SPEC NO: DSAF2405 REV NO: V.6A DATE: JAN/23/2015 PAGE: 1 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101005046
T-1 3/4 (5mm) SOLID STATE LAMP
Part Number: WP7113ID14V High Efficiency Red
Features
zLow power consumption.
zPopular T-1 3/4 diameter package.
zGeneral purpose leads.
zReliable and rugged.
zLong life - solid state reliability.
zAvailable on tape and reel.
z14V internal resistor.
zRoHS compliant.
Descriptions
zThe High Efficiency Red source color devices are made
with Gallium Arsenide Phosphide on Gallium Phosphide
Orange Light Emitting Diode.
zElectrostatic discharge and power surge could damage
the LEDs.
zIt is recommended to use a wrist band or anti-
electrostatic glove when handling the LEDs.
zAll devices, equipments and machineries must be
electrically grounded.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Lead spacing is measured where the leads emerge from the package.
4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
SPEC NO: DSAF2405 REV NO: V.6A DATE: JAN/23/2015 PAGE: 2 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101005046
Selection Guide
Absolute Maximum Ratings at TA=25°C
Electrical / Optical Characteristics at TA=25°C
Notes:
1. 2mm below package base.
2. 5mm below package base.
Part No. Dice Lens Type
Iv (mcd) [2]
V= 14V
V
iewing
Angle [1]
Min. Typ. 2θ1/2
WP7113ID14V High Efficiency Red (GaAsP/GaP) Red Diffused
18 35
*10 *22
30°
Symbol Parameter Device Typ. Max. Units Test Conditions
λpeak Peak Wavelength High Efficiency Red 627 nm VF=14V
λD [1] Dominant Wavelength High Efficiency Red 617 nm VF=14V
Δλ1/2 Spectral Line Half-width High Efficiency Red 45 nm VF=14V
IF Forward Current High Efficiency Red 10.5 13.5 mA VF=14V
IR Reverse Current High Efficiency Red 10 uA VR = 5V
Parameter High Efficiency Red Units
Power dissipation 160 mW
Forward Voltage 16 V
Reverse Voltage 5 V
Operating Temperature -40°C To +70°C
Storage Temperature -40°C To +85°C
Lead Solder Temperature [1] 260°C For 3 Seconds
Lead Solder Temperature [2] 260°C For 5 Seconds
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity/ luminous Flux: +/-15%.
*Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Notes:
1. Wavelength: +/-1nm.
2. Wavelength value is traceable to the CIE127-2007 compliant national standards.
3. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
SPEC NO: DSAF2405 REV NO: V.6A DATE: JAN/23/2015 PAGE: 3 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101005046
High Efficiency Red WP7113ID14V
SPEC NO: DSAF2405 REV NO: V.6A DATE: JAN/23/2015 PAGE: 4 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101005046
PACKING & LABEL SPECIFICATIONS WP7113ID14V
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAF2405 REV NO: V.6A DATE: JAN/23/2015 PAGE: 5 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101005046
SPEC NO: DSAF2405 REV NO: V.6A DATE: JAN/23/2015 PAGE: 6 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101005046
