 6.3 6.5 6.9 7.1 7.3 7.5 SFSKA6M50CF00-R3 0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFSKA6M00CF00-R3 30 40 50 60 30 40 50 60 70 70 5.0 5.2 5.4 5.6 5.8 6.0 6.2 Frequency (MHz) 32 5.3 Frequency (MHz) Frequency (MHz) 6.4 6.6 6.8 7.0 5.5 5.7 5.9 6.1 6.3 6.5 6.7 Frequency (MHz) P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 c Frequency Characteristics (Spurious) SFSKA5M50CF00-R3 0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFSKA4M50CF00-R3 30 40 50 40 50 60 60 70 30 70 0.0 2.0 4.0 6.0 8.0 10.0 0 2.0 SFSKA6M00CF00-R3 6.0 8.0 10.0 8.0 10.0 SFSKA6M50CF00-R3 0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) 4.0 Frequency (MHz) Frequency (MHz) 30 40 50 60 30 40 50 60 70 70 0 2.0 4.0 6.0 Frequency (MHz) 8.0 10.0 0 2.0 4.0 6.0 Frequency (MHz) 9 33 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 CERAFILr (CERAFILr 2.3-6.5MHz) for Audio/Visual Equipment 2.3-5.7MHz Chip Type SFSKB Series 5.20.1 (4) (1) 3.80.1 (3.5) The SFSKB series are SMD ceramic filters suitable for IR headphone applications. Center frequencies of 2.3, 2.8, 3.2, 3.8, 4.3, 4.8, 5.2, 5.7MHz are available. Realized small, thin and lightweight package, compared with conventional LC filters. It helps to compose multi-channel circuit on one PCB. No frequency adjustment is required on PCB and it contributes to the reduction of production cost. (2) (3) 1.350.15 (4.93) 4-0.35 c Features (4) (1) 0.250.1 (0.1) 1.00.1 (1.6) (3) (2) 0.30.1 4-0.35 (0.1) 1.50.1 (2.0) Terminal Connection (1) : Input (2) : Output (3) : Ground (4) : Terminal for external capacitor : EIAJ Monthly Code Tolerance unless otherwise specified : 0.1mm ( ) : Reference (in mm) 1. SMD package in plastic emboss tape, available for automatic placing. 2. They are slim, at only 1.5mm max. thickness, and have a small mounting area (5.2x3.8mm) enabling flexible PCB design. 3. Available for lead (Pb) free reflow soldering process. 4. Operating temperature range: 0 to +70C Storage temperature range: -55 to +85C 5. No frequency adjustment is required in production process. 6. Small, thin and lightweight package compared with conventional LC filters c Applications 1. IR headphone 2. Set Top Box for satellite broadcasting 10 Part Number Nominal Center Frequency (fn) (MHz) 3dB Bandwidth (kHz) 20dB Bandwidth (kHz) Insertion Loss (dB) Spurious Attenuation(1) (dB) Spurious Attenuation(2) (dB) Input/Output Impedance (ohm) SFSKB2M30GF00-R1 2.300 fn75 min. 650 max. 6.0 max. 25 min. [within 1.3 to 1.8MHz] 23 min. [within 2.8 to 3.3MHz] 1000 SFSKB2M80GF00-R1 2.800 fn75 min. 650 max. 6.0 max. 25 min. [within 1.8 to 2.3MHz] 25 min. [within 3.3 to 3.8MHz] 1000 SFSKB3M20FF00-R1 3.200 fn75 min. 650 max. 6.0 max. 30 min. [within 2.2 to 2.8MHz] 30 min. [within 3.8 to 4.2MHz] 1000 SFSKB3M80GF00-R1 3.800 fn75 min. 650 max. 6.0 max. 30 min. [within 2.8 to 3.2MHz] 30 min. [within 4.3 to 4.8MHz] 1000 SFSKB4M30GF00-R1 4.300 fn75 min. 650 max. 6.0 max. 30 min. [within 3.3 to 3.8MHz] 30 min. [within 4.8 to 5.3MHz] 1000 SFSKB4M80GF00-R1 4.800 fn75 min. 650 max. 6.0 max. 30 min. [within 3.8 to 4.3MHz] 30 min. [within 5.2 to 5.8MHz] 1000 SFSKB5M20GF00-R1 5.200 fn75 min. 650 max. 6.0 max. 30 min. [within 4.2 to 4.8MHz] 30 min. [within 5.7 to 6.2MHz] 1000 SFSKB5M70GF00-R1 5.700 fn75 min. 650 max. 6.0 max. 30 min. [within 4.7 to 5.2MHz] 30 min. [within 6.2 to 6.7MHz] 1000 For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page. 34 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 c Standard Land Pattern Dimensions 2.0 1.8 1.3 1.6 1.3 1.8 (in mm) c Test Circuit (1) : Input (2) : Output (3) : Ground (4) : Terminal for external capacitor R1+Rg=R2=1.0k Cc=39pF5% C2=10pF (Including stray capacitance and Input capacitance of RF Voltmeter) E1 : S.S.G. Output Voltage R1+Rg=R2=1.0k Cc=33pF5% C2=10pF (Including stray capacitance and Input capacitance of RF Voltmeter) E1 : S.S.G. Output Voltage E2 C2 (1) : Input (2) : Output (3) : Ground (4) : Terminal for external capacitor (1) : Input (2) : Output (3) : Ground (4) : Terminal for external capacitor (3) S.S.G. R1+Rg=R2=1.0k Cc=15pF5% C2=10pF (Including stray capacitance and Input capacitance of RF Voltmeter) E1 : S.S.G. Output Voltage E2 (2) C2 (4) R2 Rg S.S.G. RF Voltmeter (1) E1 E1 E2 (3) C2 (2) RF Voltmeter SFSKB4M80GF00-R1 R1 R2 (4) Cc Rg (1) (3) S.S.G. SFSKB4M30GF00-R1/SFSKB5M70GF00-R1 R1 (2) Cc R1+Rg=R2=1.0k Cc=22pF5% C2=10pF (Including stray capacitance and Input capacitance of RF Voltmeter) E1 : S.S.G. Output Voltage (4) E1 E1 S.S.G. RF Voltmeter (1) Cc Rg (3) E2 (2) R1 C2 (4) R2 (1) Cc Rg R1 SFSKB2M80GF00-R1/SFSKB3M20FF00-R1 R2 SFSKB2M30GF00-R1/SFSKB3MZ0GF00-R1 RF Voltmeter 10 (1) : Input (2) : Output (3) : Ground (4) : Terminal for external capacitor (3) S.S.G. R1+Rg=R2=1.0k Cc=27pF5% C2=10pF (Including stray capacitance and Input capacitance of RF Voltmeter) E1 : S.S.G. Output Voltage E2 (2) C2 (4) R2 (1) E1 Rg R1 Cc SFSKB5M20GF00-R1 RF Voltmeter (1) : Input (2) : Output (3) : Ground (4) : Terminal for external capacitor 35 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 c Frequency Characteristics SFSKB2M80GF00-R1 0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFSKB2M30GF00-R1 30 40 50 60 70 1.300 30 40 50 60 1.800 2.300 2.800 70 1.800 3.300 2.300 Frequency (MHz) 0 0 10 10 20 20 30 40 50 60 2.700 3.200 3.700 70 2.800 4.200 3.300 5.800 6.200 6.700 SFSKB4M80GF00-R1 0 0 10 20 20 Attenuation (dB) Attenuation (dB) 3.800 Frequency (MHz) 30 40 50 30 40 50 60 3.800 4.300 4.800 70 3.800 5.300 4.300 Frequency (MHz) 4.800 Frequency (MHz) SFSKB5M20GF00-R1 SFSKB5M70GF00-R1 0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) 5.300 60 60 30 40 50 60 30 40 50 60 4.700 5.200 Frequency (MHz) 36 4.800 50 10 70 4.200 4.300 40 SFSKB4M30GF00-R1 70 3.300 3.800 30 Frequency (MHz) 10 3.300 SFSKB3M80GF00-R1 Attenuation (dB) Attenuation (dB) SFSKB3M20FF00-R1 70 2.200 2.800 Frequency (MHz) 5.700 6.200 70 4.700 5.200 5.700 Frequency (MHz) P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 c Frequency Characteristics (Spurious) SFSKB2M80GF00-R1 0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFSKB2M30GF00-R1 30 40 50 60 70 30 40 50 60 0.300 1.300 2.300 3.300 70 4.300 0.800 1.800 Frequency (MHz) 0 0 10 10 20 20 30 40 50 60 1.200 2.200 3.200 4.200 70 5.200 1.800 2.800 3.800 Frequency (MHz) SFSKB4M80GF00-R1 0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) 5.800 50 60 30 40 50 60 30 10 40 50 60 2.300 3.300 4.300 5.300 70 6.300 2.800 3.800 Frequency (MHz) 4.800 5.800 6.800 6.700 7.700 Frequency (MHz) SFSKB5M20GF00-R1 SFSKB5M70GF00-R1 0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) 4.800 40 SFSKB4M30GF00-R1 30 40 50 60 70 4.800 30 Frequency (MHz) 70 3.800 SFSKB3M80GF00-R1 Attenuation (dB) Attenuation (dB) SFSKB3M20FF00-R1 70 2.800 Frequency (MHz) 30 40 50 60 3.200 4.200 5.200 Frequency (MHz) 6.200 7.200 70 3.700 4.700 5.700 Frequency (MHz) 37 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 CERAFILr (CERAFILr 455kHz) for Audio/Visual Equipment Chip Type SFPKA Series 7.50.3 SFPKA series for AM use is one of the most recommendable intermediate filters, having such distinctive features as high selectivity, high stability and adjustment-free operation. Additionally, its easy matching with IC helps create an easy circuit design. 8.4 max. 7.00.3 3.00.3 MARKING EIAJ CODE 5.0 max. 0.90.1 2.00.3 1.50.3 2.00.3 c Features 1.50.3 1.60.3 Connection (1): Input (2): Ground (3): Output (1) (2) (3) 1. The filters are mountable by automatic placers and can be reflow soldered and withstand washing. 2. The filters are wide bandwidth and high selectivity, so they are suitable for car radio and multi-band radio. (in mm) Center Frequency (fo) (kHz) 6dB Bandwidth (kHz) Selectivity (-) (dB) Selectivity (+) (dB) Insertion Loss (dB) Input/Output Impedance (ohm) Element SFPKA450KH1A-R1 450.0 1.0kHz fn3.0 min. 40 min.[fn-9kHz] 40 min.[fn+9kHz] 6.0 max. 2000 4 SFPKA450KG1A-R1 450.0 1.0kHz fn4.5 min. 40 min.[fn-10kHz] 40 min.[fn+10kHz] 6.0 max. 1500 4 Part Number Area of Insertion Loss: at minimum loss point Center frequency (fo) is defined by the center of 6dB bandwidth. (fn) means nominal center frequency (450kHz). For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page. c Standard Land Pattern Dimensions c Recommended IFT Type SFPKA Winding Specification S(3) 1.6 2.475 0.8 Item 6.95 2.0 (1)--(2) (2)--(3) (4)--(6) 60T 125T 28T (4)S (2) 7.45 (1) (Bottom view) 1.1 0.925 2.0 2.0 0.9 1.55 11 c Test Circuit (3) (1) (2) Rg RF Voltmeter E1 R2 E2 S.S.G. 0dBm Rg+R1=R2=Input/Output Impedance E1: S.S.G. Output Voltage 38 No load Qu 40 Tuning Capacitance 180pF s -ATCHING OF #%2!&),r 3&0+! SERIES WITH )&4 IS DECIDED BY THE 1U OF )&4 AND )&4 SECONDARY SIDE IMPEDANCE \:\ 3ET THE 1U AT ABOUT BECAUSE A 1U VALUE WHICH IS TOO HIGH EG MAY PRODUCE RIPPLE IN THE WAVEFORM )T IS RECOMMENDED TO MATCH THE IMPEDANCE OF \:\ WITH THAT OF THE #%2!&),r (in mm) R1 (6) (1): Input (2): Ground (3): Output P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 c Frequency Characteristics 0 400 10 360 10 360 20 320 20 320 30 280 30 280 40 240 40 240 50 200 50 200 60 160 60 160 70 120 70 120 80 80 80 80 90 40 90 40 0 100 100 425 450 Frequency (kHz) 475 Attenuation (dB) 400 425 450 475 G.D.T. (sec.) SFPKA450KG1A-R1 G.D.T. (sec.) Attenuation (dB) SFPKA450KH1A-R1 0 0 Frequency (kHz) 11 39 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 CERAFILr (CERAFILr 455kHz) for Audio/Visual Equipment Lead Type SFPLA/CFWLA Series MARKING 7.30.3 EIAJ CODE 2.70.3 0.60.1 1.20.5 (1) Connection (1) : Input (2) : Ground (3) : Output 4.20.3 (2) SFPLA Series 0.80.1 3.00.3 1.5 max. 0.150.05 0.30.1 SFPLA/CFWLA series for AM use is one of the most suitable intermediate filters, having such distinctive features as high selectivity, high stability, high attenuation, and adjustment-free operation. Additionally, its easy matching with IC helps create an easy circuit design. This is the most suitable for car stereo and all band radio with high attenuation. 7.00.3 8.00.3 (3) (in mm) 3.30.5 0.80.1 3.50.5 0.15 2.90.3 2.60.3 2.90.3 2.9--0.3 (4) (3) (2) (1) (5) 2.30.5 4.30.3 1.350.5 1.20.5 CFWLA Series 1.5 max. 7.50.5 EIAJ CODE 7.00.5 11.00.5 MARKING 0.60.1 Connection (1): Input (2)(3)(4): Ground (5): Output (in mm) 2.00.3 Center Frequency (fo) (kHz) 6dB Bandwidth (kHz) Selectivity (-) (dB) Selectivity (+) (dB) Insertion Loss (dB) Input/Output Impedance (ohm) Element SFPLA450KJ1A-B0 450.0 1.0kHz fn2.0 min. 40 min.[fn-7.5kHz] 40 min.[fn+7.5kHz] 6.0 max. 2000 4 SFPLA450KH1A-B0 450.0 1.0kHz fn3.0 min. 40 min.[fn-9kHz] 40 min.[fn+9kHz] 6.0 max. 2000 4 CFWLA450KJFA-B0 450.0 (fn) fn2.0 min. 50 min.[fn-7.5kHz] 50 min.[fn+7.5kHz] 7.0 max. 2000 6 CFWLA450KHFA-B0 450.0 (fn) fn3.0 min. 50 min.[fn-9kHz] 50 min.[fn+9kHz] 6.0 max. 2000 6 Part Number Area of Insertion Loss: at minimum loss point Center frequency (fo) is defined by the center of 6dB bandwidth. (fn) means nominal center frequency (450kHz). For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page. 12 c Recommended IFT c Test Circuit SFPLA/CFWLA Type Item 7x7mm IFT Winding Specification S(3) (1)--(2) (2)--(3) (4)--(6) 60T 125T 28T R1 (4)S Input Output Rg (2) (1) (6) (Bottom view) No load Qu 40 Tuning Capacitance 180pF s -ATCHING OF #%2!&),r 3&0,!#&7,! SERIES WITH )&4 IS DECIDED BY THE 1U OF )&4 AND )&4 SECONDARY SIDE IMPEDANCE \:\ 3ET THE 1U AT ABOUT BECAUSE A 1U VALUE WHICH IS TOO HIGH EG MAY PRODUCE RIPPLE IN THE WAVEFORM )T IS RECOMMENDED TO MATCH THE IMPEDANCE OF \:\ WITH THAT OF THE #%2!&),r 40 RF R2 SSG Voltmeter Ground Rg+R1 =R2 : Input/Output Impedance P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 c Frequency Characteristics IFT+CFWLA450KHFA-B0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) IFT+SFPLA450KH1A-B0 0 30 40 30 40 50 50 60 60 70 430 440 450 460 470 70 430 440 450 Frequency (kHz) Frequency (kHz) 460 470 c Frequency Characteristics (Spurious) IFT+CFWLA450KHFA-B0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) IFT+SFPLA450KH1A-B0 0 30 40 50 30 40 50 60 60 70 70 80 0 1 2 3 4 5 6 Frequency (MHz) 7 8 9 10 80 0 1 2 3 4 5 6 Frequency (MHz) 7 8 9 10 12 41 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 CERAFILr (CERAFILr 455kHz) for Audio/Visual Equipment For AM Stereo Wide Bandwidth Type SFPLA/CFWLA/CFULA Series 2.70.3 (2) SFPLA Series (1) (3) 3.00.3 0.150.05 0.80.1 0.60.1 1.20.5 Connection (1) : Input (2) : Ground (3) : Output 4.20.3 1.5 max. 7.30.3 EIAJ CODE (in mm) 8.00.3 MARKING 7.00.5 11.00.5 MARKING 2.30.5 13 (4) (3) (2) (1) (5) 4.30.3 CFWLA Series 1.350.5 1.20.5 2.70.3 Connection (1): Input (2)(3)(4): Ground (5): Output (2) (3) (in mm) 2.00.3 1.20.5 0.60.1 Connection (1): Input (2): Ground (3): Output 3.30.5 Part Number Center Frequency (fo) (kHz) 6dB Bandwidth (kHz) Selectivity (-) (dB) Selectivity (+) (dB) Insertion Loss (dB) SFPLA450KG1A-B0 450.0 1.0kHz fn4.5 min. 30 min.[fn-9kHz] 30 min.[fn+9kHz] 6.0 max. SFPLA450KF1A-B0 450.0 1.0kHz fn6.0 min. SFPLA450KE1A-B0 450.0 1.0kHz fn7.5 min. 40 min.[fn-12.5kHz] 40 min.[fn+12.5kHz] 40 min.[fn-15kHz] (1) CFULA Series 3.00.3 7.30.3 0.60.1 0.80.1 4.20.3 0.150.05 2.60.3 2.90.3 2.9--0.3 1.5 max. 3.50.5 0.15 2.90.3 0.80.1 1.5 max. 7.50.5 EIAJ CODE 7.00.3 3.30.5 EIAJ CODE 40 min.[fn+15kHz] 0.30.1 MARKING 0.30.1 SFPLA/CFULA/CFWLA series for AM use is one of the most suitable intermediate filters, having such distinctive features as high selectivity, high stability, high attenuation, and adjustment-free operation. Additionally, its easy matching with IC helps create an easy circuit design. Especially, CFULA/CFWLA_Y series improves the frequency fidelity in the high sound area of an AM stereo with its wide band and flat characteristics of group delay time. 7.00.3 8.00.3 (in mm) GDT 20sec. Input/Output Bandwidth Impedance Element (kHz) (ohm) - 2000 4 6.0 max. - 2000 4 6.0 max. - 1500 4 SFPLA450KD1A-B0 450.0 1.0kHz fn10.0 min. 40 min.[fn-20kHz] 40 min.[fn+20kHz] 4.0 max. - 1500 4 CFULA450KG1Y-B0 450.0 1.0kHz fn4.5 min. 40 min.[fn-15kHz] 40 min.[fn+15kHz] 10.0 max. fn3 2000 4 CFULA450KF1Y-B0 450.0 1.0kHz fn6.0 min. CFULA450KD1Y-B0 450.0 1.0kHz fn10.0 min. CFWLA450KG1Y-B0 450.0 1.0kHz fn4.5 min. CFWLA450KF1Y-B0 450.0 1.0kHz fn6.0 min. CFWLA450KD1Y-B0 450.0 1.0kHz fn10.0 min. 40 min.[fn-17.5kHz] 40 min.[fn+17.5kHz] 9.0 max. fn4 2000 4 40 min.[fn-25kHz] 40 min.[fn+25kHz] 7.0 max. fn7 1500 4 50 min.[fn-15kHz] 50 min.[fn+15kHz] 11.0 max. fn4 2000 6 50 min.[fn-17.5kHz] 50 min.[fn+17.5kHz] 10.0 max. fn5 2000 6 50 min.[fn-25kHz] 50 min.[fn+25kHz] 8.0 max. fn8 1500 6 50 min.[fn-10kHz] 50 min.[fn+10kHz] 6.0 max. - 2000 6 6.0 max. - 2000 6 CFWLA450KGFA-B0 450.0 (fn) fn4.5 min. CFWLA450KFFA-B0 450.0 (fn) fn6.0 min. CFWLA450KEFA-B0 450.0 (fn) fn7.5 min. 50 min.[fn-15kHz] 50 min.[fn+15kHz] 6.0 max. - 1500 6 CFWLA450KDFA-B0 450.0 (fn) fn10.0 min. 50 min.[fn-20kHz] 50 min.[fn+20kHz] 4.0 max. - 1500 6 50 min.[fn-12.5kHz] 50 min.[fn+12.5kHz] Area of Insertion Loss: at minimum loss point Center frequency (fo) is defined by the center of 6dB bandwidth. (fn) means nominal center frequency (450kHz). For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page. 42 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. c Recommended IFT Sep.19,2012 c Test Circuit SFPLA/CFULA/CFWLA Type Item 7x7mm IFT Winding Specification S(3) (1)--(2) (2)--(3) (4)--(6) 60T 125T 28T Input R1 (4)S Output Rg (2) (1) (6) RF R2 SSG (Bottom view) No load Qu 40 Tuning Capacitance 180pF Voltmeter Ground s -ATCHING OF #%2!&),r 3&0,!#&5,!#&7,! SERIES WITH )&4 IS DECIDED BY THE 1U OF )&4 AND )&4 SECONDARY SIDE IMPEDANCE \:\ 3ET THE 1U AT ABOUT BECAUSE A 1U VALUE WHICH IS TOO HIGH EG MAY PRODUCE RIPPLE IN THE WAVEFORM )T IS RECOMMENDED TO MATCH THE IMPEDANCE OF \:\ WITH THAT OF THE #%2!&),r Rg+R1 =R2 : Input/Output Impedance c Frequency Characteristics IFT+CFWLA450KFFA-B0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) IFT+SFPLA450KF1A-B0 0 30 40 50 30 40 50 60 60 70 440 450 460 70 430 470 440 Frequency (kHz) 460 470 IFT+CFWLA450KF1Y-B0 10 10 20 200 30 100 40 0 50 60 Attenuation (dB) 0 Group Delay Time (sec.) Attenuation (dB) IFT+CFULA450KF1Y-B0 0 70 430 450 Frequency (kHz) 20 200 30 100 40 0 50 Group Delay Time (sec.) 430 60 440 450 Frequency (kHz) 460 470 70 430 440 450 460 470 Frequency (kHz) 13 43 !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. CERAFILr 455kHz SFp Series Temperature Characteristics 3dB Bandwidth (kHz) Insertion Loss (dB) Center Frequency (kHz) c SFPLA450KH1A-B0 44 +1 Temperature (C) -20 0 20 40 0 20 40 60 80 0 -1 +1 0 60 80 Temperature (C) -20 -1 +1 Temperature (C) 20 0 -20 -1 0 40 60 80 P50E.pdf Sep.19,2012 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 CERAFILr (Ceramic Trap) for Audio/Visual Equipment 4.5-6.5MHz Chip Type TPSKA Series SMD ceramic trap TPSKA_B is a small and thin SMD trap sealed with a metal cap recommended for LCD-TVs, and small and thin tuners. 7.90.2 3.00.1 1.80.2 c Features 0.50.1 8.50.2 1. High attenuation and high performance group delay time 2. Small and thin package 3. Reflow-solderable 0.60.2 3.80.2 1.00.1 1.30.2 0.30.1 1.30.2 (1) (2) (3) (1) : Input (2) : Ground (3) : Output (in mm) 2.50.2 2.50.2 Nominal Center Frequency (fn1) (MHz) Attenuation (at fn1) (dB) 30dB Attenuation BW (fn1) (kHz) TPSKA4M50B00-R3 4.500 35 min. 50 min. TPSKA5M50B00-R3 5.500 35 min. 70 min. TPSKA6M00B00-R3 6.000 35 min. 70 min. TPSKA6M50B00-R3 6.500 35 min. 70 min. Part Number For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page. c Standard Land Pattern Dimensions c Test Circuit L 1.0 1.0 1.5 1.0 R1 1.5 Rg 4.8 50 R2 RF Voltmeter S.S.G. Rg=50 R1=330 R2=1.0k L=15H (in mm) c Frequency Characteristics TPSKA5M50B00-R3 0 0 10 10 Attenuation (dB) Attenuation (dB) TPSKA4M50B00-R3 20 30 40 20 40 50 50 60 60 70 14 30 70 4.0 4.1 4.2 4.3 4.4 4.5 4.6 Frequency (MHz) 4.7 4.8 4.9 5.0 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 Frequency (MHz) Continued on the following page. 45 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 Continued from the preceding page. c Frequency Characteristics TPSKA6M50B00-R3 0 0 10 10 Attenuation (dB) Attenuation (dB) TPSKA6M00B00-R3 20 30 40 20 30 40 50 50 60 60 70 70 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.0 6.1 6.2 6.3 Frequency (MHz) 6.4 6.5 6.6 6.7 6.8 6.9 7.0 Frequency (MHz) c Frequency Characteristics (Spurious) 700 0 1000 600 10 800 20 500 20 600 30 400 30 400 40 300 40 200 50 200 50 0 60 100 60 70 0 70 Attenuation (dB) 0 10 80 80 1.0 2.0 3.0 Frequency (MHz) 4.0 5.0 0 1.0 2.0 7.0 8.0 9.0 10.0 1000 0 1000 800 10 800 20 600 20 600 30 400 30 400 40 200 40 200 50 0 50 0 Attenuation (dB) 0 10 60 60 70 70 80 80 0 46 4.0 5.0 6.0 Frequency (MHz) TPSKA6M50B00-R3 G.D.T. (nsec.) Attenuation (dB) TPSKA6M00B00-R3 3.0 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 10.0 0 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 10.0 G.D.T. (nsec.) 0 14 G.D.T. (nsec.) TPSKA5M50B00-R3 G.D.T. (nsec) Attenuation (dB) TPSKA4M50B00-R3 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 CERAFILr (Ceramic Discriminator) for Audio/Visual Equipment 0.30.2 10.7MHz Ultra Thin Chip Type CDSCB Series 0.20.2 1.4 max. 4.50.1 2.00.1 CDSCB10M7 series forms a resonator on a piezoelectric ceramic substrate. In combination with ICs, this type obtains stable demodulation characteristics in a wide bandwidth. They have 1.0mm max. thickness and small mounting area (4.5x2.0mm). 0.40.05 1.0 max. 4.1 max. 0.4(ref.) 0.4(ref.) 0.80.1 0.80.1 c Features 1. Compact and high reliability and recommended for automotive applications. 2. Can be combined with various ICs. The IC is determined by the last number in the part number. 3. Stable demodulation characteristics can be obtained without adjustment. 4. Stable temperature characteristics. 5. Available lead (Pb) free solder reflow. 1.50.1 1.50.1 (in mm) Center Frequency (fo) (MHz) Recovered Audio 3dB BW (kHz) Recovered Audio Output (mV) Distortion (%) S Curve (mV) IC CDSCB10M7GA105A-R0 10.700 30kHz 220 min. 110 min. 1.5 max. - TEA5757HL CDSCB10M7GA113-R0 10.700 30kHz 300 min. 110 min. 1.0 max. - TA2154FN CDSCB10M7GA119-R0 10.700 30kHz 500 min. 75 min. 1.0 max. - TRF6901 CDSCB10M7GA121-R0 10.700 30kHz 390 min. 80 min. 1.0 max. - LV23100V CDSCB10M7GA135-R0 10.700 30kHz 155 min. 75 min. - - TH71101 CDSCB10M7GA136-R0 10.700 30kHz 140 min. 120 min. - - TH7122 CDSCB10M7GF072-R0 10.700 (fn) fn150 min. 130 min. 2.0 max. - TA31161 CDSCB10M7GF107S-R0 10.700 (fn) fn80 min. 52 min. 3.0 max. - TA31272FN CDSCB10M7GF109-R0 10.700 (fn) fn100 min. 170 min. 3.0 max. - TK14588V CDSCB10M7GF123-R0 10.700 (fn) - - - 900 min. TA31275FN CDSCB10M7GF123S-R0 10.700 (fn) - - - 900 min. TA31275FN CDSCB10M7GF126-R0 10.700 (fn) - - - 400 min. NJM2295AV Part Number (fn) means nominal center frequency (10.700MHz). For safety purposes, avoid applying a direct current between the terminals. The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page. c Standard Center Frequency Rank Code CODE 30kHz Step 25kHz Step D 10.64MHz30kHz 10.650MHz25kHz B 10.67MHz30kHz 10.675MHz25kHz A 10.70MHz30kHz 10.700MHz25kHz C 10.73MHz30kHz 10.725MHz25kHz E 10.76MHz30kHz 10.750MHz25kHz Z Combination A, B, C, D, E M Combination A, B, C 15 47 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 c Standard Land Pattern Dimensions 2.6 3.0 1.0 2.0 1.0 (in mm) c Test Circuit CDSCB10M7GA105A-R0 CDSCB10M7GA113-R0 Vcc (1.2V) 35 3 34 4 33 5 32 6 100k 28 0.01 27 26 25 24 23 22 21 20 19 18 17 16 11 12 13 14 15 TA2154FN (TOSHIBA) 1 2 3 4 5 6 7 8 9 10 + X 30 8 29 9 28 10 27 11 26 12 DC OUT 29 31 TEA5757HL (PHILIPS) 7 30 S.S.G. 2.2 680p 2 0.01 + 100 0.01 10 + 48 47 46 45 44 43 42 41 40 39 38 37 0.1 1 36 0.01 0.1 0.01 Vcc (3.0V) D.C. OUT AF OUT X: CDSCB10M7GA113-R0 Unit C: F R: S.S.G. 10 25 0.47 0.1 + X AFC (n) 0.22 150 AF OUT X: CDSCB10M7GA105A-R0 Unit C: F R: CDSCB10M7GA119-R0 CDSCB10M7GA121-R0 Vcc (3.0V) 10p 10p 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 LV23100V (SANYO) 35 3 34 32 5 6 TRF6901 31 7 (TEXAS INSTRUMENTS) 30 8 29 9 28 100p 10 27 11 26 12 25 13 14 15 16 17 18 19 20 21 22 23 24 0.01 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 10k 10 1000p 33 4 2 + 0.047 + 47p + 0.47 0.01 3.3k 0.1 + 1 0.22 0.47 + S.G. 100p 10k + PIC16F84 (Control IC) PIC16F84 2 3 4 5 1k 2.2 6 7 1 8 2 3 4 5 6 7 8 9 9 10k + 10k 18 17 16 15 14 13 12 11 10 18 17 16 15 14 13 12 11 10 1 100p 2 1 X X 48 47 46 45 44 43 42 41 40 39 38 37 36 1 1 10k 0.01 82p 10 0.015 22+ 0.047 4.7 Vcc (3.2V) 0.01 220k 15p 0.047 120p 75 0.01 D.C. Output AF Output 68p 0.01 0.01 AF Output IF Input 100 4.7 AFC (p) 330p 0.1 13 14 15 16 17 18 19 20 21 22 23 24 0.1 X: CDSCB10M7GA119-R0 Unit C : F R: L: H 1k X: CDSCB10M7GA121-R0 2.2 + 10k 0.1 Unit C: F R: Continued on the following page. 15 48 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 Continued from the preceding page. c Test Circuit CDSCB10M7GA135-R0 CDSCB10M7GA136-R0 Vcc (5.0V) Vcc (5.0V) AF-OUT FKS-OUT 330p 0.1 0.1 24 23 22 21 20 19 18 17 25 16 26 100p 1000p 0.01 0.01 330k 15 27 14 TH7122 [Internal AFC Enabled] (MELEXIS) 28 220k 29 12 30 0.01 24 23 22 21 20 19 18 15 27 14 10 32 16 26 11 31 17 25 2 3 0.01 4 5 6 7 8 0.1 29 0.01 330p 13 100k 0.033 12 S.G. 1000p 30 330p AF-OUT 1000p TH71101, TH71102, TH71111 or TH71112 (MELEXIS) FKS-OUT 330p 0.01 28 0.01 9 1 12p C.D. 330p 13 C.D. 11 3.3k 0.01 31 10 330p 0.01 32 9 1 2 3 4 5 6 7 100k 8 18 0.01 17 16 1 2 3 13 4 5 6 12 11 7 1k X: CDSCB10M7GA135-R0 330p 100p 14 10 PIC16F84 (Control IC) S.G. + 10 15 8 9 10k X: CDSCB10M7GA136-R0 + 2.2 Unit C: F R: CDSCB10M7GF072-R0 Unit C: F R: 0.1 CDSCB10M7GF109-R0 Vcc (3V) 0.01 1.2 Vcc (3V) 4.7 R X X 0.01 D.C. OUT 10p 13 12 11 10 8p 12k 9 51k 5 6 0.01 7 8 16 X: CDSCB10M7GF072-R0 R: 820 Unit C: F R: L: H + 33 0.01 14 13 12 11 10 9 7 8 TK14588V (TOKO) 1 2 3 4 5 51 IF IN 15 0.01 4 0.01 3 0.01 2 0.01 1 0.01 14 TA31161 (TOSHIBA) 6 + S.S.G. 4.7 15 0.01 16 AF OUT 0.01 1000p X: CDSCB10M7GF109-R0 R: 820 Unit C: F R: L: H CDSCB10M7GF123-R0 CDSCB10M7GF126-R0 Vcc (5.0V) 22 1 2 3 21 20 19 0.01 0.01 18 17 16 20 15 14 13 8 9 10 11 12 16 15 14 1 2 3 4 5 6 7 0.01 0.1 7 17 1.8k 6 0.01 5 18 13 12 8 9 11 NJM2295AV (JRC) TA31275FN (TOSHIBA) 4 19 + 10 23 0.01 1000p 3300p 24 DC-OUT + DC-OUT 0.01 10 0.01 AF OUT 100p Vcc (5.0V) 10 8p S.S.G. X: CDSCB10M7GF123-R0 Unit C: F R: 180 10+ 0.01 10+ 0.1 0.01 0.1 C.D. 0.1 AF OUT R 0.01 X: CDSCB10M7GF126-R0 S.G. Unit C: F R: 15 49 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 c Recovered Audio Curve CDSCB10M7GA105A-R0 1000 CDSCB10M7GA113-R0 100 1000 10 100 100 AF Output 1 1 10 Distortion 10 1 1 0.1 T.H.D. (%) 10 T.H.D. (%) AF Output Voltage (mV) Distortion AF Output Voltage (mV) AF Output 100 0.1 Input = 100dB fdev. = 75kHz fmod. = 1kHz Vcc = 3.0V 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 10.3 10.4 10.5 Frequency (MHz) 10.6 CDSCB10M7GA119-R0 1000 10.8 10.9 11.0 11.1 CDSCB10M7GA121-R0 100 1000 10 100 100 AF Output 1 1 T.H.D. (%) Distortion 10 AF Output Voltage (mV) AF Output 100 AF Output Voltage (mV) 10.7 Frequency (MHz) 10 Distortion 10 1 1 0.1 0.1 Input = 100dB fdev. = 75kHz fmod. = 1kHz Vcc = 3.2V Input = 100dB fdev. = 60kHz fmod. = 1kHz Vcc = 3.0V 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 10.3 11.1 10.4 CDSCB10M7GA135-R0 10.6 10.7 10.8 10.9 11.0 11.1 CDSCB10M7GA136-R0 1000 1000 100 100 AF Output Voltage (mV) AF Output Voltage (mV) 10.5 Frequency (MHz) Frequency (MHz) 10 1 10 1 Input = 100dB fdev. = 50kHz fmod. = 1kHz Vcc = 5.0V 15 0.1 10.4 T.H.D. (%) 10.3 Input = 100dB fdev. = 75kHz fmod. = 1kHz Vcc = 1.2V 10.5 10.6 10.7 10.8 Frequency (MHz) 10.9 11.0 0.1 10.4 Input = 100dB fdev. = 50kHz fmod. = 1kHz Vcc = 5.0V 10.5 10.6 10.7 10.8 10.9 11.0 Frequency (MHz) Continued on the following page. 50 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 Continued from the preceding page. c Recovered Audio Curve CDSCB10M7GF072-R0 CDSCB10M7GF109-R0 100 10 100 10 10 1 10 1 1 0.1 0.1 1 Input = 100dB fdev. = 80kHz fmod. = 1kHz Vcc = 3.0V 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 T.H.D. (%) 100 AF Output Voltage (mV) 1000 T.H.D. (%) 100 AF Output Voltage (mV) 1000 Input = 100dB fdev. = 64kHz fmod. = 1kHz Vcc = 3.0V 11.1 10.3 10.4 10.5 Frequency (MHz) 10.6 10.7 10.8 10.9 11.0 11.1 Frequency (MHz) c S Curve CDSCB10M7GF123-R0 CDSCB10M7GF126-R0 4.0 2.5 2.0 3.0 Volt (V) Volt (V) 1.5 1.0 2.0 0.5 0.0 10.3 10.4 10.5 10.6 10.7 10.8 Frequency (MHz) 10.9 11.0 11.1 1.0 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 Frequency (MHz) 15 51 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 Ceramic Discriminator 10.7MHz Applied IC Reference Table Please see the following table to reference applied IC. If you cannot find the IC part number you are seeking, please contact our sales representative. ex. : CDSCB10M7GA105A-R0 Suffix Number IC Manufacturer IC Part Number Suffix Number TA2003 031 034V TA2007 033 TDA1576T 051 TA2008A / AN 045 TDA6160X 038 TA2022 050 Panasonic AN7004 011 TA2057 057 AN7232 053 TA2099N 082 Freescale MC13156 049 TA2104AFN 080 MC13158 073 TA2104F 080A PC1391M 056 TA2111N / F / FN 077 NE604 020 TA2132 092 SA605 042 TA2132BP 092D SA626 047 TA2142FN 102 SA636DK 096 TA2149AN 100A ATMEL INFINEON Renesas NXP ROHM IC Part Number Suffix Number U4313B 081 U4490B IC Manufacturer TOSHIBA SA639 085 TA2149N 100 TDA1596T 120 TA2154FN 113 TEA5710 040 TA2159F 116 TEA5757HL 105A TA31161 072 TEA5762 / 5757 061 TA31275FN 123 UAA3220TS 098 TA7303P 008 BA1448 060 TA7640AP 006 BA4230AF 005 TA8122AN / AF 016 BA4234L 004 TA8132AN / AF 018 SAMSUNG S1A0903 118A TB2132FN 128 SANYO LA1225M 108A LA1814M 115 LA1823 101 LA1827M 083 LA1831 043 LA1832 / M 046 LA1833 086 LA1835 / M 048 LA1838 / M 079 LA7770 023 LV23000M 114 LV23100V 121 CX1691M 078 CX-20029 001 CXA1111 093 SONY CXA1238 027 CXA1238N 027N CX1343M 032 CXA1376AM 054 CXA1538M / N / S 069 CXA1611 075 CX3067M 076 T. I. TRF6901 119 TOKO TK14570L 122 TK14583V 112 TK14588V 109 52 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 Notice 1. Standard Reflow Soldering Conditions (1) Reflow Filter is soldered twice within the following temperature conditions. Temperature (C) c CERAFILr 10.7MHz Chip Type SFECF Series o Soldering and Mounting Peak (260C max.) 260 230 Pre-heating (150-180C) 100 Heating (230C) Gradual Cooling 30 sec. min. 60-120 sec. 40 sec. max. 120 sec. min. (2) Soldering Iron Filter is soldered at +3505C for 3.00.5 seconds. The soldering iron should not touch the filter while soldering. (3) Conditions for Placement Machines The component is recommended for use with placement machines that employ optical placement capabilities. The component might be damaged by excessive mechanical force. Please make sure that you have evaluated by using placement machines before going into mass production. Do not use placement machines that utilize mechanical positioning. Please contact Murata for details beforehand. (4) Other (a) The component may be damaged if excess mechanical stress is applied to it mounted on the printed circuit board. (b) Design layout of components on the PC board to minimize the stress imposed on the warp or flexure of the board. (c) After installing components, if solder is excessively applied to the circuit board, mechanical stress will cause destruction resistance characteristics to degrade. To prevent this, be extremely careful in determining shape and dimension before designing the circuit board diagram. (d) When the positioning claws and pick-up nozzle are worn, the load is applied to the components while positioning is concentrated on positioning accuracy, etc. Careful checking and maintenance are necessary to prevent unexpected trouble. (e) When correcting components with a soldering iron, the tip of the soldering iron should not directly touch the component. Depending on the soldering conditions, the effective area of terminations may be reduced. Solder containing Ag should be used to prevent electrode erosion. (f) Do not use strong acidity flux, more than 0.2wt% chlorine content, in reflow soldering. [Component Direction] Place the component lateral to the direction in which stress acts. [Component Layout Close to Board] Perforation A B Slit C Susceptibility to stress is in the order of : A>C>B Continued on the following page. 53 !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. P50E.pdf Sep.19,2012 Notice Continued from the preceding page. 2. Wash Do not clean or wash the component as it is not hermetically sealed. 3. Coating In case of overcoating the component, conditions such as material of resin, cure temperature, and so on should be evaluated well. o Storage and Operating Conditions 1. Product Storage Conditions Please store the products in a room where the temperature/humidity is stable, and avoid places where there are large temperature changes. Please store the products under the following conditions: Temperature: -10 to +40C Humidity: 15 to 85% R.H. 2. Expiration Date on Storage Expiration date (shelf life) of the products is six months after delivery under the conditions of a sealed and unopened package. Please use the products within six months after delivery. If you store the products for a long time (more than six months), use carefully because solderability may be degraded due to storage under poor conditions. Please confirm solderability and characteristics for the products regularly. 3. Notice on Product Storage (1) Please do not store the products in a chemical atmosphere (Acids, Alkali, Bases, Organic gas, Sulfides and so on), because quality and solderability may be degraded due to storage in a chemical atmosphere. (2) Please do not put the products directly on the floor without anything under them to avoid damp places and/or dusty places. (3) Please do not store the products in places such as a damp heated place or any place exposed to direct sunlight or excessive vibration. (4) Please use the products immediately after package is opened, because quality and solderability may be degraded due to storage under poor conditions. (5) To avoid cracking of ceramic element, please do not drop the products. 4. Other Please be sure to consult with our sales representative or engineer whenever the products are to be used in conditions not listed above. o Rating The component may be damaged if excessive mechanical stress is applied. o Handling 1. Accurate test circuit values are required to measure electrical characteristics. Miscorrelation may be caused if there is any deviation, especially stray capacitance, from the test circuit in the specification. 2. The components, packed in a moisture proof bag (dry pack), are sensitive to moisture. The following treatment is required before applying reflow soldering, to avoid reliability degradation caused by thermal stress. When unpacked, store the component in an atmosphere of reflow 30C and below 60%R.H., and solder within 1 week. 54 3. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 Notice 1. Standard Reflow Soldering Conditions (1) Reflow Filter is soldered twice within the following temperature conditions. Temperature (C) c CERAFILr 10.7MHz Chip Type SFECV/SFECK Series o Soldering and Mounting Peak (240C max.) 240 230 Pre-heating (150-180C) 100 Heating (230C) Gradual Cooling 30 sec. min. 60-120 sec. 30 sec. max. 120 sec. min. (2) Soldering Iron Filter is soldered at +3505C for 3.00.5 seconds. The soldering iron should not touch the filter while soldering. (3) Conditions for Placement Machines The component is recommended for use with placement machines that employ optical placement capabilities. Damage may result from excessive mechanical force. Please make sure that you have evaluated by using placement machines before going into mass production. Do not use placement machines that utilize mechanical positioning. Please contact Murata for details beforehand. (4) Other (a) The component may be damaged if excess mechanical stress is applied to it mounted on the printed circuit board. (b) Design layout of components on the PC board to minimize the stress imposed on the warp or flexure of the board. (c) After installing components, if solder is excessively applied to the circuit board, mechanical stress will cause destruction resistance characteristics to degrade. To prevent this, be extremely careful in determining shape and dimension before designing the circuit board diagram. (d) When the positioning claws and pick-up nozzle are worn, the load is applied to the components while positioning is concentrated to one positioning accuracy, etc. Careful checking and maintenance are necessary to prevent unexpected trouble. (e) When correcting components with a soldering iron, the tip of the soldering iron should not directly touch the component. Depending on the soldering conditions, the effective area of terminations may be reduced. Solder containing Ag should be used to prevent electrode erosion. (f) Do not use strong acidity flux, more than 0.2wt% chlorine content, in reflow soldering. [Component Direction] Put the component lateral to the direction in which stress acts. [Component Layout Close to Board] Perforation A B Slit C Susceptibility to stress is in the order of : A>C>B Continued on the following page. 55 !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. P50E.pdf Sep.19,2012 Notice Continued from the preceding page. 2. Wash Do not clean or wash the component as it is not hermetically sealed. 3. Coating In case of overcoating the component, conditions such as material of resin, cure temperature, and so on should be evaluated well. o Storage and Operating Conditions 1. Product Storage Conditions Please store the products in room where the temperature/humidity is stable, and avoid places where there are large temperature changes. Please store the products under the following conditions: Temperature: -10 to +40C Humidity: 15 to 85% R.H. 2. Expiration Date on Storage Expiration date (Shelf life) of the products is six months after delivery under the conditions of a sealed and unopened package. Please use the products within six months after delivery. If you store the products for a long time (more than six months), use carefully because the products may be degraded in solderability due to storage under poor conditions. Please confirm solderability and characteristics for the products regularly. 3. Notice on Product Storage (1) Please do not store the products in a chemical atmosphere (Acids, Alkali, Bases, Organic gas, Sulfides and so on), because quality and solderability may be degraded due to the storage in a chemical atmosphere. o Rating The component may be damaged if excessive mechanical stress is applied. o Handling 1. Accurate test circuit values are required to measure electrical characteristics. Miscorrelation may be caused if there is any deviation, especially stray capacitance, from the test circuit in the specification. 2. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. 56 (2) Please do not put the products directly on the floor without anything under them to avoid damp places and/or dusty places. (3) Please do not store the products in the places such as a damp heated place or any place exposed to direct sunlight or excessive vibration. (4) Please use the products immediately after package is opened, because quality and solderability may be degraded due to storage under the poor conditions. (5) To avoid cracking of ceramic element, please do not drop the products. 4. Other Please be sure to consult with our sales representative or engineer whenever the products are to be used in conditions not listed above. !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. P50E.pdf Sep.19,2012 Notice c CERAFILr 10.7MHz Lead Type SFELF Series o Soldering and Mounting The component cannot withstand washing. o Storage and Operating Conditions 1. Product Storage Conditions Please store the products in room where the temperature/humidity is stable, and avoid such places where there are large temperature changes. Please store the products under the following conditions: Temperature: -10 to +40C Humidity: 15 to 85% R.H. 2. Expiration Date on Storage Expiration date (Shelf life) of the products is six months after delivery under the conditions of a sealed and unopened package. Please use the products within six months after delivery. If you store the products for a long time (more than six months), use carefully because the products may be degraded in solderability due to storage under poor conditions. Please confirm solderability and characteristics for the products regularly. 3. Notice on Product Storage (1) Please do not store the products in a chemical atmosphere (Acids, Alkali, Bases, Organic gas, Sulfides and so on), because quality and solderability may be degraded due to the storage in a chemical atmosphere. (2) Please do not put the products directly on the floor without anything under them to avoid damp places and/or dusty places. (3) Please do not store the products in the places such as a damp heated place or any place exposed to direct sunlight or excessive vibration. (4) Please use the products immediately after package is opened, because quality and solderability may be degraded due to storage under the poor conditions. (5) To avoid cracking of ceramic element, please do not drop the products. 4. Other Please be sure to consult with our sales representative or engineer whenever the products are to be used in conditions not listed above. o Rating The component may be damaged if excessive mechanical stress is applied. o Handling 1. Do not use this product with bend. The component may be damaged if excess mechanical stress is applied to it mounted on the printed circuit board. 2. Do not apply any type of reflow soldering on the component. 3. Do not clean or wash the component as it is not hermetically sealed. 4. Do not use strong acidity flux, more than 0.2wt% chlorine content, in flow soldering. 5. In case of overcoating the component, conditions such as material of resin, cure temperature, and so on should be evaluated well. 6. Accurate test circuit values are required to measure electrical characteristics. It may be a cause of miscorrelation if there is any deviation, especially stray capacitance, from the test circuit in the specification. 7. For safety purposes, avoid applying a direct current between the terminals. 57 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 Notice 1. Standard Reflow Soldering Conditions (1) Reflow Filter is soldered twice within the following temperature conditions. Temperature (C) c CERAFILr 4.5-6.5MHz Chip Type SFSKA Series o Soldering and Mounting Peak (260C max.) 260 230 Pre-heating (150-180C) 100 Heating (230C) Gradual Cooling 30 sec. min. 60-120 sec. 40 sec. max. 120 sec. min. (2) Soldering Iron Filter is soldered at +3505C for 3.00.5 seconds. The soldering iron should not touch the filter while soldering. (3) Conditions for Placement Machines The component is recommended for use with placement machines that employ optical placement capabilities. Damage may result from excessive mechanical force. Please make sure that you have evaluated by using placement machines before going into mass production. Do not use placement machines that utilize mechanical positioning. Please contact Murata for details beforehand. (4) Other (a) The component may be damaged if excess mechanical stress is applied to it mounted on the printed circuit board. (b) Design layout of components on the PC board to minimize the stress imposed on the warp or flexure of the board. (c) After installing chips, if solder is excessively applied to the circuit board, mechanical stress will cause destruction resistance characteristics to degrade. To prevent this, be extremely careful in determining shape and dimension before designing the circuit board diagram. (d) When the positioning claws and pick-up nozzle are worn, the load is applied to the components while positioning is concentrated to one positioning accuracy, etc. Careful checking and maintenance are necessary to prevent unexpected trouble. (e) When correcting chips with a soldering iron, the tip of the soldering iron should not directly touch the chip component. [Component Direction] Put the component lateral to the direction in which stress acts. [Component Layout Close to Board] Perforation A Susceptibility to stress is in the order of : A>C>B B Slit C 2. Wash Do not clean or wash the component as it is not hermetically sealed. Continued on the following page. 58 !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. P50E.pdf Sep.19,2012 Notice Continued from the preceding page. 3. Coating In case of overcoating the component, conditions such as material of resin, cure temperature, and so on should be evaluated well. o Storage and Operating Conditions 1. Product Storage Conditions Please store the products in room where the temperature/humidity is stable, and avoid places where there are large temperature changes. Please store the products under the following conditions: Temperature: -10 to +40C Humidity: 15 to 85% R.H. 2. Expiration Date on Storage Expiration date (Shelf life) of the products is six months after delivery under the conditions of a sealed and unopened package. Please use the products within six months after delivery. If you store the products for a long time (more than six months), use carefully because the products may be degraded in solderability due to storage under poor conditions. Please confirm solderability and characteristics for the products regularly. 3. Notice on Product Storage (1) Please do not store the products in a chemical atmosphere (Acids, Alkali, Bases, Organic gas, Sulfides and so on), because quality and solderability may be degraded due to the storage in a chemical atmosphere. (2) Please do not put the products directly on the floor without anything under them to avoid damp places and/or dusty places. (3) Please do not store the products in the places such as a damp heated place or any place exposed to direct sunlight or excessive vibration. (4) Please use the products immediately after package is opened, because quality and solderability may be degraded due to storage under the poor conditions. (5) To avoid cracking of ceramic element, please do not drop the products. 4. Other Please be sure to consult with our sales representative or engineer whenever the products are to be used in conditions not listed above. o Rating The component may be damaged if excessive mechanical stress is applied. o Handling 1. Accurate test circuit values are required to measure electrical characteristics. Miscorrelation may be caused if there is any deviation, especially stray capacitance, from the test circuit in the specification. 2. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. 59 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 Notice 1. Standard Reflow Soldering Conditions (1) Reflow Filter is soldered twice within the following temperature conditions. Temperature (C) c CERAFILr 2.3-5.7MHz Chip Type SFSKB Series o Soldering and Mounting Peak (260C max.) 260 200 Pre-heating (150-170C) 100 Heating (200C) Gradual Cooling 30 sec. min. 60-120 sec. 60 sec. max. 120 sec. min. (2) Soldering Iron Filter is soldered at +3505C for 3.00.5 seconds. The soldering iron should not touch the filter while soldering. (3) Conditions for Placement Machines The component is recommended for use with placement machines that employ optical placement capabilities. Damage may result from excessive mechanical force. Please make sure that you have evaluated by using placement machines before going into mass production. Do not use placement machines that utilize mechanical positioning. Please contact Murata for details beforehand. (4) Other (a) The component may be damaged if excess mechanical stress is applied to it mounted on the printed circuit board. (b) Design layout of components on the PC board to minimize the stress imposed on the warp or flexure of the board. (c) After installing components, if solder is excessively applied to the circuit board, mechanical stress will cause destruction resistance characteristics to degrade. To prevent this, be extremely careful in determining shape and dimension before designing the circuit board diagram. (d) When the positioning claws and pick-up nozzle are worn, the load is applied to the components while positioning is concentrated to one positioning accuracy, etc. Careful checking and maintenance are necessary to prevent unexpected trouble. (e) When correcting components with a soldering iron, the tip of the soldering iron should not directly touch the component. Depending on the soldering conditions, the effective area of terminations may be reduced. Solder containing Ag should be used to prevent the electrode erosion. (f) Do not use strong acidity flux, more than 0.2wt% chlorine content, in reflow soldering. [Component Direction] Put the component laterally to the direction in which stress acts. [Component Layout Close to Board] Perforation A Susceptibility to stress is in the order of : A>C>B B Slit C Continued on the following page. 60 !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. P50E.pdf Sep.19,2012 Notice Continued from the preceding page. 2. Wash Do not clean or wash the component as it is not hermetically sealed. 3. Coating In case of overcoating the component, conditions such as material of resin, cure temperature, and so on should be evaluated well. o Storage and Operating Conditions 1. Product Storage Conditions Please store the products in room where the temperature/humidity is stable, and avoid places where there are large temperature changes. Please store the products under the following conditions: Temperature: -10 to +40C Humidity: 15 to 85% R.H. 2. Expiration Date on Storage Expiration date (Shelf life) of the products is six months after delivery under the conditions of a sealed and unopened package. Please use the products within six months after delivery. If you store the products for a long time (more than six months), use carefully because the products may be degraded in solderability due to storage under poor conditions. Please confirm solderability and characteristics for the products regularly. 3. Notice on Product Storage (1) Please do not store the products in a chemical atmosphere (Acids, Alkali, Bases, Organic gas, Sulfides and so on), because quality and solderability may be degraded due to the storage in a chemical atmosphere. (2) Please do not put the products directly on the floor without anything under them to avoid damp places and/or dusty places. (3) Please do not store the products in the places such as a damp heated place or any place exposed to direct sunlight or excessive vibration. (4) Please use the products immediately after package is opened, because quality and solderability may be degraded due to storage under the poor conditions. (5) To avoid cracking of ceramic element, please do not drop the products. 4. Other Please be sure to consult with our sales representative or engineer whenever the products are to be used in conditions not listed above. o Rating The component may be damaged if excessive mechanical stress is applied. o Handling 1. Accurate test circuit values are required to measure electrical characteristics. Miscorrelation may be caused if there is any deviation, especially stray capacitance, from the test circuit in the specification. 2. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. 61 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 Notice c CERAFILr 455kHz Chip Type SFPKA Series o Soldering and Mounting 1. Standard Reflow Soldering Conditions (1) Reflow Filter is soldered twice within the following temperature conditions. 0EAK (260C max.) Temperature (C) 260 230 Heating (230C) Pre-heating 100 (150-180C) 30 sec. min. 60-120 sec. Gradual Cooling SEC max. 120 sec. min. (2) Soldering Iron Electrode is directly soldered with the tip of soldering iron at +3505C for 3.00.5 seconds. (3) Other Do not use strong acidity flux, more than 0.2wt% chlorine content, in reflow soldering. 2. Wash (1) Cleaning Solvent CFC alternatives (HCFC Series), Isopropyl Alcohol (IPA), 7ATER $EMINERALIZED 7ATER #LEANING 7ATER 3OLUTION (Cleanthrough-750H, Pine Alpha 100S), Silicon 4ECHNOCARE &27 (2) Cleaning Conditions s )MMERSION 7ASH 2 minutes max. in above solvent at +60C max. s 3HOWER OR 2INSE 7ASH 2 minutes max. in above solvent at +60C max. (3) Notice s 7HEN COMPONENTS ARE IMMERSED IN SOLVENT BE SURE TO maintain the temperature of components below the temperature of solvent. s 0LEASE DO NOT USE ULTRASONIC CLEANING s 4OTAL WASHING TIME SHOULD BE MINUTES MAXIMUM s 0LEASE ENSURE THE COMPONENT IS THOROUGHLY EVALUATED IN your application circuit. s 0LEASE DO NOT USE CHLORINE PETROLEUM OR ALKALI CLEANING solvent. s )F YOU PLAN TO USE ANY OTHER TYPES OF SOLVENTS PLEASE consult with Murata or a Murata representative prior to using. 3. Coating In case of overcoating the component, conditions such as material of resin, cure temperature, and so on should be evaluated well. Continued on the following page. 62 !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. P50E.pdf Sep.19,2012 Notice Continued from the preceding page. o Storage and Operating Conditions 1. Product Storage Conditions Please store the products in a room where the temperature/humidity is stable, and avoid places where there are large temperature changes. Please store the products under the following conditions: Temperature: -10 to +40C Humidity: 15 to 85% R.H. 2. Expiration Date on Storage Expiration date (shelf life) of the products is six months after delivery under the conditions of a sealed and unopened package. Please use the products within six months after delivery. If you store the products for a long time (more than six months), use carefully because solderability may be degraded due to storage under poor conditions. Please confirm solderability and characteristics for the products regularly. 3. Notice on Product Storage (1) Please do not store the products in a chemical atmosphere (Acids, Alkali, Bases, Organic gas, Sulfides and so on), because quality and solderability may be degraded due to storage in a chemical atmosphere. (2) Please do not put the products directly on the floor without anything under them to avoid damp places and/or dusty places. (3) Please do not store the products in places such as a damp heated place or any place exposed to direct sunlight or excessive vibration. (4) Please use the products immediately after package is opened, because quality and solderability may be degraded due to storage under poor conditions. (5) To avoid cracking of ceramic element, please do not drop the products. 4. Other Please be sure to consult with our sales representative or engineer whenever the products are to be used in conditions not listed above. o Rating The component may be damaged if excessive mechanical stress is applied. o Handling 1. If the component is cleaned, please confirm that the reliability has not been degraded. 2. The components, packed in a moisture-proof bag (dry pack), are sensitive to moisture. The following treatment is required before applying reflow soldering, to avoid package cracks or reliability degradation caused by thermal stress. When unpacked, store the component in an atmosphere of below 25C and below 65%R.H., and solder within 48 hours. 3. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. 63 !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. P50E.pdf Sep.19,2012 Notice c CERAFILr 455kHz Lead Type SFPLA/CFWLA/CFULA Series o Soldering and Mounting The component cannot withstand washing. o Storage and Operating Conditions 1. Product Storage Conditions Please store the products in a room where the temperature/humidity is stable, and avoid places where there are large temperature changes. Please store the products under the following conditions: Temperature: -10 to +40C Humidity: 15 to 85% R.H. 2. Expiration Date on Storage Expiration date (shelf life) of the products is six months after delivery under the conditions of a sealed and unopened package. Please use the products within six months after delivery. If you store the products for a long time (more than six months), use carefully because solderability may be degraded due to storage under poor conditions. Please confirm solderability and characteristics for the products regularly. 3. Notice on Product Storage (1) Please do not store the products in a chemical atmosphere (Acids, Alkali, Bases, Organic gas, Sulfides and so on), because quality and solderability may be degraded due to storage in a chemical atmosphere. (2) Please do not put the products directly on the floor without anything under them to avoid damp places and/or dusty places. (3) Please do not store the products in places such as a damp heated place or any place exposed to direct sunlight or excessive vibration. (4) Please use the products immediately after package is opened, because quality and solderability may be degraded due to storage under poor conditions. (5) To avoid cracking of ceramic element, please do not drop the products. 4. Other Please be sure to consult with our sales representative or engineer whenever the products are to be used in conditions not listed above. o Rating The component may be damaged if excessive mechanical stress is applied. o Handling 1. Do not use this product with bend. The component may be damaged if excessive mechanical stress is applied to it mounted on the printed circuit board. 2. All kinds of reflow soldering must not be applied on the component. 3. Do not clean or wash the component as it is not hermetically sealed. 4. Do not use strong acidity flux, more than 0.2wt% chlorine content, in flow soldering. 64 5. Conformal coating of the component is not acceptable due to non-sealed construction. 6. Accurate test circuit values are required to measure electrical characteristics. Miscorrelation may be caused if there is any deviation, especially stray capacitance, from the test circuit in the specification. 7. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 Notice 1. Standard Reflow Soldering Conditions (1) Reflow Filter is soldered twice within the following temperature conditions. Temperature (C) c Ceramic Trap 4.5-6.5MHz Chip Type TPSKA Series o Soldering and Mounting Peak (260C max.) 260 230 Pre-heating (150-180C) 100 Heating (230C) Gradual Cooling 30 sec. min. 60-120 sec. 40 sec. max. 120 sec. min. (2) Soldering Iron Filter is soldered at +3505C for 3.00.5 seconds. The soldering iron should not touch the filter while soldering. (3) Conditions for Placement Machines The component is recommended for use with placement machines that employ optical placement capabilities. Damage may result from excessive mechanical force. Please make sure that you have evaluated by using placement machines before going into mass production. Do not use placement machines that utilize mechanical positioning. Please contact Murata for details beforehand. (4) Other (a) The component may be damaged if excess mechanical stress is applied to it mounted on the printed circuit board. (b) Design layout of components on the PC board to minimize the stress imposed on the warp or flexure of the board. (c) After installing chips, if solder is excessively applied to the circuit board, mechanical stress will cause destruction resistance characteristics to degrade. To prevent this, be extremely careful in determining shape and dimension before designing the circuit board diagram. (d) When the positioning claws and pick-up nozzle are worn, the load is applied to the components while positioning is concentrated to one positioning accuracy, etc. Careful checking and maintenance are necessary to prevent unexpected trouble. (e) When correcting chips with a soldering iron, the tip of the soldering iron should not directly touch the chip component. [Component Direction] Put the component lateral to the direction in which stress acts. [Component Layout Close to Board] Perforation A Susceptibility to stress is in the order of : A>C>B B Slit C 2. Wash Do not clean or wash the component as it is not hermetically sealed. Continued on the following page. 65 !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. P50E.pdf Sep.19,2012 Notice Continued from the preceding page. 3. Coating In case of overcoating the component, conditions such as material of resin, cure temperature, and so on should be evaluated well. o Storage and Operating Conditions 1. Product Storage Conditions Please store the products in room where the temperature/humidity is stable, and avoid places where there are large temperature changes. Please store the products under the following conditions: Temperature: -10 to +40C Humidity: 15 to 85% R.H. 2. Expiration Date on Storage Expiration date (Shelf life) of the products is six months after delivery under the conditions of a sealed and unopened package. Please use the products within six months after delivery. If you store the products for a long time (more than six months), use carefully because the products may be degraded in solderability due to storage under poor conditions. Please confirm solderability and characteristics for the products regularly. 3. Notice on Product Storage (1) Please do not store the products in a chemical atmosphere (Acids, Alkali, Bases, Organic gas, Sulfides and so on), because quality and solderability may be degraded due to the storage in a chemical atmosphere. o Rating The component may be damaged if excessive mechanical stress is applied. o Handling 1. Accurate test circuit values are required to measure electrical characteristics. Miscorrelation may be caused if there is any deviation, especially stray capacitance, from the test circuit in the specification. 2. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. 66 (2) Please do not put the products directly on the floor without anything under them to avoid damp places and/or dusty places. (3) Please do not store the products in the places such as a damp heated place or any place exposed to direct sunlight or excessive vibration. (4) Please use the products immediately after package is opened, because quality and solderability may be degraded due to storage under the poor conditions. (5) To avoid cracking of ceramic element, please do not drop the products. 4. Other Please be sure to consult with our sales representative or engineer whenever the products are to be used in conditions not listed above. P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 Notice 1. Standard Reflow Soldering Conditions (1) Reflow Filter is soldered twice within the following temperature conditions. Temperature (C) c Ceramic Discriminator 10.7MHz Chip Type CDSCB Series o Soldering and Mounting Peak (260C max.) 260 230 Pre-heating (150-180C) 100 Heating (230C) Gradual Cooling 30 sec. min. 60-120 sec. 40 sec. max. 120 sec. min. (2) Soldering Iron Filter is soldered at +3005C for 3.00.5 seconds. The soldering iron should not touch the filter while soldering. (3) Conditions for Placement Machines The component is recommended for use with placement machines that employ optical placement capabilities. The component might be damaged by excessive mechanical force. Please make sure that you have evaluated by using placement machines before going into mass production. Do not use placement machines that utilize mechanical positioning. Please contact Murata for details beforehand. (4) Other (a) The component may be damaged if excess mechanical stress is applied to it mounted on the printed circuit board. (b) Design layout of components on the PC board to minimize the stress imposed on the warp or flexure of the board. (c) After installing components, if solder is excessively applied to the circuit board, mechanical stress will cause destruction resistance characteristics to degrade. To prevent this, be extremely careful in determining shape and dimension before designing the circuit board diagram. (d) When the positioning claws and pick-up nozzle are worn, the load is applied to the components while positioning is concentrated on positioning accuracy, etc. Careful checking and maintenance are necessary to prevent unexpected trouble. (e) When correcting components with a soldering iron, the tip of the soldering iron should not directly touch the component. Depending on the soldering conditions, the effective area of terminations may be reduced. Solder containing Ag should be used to prevent electrode erosion. [Component Direction] Place the component laterally to the direction in which stress acts. [Component Layout Close to Board] Perforation B A Slit C Susceptibility to stress is in the order of : A>C>B Continued on the following page. 67 !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. P50E.pdf Sep.19,2012 Notice Continued from the preceding page. 2. Wash Do not clean or wash the component as it is not hermetically sealed. 3. Coating In case of overcoating the component, conditions such as material of resin, cure temperature, and so on should be evaluated well. o Storage and Operating Conditions 1. Product Storage Conditions Please store the products in a room where the temperature/humidity is stable, and avoid places where there are large temperature changes. Please store the products under the following conditions: Temperature: -10 to +40C Humidity: 15 to 85% R.H. 2. Expiration Date on Storage Expiration date (shelf life) of the products is six months after delivery under the conditions of a sealed and unopened package. Please use the products within six months after delivery. If you store the products for a long time (more than six months), use carefully because solderability may be degraded due to storage under poor conditions. Please confirm solderability and characteristics for the products regularly. 3. Notice on Product Storage (1) Please do not store the products in a chemical atmosphere (Acids, Alkali, Bases, Organic gas, Sulfides and so on), because quality and solderability may be degraded due to storage in a chemical atmosphere. o Rating The component may be damaged if excessive mechanical stress is applied. o Handling 1. Accurate test circuit values are required to measure electrical characteristics. Miscorrelation may be caused if there is any deviation, especially stray capacitance, from the test circuit in the specification. 2. For safety purposes, avoid applying a direct current between the terminals. 68 (2) Please do not put the products directly on the floor without anything under them to avoid damp places and/or dusty places. (3) Please do not store the products in places such as a damp heated place or any place exposed to direct sunlight or excessive vibration. (4) Please use the products immediately after package is opened, because quality and solderability may be degraded due to storage under poor conditions. (5) To avoid cracking of ceramic element, please do not drop the products. 4. Other Please be sure to consult with our sales representative or engineer whenever the products are to be used in conditions not listed above. P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 Packaging c Minimum Quantity Taping o330mm o180mm Ammo Pack Bulk 1,500 500 Magazine Box CERAFILr<10.7MHz> SFECF 2,000 SFECV/SFECK 2,000 SFELF CERAFILr<2.3-6.5MHz> SFSKA 3,000 SFSKB 3,000 CERAFILr<455kHz> 200 CFULA CFWLA 1,000 50 150 SFPLA 1,000 50 200 TPSKA 3,000 Ceramic Traps<4.5-6.5MHz> Ceramic Discriminators<10.7MHz> 2,000 CDSCB c CERAFILr 10.7MHz Chip Type SFECF Series Dimensions of Carrier Tape Dimensions of Reel Cover film 0.30.05 Peeling strength (0.1 to 0.7N) +0.1 3.35 -0.05 (3) 10 max. Empty 3 max. Leader Cover film Components Empty 240 to 280 o13.00.5 400 to 560 180 +0 -1.5 60 +1.0 -0 12.00.2 5.50.05 1.840.1 4.00.1 (0.05) 4.10.1 Chip filter 2.00.5 4.10.1 o1.550.05 2.00.05 Trailer 160 to 190 1.750.1 4.00.1 17.01.0 13.0 +1.0 -0 User direction of feed ( ): Reference (in mm) s 0ART NUMBER MARKED SIDE IS ALWAYS FACING UP c CERAFILr 10.7MHz Chip Type SFECV/SFECK Series Dimensions of carrier tape Trailer 160-190 1.750.1 +0 Empty 240-280 400-560 180 -1.5 +1.0 o13.00.5 60 -0 Leader Cover film Empty Components 12.00.2 4.00.1 5.50.05 2.00.05 7.30.01 +0.1 o1.5 -0.0 Dimensions of reel 1.90.1 (3) +0.1 Chip filter Peeling strength 0.1 to 0.7N Cover film 10 max. 1.7 -0.05 3.00.1 0.30.05 2.00.5 4.00.1 +1.0 13.0 -0 17.01.0 User direction of feed s 0ART NUMBER MARKED SIDE IS ALWAYS FACING UP ( ) : Reference (in mm) Continued on the following page. 69 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 Packaging Continued from the preceding page. c CERAFILr 10.7MHz Lead Type SFELF Series P2 dh dh P H0 W0 W1 W L2 L1 W2 dS1 F 1 F1 P1 D0 F t P0 Item Code Dimensions Tolerance Lead length under the hold down tape L1 3.0 min. Length of cut-off L2 2.0 max. Pitch of components P 12.7 0.5 Pitch of sprocket hole (1) P0 12.7 0.2 Length from hole center to lead P1 3.85 0.5 Length from hole center to component center P2 6.35 Lead spacing (1) F 5.0 Lead spacing (2) F1 2.5 0.5 +0.5 -0.2 0.2 Slant forward or backward dh 0 1.0 Slant to the left or right dS1 0 1.0 0.5 - Width of carrier tape W 18.0 Width of hold down tape W0 6.0 min. Position of sprocket hole W1 9.0 0.5 Gap of hold down tape and carrier tape W2 0 +0.5 -0 Distance between the center of sprocket hole and lead stopper H0 18.0 0.5 Diameter of sprocket hole D0 o4.0 0.2 0.6 0.2 254.0 1.5 Total tape thickness Pitch of sprocket hole (2) t P020 Remarks To distinguish the direction - Hold down tape doesn't exceed the carrier tape The pitch of 20 sprocket holes (in mm) Continued on the following page. 70 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 Packaging Continued from the preceding page. c CERAFILr 4.5-6.5MHz Chip Type SFSKA Series Chip filter (3) Leader Cover film 16.00.2 Trailer 160 to 190 Empty Components 2.20.5 Empty 240 to 280 min. 400 to 560 801 3302 4.30.1 8.00.1 10 max. +0.1 Peeling strength (0.1 to 0.7N) Cover film 2.1-0.05 +0.1 o1.5 -0.0 0.30.05 9.00.1 7.50.1 2.00.1 4.00.1 o1.5 -0.0 2.30.1 +0.1 Dimensions of Reel 1.750.1 Dimensions of Carrier Tape o13.00.2 17.50.5 21.51.0 User direction of feed s 0ART NUMBER MARKED SIDE IS ALWAYS FACING UPSIDE (in mm) c CERAFILr 2.3-5.7MHz Chip Type SFSKB Series Empty Components 400 to 560 8.00.1 1.60.1 2.20.2 o13.00.2 Cover Film 4.20.1 Empty 240 to 280 (o80) (o330) Leader Cover Film Trailer 160 to 190 5.60.1 5.50.1 +0.1 o1.5 -0.0 12.00.2 4.00.1 2.00.1 Dimensions of Reel 1.750.1 Dimensions of Carrier Tape 5SER DIRECTION OF FEED Label 13.51.0 17.51.5 s 0ART .UMBER MARKED SIDE IS ALWAYS FACING UPSIDE (in mm) c CERAFILr 455kHz Chip Type SFPKA Series Dimensions of Carrier Tape Trailer 160 to 190 1.750.1 Empty Leader Cover film Components Empty 240 to 280 o13.00.2 3302 400 to 560 801 8.80.1 +0.1 -0 7.50.1 2.00.1 o1.5 16.00.2 4.00.1 Dimensions of Reel 2.20.5 12.00.1 User direction of feed 5.30.1 Cover film 17.50.5 Label 21.51.0 7.40.1 s 0ART NUMBER MARKED SIDE IS ALWAYS FACING UP (in mm) Continued on the following page. 71 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 Packaging Continued from the preceding page. c CERAFILr 455kHz Lead Type SFPLA Series Standard of Magazine Cassette 9.00.3 4051.0 7.60.25 8.10.3 100.3 2. Quality of Magazine (1) Transparent so that input / output direction is visually recognizable. (2) With an angle of 35 CERAFILr should slip down smoothly. (3) Antistatic finish (4) Recycling Note: Magazines should be sent back for recycling. (Therefore, empty magazines should not be damaged.) 3. Dimensions of Magazine Cassette 18.70.3 1. Putting CERAFILr into Magazine A magazine should contain 50pcs of CERAFILr, with ground terminals all facing toward the "Murata" mark on a magazine, and be closed with exclusive stoppers at both ends. Above should be the minimum packaging unit. 1.1 HP51M0003-02 1.1 (in mm) Tolerance unless otherwise specified: 0.2 Material: Polycarbonate Camber of Case: 1mm max. against entire length (reference) Twist of Case: 0.5mm max. (reference) c CERAFILr 455kHz Lead Type CFWLA Series Standard of Magazine Cassette 9.00.3 7.30.25 576.02.0 7.50.3 9.00.3 2. Quality of Magazine (1) Transparent so that input / output direction is visually recognizable. (2) With an angle of 35 CERAFILr should slip down smoothly. (3) Antistatic finish (4) Recycling Note: Magazines should be sent back for recycling. (Therefore, empty magazines should not be damaged.) 4. Dimensions of Magazine Cassette 18.70.3 1. Putting CERAFILr into Magazine A magazine should contain 50pcs of CERAFILr, with ground terminals all facing toward the "Murata" mark on a magazine, and be closed with exclusive stoppers at both ends. Above should be the minimum packaging unit. ANTISTATIC muRataHP51M0064 5.30.3 0.6 (in mm) Tolerance unless otherwise specified: 0.2 Material: Polycarbonate Camber of Case: 1mm max. against entire length (reference) Twist of Case: 0.5mm max. (reference) 3. Magazine should be packaged in a cardboard box. MURATA model name, quantity and outgoing inspection number should be indicated on the box. Cardboard box may contain maximum 33 magazines (1,650 pieces of filter). Continued on the following page. 72 P50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.19,2012 Packaging Continued from the preceding page. c Ceramic Trap 4.5-6.5MHz Chip Type TPSKA Series Leader Cover film 16.00.2 Trailer 160 to 190 Empty Components Empty 240 to 280 min. 2.20.5 400 to 560 801 3302 Chip filter (3) 10 max. +0.1 4.30.1 8.00.1 0.30.05 Peeling strength (0.1 to 0.7N) Cover film +0.1 o1.5 -0.0 2.1-0.05 9.00.1 7.50.1 2.00.1 4.00.1 o1.5 -0.0 2.30.1 +0.1 Dimensions of Reel 1.750.1 Dimensions of Carrier Tape o13.00.2 17.50.5 21.51.0 User direction of feed s 0ART NUMBER MARKED SIDE IS ALWAYS FACING UPSIDE (in mm) c Ceramic Discriminator 10.7MHz Chip Type CDSCB Series $IMENSIONS OF #ARRIER 4APE o1.5 2.00.05 Dimensions of reel 1.750.1 4.00.1 +0.1 -0 4RAILER 160 to 190 ,EADER Cover film 10 Cover film (3) User direction of feed s 0ART NUMBER MARKED SIDE IS ALWAYS FACING UP 400 to 560 180 +0.1 -1.5 +0.1 60 -0 12.00.2 o13.00.2 %MPTY 240 to 280 2.00.5 MAX 2.20.1 1.10.1 4.70.1 +0.1 o1.5 -0 0.30.05 (9.0) 4.00.1 0EELING STRENGTH 0.1 to 0.7N 5.50.05 %MPTY #OMPONENTS +1.0 13.0 -0 17.01.0 ( ): Reference (in mm) 73 !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Part Number Index CDSCB * * * * * * * * * * Chip Ceramic Discriminators for FM * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * p47 CFULA * * * * * * * * * * Ceramic Filters (CERAFILr) for AM * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * p42 CFWLA * * * * * * * * * * Ceramic Filters (CERAFILr) for AM * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * p40, 42 SFECF * * * * * * * * * * Chip Ceramic Filters (CERAFILr) for FM * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * p5-6 SFECK * * * * * * * * * * Chip Ceramic Filters (CERAFILr) for FM * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * p11 SFECV * * * * * * * * * * Chip Ceramic Filters (CERAFILr) for FM * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * p11 SFELF * * * * * * * * * * Ceramic Filters (CERAFILr) for FM * * * * * * * * * * * * * * * * * * * * * * * p14, 17, 20-21, 23, 25, 27 SFPKA * * * * * * * * * * Chip Ceramic Filters (CERAFILr) for AM * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * p38 SFPLA * * * * * * * * * * Ceramic Filters (CERAFILr) for AM * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * p40, 42 SFSKA * * * * * * * * * * Chip Ceramic Filters (CERAFILr) for TV/VCR * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * p31 SFSKB * * * * * * * * * * Chip Ceramic Filters (CERAFILr) for TV/VCR * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * p34 TPSKA * * * * * * * * * * Chip Ceramic Traps * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * p45 74 P50E.pdf Sep.19,2012 !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. P50E.pdf Sep.19,2012