Versafit V4 Very-thin-wall, highly flame-retardant, metric-sized heat-shrinkable tubing Versafit V4 heat-shrinkable tubing is a cost-effective, environmentally friendly choice for many commercial applications. Versafit V4 tubing is a very thin-wall version of Versafit, a specially formulated polyolefin with low recovery temperature, excellent flexibility, and high flameretardance (VW-1). Versafit V4 tubing is typically applied where space savings is important, offering the ability to pack components more closely than is possible with standard tubings. Versafit V4 tubing can shrink more than twice as fast as standard products. This rapid shrinking may be important in the prevention of overheating of temperature-sensitive components. PBBs PBBOs and polybrominated biphenyl oxides (PBBOs). In Europe, these chemicals are classified as environmentally hazardous substances. Versafit V4 products are UL-recognized at 125C, 300 V, and CSA-certified at 125C, 150 V, with UL VW-1 and CSA OFT flame-retardancy ratings. Unlike other typical flame-retardant tubings, Versafit V4 tubing is free of polybrominated biphenyls (PBBs) Temperature rating Full recovery temperature: Continuous operating temperature: 90C -45C to 125C Specifications* (R) Type Versafit V4 Raychem RW-3023 UL E35586 VW-1 CSA LR31929 VW-1 *When ordering, always specify latest issue. Dimensions (millimeters) W Expanded as supplied Fully recovered after heating D Size 1.0 1.5 2.0 2.5 3.0 3.5 4.0 As supplied D Inside diameter 1.4 0.25 1.9 0.25 2.3 0.25 2.8 0.25 3.3 0.25 3.8 0.25 4.4 0.25 Wall thickness (nominal) 0.10 0.10 0.10 0.15 0.15 0.15 0.15 Fully recovered d (max.) W (min.) Inside Wall diameter thickness** 0.50 0.25 0.75 0.25 1.00 0.25 1.25 0.25 1.50 0.25 1.75 0.25 2.00 0.25 Size 5.0 6.0 7.0 8.0 9.0 10.0 As supplied D Inside diameter 5.5 0.25 6.5 0.40 7.5 0.40 8.5 0.40 9.5 0.40 10.5 0.50 d Wall thickness (nominal) 0.15 0.15 0.15 0.15 0.15 0.15 **Wall thickness will be less if tubing recovery is restricted during shrinkage. Ordering information Colors Size selection Standard packaging Marking Ordering description Standard Black Nonstandard Other colors available on request. Always order the largest size that will shrink snugly over the component being covered. On spools Marked with UL, CSA, and Japan -F- Mark legends. Specify product name, size, and color; for example, V4 2.0-0 (0=Black). Fully recovered d (max.) W (min.) Inside Wall diameter thickness** 2.5 0.25 3.0 0.28 3.5 0.28 4.0 0.28 4.5 0.28 5.0 0.28 Specification values Electrical Chemical Property Dimensions Longitudinal change ASTM D 2671 UL 224 Eccentricity (recovered) Tensile strength Ultimate elongation Secant modulus (as supplied) Low-temperature flexibility (1 hour at -30C/-22F) Heat shock (4 hours at 250C/482F) Heat aging (7 days at 158C/316F) Followed by tests for: Tensile strength Unit mm Requirement See reverse Method of test ASTM D 2671 percent percent percent MPa (psi) percent MPa (psi) +1, -15 +3, -3 30 maximum 10.3 (1500) minimum 200 minimum 103 (1.5 x 104) maximum ASTM D 2671 UL 224 ASTM D 2671 ASTM D 2671 ASTM D 2671 ASTM D 2671 No cracking UL 224 No cracking UL 224 UL 224 MPa (psi) Ultimate elongation Flexibility Dielectric withstand at 2500 V Dielectric breakdown percent Dielectric strength Restricted shrinkage Dielectric withstand at 2500 V Dielectric strength Volume resistivity Corrosive effect (7 days at 158C/316F) Copper stability (7 days at 158C/316F) kV/mm (volts/mil) seconds volts seconds kV/mm (volts/mil) ohm-cm Followed by test for: Ultimate elongation Flammability Water absorption (recovered) (24 hours at 23C/73F) Fungus resistance Followed by tests for: Tensile strength Ultimate elongation Dielectric strength percent percent 70% minimum of unaged specimens 100 minimum No cracking 60 minimum UL 224 UL 224 UL 224 ASTM D 2671 50% minimum of unaged specimens 19.7 (500) minimum Pass 60 minimum ASTM D 2671 ASTM D 2671 UL 224 ASTM D 2671 19.7 (500) minimum 1014 minimum No corrosion ASTM D 2671 ASTM D 2671 ASTM D 2671 No brittleness, glazing, cracking, or severe discoloration of tubing. No pitting or blackening of copper. ASTM D 2671 100 minimum Pass 0.5 maximum ASTM D 2671 UL 224, VW-1 ASTM D 2671 ISO 846 Method B MPa (psi) percent kV/mm (volts/mil) 10.3 (1500) minimum 200 minimum 19.7 (500) minimum ASTM D 2671 ASTM D 2671 ASTM D 2671 Note: Consult RW-3023 for specific details about test procedures. Versafit and Raychem are trademarks of Tyco Electronics Corporation. Users should independently evaluate the suitability of the product for their application. Tyco Electronics Corporation 300 Constitution Drive Menlo Park, CA 94025-1164 USA Tel: (800) 926-2425 (US & Canada) Tel: +1 (650) 361-3860 (All other countries) Faraday Road Dorcan, Swindon, SN3 5HH United Kingdom Tel: +44 1793 528171 3816 Noborito, Tama-ku Kawasaki, Kanagawa 214-8533 Japan Tel: +81 44 900 5102 Asia Pacific Headquarters 26 Ang Mo Kio, Industrial Park 2 Singapore 569507 Tel: +65 4866 151 All information, including illustrations, is believed to be reliable. Users, however, should independently evaluate the suitability of each product for their application. Tyco Electronics Corporation makes no warranties as to the accuracy or completeness of the information, and disclaims any liability regarding its use. Tyco Electronics Corporation's only obligations are those in the Standard Terms and Conditions of Sale for these products and in no case will Tyco Electronics Corporation be liable for any incidental, indirect, or consequential damages arising from the sale, resale, use, or misuse of the product. Tyco Electronics Corporation's Specifications are subject to change without notice. In addition, Tyco Electronics Corporation reserves the right to make changes in materials or processing without notification to the Buyer which do not affect compliance with any applicable specification. For more information about this product visit www.tycoelectronics.com (c) 1995, 2002 Tyco Electronics Corporation Printed in USA 1654074 Revised 04/04 Physical