FUJITSU MICROELECTRONICS
DATA SHEET
Copyright©2006-2008 FUJITSU MICROELECTRONICS LIMITED All rights reserved
2008.9
The information for microcontroller supports is shown in the following homepage.
Be sure to refer to the "Check Sheet" for the latest cautions on development.
"Check Sheet" is seen at the following support page
"Check Sheet" lists the minimal requirement items to be checked to prevent problems beforehand in
system development.
http://edevice.fujitsu.com/micom/en-support/
16-bit Microcontroller
CMOS
F2MC-16LX MB90860E Series
MB90867E(S)/F867E(S)/V340E-101/V340E-102
■DESCRIPTION
The MB90860E series with integrated Flash ROM is a general-purpose Fujitsu 16-bit microcontroller designed
for automotive and other industrial applications. By utilizing new 0.35 µm CMOS technology, Fujitsu Microelec-
tronics now offers a 128KBytes of on-chip Flash ROM program memory.
Furthermore, the 3 V power supply of the internal MCU core is supplied by an internal regulator circuit, making
this a vastly superior product in terms of reliability and power consumption.
Note : F2MC is the abbreviation of FUJITSU Flexible Microcontroller.
■FEATURES
• CPU
• Optimal instruction suitable for controller applications
- Wide range of data types (bit, byte, word, and long word)
- Wide range of addressing modes (23 types)
- Enhanced multiplication and division instructions, and enhanced RETI instruction
- Enhanced high-precision calculations using a 32-bit accumulator
• Instruction set level support for high level languages (C language) and multitask
- Equipped with a system stack pointer
- A variety of enhanced pointer indirect instructions
- Barrel shift instructions
• Increased processing speed
- 4-byte instruction queue
(Continued)
DS07-13748-5E
MB90860E Series
2DS07-13748-5E
(Continued)
• Serial interface
• LIN-UART : 4 channels
- Equipped with full-duplex double buffer
- Clock-asynchronous and clock-synchronous serial transmission are available
•I
2C interface : 2 channels
- Up to 400 kbps transfer rate
• Interrupt controller
• Powerful interrupt function with 8 levels and 34 sources
• Supports up to 16 external interrupts
• CPU-independent automatic data transfer function
- Expanded intelligent I/O service function (EI2OS) : up to 16 channels
• I/O ports
• General-purpose input/output ports (CMOS output)
- 80 ports (devices without an S suffix in the part number - devices that support a sub clock)
- 82 ports (devices with an S suffix in the part number - devices that do not support a sub clock)
• 8/10-bit A/D converter : 24 channels
• Resolution is selectable between 8-bit and 10-bit.
• Can be activated by an external trigger.
• Conversion time : 3 µs (at 24-MHz machine clock, including sampling time)
• Address match detection (program patch) function
• Address match detection for 6 address pointers
• Timers
• Time-base timer, watch timer, watchdog timer : 1 channel
• 8/16-bit PPG timer : 8-bit × 16 channels or 16-bit × 8 channels
• 16-bit reload timer : 4 channels
• 16-bit I/O timer
- 16-bit free run timer : 2 channel (FRT0 : ICU 0/1/2/3, OCU 0/1/2/3, FRT1 : ICU 4/5/6/7, OCU 4/5/6/7)
- 16-bit input capture (ICU) : 8 channels
- 16-bit output compare (OCU) : 8 channels
• Low power consumption (standby) modes
• Sleep mode (a mode where the CPU operating clock stops)
• Time-base timer mode (a mode where only the oscillator clock, sub clock, time-base timer, and watch timer
operate)
• Watch mode (a mode where only the sub clock and watch timer operate)
• Stop mode (a mode where the oscillator clock and sub clock stop)
• CPU blocking operation mode
• Clock modulator
• Technology
•0.35 µm CMOS technology
MB90860E Series
DS07-13748-5E 3
■PRODUCT LINEUP
(Continued)
MB90867E(S) MB90F867E(S) MB90V340E-101/102
CPU F2MC-16LX CPU
Type MASK ROM product Flash memory product Evaluation product
System clock On-chip PLL clock multiplier (×1, ×2, ×3, ×4, ×6, 1/2 when PLL stops)
Minimum instruction execution time : 42 ns (4 MHz osc. PLL × 6)
ROM MASK ROM
128 Kbytes
Flash memory
128 Kbytes External
RAM 6 Kbytes 6 Kbytes 30 Kbytes
Dedicated power
supply for emulator* ⎯Yes
Technology
0.35 µm CMOS with on-chip
voltage regulator for internal
power supply
0.35 µm CMOS with on-chip
voltage regulator for internal
power supply + Flash memory
with on-chip charge pump for
programming voltage
0.35 µm CMOS with on-
chip voltage regulator for
internal power supply
Operating
voltage range
3.5 V to 5.5 V : during normal operation (not using A/D converter)
4.0 V to 5.5 V : when using A/D converter/Flash programming
4.5 V to 5.5 V : when using external bus
5 V ± 10%
Temperature range −40 °C to +105 °C⎯
Package QFP-100, LQFP-100 PGA-299
LIN-UART
4 channels 5 channels
Wide range of baud rate settings using a dedicated baud rate generator (reload timer)
Special synchronous options for adapting to different synchronous serial protocols
LIN functionality can operate as either master or slave LIN device
I2C (400 kbps) 2 channels
8/10-bit
A/D converter
24 channels
10-bit or 8-bit resolution
Conversion time : Min 3 µs include sample time (per one channel)
16-bit reload timer
(4 channels)
Operation clock frequency : fsys/21, fsys/23, fsys/25 (fsys = Machine clock frequency)
Supports External Event Count function
16-bit
free run timer
(2 channels)
Generates an interrupt on overflow
Supports Timer Clear when a match with Output Compare (ch.0, ch.4)
Operation clock freq. : fsys, fsys/21, fsys/22, fsys/23, fsys/24, fsys/25, fsys/26, fsys/27
(fsys = Machine clock freq.)
Free run Timer 0 (clock input FRCK0) corresponds to ICU 0/1/2/3, OCU 0/1/2/3
Free run Timer 1 (clock input FRCK1) corresponds to ICU 4/5/6/7, OCU 4/5/6/7
16-bit output
compare
(8 channels)
Generates an interrupt when the 16-bit free run timer matches the output compare register.
Multiple compare registers can be used to generate an output signal.
16-bit input capture
(8 channels)
Captures the value of the 16-bit free run timer and generates an interrupt when triggered
by a pin input (rising edge, falling edge, or both rising and falling edges).
Part Number
Parameter
MB90860E Series
4DS07-13748-5E
(Continued)
* : Configured by the jumper switch (TOOL VCC) when the emulator (MB2147-01) is used.
Please refer to the Emulator hardware manual for details.
MB90867E(S) MB90F867E(S) MB90V340E-101/102
8/16-bit
programmable pulse
generator
(8 channels)
8 channels (16-bit) or 16 channels (8-bit)
8-bit reload counter × 16
8-bit reload registers for lower part × 16
8-bit reload registers for upper part × 16
Supports 8-bit and 16-bit operating modes
A pair of 8-bit reload counters can be configured as one 16-bit reload counter or as
an 8-bit prescaler plus an 8-bit reload counter
Operation clock freq. : fsys, fsys/21, fsys/22, fsys/23, fsys/24 or 128 µs@fosc = 4 MHz
(fsys = Machine clock frequency, fosc = Oscillation clock frequency)
CAN interface ⎯3 channels
External interrupt
(16 channels)
Can be triggered by rising edge, falling edge, or H/L level inputs, external interrupts can
by used by expanded intelligent I/O services (EI2OS) and DMA
D/A converter ⎯2 channels
Sub clock (maximum
100 kHz) Devices without 'S' suffix in the part number Only for MB90V340E-
102
I/O ports
Virtually all external pins can be used as general-purpose I/O ports
All push-pull outputs
Bitwise configurable as input/output or peripheral signal
Configurable in blocks of 8 pins as CMOS schmitt trigger or automotive inputs
Configurable as TTL input levels for an external bus (only applies to the 32 external bus
pins)
Flash memory
Supports automatic programming, Embedded Algorithm
Write/Erase/Erase-Suspend/Resume commands
Equipped with a flag indicating completion of the algorithm
Number of erase cycles : 10,000 times
Data retention time : 20 years
Boot block configuration
Erase can be performed on each block
Block protection with external programming voltage
Flash Security Feature for protecting the content of the Flash
⎯
Part Number
Parameter
MB90860E Series
DS07-13748-5E 5
■PIN ASSIGNMENTS
• MB90V340E-101/102
(Continued)
(TOP VIEW)
(FPT-100P-M06)
* : X0A, X1A : MB90V340E-102
P40, P41 : MB90V340E-101
This pin assignment is for using MB90V340E-101/102 via probecable as MB90860E.
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
P04/AD04/INT12
P23/A19/PPGF(E)
P22/A18/PPGD(C)
P21/A17/PPGB(A)
P20/A16/PPG9(8)
P17/AD15/SCK4
P16/AD14/SOT4
P15/AD13/SIN4
X1
Vss
Vcc
P14/AD12/SCK3
P13/AD11/SOT3
P12/AD10/SIN3/INT11R
P11/AD09/TOT1
P10/AD08/TIN1
P07/AD07/INT15
P06/AD06/INT14
P05/AD05/INT13
X0
301 8
P75/AN21/INT5
P03/AD03/INT11
P02/AD02/INT10
P01/AD01/INT9
P00/AD00/INT8
PA1/TX0
PA0/RX0/INT8R
P97/OUT3
P96/OUT2
P95/OUT1
P94/OUT0
P93/PPG7(6)
P92/PPG5(4)
P91/PPG3(2)
P90/PPG1(0)
Vss
Vcc
P87/SCK1
P86/SOT1
P85/SIN1
P84/SCK0/INT15R
P83/SOT0/TOT2
P82/SIN0/TIN2/INT14R
P81/TOT0/CKOT/INT13R
P80/TIN0/ADTG/INT12R
P77/AN23/INT7
P76/AN22/INT6
MD0
MD1
MD2
P24/A20/IN0
P25/A21/IN1
P26/A22/IN2
P27/A23/IN3
P30/ALE/IN4
P34/HRQ/OUT4
P56/AN14/DA00
P55/AN13
P54/AN12/TOT3
P53/AN11/TIN3
P52/AN10/SCK2
P51/AN9/SOT2
P50/AN8/SIN2
P47/SCL1
P46/SDA1
P45/SCL0/FRCK1
P44/SDA0/FRCK0
P43/IN7/TX1
P42/IN6/RX1/INT9R
C
Vss
Vcc
P41/X1A*
P40/X0A*
P37/CLK/OUT7
P36/RDY/OUT6
QFP - 100
21201716 19181514131211 2625242322 27 2829435629710
80515871 70 67 6669 6865 64 6362 6176 75 74 7372777879 54 535556 5259 5760
P57/AN15/DA01
P74/AN20/INT4
P73/AN19/INT3
P72/AN18/INT2
P60/AN0/PPG0(1)
P61/AN1/PPG2(3)
P62/AN2/PPG4(5)
P63/AN3/PPG6(7)
P64/AN4/PPG8(9)
P65/AN5/PPGA(B)
P66/AN6/PPGC(D)
P67/AN7/PPGE(F)
Vss
P70/AN16/INT0
P71/AN17/INT1
AVcc
AVRH
AVRL
AVss
RST
P31/RD/IN5
P32/WRL/WR/RX2/INT10R
P33/WRH/TX2
P35/HAK/OUT5
MB90860E Series
6DS07-13748-5E
(Continued)
(TOP VIEW)
(FPT-100P-M20)
* : X0A, X1A : MB90V340E-102
P40, P41 : MB90V340E-101
This pin assignment is for using MB90V340E-101/102 via probecable as MB90860E.
75
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
P04/AD04/INT12
P23/A19/PPGF(E)
P22/A18/PPGD(C)
P21/A17/PPGB(A)
P20/A16/PPG9(8)
P17/AD15/SCK4
P16/AD14/SOT4
P15/AD13/SIN4
X1
Vss
Vcc
P14/AD12/SCK3
P13/AD11/SOT3
P12/AD10/SIN3/INT11R
P11/AD09/TOT1
P10/AD08/TIN1
P07/AD07/INT15
P06/AD06/INT14
P05/AD05/INT13
X0
P75/AN21/INT5
P74/AN20/INT4
P73/AN19/INT3
P72/AN18/INT2
P71/AN17/INT1
P70/AN16/INT0
Vss
P67/AN7/PPGE(F)
P66/AN6/PPGC(D)
P65/AN5/PPGA(B)
P64/AN4/PPG8(9)
P63/AN3/PPG6(7)
P62/AN2/PPG4(5)
P61/AN1/PPG2(3)
P60/AN0/PPG0(1)
AVss
AVRL
AVRH
AVcc
P57/AN15/DA01
P00/AD00/INT8
PA1/TX0
PA0/RX0/INT8R
P97/OUT3
P96/OUT2
P95/OUT1
P94/OUT0
P93/PPG7(6)
P92/PPG5(4)
P91/PPG3(2)
P90/PPG1(0)
Vss
Vcc
P87/SCK1
P86/SOT1
P85/SIN1
P84/SCK0/INT15R
P83/SOT0/TOT2
P82/SIN0/TIN2/INT14R
P81/TOT0/CKOT/INT13R
P80/TIN0/ADTG/INT12R
P77/AN23/INT7
P76/AN22/INT6
MD0
P26/A22/IN2
P27/A23/IN3
P30/ALE/IN4
P34/HRQ/OUT4
P53/AN11/TIN3
P52/AN10/SCK2
P51/AN9/SOT2
P50/AN8/SIN2
P47/SCL1
P46/SDA1
P45/SCL0/FRCK1
P44/SDA0/FRCK0
P43/IN7/TX1
P42/IN6/RX1/INT9R
C
Vss
Vcc
P41/X1A*
P40/X0A*
P37/CLK/OUT7
P36/RDY/OUT6
LQFP - 100
99P24/A20/IN0
100P25/A21/IN1
28P56/AN14/DA00
27 P55/AN13
26 P54/AN12/TOT3
49 MD2
50 MD1
78P03/AD03/INT11
77P02/AD02/INT10
76P01/AD01/INT9
74 7372 71 70 69 6867 66 65 64 6362 61 60 5859 555657 54 5352 51
123456789 1011121314 15 16 1817 212019 22 2324 25
RST
P31/RD/IN5
P32/WRL/WR/RX2/INT10R
P33/WRH/TX2
P35/HAK/OUT5
MB90860E Series
DS07-13748-5E 7
• MB90867E(S)/MB90F867E(S)
(Continued)
(TOP VIEW)
(FPT-100P-M06)
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
P04/AD04/INT12
P23/A19/PPGF(E)
P22/A18/PPGD(C)
P21/A17/PPGB(A)
P20/A16/PPG9(8)
P17/AD15
P16/AD14
P15/AD13
X1
Vss
Vcc
P14/AD12/SCK3
P13/AD11/SOT3
P12/AD10/SIN3/INT11R
P11/AD09/TOT1
P10/AD08/TIN1
P07/AD07/INT15
P06/AD06/INT14
P05/AD05/INT13
X0
P75/AN21/INT5
P03/AD03/INT11
P02/AD02/INT10
P01/AD01/INT9
P00/AD00/INT8
PA1
PA0/INT8R
P97/OUT3
P96/OUT2
P95/OUT1
P94/OUT0
P93/PPG7(6)
P92/PPG5(4)
P91/PPG3(2)
P90/PPG1(0)
Vss
Vcc
P87/SCK1
P86/SOT1
P85/SIN1
P84/SCK0/INT15R
P83/SOT0/TOT2
P82/SIN0/TIN2/INT14R
P81/TOT0/CKOT/INT13R
P80/TIN0/ADTG/INT12R
P77/AN23/INT7
P76/AN22/INT6
MD0
MD1
MD2
P24/A20/IN0
P25/A21/IN1
P26/A22/IN2
P27/A23/IN3
P30/ALE/IN4
P34/HRQ/OUT4
P56/AN14
P55/AN13
P54/AN12/TOT3
P53/AN11/TIN3
P52/AN10/SCK2
P51/AN9/SOT2
P50/AN8/SIN2
P47/SCL1
P46/SDA1
P45/SCL0/FRCK1
P44/SDA0/FRCK0
P43/IN7
P42/IN6/INT9R
C
Vss
Vcc
P41/X1A*
P40/X0A*
P37/CLK/OUT7
P36/RDY/OUT6
QFP - 100
80797877 76 75 74 7372 71 70 69 6867 66 65 64 6362 61 60 59 5857 56 55 54 5352 51
123456789 1011121314 15 16 17 1819 20 21 22 2324 25 26 27 2829 30
P74/AN20/INT4
P73/AN19/INT3
P72/AN18/INT2
P71/AN17/INT1
P70/AN16/INT0
P67/AN7/PPGE(F)
P66/AN6/PPGC(D)
P65/AN5/PPGA(B)
P64/AN4/PPG8(9)
P61/AN1/PPG2(3)
AVss
P57/AN15
AVcc
P60/AN0/PPG0(1)
AVRL
AVRH
Vss
P62/AN2/PPG4(5)
P63/AN3/PPG6(7)
RST
P31/RD/IN5
P33/WRH
P35/HAK/OUT5
P32/WRL/WR/INT10R
* : X0A, X1A : MB90867E, MB90F867E
P40, P41 : MB90867ES/MB90F867ES
MB90860E Series
8DS07-13748-5E
(Continued)
(TOP VIEW)
(FPT-100P-M20)
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
P04/AD04/INT12
P23/A19/PPGF(E)
P22/A18/PPGD(C)
P21/A17/PPGB(A)
P20/A16/PPG9(8)
P17/AD15
P16/AD14
P15/AD13
X1
Vss
Vcc
P14/AD12/SCK3
P13/AD11/SOT3
P12/AD10/SIN3/INT11R
P11/AD09/TOT1
P10/AD08/TIN1
P07/AD07/INT15
P06/AD06/INT14
P05/AD05/INT13
X0
P00/AD00/INT8
PA1
PA0/INT8R
P97/OUT3
P96/OUT2
P95/OUT1
P94/OUT0
P93/PPG7(6)
P92/PPG5(4)
P91/PPG3(2)
P90/PPG1(0)
Vss
Vcc
P87/SCK1
P86/SOT1
P85/SIN1
P84/SCK0/INT15R
P83/SOT0/TOT2
P82/SIN0/TIN2/INT14R
P81/TOT0/CKOT/INT13R
P80/TIN0/ADTG/INT12R
P77/AN23/INT7
P76/AN22/INT6
MD0
P26/A22/IN2
P27/A23/IN3
P30/ALE/IN4
P34/HRQ/OUT4
P53/AN11/TIN3
P52/AN10/SCK2
P51/AN9/SOT2
P50/AN8/SIN2
P47/SCL1
P46/SDA1
P45/SCL0/FRCK1
P44/SDA0/FRCK0
P43/IN7
P42/IN6/INT9R
C
Vss
Vcc
P41/X1A*
P40/X0A*
P37/CLK/OUT7
P36/RDY/OUT6
99P24/A20/IN0
100P25/A21/IN1
28P56/AN14
27 P55/AN13
26 P54/AN12/TOT3
49 MD2
50 MD1
78P03/AD03/INT11
77P02/AD02/INT10
76P01/AD01/INT9
LQFP - 100
75 74 7372 71 70 69 6867 66 65 64 6362 61 60 59 5857 56 55 54 5352 51
123456789 1011121314 15 16 17 1819 20 21 22 2324 25
P75/AN21/INT5
P74/AN20/INT4
P73/AN19/INT3
P72/AN18/INT2
P71/AN17/INT1
P70/AN16/INT0
Vss
P67/AN7/PPGE(F)
P66/AN6/PPGC(D)
P65/AN5/PPGA(B)
P64/AN4/PPG8(9)
P63/AN3/PPG6(7)
P62/AN2/PPG4(5)
P61/AN1/PPG2(3)
P60/AN0/PPG0(1)
AVss
AVRL
AVRH
AVcc
P57/AN15
RST
P31/RD/IN5
P33/WRH
P35/HAK/OUT5
P32/WRL/WR/INT10R
* : X0A, X1A : MB90867E, MB90F867E
P40, P41 : MB90867ES, MB90F867ES
MB90860E Series
DS07-13748-5E 9
■PIN DESCRIPTION
(Continued)
Pin No.
Pin name
I/O
Circuit
type*3
Function
QFP100*1LQFP100*2
1 to 4 99 to 2
P24 to P27
G
General-purpose I/O pins. It is possible to select whether or not a
pull-up resistance is used by configuring a register. In external
bus mode, each pin is enabled as a general-purpose I/O port
when the corresponding bit in the external address output control
register (HACR) is 1.
A20 to A23
External address bus output pins. When the corresponding bits in
the external address output control register (HACR) are 0, the
pins are enabled as high address output pins (A20 to A23).
IN0 to IN3 Trigger input pins for input captures 0 to 3.
53
P30
G
General-purpose I/O pin. It is possible to select whether or not a
pull-up resistance is used by configuring a register. This function
is enabled in single-chip mode.
ALE Address latch enable output pin. This function is enabled when
the external bus is enabled.
IN4 Trigger input pin for input capture 4.
64
P31
G
General-purpose I/O pin. It is possible to select whether or not a
pull-up resistance is used by configuring a register. This function
is enabled in single-chip mode.
RD External read strobe output pin. This function is enabled when the
external bus is enabled.
IN5 Trigger input pin for input capture 5.
75
P32
G
General-purpose I/O pin. It is possible to select whether or not a
pull-up resistance is used by configuring a register. This function
is enabled either in single-chip mode or when the WR/WRL pin
output disabled.
WR / WRL
Write strobe output pin for the external data bus. This function is
enabled when both the external bus and the WR/WRL pin output
are enabled. WRL is used as a write strobe output for the lower 8
bits of the data bus in 16-bit access while WR is used as the write
strobe for the 8 bits of the data bus in 8-bit access.
INT10R External interrupt request input pin (sub) .
86
P33
G
General-purpose I/O pin. It is possible to select whether or not a
pull-up resistance is used by configuring a register. This function
is enabled either in single-chip mode or when the WRH pin output
disabled.
WRH
Write strobe output pin for the upper 8 bits of the external data
bus. This function is enabled when the external bus is enabled,
and the external bus is in 16-bit mode, and the WRH output pin is
enabled.
MB90860E Series
10 DS07-13748-5E
(Continued)
Pin No.
Pin name
I/O
Circuit
type*3
Function
QFP100*1LQFP100*2
97
P34
G
General-purpose I/O pin. It is possible to select whether or not
a pull-up resistance is used by configuring a register. This
function is enabled either in single-chip mode or when the hold
function is disabled.
HRQ Hold request input pin. This function is enabled when both the
external bus and the hold function are enabled.
OUT4 Waveform output pin for output compare 4.
10 8
P35
G
General-purpose I/O pin. It is possible to select whether or not
a pull-up resistance is used by configuring a register. This
function is enabled either in single-chip mode or when the hold
function is disabled.
HAK Hold acknowledge output pin. This function is enabled when
both the external bus and the hold function are enabled.
OUT5 Waveform output pin for output compare 5.
11 9
P36
G
General-purpose I/O pin. It is possible to select whether or not
a pull-up resistance is used by configuring a register. This
function is enabled either in single-chip mode or when the
external ready function is disabled.
RDY External ready input pin. This function is enabled when both the
external bus and the external ready function are enabled.
OUT6 Waveform output pin for output compare 6.
12 10
P37
G
General-purpose I/O pin. It is possible to select whether or not
a pull-up resistance is used by configuring a register. This
function is enabled either in single-chip mode or when clock
output is disabled.
CLK Clock output pin. This function is enabled when both the
external bus and clock output are enabled.
OUT7 Waveform output pin for output compare 7.
13, 14 11, 12
P40, P41 F General-purpose I/O pins (devices with an “S” suffix in the part
number).
X0A , X1A B Input pins for sub-clock (devices without an "S" suffix in the part
number).
15 13 VCC ⎯Power (3.5 V to 5.5 V) input pin.
16 14 VSS ⎯GND pin.
17 15 C K
This is the power supply stabilization capacitor pin. It should be
connected to a ceramic capacitor with a capacitance of 0.1 µF
or higher.
18 16
P42
F
General-purpose I/O pin.
IN6 Trigger input pin for input capture 6.
INT9R External interrupt request input pin (sub) .
MB90860E Series
DS07-13748-5E 11
(Continued)
Pin No.
Pin name
I/O
Circuit
type*3
Function
QFP100*1LQFP100*2
19 17 P43 FGeneral-purpose I/O pin.
IN7 Trigger input pin for input capture 7.
20 18
P44
H
General-purpose I/O pin.
SDA0 Serial data I/O pin for I2C 0.
FRCK0 Input pin for 16-bit free run timer 0.
21 19
P45
H
General-purpose I/O pin.
SCL0 Serial clock I/O pin for I2C 0.
FRCK1 Input pin for 16-bit free run timer 1.
22 20 P46 HGeneral-purpose I/O pin.
SDA1 Serial data I/O pin for I2C 1.
23 21 P47 HGeneral-purpose I/O pin.
SCL1 Serial clock I/O pin for I2C 1.
24 22
P50
O
General-purpose I/O pin.
AN8 Analog input pin for the A/D converter.
SIN2 Serial data input pin for UART2.
25 23
P51
I
General-purpose I/O pin.
AN9 Analog input pin for the A/D converter.
SOT2 Serial data output pin for UART2.
26 24
P52
I
General-purpose I/O pin.
AN10 Analog input pin for the A/D converter.
SCK2 Clock I/O pin for UART2.
27 25
P53
I
General-purpose I/O pin.
AN11 Analog input pin for the A/D converter.
TIN3 Event input pin for reload timer 3.
28 26
P54
I
General-purpose I/O pin.
AN12 Analog input pin for the A/D converter.
TOT3 Output pin for reload timer 3.
29 27 P55 IGeneral-purpose I/O pin.
AN13 Analog input pin for the A/D converter.
30, 31 28, 29 P56, P57 JGeneral-purpose I/O pins.
AN14, AN15 Analog input pin for the A/D converter.
32 30 AVCC K Analog power input pin for the A/D converter.
MB90860E Series
12 DS07-13748-5E
(Continued)
Pin No.
Pin name
I/O
Circuit
type*3
Function
QFP100*1LQFP100*2
33 31 AVRH L
Reference voltage input pin for the A/D converter. This
power supply must be turned on or off while a voltage
higher than or equal to AVRH is applied to AVCC.
34 32 AVRL K Lower reference voltage input pin for the A/D converter.
35 33 AVSS K Analog GND pin for the A/D converter.
36 to 43 34 to 41
P60 to P67
I
General-purpose I/O pins.
AN0 to AN7 Analog input pins for the A/D converter.
PPG0, 2, 4, 6, 8,
A, C, E PPG output pins.
44 42 VSS ⎯GND pin.
45 to 50 43 to 48
P70 to P75
I
General-purpose I/O pins.
AN16 to AN21 Analog input pins for the A/D converter.
INT0 to INT5 External interrupt request input pins.
51 49 MD2 D Input pin for specifying the operating mode.
52, 53 50, 51 MD1, MD0 C Input pins for specifying the operating mode.
54 52 RST E Reset input.
55, 56 53, 54
P76, P77
I
General-purpose I/O pins.
AN22, AN23 Analog input pins for the A/D converter.
INT6, INT7 External interrupt request input pins.
57 55
P80
F
General-purpose I/O pin.
TIN0 Event input pin for reload timer 0.
ADTG Trigger input pin for the A/D converter.
INT12R External interrupt request input pin (sub) .
58 56
P81
F
General-purpose I/O pin.
TOT0 Output pin for reload timer 0.
CKOT Output pin for the clock monitor.
INT13R External interrupt request input pin (sub) .
59 57
P82
M
General-purpose I/O pin.
SIN0 Serial data input pin for UART0.
TIN2 Event input pin for reload timer 2.
INT14R External interrupt request input pin (sub) .
60 58
P83
F
General-purpose I/O pin.
SOT0 Serial data output pin for UART0.
TOT2 Output pin for reload timer 2.
MB90860E Series
DS07-13748-5E 13
(Continued)
Pin No.
Pin name
I/O
Circuit
type*3
Function
QFP100*1LQFP100*2
61 59
P84
F
General-purpose I/O pin.
SCK0 Clock I/O pin for UART0.
INT15R External interrupt request input pin (sub) .
62 60 P85 MGeneral-purpose I/O pin.
SIN1 Serial data input pin for UART1.
63 61 P86 FGeneral-purpose I/O pin.
SOT1 Serial data output pin for UART1.
64 62 P87 FGeneral-purpose I/O pin.
SCK1 Clock I/O pin for UART1.
65 63 VCC ⎯Power (3.5 V to 5.5 V) input pins.
66 64 VSS ⎯GND pins.
67 to 70 65 to 68 P90 to P93 FGeneral-purpose I/O pins.
PPG1, 3, 5, 7 PPG output pins.
71 to 74 69 to 72
P94 to P97
F
General-purpose I/O pins.
OUT0 to OUT3 Waveform output pins for output compare 0 to 3. This
function is enabled when waveform output is enabled.
75 73 PA0 FGeneral-purpose I/O pin.
INT8R External interrupt request input pin (sub) .
76 74 PA1 F General-purpose I/O pin.
77 to 84 75 to 82
P00 to P07
G
General-purpose I/O pins. It is possible to select whether
or not a pull-up resistance is used by configuring a regis-
ter. This function is enabled in single-chip mode.
AD00 to AD07
I/O pins for the lower 8 bits of the external address/data
bus. This function is enabled when the external bus is en-
abled.
INT8 to INT15 External interrupt request input pins.
85 83
P10
G
General-purpose I/O pin. It is possible to select whether
or not a pull-up resistance is used by configuring a regis-
ter. This function is enabled in single-chip mode.
AD08
I/O pin for the external address/data bus.
This function is enabled when the external bus is
enabled.
TIN1 Event input pin for reload timer 1.
MB90860E Series
14 DS07-13748-5E
(Continued)
Pin No.
Pin name
I/O
Circuit
type*3
Function
QFP100*1LQFP100*2
86 84
P11
G
General-purpose I/O pin. It is possible to select whether or not
a pull-up resistance is used by configuring a register. This
function is enabled in single-chip mode.
AD09 I/O pin for the external address/data bus.
This function is enabled when the external bus is enabled.
TOT1 Output pin for reload timer 1.
87 85
P12
N
General-purpose I/O pin. It is possible to select whether or not
a pull-up resistance is used by configuring a register. This
function is enabled in single-chip mode.
AD10 I/O pin for the external address/data bus.
This function is enabled when the external bus is enabled.
SIN3 Serial data input pin for UART3.
INT11R External interrupt request input pin (sub) .
88 86
P13
G
General-purpose I/O pin. It is possible to select whether or not
a pull-up resistance is used by configuring a register. This
function is enabled in single-chip mode.
AD11 I/O pin for the external address/data bus.
This function is enabled when the external bus is enabled.
SOT3 Serial data output pin for UART3.
89 87
P14
G
General-purpose I/O pin. It is possible to select whether or not
a pull-up resistance is used by configuring a register. This
function is enabled in single-chip mode.
AD12 I/O pin for the external address/data bus.
This function is enabled when the external bus is enabled.
SCK3 Clock I/O pin for UART3.
90 88 VCC ⎯Power (3.5 V to 5.5 V) input pin.
91 89 VSS ⎯GND pin.
92 90 X1 AMain clock output pin.
93 91 X0 Main clock input pin.
94 92
P15
G
General-purpose I/O pin. It is possible to select whether or not
a pull-up resistance is used by configuring a register. This
function is enabled in single-chip mode.
AD13 I/O pin for the external address/data bus.
This function is enabled when the external bus is enabled.
95 93
P16
G
General-purpose I/O pin. It is possible to select whether or not
a pull-up resistance is used by configuring a register. This
function is enabled in single-chip mode.
AD14 I/O pin for the external address/data bus.
This function is enabled when the external bus is enabled.
MB90860E Series
DS07-13748-5E 15
(Continued)
*1 : FPT-100P-M06
*2 : FPT-100P-M20
*3 : Refer to “■ I/O CIRCUIT TYPE” for details on the I/O circuit types.
Pin No.
Pin name
I/O
Circuit
type*3
Function
QFP100*1LQFP100*2
96 94
P17
G
General-purpose I/O pin. It is possible to select wheth-
er or not a pull-up resistance is used by configuring a
register. This function is enabled in single-chip mode.
AD15 I/O pin for the external address/data bus. This function
is enabled when the external bus is enabled.
97 to 100 95 to 98
P20 to P23
G
General-purpose I/O pins. It is possible to select
whether or not a pull-up resistance is used by
configuring a register. In external bus mode, each pin
is enabled as a general-purpose I/O port when the
corresponding bit in the external address output control
register (HACR) is 1.
A16 to A19
Output pins of the external address bus. When the
corresponding bit in the external address output control
register (HACR) is 0, the pins are enabled as high
address output pins (A16 to A19).
PPG9, B, D, F PPG output pins.
MB90860E Series
16 DS07-13748-5E
■I/O CIRCUIT TYPE
(Continued)
Type Circuit Remarks
AOscillator circuit
High-speed oscillator feedback
resistance = approx. 1 MΩ
B
Oscillator circuit
Low-speed oscillator feedback
resistance = approx. 10 MΩ
C • Mask ROM and evaluation device:
CMOS hysteresis input pin
• Flash memory device:
CMOS input pin
D • Mask ROM and evaluation device:
CMOS hysteresis input pin
Pull-down resistor value: approx. 50 kΩ
• Flash memory device:
CMOS input pin
No pull-down
E CMOS hysteresis input pin
Pull-up resistor value: approx. 50 kΩ
Standby control signal
X1
X0
Xout
Standby control signal
X1A
X0A
Xout
CMOS
hysteresis
input
R
Pull-down
resistor
CMOS
hysteresis
input
R
Pull-up
resistor
CMOS
hysteresis
input
R
MB90860E Series
DS07-13748-5E 17
(Continued)
Type Circuit Remarks
F • CMOS level output (IOL = 4 mA, IOH = −4 mA)
• CMOS hysteresis input (with input shut-
down in standby mode)
• Automotive input (with input shutdown in
standby mode)
G • CMOS level output (IOL = 4 mA, IOH = −4 mA)
• CMOS hysteresis input (with input shut-
down in standby mode)
• Automotive input (with input shutdown in
standby mode)
• TTL input (with input shutdown in standby
mode)
• Programmable pull-up resistor: 50 kΩ
approx.
H • CMOS level output (IOL = 3 mA, IOH = −3 mA)
• CMOS hysteresis input (with input shut-
down in standby mode)
• Automotive input (with input shutdown in
standby mode)
CMOS
hysteresis input
Automotive input
Standby control for
input shutdown
Pout
Nout
R
P-ch
N-ch
Pull-up control
CMOS
hysteresis input
Automotive input
TTL input
Standby control for
input shutdown
Pout
Nout
R
N-ch
P-ch
P-ch
CMOS
hysteresis input
Automotive input
Standby control for
input shutdown
Pout
Nout
R
P-ch
N-ch
MB90860E Series
18 DS07-13748-5E
(Continued)
Type Circuit Remarks
I • CMOS level output (IOL = 4 mA, IOH = −4 mA)
• CMOS hysteresis input (with input shut-
down in standby mode)
• Automotive input (with input shutdown in
standby mode)
• A/D converter analog input
J • CMOS level output (IOL = 4 mA, IOH = −4 mA)
• D/A analog output
• CMOS hysteresis input (with input shut-
down in standby mode)
• Automotive input (with input shutdown in
standby mode)
• A/D converter analog input
K Power supply input protection circuit
L • A/D converter reference voltage power
supply input pin with protection circuit
• Flash devices do not have a protection
circuit against VCC for pin AVRH
CMOS
hysteresis input
Automotive input
Standby control for
input shutdown
Analog input
Pout
Nout
R
N-ch
P-ch
Pout
Nout
R
P-ch
N-ch
CMOS
hysteresis input
Automotive input
Standby control for
input shutdown
Analog input
Analog output
P-ch
N-ch
ANE
AVR
ANE
P-ch
N-ch
MB90860E Series
DS07-13748-5E 19
(Continued)
Type Circuit Remarks
M • CMOS level output (IOL = 4 mA, IOH = −4 mA)
• CMOS input (with input shutdown in stand-
by mode)
• Automotive input (with input shutdown in
standby mode)
N • CMOS level output (IOL = 4 mA, IOH = −4 mA)
• CMOS input (with input shutdown in stand-
by mode)
• Automotive input (with input shutdown in
standby mode)
• TTL input (with input shutdown in standby
mode)
Programmable pull-up registor:50 kΩ
approx
O • CMOS level output(IOL = 4 mA, IOH = −4 mA)
• CMOS input (with input shutdown in stand-
by mode)
• Automotive input (with input shutdown in
standby mode)
• A/D converter analog input
CMOS input
Automotive input
Standby control for
input shutdown
Pout
Nout
R
P-ch
N-ch
Pull-up control
CMOS input
Automotive input
TTL input
Standby control for
input shutdown
Pout
Nout
R
P-ch
N-ch
P-ch
CMOS input
Automotive input
Standby control for
input shutdown
Analog input
Pout
Nout
R
P-ch
N-ch
MB90860E Series
20 DS07-13748-5E
■HANDLING DEVICES
1. Preventing latch-up
Latch-up may occur in a CMOS IC under the following conditions :
• A voltage higher than VCC or lower than VSS is applied to an input or output pin.
• A voltage higher than the rated voltage is applied between VCC and VSS pins.
• The AVCC power supply is applied before the VCC voltage.
Latch-up may increase the power supply current drastically, causing thermal damage to the device.
Therefore, be very careful not to apply analog power-supply voltages in excess of the digital power-supply
voltages.
2. Handling unused pins
Leaving unused input pins open may cause malfunctions or permanent damages. Unused input pins must
therefore be connected to a pull-up or pull-down resistor, with a resistance of 2 kΩ or more.
Unused bidirectional pins should be set to the output state and can then be left open, or set to the input state
and handled as described above.
3. Power supply pins (VCC/VSS)
• If there are multiple VCC and VSS pins, from the point of view of device design, pins to be of the same potential
are connected the inside of the device to prevent such malfunctioning as latch up.
To reduce unnecessary radiation, prevent malfunctioning of the strobe signal due to the rise of ground level,
and observe the standard for total output current, be sure to connect the VCC and VSS pins to the power
supply and ground externally. Connect VCC and VSS pins to the device from the current supply source at a
low impedance.
• As a measure against power supply noise, connect a capacitor of about 0.1 µF as a bypass capacitor between
VCC and VSS pins in the vicinity of VCC and VSS pins of the device.
4. Mode pins (MD0 to MD2)
Connect the mode pins directly to the VCC or VSS pins. To prevent the device unintentionally entering test mode
due to noise, lay out the printed circuit board so as to minimize the distance from the mode pins to VCC or VSS
pins and to provide a low-impedance connection.
Vcc
Vss
Vss
Vcc
Vss
Vcc
MB90860E
Series
Vcc Vss
Vcc
Vss
MB90860E Series
DS07-13748-5E 21
5. Sequence for turning on the A/D converter power supply and analog inputs
Make sure to turn on the A/D converter power supply (AVCC, AVRH, AVRL) and analog inputs (AN0 to AN23)
after turning on the digital power supply (VCC) .
Turn off the digital power after turning off the A/D converter power supply and analog inputs. In this case, make
sure that the voltage does not exceed AVRH or AVCC (turning on/off the analog and digital power supplies
simultaneously is acceptable) .
6. Handling A/D converter pins when the A/D converter is not used
When the A/D converter is not used, connect the pins such that AVCC = VCC, AVSS = AVRH = AVRL = VSS.
7. Crystal oscillator circuit
Noise near the X0, X1, X0A, and X1A pins can cause the device to malfunction. Design the printed circuit board
such that the crystal oscillators (or ceramic oscillators) are as close to the X0 and X1 pins, and X0A and X1A
pins as possible, and that the bypass capacitor to ground is as close to the device as possible. Furthermore, try
as much as possible to prevent the wiring for these components from crossing over the wiring of other circuitry.
It is highly recommended that the printed circuit board artwork is designed such that the X0, X1 pins and X0A,
X1A pins are surrounded by ground plane, as this is expected to produce more stable operation.
Please request the oscillator manufacturer to evaluate the oscillational characteristics of the crystal and this
device.
8. Pull-up/down resistors
The MB90860E series does not support internal pull-up/down resistors (however, port 0 to port 3 have built-in
pull-up resistors). Use external components where needed.
9. Using external clock
To use an external clock, drive the X0 pin and leave the X1 pin open.
10. Precautions when not using a sub clock signal
If you do not connect pins X0A and X1A to an oscillator, connect the X0A pin to a pull-down resistance and leave
the X1A pin open.
11. Precautions when operating in PLL clock mode
In the MB90860E series, if the oscillator is disconnected or the clock input is stopped while operating in PLL
mode, the microcontroller may continue to operate at the free-running frequency of the self-oscillating circuit
contained in the PLL. However, operation under these circumstances is not guaranteed.
12. Precautions when turning the power on
To prevent the internal regulator circuit from malfunctioning, ensure that the time over which the voltage rises
when the power is turned on is 50 or more µs (0.2 V to 2.7 V)
X0
X1
MB90860E Series
Open
MB90860E Series
22 DS07-13748-5E
13. Stabilization of power supply voltage
A sudden change in the supply voltage may cause the device to malfunction even within the specified VCC supply
voltage operating range. Therefore, the VCC supply voltage should be stabilized.
As a reference, stabilize the supply voltage by meeting the following standards.
•V
CC ripple variations (peak-to-peak value) at commercial frequencies (50 Hz/60 Hz) fall below 10% of the
standard VCC supply voltage
• The coefficient of fluctuation does not exceed 0.1 V/ms at instantaneous power switching.
14. Initialization
The device has internal registers that are only initialized by a power-on reset only. To initialize these registers,
turn on the power again.
15. Port 0 to port 3 output during power-on (external bus mode)
In external bus mode, the outputs of Port 0 to Port 3 may be indeterminate regardless of the reset input.
16. Flash security function
The security bit is located in the flash memory area. If protection code 01H is written to the security bit, the
security function is applied to the flash memory.
Therefore do not write 01H to this address if you do not use the security function.
Please refer to following table for the address of the security bit.
17. Serial communication
There is a possibility to receive wrong data due to the noise or other causes on the serial communication.
Therefore, design a printed circuit board so as to avoid noise.
Retransmit the data if an error occurs because of applying the checksum to the last data in consideration of
receiving wrong data due to the noise.
Flash memory size Address of security bit
MB90F867E(S) Embedded 1 Mbit Flash Memory FE0001H
Port 0 to Port 3 outputs
might be indeterminate
Port 0 to Port 3 outputs = Hi-Z
Port 0 to Port 3
VCC
1/2VCC
MB90860E Series
DS07-13748-5E 23
■BLOCK DIAGRAMS
• MB90V340E-101/102
RAM
LIN-UART
Prescaler
8/10-bit
24 channels
16-bit Reload
Timer
Clock
Controller
Input
Capture
8 channels
Output
Compare
8 channels
CAN
Controller
External
Interrupt
16LX
CPU
F2MC-16 Bus
X0,X1
RST
SOT4 to SOT0
SCK4 to SCK0
SIN4 to SIN0
AVCC
AVSS
AN23 to AN0
AVRH
AVRL
ADTG
TIN3 to TIN0
TOT3 to TOT0
IN7 to IN0
OUT7 to OUT0
RX2 to RX0
TX2 to TX0
INT15 to INT8
External
Bus
Interface
AD15 to AD00
A23 to A16
ALE
RD
WR/WRL
WRH
HRQ
HAK
RDY
CLK
X0A,X1A*
5 channels
10-bit
DAC
2 channels
DA01, DA00
FRCK0
FRCK1
PPGF to PPG0
I2C
Interface
SDA1, SDA0
SCL1, SCL0
3 channels
5 channels
2 channels
DMAC
* : Only in the MB90V340E-102
Clock
Monitor CKOT
(INT15R to INT8R)
INT7 to INT0
ADC
16 channels
30 Kbytes
4 channels
Free run
Timer 0
Free run
Timer 1
8/16-bit
PPG
16/8 channels
MB90860E Series
24 DS07-13748-5E
• MB90867E(S), MB90F867E(S)
RAM
ROM/Flash
LIN-UART
Prescaler
8/10-bit
24 channels
16-bit Reload
Timer
Clock
Controller
Input
Capture
8 channels
Output
Compare
8 channels
External
Interrupt
16LX
CPU
F2MC-16 Bus
X0,X1
RST
SOT3 to SOT0
SCK3 to SCK0
SIN3 to SIN0
AVCC
AVSS
AVRH
AVRL
ADTG
TIN3 to TIN0
TOT3 to TOT0
IN7 to IN0
OUT7 to OUT0
INT15 to INT8
External
Bus
Interface
AD15 to AD00
A23 to A16
ALE
RD
WR/WRL
WRH
HRQ
HAK
RDY
CLK
X0A,X1A*
128 Kbytes
4 channels
FRCK0
FRCK1
PPGF to PPG0
4 channels
I2C
Interface
SDA1, SDA0
SCL1, SCL0
2 channels
AN23 to AN0
6 Kbytes
DMAC
* : Only for devices without an 'S' suffix in the part number
Clock
Monitor CKOT
(INT15R to INT8R)
INT7 to INT0
ADC
16 channels
4 channels
Free run
Timer 1
Free run
Timer 0
8/16-bit
PPG
16/8 channels
MB90860E Series
DS07-13748-5E 25
■MEMORY MAP
Note : An image of the FF bank ROM data is visible in the upper part of bank 00. This makes it possible to use the
C compiler small memory model. Because the lower 16 bits of addresses in the 00 bank and the FF bank
are the same, tables in ROM can be referenced without using the far specifier in the pointer declarations.
For example, an attempt to access 00C000H accesses the value at FFC000H in ROM.
The ROM area in bank FF exceeds 32 Kbytes, and therefore, the entire image is not visible in bank 00.
The image between FF8000H and FFFFFFH is visible in bank 00, while the image between FF0000H and
FF7FFFH is visible only in bank FF.
MB90V340E-101/102
FFFFFF
H
FF0000
H
FEFFFF
H
FE0000
H
FDFFFF
H
FD0000
H
FCFFFF
H
FC0000
H
FBFFFF
H
FB0000
H
FAFFFF
H
FA0000
H
F9FFFF
H
F90000
H
F8FFFF
H
F80000
H
00FFFF
H
008000
H
007FFF
H
007900
H
0078FF
H
000100
H
0000EF
H
000000
H
ROM (FF bank)
ROM (FE bank)
ROM (FD bank)
ROM (FC bank)
ROM (FB bank)
ROM (FA bank)
ROM (F9 bank)
ROM (F8 bank)
ROM
(image of FF bank)
Peripherals
RAM 30 Kbytes
Peripherals
External access area
: No access
MB90867E(S)
MB90F867E(S)
FFFFFF
H
FF0000
H
FEFFFF
H
FE0000
H
0000EF
H
000000
H
00FFFF
H
007FFF
H
007900
H
0018FF
H
000100
H
008000
H
External
access area
ROM (image
of FF bank)
Peripherals
RAM 6 Kbytes
External access area
Peripherals
ROM (FF bank)
ROM (FE bank)
External access area
MB90860E Series
26 DS07-13748-5E
■I/O MAP
(Continued)
Address Register Abbrevia-
tion Access Resource name Initial value
000000HPort 0 Data Register PDR0 R/W Port 0 XXXXXXXXB
000001HPort 1 Data Register PDR1 R/W Port 1 XXXXXXXXB
000002HPort 2 Data Register PDR2 R/W Port 2 XXXXXXXXB
000003HPort 3 Data Register PDR3 R/W Port 3 XXXXXXXXB
000004HPort 4 Data Register PDR4 R/W Port 4 XXXXXXXXB
000005HPort 5 Data Register PDR5 R/W Port 5 XXXXXXXXB
000006HPort 6 Data Register PDR6 R/W Port 6 XXXXXXXXB
000007HPort 7 Data Register PDR7 R/W Port 7 XXXXXXXXB
000008HPort 8 Data Register PDR8 R/W Port 8 XXXXXXXXB
000009HPort 9 Data Register PDR9 R/W Port 9 XXXXXXXXB
00000AHPort A Data Register PDRA R/W Port A XXXXXXXXB
00000BHPort 5 Analog Input Enable Register ADER5 R/W Port 5, A/D 11111111B
00000CHPort 6 Analog Input Enable Register ADER6 R/W Port 6, A/D 11111111B
00000DHPort 7 Analog Input Enable Register ADER7 R/W Port 7, A/D 11111111B
00000EHInput Level Select Register 0 ILSR0 R/W Ports XXXXXXXXB
00000FHInput Level Select Register 1 ILSR1 R/W Ports XXXX0XXXB
000010HPort 0 Direction Register DDR0 R/W Port 0 00000000B
000011HPort 1 Direction Register DDR1 R/W Port 1 00000000B
000012HPort 2 Direction Register DDR2 R/W Port 2 00000000B
000013HPort 3 Direction Register DDR3 R/W Port 3 00000000B
000014HPort 4 Direction Register DDR4 R/W Port 4 00000000B
000015HPort 5 Direction Register DDR5 R/W Port 5 00000000B
000016HPort 6 Direction Register DDR6 R/W Port 6 00000000B
000017HPort 7 Direction Register DDR7 R/W Port 7 00000000B
000018HPort 8 Direction Register DDR8 R/W Port 8 00000000B
000019HPort 9 Direction Register DDR9 R/W Port 9 00000000B
00001AHPort A Direction Register DDRA R/W Port A 00000100B
00001BHReserved
00001CHPort 0 Pull-up Control Register PUCR0 R/W Port 0 00000000B
00001DHPort 1 Pull-up Control Register PUCR1 R/W Port 1 00000000B
00001EHPort 2 Pull-up Control Register PUCR2 R/W Port 2 00000000B
00001FHPort 3 Pull-up Control Register PUCR3 W, R/W Port 3 00000000B
MB90860E Series
DS07-13748-5E 27
(Continued)
Address Register Abbrevia-
tion Access Resource name Initial value
000020HSerial Mode Register 0 SMR0 W,R/W
UART0
00000000B
000021HSerial Control Register 0 SCR0 W,R/W 00000000B
000022HReceive/Transmit Data Register 0 RDR0/
TDR0 R/W 00000000B
000023HSerial Status Register 0 SSR0 R,R/W 00001000B
000024HExtended Communication Control
Register 0 ECCR0 R,W,
R/W 000000XXB
000025HExtended Status/Control Register 0 ESCR0 R/W 00000100B
000026HBaud Rate Generator Register 00 BGR00 R/W 00000000B
000027HBaud Rate Generator Register 01 BGR01 R/W 00000000B
000028HSerial Mode Register 1 SMR1 W,R/W
UART1
00000000B
000029HSerial Control Register 1 SCR1 W,R/W 00000000B
00002AHReceive/Transmit Data Register 1 RDR1/
TDR1 R/W 00000000B
00002BHSerial Status Register 1 SSR1 R,R/W 00001000B
00002CHExtended Communication Control
Register 1 ECCR1 R,W,
R/W 000000XXB
00002DHExtended Status/Control Register 1 ESCR1 R/W 00000100B
00002EHBaud Rate Generator Register 10 BGR10 R/W 00000000B
00002FHBaud Rate Generator Register 11 BGR11 R/W 00000000B
000030HPPG 0 Operation Mode Control Register PPGC0 W,R/W
16-bit PPG 0/1
0X000XX1B
000031HPPG 1 Operation Mode Control Register PPGC1 W,R/W 0X000001B
000032HPPG 0/PPG 1 Count Clock Select Register PPG01 R/W 000000X0B
000033HReserved
000034HPPG 2 Operation Mode Control Register PPGC2 W,R/W
16-bit PPG 2/3
0X000XX1B
000035HPPG 3 Operation Mode Control Register PPGC3 W,R/W 0X000001B
000036HPPG 2/PPG 3 Count Clock Select Register PPG23 R/W 000000X0B
000037HReserved
000038HPPG 4 Operation Mode Control Register PPGC4 W,R/W
16-bit PPG 4/5
0X000XX1B
000039HPPG 5 Operation Mode Control Register PPGC5 W,R/W 0X000001B
00003AHPPG 4/PPG 5 Clock Select Register PPG45 R/W 000000X0B
00003BHAddress Detect Control Register 1 PACSR1 R/W Address Match
Detection 1 00000000B
00003CHPPG 6 Operation Mode Control Register PPGC6 W,R/W
16-bit PPG 6/7
0X000XX1B
00003DHPPG 7 Operation Mode Control Register PPGC7 W,R/W 0X000001B
00003EHPPG 6/PPG 7 Count Clock Control Register PPG67 R/W 000000X0B
00003FHReserved
MB90860E Series
28 DS07-13748-5E
(Continued)
Address Register Abbrevia-
tion Access Resource name Initial value
000040HPPG 8 Operation Mode Control Register PPGC8 W,R/W
16-bit PPG 8/9
0X000XX1B
000041HPPG 9 Operation Mode Control Register PPGC9 W,R/W 0X000001B
000042HPPG 8/PPG 9 Count Clock Control
Register PPG89 R/W 000000X0B
000043HReserved
000044HPPG A Operation Mode Control Register PPGCA W,R/W
16-bit PPG A/B
0X000XX1B
000045HPPG B Operation Mode Control Register PPGCB W,R/W 0X000001B
000046HPPG A/PPG B Count Clock Select
Register PPGAB R/W 000000X0B
000047HReserved
000048HPPG C Operation Mode Control Register PPGCC W,R/W
16-bit PPG C/D
0X000XX1B
000049HPPG D Operation Mode Control Register PPGCD W,R/W 0X000001B
00004AHPPG C/PPG D Count Clock Select
Register PPGCD R/W 000000X0B
00004BHReserved
00004CHPPG E Operation Mode Control Register PPGCE W,R/W
16-bit PPG E/F
0X000XX1B
00004DHPPG F Operation Mode Control Register PPGCF W,R/W 0X000001B
00004EHPPG E/PPG F Count Clock Select
Register PPGEF R/W 000000X0B
00004FHReserved
000050HInput Capture Control Status 0/1 ICS01 R/W Input Capture 0/1 00000000B
000051HInput Capture Edge 0/1 ICE01 R/W, R XXX0X0XXB
000052HInput Capture Control Status 2/3 ICS23 R/W Input Capture 2/3 00000000B
000053HInput Capture Edge 2/3 ICE23 R XXXXXXXXB
000054HInput Capture Control Status 4/5 ICS45 R/W Input Capture 4/5 00000000B
000055HInput Capture Edge 4/5 ICE45 R XXXXXXXXB
000056HInput Capture Control Status 6/7 ICS67 R/W Input Capture 6/7 00000000B
000057HInput Capture Edge 6/7 ICE67 R/W, R XXX000XXB
000058HOutput Compare Control Status 0 OCS0 R/W Output Compare 0/1 0000XX00B
000059HOutput Compare Control Status 1 OCS1 R/W 0XX00000B
00005AHOutput Compare Control Status 2 OCS2 R/W Output Compare 2/3 0000XX00B
00005BHOutput Compare Control Status 3 OCS3 R/W 0XX00000B
00005CHOutput Compare Control Status 4 OCS4 R/W Output Compare 4/5 0000XX00B
00005DHOutput Compare Control Status 5 OCS5 R/W 0XX00000B
00005EHOutput Compare Control Status 6 OCS6 R/W Output Compare 6/7 0000XX00B
00005FHOutput Compare Control Status 7 OCS7 R/W 0XX00000B
MB90860E Series
DS07-13748-5E 29
(Continued)
Address Register Abbrevia-
tion Access Resource name Initial value
000060HTimer Control Status 0 TMCSR0 R/W 16-bit Reload
Timer 0
00000000B
000061HTimer Control Status 0 TMCSR0 R/W XXXX0000B
000062HTimer Control Status 1 TMCSR1 R/W 16-bit Reload
Timer 1
00000000B
000063HTimer Control Status 1 TMCSR1 R/W XXXX0000B
000064HTimer Control Status 2 TMCSR2 R/W 16-bit Reload
Timer 2
00000000B
000065HTimer Control Status 2 TMCSR2 R/W XXXX0000B
000066HTimer Control Status 3 TMCSR3 R/W 16-bit Reload
Timer 3
00000000B
000067HTimer Control Status 3 TMCSR3 R/W XXXX0000B
000068HA/D Control Status 0 ADCS0 R/W
A/D Converter
000XXXX0B
000069HA/D Control Status 1 ADCS1 R/W 0000000XB
00006AHA/D Data 0 ADCR0 R 00000000B
00006BHA/D Data 1 ADCR1 R XXXXXX00B
00006CHADC Setting 0 ADSR0 R/W 00000000B
00006DHADC Setting 1 ADSR1 R/W 00000000B
00006EHReserved
00006FHROM Mirror Function Select ROMM W ROM Mirror XXXXXXX1B
000070H
to
00009AH
Reserved
00009BHDMA Descriptor Channel Selection
Register DCSR R/W
DMA
00000000B
00009CHDMA Status L Register DSRL R/W 00000000B
00009DHDMA Status H Register DSRH R/W 00000000B
00009EHAddress Detect Control Register 0 PACSR0 R/W Address Match
Detection 0 00000000B
00009FHDelayed Interrupt Source Generate/
Release Register DIRR R/W Delayed Interrupt XXXXXXX0B
0000A0HLow-power Mode Control Register LPMCR W,R/W Low Power
Control Circuit 00011000B
0000A1HClock Selection Register CKSCR R,R/W Low Power
Control Circuit 11111100B
0000A2H,
0000A3HReserved
0000A4HDMA Stop Status Register DSSR R/W DMA 00000000B
0000A5HAutomatic Ready Function Select Register ARSR W
External Memory
Access
0011XX00B
0000A6HExternal Address Output Control Register HACR W 00000000B
0000A7HBus Control Signal Selection Register ECSR W 0000000XB
MB90860E Series
30 DS07-13748-5E
(Continued)
Address Register Abbrevia-
tion Access Resource name Initial value
0000A8HWatchdog Control Register WDTC R,W Watchdog Timer XXXXX111B
0000A9HTime Base Timer Control Register TBTC W,R/W Time Base Timer 1XX00100B
0000AAHWatch Timer Control Register WTC R,R/W Watch Timer 1X001000B
0000ABHReserved
0000ACHDMA Enable L Register DERL R/W DMA 00000000B
0000ADHDMA Enable H Register DERH R/W 00000000B
0000AEH
Flash Control Status Register
(Flash Devices only.
Otherwise reserved)
FMCS R,R/W Flash Memory 000X0000B
0000AFHReserved
0000B0HInterrupt Control Register 00 ICR00 W,R/W
Interrupt Control
00000111B
0000B1HInterrupt Control Register 01 ICR01 W,R/W 00000111B
0000B2HInterrupt Control Register 02 ICR02 W,R/W 00000111B
0000B3HInterrupt Control Register 03 ICR03 W,R/W 00000111B
0000B4HInterrupt Control Register 04 ICR04 W,R/W 00000111B
0000B5HInterrupt Control Register 05 ICR05 W,R/W 00000111B
0000B6HInterrupt Control Register 06 ICR06 W,R/W 00000111B
0000B7HInterrupt Control Register 07 ICR07 W,R/W 00000111B
0000B8HInterrupt Control Register 08 ICR08 W,R/W 00000111B
0000B9HInterrupt Control Register 09 ICR09 W,R/W 00000111B
0000BAHInterrupt Control Register 10 ICR10 W,R/W 00000111B
0000BBHInterrupt Control Register 11 ICR11 W,R/W 00000111B
0000BCHInterrupt Control Register 12 ICR12 W,R/W 00000111B
0000BDHInterrupt Control Register 13 ICR13 W,R/W 00000111B
0000BEHInterrupt Control Register 14 ICR14 W,R/W 00000111B
0000BFHInterrupt Control Register 15 ICR15 W,R/W 00000111B
0000C0HD/A Converter Data 0 Register DAT0 R/W
D/A Converter
XXXXXXXXB
0000C1HD/A Converter Data 1 Register DAT1 R/W XXXXXXXXB
0000C2HD/A Control 0 Register DACR0 R/W XXXXXXX0B
0000C3HD/A Control 1 Register DACR1 R/W XXXXXXX0B
0000C4H,
0000C5HReserved
0000C6HExternal Interrupt Enable 0 ENIR0 R/W
External Interrupt 0
00000000B
0000C7HExternal Interrupt Source 0 EIRR0 R/W XXXXXXXXB
0000C8HExternal Interrupt Level Setting 0 ELVR0 R/W 00000000B
0000C9HExternal Interrupt Level Setting 0 ELVR0 R/W 00000000B
MB90860E Series
DS07-13748-5E 31
(Continued)
Address Register Abbrevia-
tion Access Resource name Initial value
0000CAHExternal Interrupt Enable 1 ENIR1 R/W
External Interrupt 1
00000000B
0000CBHExternal Interrupt Source 1 EIRR1 R/W XXXXXXXXB
0000CCHExternal Interrupt Level Setting 1 ELVR1 R/W 00000000B
0000CDHExternal Interrupt Level Setting 1 ELVR1 R/W 00000000B
0000CEHExternal Interrupt Source Select EISSR R/W 00000000B
0000CFHPLL/Sub Clock Control Register PSCCR W PLL XXXX0000B
0000D0HDMA Buffer Address Pointer L Register BAPL R/W
DMA
XXXXXXXXB
0000D1HDMA Buffer Address Pointer M Register BAPM R/W XXXXXXXXB
0000D2HDMA Buffer Address Pointer H Register BAPH R/W XXXXXXXXB
0000D3HDMA Control Register DMACS R/W XXXXXXXXB
0000D4HI/O Register Address Pointer L
Register IOAL R/W XXXXXXXXB
0000D5HI/O Register Address Pointer H
Register IOAH R/W XXXXXXXXB
0000D6HData Counter L Register DCTL R/W XXXXXXXXB
0000D7HData Counter H Register DCTH R/W XXXXXXXXB
0000D8HSerial Mode Register 2 SMR2 W,R/W
UART2
00000000B
0000D9HSerial Control Register 2 SCR2 W,R/W 00000000B
0000DAHReceive/Transmit Data Register 2 RDR2/
TDR2 R/W 00000000B
0000DBHSerial Status Register 2 SSR2 R,R/W 00001000B
0000DCHExtended Communication Control
Register 2 ECCR2 R,W,
R/W 000000XXB
0000DDHExtended Status Control Register 2 ESCR2 R/W 00000100B
0000DEHBaud Rate Generator Register 20 BGR20 R/W 00000000B
0000DFHBaud Rate Generator Register 21 BGR21 R/W 00000000B
0000E0H
to
0000FFH
External area
007900HReload Register L0 PRLL0 R/W
16-bit PPG 0/1
XXXXXXXXB
007901HReload Register H0 PRLH0 R/W XXXXXXXXB
007902HReload Register L1 PRLL1 R/W XXXXXXXXB
007903HReload Register H1 PRLH1 R/W XXXXXXXXB
007904HReload Register L2 PRLL2 R/W
16-bit PPG 2/3
XXXXXXXXB
007905HReload Register H2 PRLH2 R/W XXXXXXXXB
007906HReload Register L3 PRLL3 R/W XXXXXXXXB
007907HReload Register H3 PRLH3 R/W XXXXXXXXB
MB90860E Series
32 DS07-13748-5E
(Continued)
Address Register Abbrevia-
tion Access Resource name Initial value
007908HReload Register L4 PRLL4 R/W
16-bit PPG 4/5
XXXXXXXXB
007909HReload Register H4 PRLH4 R/W XXXXXXXXB
00790AHReload Register L5 PRLL5 R/W XXXXXXXXB
00790BHReload Register H5 PRLH5 R/W XXXXXXXXB
00790CHReload Register L6 PRLL6 R/W
16-bit PPG 6/7
XXXXXXXXB
00790DHReload Register H6 PRLH6 R/W XXXXXXXXB
00790EHReload Register L7 PRLL7 R/W XXXXXXXXB
00790FHReload Register H7 PRLH7 R/W XXXXXXXXB
007910HReload Register L8 PRLL8 R/W
16-bit PPG 8/9
XXXXXXXXB
007911HReload Register H8 PRLH8 R/W XXXXXXXXB
007912HReload Register L9 PRLL9 R/W XXXXXXXXB
007913HReload Register H9 PRLH9 R/W XXXXXXXXB
007914HReload Register LA PRLLA R/W
16-bit PPG A/B
XXXXXXXXB
007915HReload Register HA PRLHA R/W XXXXXXXXB
007916HReload Register LB PRLLB R/W XXXXXXXXB
007917HReload Register HB PRLHB R/W XXXXXXXXB
007918HReload Register LC PRLLC R/W
16-bit PPG C/D
XXXXXXXXB
007919HReload Register HC PRLHC R/W XXXXXXXXB
00791AHReload Register LD PRLLD R/W XXXXXXXXB
00791BHReload Register HD PRLHD R/W XXXXXXXXB
00791CHReload Register LE PRLLE R/W
16-bit PPG E/F
XXXXXXXXB
00791DHReload Register HE PRLHE R/W XXXXXXXXB
00791EHReload Register LF PRLLF R/W XXXXXXXXB
00791FHReload Register HF PRLHF R/W XXXXXXXXB
007920HInput Capture 0 IPCP0 R
Input Capture 0/1
XXXXXXXXB
007921HInput Capture 0 IPCP0 R XXXXXXXXB
007922HInput Capture 1 IPCP1 R XXXXXXXXB
007923HInput Capture 1 IPCP1 R XXXXXXXXB
007924HInput Capture 2 IPCP2 R
Input Capture 2/3
XXXXXXXXB
007925HInput Capture 2 IPCP2 R XXXXXXXXB
007926HInput Capture 3 IPCP3 R XXXXXXXXB
007927HInput Capture 3 IPCP3 R XXXXXXXXB
007928HInput Capture 4 IPCP4 R
Input Capture 4/5
XXXXXXXXB
007929HInput Capture 4 IPCP4 R XXXXXXXXB
00792AHInput Capture 5 IPCP5 R XXXXXXXXB
00792BHInput Capture 5 IPCP5 R XXXXXXXXB
MB90860E Series
DS07-13748-5E 33
(Continued)
Address Register Abbrevia-
tion Access Resource name Initial value
00792CHInput Capture 6 IPCP6 R
Input Capture 6/7
XXXXXXXXB
00792DHInput Capture 6 IPCP6 R XXXXXXXXB
00792EHInput Capture 7 IPCP7 R XXXXXXXXB
00792FHInput Capture 7 IPCP7 R XXXXXXXXB
007930HOutput Compare 0 OCCP0 R/W
Output Compare 0/1
XXXXXXXXB
007931HOutput Compare 0 OCCP0 R/W XXXXXXXXB
007932HOutput Compare 1 OCCP1 R/W XXXXXXXXB
007933HOutput Compare 1 OCCP1 R/W XXXXXXXXB
007934HOutput Compare 2 OCCP2 R/W
Output Compare 2/3
XXXXXXXXB
007935HOutput Compare 2 OCCP2 R/W XXXXXXXXB
007936HOutput Compare 3 OCCP3 R/W XXXXXXXXB
007937HOutput Compare 3 OCCP3 R/W XXXXXXXXB
007938HOutput Compare 4 OCCP4 R/W
Output Compare 4/5
XXXXXXXXB
007939HOutput Compare 4 OCCP4 R/W XXXXXXXXB
00793AHOutput Compare 5 OCCP5 R/W XXXXXXXXB
00793BHOutput Compare 5 OCCP5 R/W XXXXXXXXB
00793CHOutput Compare 6 OCCP6 R/W
Output Compare 6/7
XXXXXXXXB
00793DHOutput Compare 6 OCCP6 R/W XXXXXXXXB
00793EHOutput Compare 7 OCCP7 R/W XXXXXXXXB
00793FHOutput Compare 7 OCCP7 R/W XXXXXXXXB
007940HTimer Data 0 TCDT0 R/W
Free-run Timer 0
00000000B
007941HTimer Data 0 TCDT0 R/W 00000000B
007942HTimer Control Status 0 TCCSL0 R/W 00000000B
007943HTimer Control Status 0 TCCSH0 R/W 0XXXXXXXB
007944HTimer Data 1 TCDT1 R/W
Free-run Timer 1
00000000B
007945HTimer Data 1 TCDT1 R/W 00000000B
007946HTimer Control Status 1 TCCSL1 R/W 00000000B
007947HTimer Control Status 1 TCCSH1 R/W 0XXXXXXXB
007948HTimer 0/Reload 0 TMR0/
TMRLR0
R/W 16-bit Reload
Timer 0
XXXXXXXXB
007949HR/W XXXXXXXXB
00794AHTimer 1/Reload 1 TMR1/
TMRLR1
R/W 16-bit Reload
Timer 1
XXXXXXXXB
00794BHR/W XXXXXXXXB
00794CHTimer 2/Reload 2 TMR2/
TMRLR2
R/W 16-bit Reload
Timer 2
XXXXXXXXB
00794DHR/W XXXXXXXXB
00794EHTimer 3/Reload 3 TMR3/
TMRLR3
R/W 16-bit Reload
Timer 3
XXXXXXXXB
00794FHR/W XXXXXXXXB
MB90860E Series
34 DS07-13748-5E
(Continued)
Address Register Abbrevia-
tion Access Resource name Initial value
007950HSerial Mode Register 3 SMR3 W,R/W
UART3
00000000B
007951HSerial Control Register 3 SCR3 W,R/W 00000000B
007952HReceive/Transmit Data Register 3 RDR3/
TDR3 R/W 00000000B
007953HSerial Status Register 3 SSR3 R,R/W 00001000B
007954HExtended Communication Control
Register 3 ECCR3 R,W,
R/W 000000XXB
007955HExtended Status Control Register ESCR3 R/W 00000100B
007956HBaud Rate Generator Register 30 BGR30 R/W 00000000B
007957HBaud Rate Generator Register 31 BGR31 R/W 00000000B
007958HSerial Mode Register 4 SMR4 W,R/W
UART4
00000000B
007959HSerial Control Register 4 SCR4 W,R/W 00000000B
00795AHReceive/Transmit Data Register 4 RDR4/
TDR4 R/W 00000000B
00795BHSerial Status Register 4 SSR4 R,R/W 00001000B
00795CHExtended Communication Control
Register 4 ECCR4 R,W,
R/W 000000XXB
00795DHExtended Status Control Register ESCR4 R/W 00000100B
00795EHBaud Rate Generator Register 40 BGR40 R/W 00000000B
00795FHBaud Rate Generator Register 41 BGR41 R/W 00000000B
007960H
to
00796BH
Reserved
00796CHClock Output Enable Register CLKR R/W Clock Monitor XXXX0000B
00796DH
to
00796FH
Reserved
007970HI2C Bus Status Register 0 IBSR0 R
I2C Interface 0
00000000B
007971HI2C bus Control Register 0 IBCR0 W,R/W 00000000B
007972HI2C 10-bit Slave Address Register 0 ITBAL0 R/W 00000000B
007973HITBAH0 R/W 00000000B
007974HI2C 10-bit Slave Address Mask
Register 0
ITMKL0 R/W 11111111B
007975HITMKH0 R/W 00111111B
007976HI2C 7-bit Slave Address Register 0 ISBA0 R/W 00000000B
007977HI2C 7-bit Slave Address Mask Register 0 ISMK0 R/W 01111111B
007978HI2C Data Register 0 IDAR0 R/W 00000000B
007979H,
00797AHReserved
MB90860E Series
DS07-13748-5E 35
(Continued)
Address Register Abbrevia-
tion Access Resource name Initial value
00797BHI2C Clock Control Register 0 ICCR0 R/W I2C Interface 0 00011111B
00797CH
to
00797FH
Reserved
007980HI2C Bus Status Register 1 IBSR1 R
I2C Interface 1
00000000B
007981HI2C Bus Control Register 1 IBCR1 W,R/W 00000000B
007982HI2C 10-bit Slave Address Register 1 ITBAL1 R/W 00000000B
007983HITBAH1 R/W 00000000B
007984HI2C 10-bit Slave Address Mask
Register 1
ITMKL1 R/W 11111111B
007985HITMKH1 R/W 00111111B
007986HI2C 7-bit Slave Address Register 1 ISBA1 R/W 00000000B
007987HI2C 7-bit Slave Address Mask Register 1 ISMK1 R/W 01111111B
007988HI2C Data Register 1 IDAR1 R/W 00000000B
007989H,
00798AHReserved
00798BHI2C Clock Control Register 1 ICCR1 R/W I2C Interface 1 00011111B
00798CH
to
0079C1H
Reserved
0079C2HClock Modulator Control Register CMCR R, R/W Clock Modulator 0001X000B
0079C3H
to
0079DFH
Reserved
0079E0HDetect Address Setting 0 PADR0 R/W
Address Match
Detection 0
XXXXXXXXB
0079E1HDetect Address Setting 0 PADR0 R/W XXXXXXXXB
0079E2HDetect Address Setting 0 PADR0 R/W XXXXXXXXB
0079E3HDetect Address Setting 1 PADR1 R/W XXXXXXXXB
0079E4HDetect Address Setting 1 PADR1 R/W XXXXXXXXB
0079E5HDetect Address Setting 1 PADR1 R/W XXXXXXXXB
0079E6HDetect Address Setting 2 PADR2 R/W XXXXXXXXB
0079E7HDetect Address Setting 2 PADR2 R/W XXXXXXXXB
0079E8HDetect Address Setting 2 PADR2 R/W XXXXXXXXB
0079E9H
to
0079EFH
Reserved
MB90860E Series
36 DS07-13748-5E
(Continued)
Notes : • Initial value of “X” represents undefined value.
• Do not write to the reserved areas in the I/O map. Reading from reserved addresses will return undefined
values.
Address Register Abbrevia-
tion Access Resource name Initial value
0079F0HDetect Address Setting 3 PADR3 R/W
Address Match
Detection 1
XXXXXXXXB
0079F1HDetect Address Setting 3 PADR3 R/W XXXXXXXXB
0079F2HDetect Address Setting 3 PADR3 R/W XXXXXXXXB
0079F3HDetect Address Setting 4 PADR4 R/W XXXXXXXXB
0079F4HDetect Address Setting 4 PADR4 R/W XXXXXXXXB
0079F5HDetect Address Setting 4 PADR4 R/W XXXXXXXXB
0079F6HDetect Address Setting 5 PADR5 R/W XXXXXXXXB
0079F7HDetect Address Setting 5 PADR5 R/W XXXXXXXXB
0079F8HDetect Address Setting 5 PADR5 R/W XXXXXXXXB
0079F9H
to
007FFFH
Reserved
MB90860E Series
DS07-13748-5E 37
■INTERRUPT SOURCES, INTERRUPT VECTORS, INTERRUPT CONTROL REGISTER
(Continued)
Interrupt source EI2OS
clear
DMA ch
number
Interrupt vector Interrupt control
register
Number Address Number Address
Reset N ⎯#08 FFFFDCH⎯⎯
INT9 instruction N ⎯#09 FFFFD8H⎯⎯
Exception N ⎯#10 FFFFD4H⎯⎯
(Reserved) N ⎯#11 FFFFD0HICR00 0000B0H
(Reserved) N ⎯#12 FFFFCCH
Input Capture 6 Y1 ⎯#13 FFFFC8HICR01 0000B1H
Input Capture 7 Y1 ⎯#14 FFFFC4H
I2C0 N ⎯#15 FFFFC0HICR02 0000B2H
(Reserved) N ⎯#16 FFFFBCH
16-bit Reload Timer 0 Y1 0 #17 FFFFB8HICR03 0000B3H
16-bit Reload Timer 1 Y1 1 #18 FFFFB4H
16-bit Reload Timer 2 Y1 2 #19 FFFFB0HICR04 0000B4H
16-bit Reload Timer 3 Y1 ⎯#20 FFFFACH
PPG 0/1/4/5 N ⎯#21 FFFFA8HICR05 0000B5H
PPG 2/3/6/7 N ⎯#22 FFFFA4H
PPG 8/9/C/D N ⎯#23 FFFFA0HICR06 0000B6H
PPG A/B/E/F N ⎯#24 FFFF9CH
Time Base Timer N ⎯#25 FFFF98HICR07 0000B7H
External Interrupt 0 to 3, 8 to 11 Y1 3 #26 FFFF94H
Watch Timer N ⎯#27 FFFF90HICR08 0000B8H
External Interrupt 4 to 7, 12 to 15 Y1 4 #28 FFFF8CH
8/10-bit A/D Converter Y1 5 #29 FFFF88HICR09 0000B9H
Free-run Timer 0, Free-run Timer 1 N ⎯#30 FFFF84H
Input Capture 4/5, I2C1 Y1 6 #31 FFFF80HICR10 0000BAH
Output Compare 0/1/4/5 Y1 7 #32 FFFF7CH
Input Capture 0 to 3 Y1 8 #33 FFFF78HICR11 0000BBH
Output Compare 2/3/6/7 Y1 9 #34 FFFF74H
UART 0 Reception Y2 10 #35 FFFF70HICR12 0000BCH
UART 0 Transmission Y1 11 #36 FFFF6CH
UART 1 Reception /
UART 3 Reception Y2 12 #37 FFFF68H
ICR13 0000BDH
UART 1 Transmission /
UART 3 Transmission Y1 13 #38 FFFF64H
MB90860E Series
38 DS07-13748-5E
(Continued)
Y1 : Usable
Y2 : Usable, with EI2OS stop function
N : Unusable
Notes : •Peripheral resources that share an ICR register have the same interrupt level.
•When two peripheral resources share an ICR register, only one can use Extended Intelligent I/O Service
at a time.
•When either of the two peripheral resources sharing an ICR register specifies Extended Intelligent I/O
Service, the other one cannot use interrupts.
Interrupt source EI2OS
clear
DMA ch
number
Interrupt vector Interrupt control
register
Number Address Number Address
UART 2 Reception /
UART 4 Reception Y2 14 #39 FFFF60H
ICR14 0000BEH
UART 2 Transmission /
UART 4 Transmission Y1 15 #40 FFFF5CH
Flash Memory N ⎯#41 FFFF58HICR15 0000BFH
Delayed interrupt N ⎯#42 FFFF54H
MB90860E Series
DS07-13748-5E 39
■ELECTRICAL CHARACTERISTICS
1. Absolute Maximum Ratings
*1 : This parameter is based on VSS = AVSS = 0 V.
*2 : Set AVCC and VCC to the same voltage. Make sure that AVCC does not exceed VCC and that the voltage at the
analog inputs does not exceed AVCC when the power is switched on.
*3 : VI and VO must not exceed VCC + 0.3 V. VI must not exceed the specified ratings. However if the maximum
current to/from an input is limited by some means using external components, the ICLAMP rating supersedes the
VI rating.
*4 : Applicable to pins : P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P60 to P67,
P70 to P77, P80 to P87, P90 to P97, PA0, and PA1
(Continued)
Parameter Symbol Rating Unit Remarks
Min Max
Power supply voltage*1
VCC VSS − 0.3 VSS + 6.0 V
AVCC VSS − 0.3 VSS + 6.0 V VCC = AVCC*2
AVRH,
AVRL VSS − 0.3 VSS + 6.0 V AVCC ≥ AVRH, AVCC ≥ AVRL,
AVRH ≥ AVRL
Input voltage*1VIVSS − 0.3 VSS + 6.0 V *3
Output voltage*1VOVSS − 0.3 VSS + 6.0 V *3
Maximum clamp current ICLAMP −4.0 +4.0 mA *5
Total maximum clamp current Σ|ICLAMP|⎯40 mA *5
“L” level maximum output current IOL ⎯15 mA *4
“L” level average output current IOLAV ⎯4mA*4
“L” level maximum overall output current ΣIOL ⎯100 mA *4
“L” level average overall output current ΣIOLAV ⎯50 mA *4
“H” level maximum output current IOH ⎯−15 mA *4
“H” level average output current IOHAV ⎯−4mA*4
“H” level maximum overall output current ΣIOH ⎯−100 mA *4
“H” level average overall output current ΣIOHAV ⎯−50 mA *4
Power consumption PD⎯340 mW
Operating temperature TA−40 +105 °C
Storage temperature TSTG −55 +150 °C
MB90860E Series
40 DS07-13748-5E
(Continued)
*5 : • Applicable to pins: P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47,
P50 to P57 (evaluation device : P50 to P55) , P60 to P67, P70 to P77, P80 to P87,
P90 to P97, PA0, and PA1
•Use within recommended operating conditions.
•Use at DC voltage (current)
•The +B signal should always be applied by placing a limiting resistance between the +B signal and the
microcontroller.
•The value of the limiting resistance should be set so that when the +B signal is applied the input current to
the microcontroller pin does not exceed the rated values, either instantaneously or for prolonged periods.
•Note that when the microcontroller drive current is low, such as in the power saving modes, the +B input
potential may pass through the protective diode and increase the potential at the VCC pin, and this may affect
other devices.
•Note that if a +B signal is input when the microcontroller power supply is off (not fixed at 0 V) , power may
be supplied through the +B pin, resulting in incomplete operation of the microcontroller.
•Note that if the +B input is applied during power-on, the power supplied via the +B pin may result in the
supply voltage being insufficient to activate the power-on reset.
•Care must be taken not to leave +B input pins open.
•Sample recommended circuits:
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
P-ch
N-ch
VCC
R
• Input/output equivalent circuits
+B input (0 V to 16 V)
Limiting
resistance
Protective diode
MB90860E Series
DS07-13748-5E 41
2. Recommended Operating Conditions
(VSS = AVSS = 0 V)
WARNING: The recommended operating conditions are required in order to ensure the normal operation of
the semiconductor device. All of the device's electrical characteristics are warranted when the
device is operated within these ranges.
Always use semiconductor devices within their recommended operating condition ranges.
Operation outside these ranges may adversely affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented
on the data sheet. Users considering application outside the listed conditions are advised to contact
their representatives beforehand.
Parameter Symbol Value Unit Remarks
Min Typ Max
Power supply voltage VCC,
AVCC
4.0 5.0 5.5 V During normal operation
3.5 5.0 5.5 V
During normal operation, when not
using the A/D converter and not
Flash programming.
4.5 5.0 5.5 V When using an external bus
3.0 ⎯5.5 V Maintains RAM data in stop mode
Smoothing capacitor CS0.1 ⎯1.0 µF
Use a ceramic capacitor or a
capacitor with similar AC
characteristics. The bypass
capacitor used on the VCC pin
should have a greater capacitance
than this capacitor.
Operating temperature TA−40 ⎯+105 °C
C
CS
• C Pin Connection Diagram
MB90860E Series
42 DS07-13748-5E
3. DC Characteristics
(TA = −40 °C to +105 °C, VCC = 5.0 V ± 10%, fCP ≤ 24 MHz, VSS = AVSS = 0 V)
(Continued)
Parameter Sym-
bol Pin Condition Value Unit Remarks
Min Typ Max
Input H
voltage
(At VCC =
5 V ± 10%)
VIHS ⎯⎯0.8 VCC ⎯VCC + 0.3 V
Port inputs if CMOS
hysteresis input levels
are selected (except
P12, P44, P45, P46,
P47, P50, P82, P85)
VIHA ⎯⎯0.8 VCC ⎯VCC + 0.3 V
Port inputs if
automotive input levels
are selected
VIHT ⎯⎯2.0 ⎯VCC + 0.3 V Port inputs if TTL input
levels are selected
VIHS ⎯⎯0.7 VCC ⎯VCC + 0.3 V
P12, P50, P82, P85
inputs if CMOS input
levels are selected
VIHI ⎯⎯0.7 VCC ⎯VCC + 0.3 V
P44, P45, P46, P47 in-
puts if CMOS hysteresis
input levels are selected
VIHR ⎯⎯0.8 VCC ⎯VCC + 0.3 V RST input pin (CMOS
hysteresis)
VIHM ⎯⎯VCC − 0.3 ⎯VCC + 0.3 V MD input pin
Input L
voltage
(At VCC =
5 V ± 10%)
VILS ⎯⎯VSS − 0.3 ⎯0.2 VCC V
Port inputs if CMOS
hysteresis input levels
are selected (except
P12, P44, P45, P46,
P47, P50, P82, P85)
VILA ⎯⎯VSS − 0.3 ⎯0.5 VCC V
Port inputs if
automotive input levels
are selected
VILT ⎯⎯VSS − 0.3 ⎯0.8 V Port inputs if TTL
input levels are selected
VILS ⎯⎯VSS − 0.3 ⎯0.3 VCC V
P12, P50, P82, P85
inputs if CMOS input
levels are selected
VILI ⎯⎯VSS − 0.3 ⎯0.3 VCC V
P44, P45, P46, P47 in-
puts if CMOS hysteresis
input levels are selected
VILR ⎯⎯VSS − 0.3 ⎯0.2 VCC VRST input pin (CMOS
hysteresis)
VILM ⎯⎯VSS − 0.3 ⎯VSS + 0.3 V MD input pin
Output H
voltage VOH Normal
outputs
VCC = 4.5 V,
IOH = −4.0 mA VCC − 0.5 ⎯⎯V
Output H
voltage VOHI I2C current
outputs
VCC = 4.5 V,
IOH = −3.0 mA VCC − 0.5 ⎯⎯V
Output L
voltage VOL Normal
outputs
VCC = 4.5 V,
IOL = 4.0 mA ⎯⎯0.4 V
Output L
voltage VOLI I2C current
outputs
VCC = 4.5 V,
IOL = 3.0 mA ⎯⎯0.4 V
MB90860E Series
DS07-13748-5E 43
(Continued)
(TA = −40 °C to +105 °C, VCC = 5.0 V ± 10%, fCP ≤ 24 MHz, VSS = AVSS = 0 V)
* : Power supply currents were measured under test conditions using an external clock.
Parameter Sym-
bol Pin Condition Value Unit Remarks
Min Typ Max
Input leak current IIL ⎯VCC = 5.5 V, VSS < VI < VCC −1⎯ + 1 µA
Pull-up
resistance RUP
P00 to P07,
P10 to P17,
P20 to P27,
P30 to P37,
RST
⎯25 50 100 kΩ
Pull-down
resistance RDOWN MD2 ⎯25 50 100 kΩExcept
Flash
devices
Power supply
current*
ICC
VCC
VCC = 5.0 V,
Internal frequency : 24 MHz,
during normal operation.
⎯55 70 mA
VCC = 5.0 V,
Internal frequency : 24 MHz,
when writing FLASH memory.
⎯70 85 mA Flash
devices
VCC = 5.0 V,
Internal frequency : 24 MHz,
when erasing FLASH memory.
⎯75 90 mA Flash
devices
ICCS
VCC = 5.0 V,
Internal frequency : 24 MHz,
in Sleep mode.
⎯25 35 mA
ICTS
VCC = 5.0 V,
Internal frequency : 2 MHz,
in Main Timer mode
⎯0.3 0.8 mA
ICTSPLL6
VCC = 5.0 V,
Internal frequency : 24 MHz,
in PLL Timer mode,
external frequency = 4 MHz
⎯47mA
ICCL
VCC = 5.0 V
Internal frequency : 8 kHz,
during sub operation
TA = +25°C
⎯70 140 µA
ICCLS
VCC = 5.0 V
Internal frequency : 8 kHz,
during sub sleep
TA = +25°C
⎯20 50 µA
ICCT
VCC = 5.0 V
Internal frequency : 8 kHz,
in watch mode
TA = +25°C
⎯10 35 µA
ICCH
VCC = 5.0 V,
in Stop mode,
TA = +25°C
⎯725µA
Input capacitance CIN
Other than C,
AVCC, AVSS,
AVRH, AVRL,
VCC, VSS
⎯⎯515pF
MB90860E Series
44 DS07-13748-5E
4. AC Characteristics
(1) Clock Timing (TA = −40 °C to +105 °C, VCC = 5.0 V ± 10%, fCP ≤ 24 MHz, VSS = AVSS = 0 V)
* : When selecting the PLL clock, the range of clock frequency is limited. Use this product within the range as
mentioned in “Relation between the external clock frequency and machine clock frequency”.
Parameter Symbol Pin Value Unit Remarks
Min Typ Max
Clock frequency fCX0, X1
3⎯16 MHz 1/2 (at PLL stop)
When using an oscillator circuit
4⎯16 MHz PLL multiplied by 1
When using an oscillator circuit*
4⎯12 MHz PLL multiplied by 2
When using an oscillator circuit*
4⎯8MHz
PLL multiplied by 3
When using an oscillator circuit*
4⎯6MHz
PLL multiplied by 4
When using an oscillator circuit*
⎯⎯ 4MHz
PLL multiplied by 6
When using an oscillator circuit*
3⎯24 MHz When using an external clock
fCL X0A, X1A ⎯32.768 100 kHz
Clock cycle time tCYL
X0, X1 62.5 ⎯333 ns When using an oscillator circuit
X0, X1 41.67 ⎯333 ns When using an external clock
tCYLL X0A, X1A 10 30.5 ⎯µs
Input clock
pulse width
PWH, PWL X0 10 ⎯⎯ns Duty ratio is about 30% to 70%.
PWHL, PWLL X0A 5 15.2 ⎯µs
Input clock rise and
fall time tCR, tCF X0 ⎯⎯ 5 ns When using external clock
Internal operating
clock frequency
(machine clock)
fCP ⎯1.5 ⎯24 MHz When using main clock
fCPL ⎯⎯8.192 50 kHz When using sub clock
Internal operating
clock cycle time
(machine clock)
tCP ⎯41.67 ⎯666 ns When using main clock
tCPL ⎯20 122.1 ⎯µs When using sub clock
X0
t
CYL
t
CF
t
CR
0.8 V
CC
0.2 V
CC
P
WH
P
WL
X0A
t
CYLL
t
CF
t
CR
0.8 V
CC
0.2 V
CC
P
WHL
P
WLL
•Clock Timing
MB90860E Series
DS07-13748-5E 45
• Guaranteed PLL operation range
Guaranteed operation range of MB90860E series
* : When using a crystal oscillator or a ceramic oscillator, the maximum oscillation clock frequency is 16 MHz
24
5.5
3.5
1.5 4
Power supply voltage
VCC (V)
Guaranteed operation range
Guaranteed PLL operation range
4.0
Guaranteed A/D Converter
operation range
Machine clock fCP (MHz)
24
4.0
16
12
3412 24
Internal clock
fCP (MHz)
External clock fC (MHz) *
× 4 × 3 × 2 × 1
× 1/2
(PLL off)
8
8
Guaranteed oscillation frequency range
1.5
16
× 6
MB90860E Series
46 DS07-13748-5E
(2) Reset Standby Input
(TA = −40 °C to +105 °C, VCC = 5.0 V ± 10%, fCP ≤ 24 MHz, VSS = AVSS = 0.0 V)
* : The oscillation time of the oscillator is the time it takes for the amplitude to reach 90%. In crystal oscillators, the
oscillation time is between several ms and to tens of ms. In crystal oscillators, the oscillation time is between
hundreds of µs to several ms. For an external clock, the oscillation time is 0 ms.
Parameter Symbol Pin Value Unit Remarks
Min Max
Reset input
time tRSTL RST
500 ⎯ns During normal operation
Oscillation time of oscillator*
+ 100 µs⎯µs
In Stop mode, Sub Clock
mode, Sub Sleep mode
and Watch mode
100 ⎯µs In Time Timer mode
tRSTL
0.2 VCC 0.2 VCC
100 µs
RST
X0
90% of
amplitude
Instruction execution
Oscillation stabilization
waiting time
Oscillation time
of oscillator
Internal operation
clock
Internal reset
0.2 VCC
RST
tRSTL
0.2 VCC
During normal operation:
In Stop mode, Sub Clock mode, Sub Sleep mode, Watch mode, Power-on:
MB90860E Series
DS07-13748-5E 47
(3) Power On Reset
(TA = −40 °C to +105 °C, VCC = 5.0 V ± 10%, fCP ≤ 24 MHz, VSS = AVSS = 0.0 V)
(4) Clock Output Timing
(TA = −40 °C to +105 °C, VCC = 5.0 V ± 10%, VSS = 0.0 V, fCP ≤ 24 MHz)
Parameter Symbol Pin Condition Value Unit Remarks
Min Max
Power on rise time tRVCC ⎯0.05 30 ms
Power off time tOFF VCC 1⎯ms Waiting time until power-on
Parameter Symbol Pin Condition Value Unit Remarks
Min Max
Cycle time tCYC CLK ⎯62.5 ⎯ns fCP = 16 MHz
41.67 ⎯ns fCP = 24 MHz
CLK ↑ → CLK ↓tCHCL CLK ⎯20 ⎯ns fCP = 16 MHz
13 ⎯ns fCP = 24 MHz
VCC
VCC
VSS
3 V
tR
tOFF
2.7 V
0.2 V 0.2 V0.2 V
Holds RAM data
We recommend a rise of
50 mV/ms maximum.
If you change the power supply voltage too rapidly, a power on reset may occur. If the
power supply voltage is varied while the device is operating, it is recommended that
variation be limited such that the supply voltage rises smoothly as shown in the
following diagram. The supply voltage should be changed while the PLL clock is not
being used. However, the device can be operated while the PLL is being used if the
rate of change is less than 1 V/s.
CLK
2.4 V
tCYC
2.4 V
0.8 V
tCHCL
MB90860E Series
48 DS07-13748-5E
(5) Bus Timing (Read)
(TA = −40 °C to +105 °C, VCC = 5.0 V ± 10%, VSS = 0.0 V, fCP ≤ 24 MHz)
Parameter Sym-
bol Pin Condition Value Unit
Min Max
ALE pulse width tLHLL ALE
⎯
tCP/2 − 10 ⎯ns
Valid address → ALE ↓ time tAVLL ALE, A23 to A16,
AD15 to AD00 tCP/2 − 20 ⎯ns
ALE ↓ → Address valid time tLLAX ALE, AD15 to AD00 tCP/2 − 15 ⎯ns
Valid address → RD ↓ time tAVRL A23 to A16,
AD15 to AD00, RD tCP − 15 ⎯ns
Valid address → Valid data input tAVDV A23 to A16,
AD15 to AD00 ⎯5 tCP/2 − 60 ns
RD pulse width tRLRH RD 3 tCP/2 − 20 ⎯ns
RD ↓ → Valid data input tRLDV RD, AD15 to AD00 ⎯3 tCP/2 − 50 ns
RD ↑ → Data hold time tRHDX RD, AD15 to AD00 0 ⎯ns
RD ↑ → ALE ↑ time tRHLH RD, ALE tCP/2 − 15 ⎯ns
RD ↑ → Address valid time tRHAX RD, A23 to A16 tCP/2 − 10 ⎯ns
Valid address → CLK ↑ time tAVCH A23 to A16,
AD15 to AD00, CLK tCP/2 − 16 ⎯ns
RD ↓ → CLK ↑ time tRLCH RD, CLK tCP/2 − 15 ⎯ns
ALE ↓ → RD ↓ time tLLRL ALE, RD tCP/2 − 15 ⎯ns
A23 to A16
0.8 V
2.4 V
2.4 V
0.8 V
tRHAX
AD15 to AD00
0.8 V
2.4 V 2.4 V
0.8 V Address VIL
VIH VIH
VIL
Read data
tRHDX
tRLDV
tAVDV
CLK
tAVCH
2.4 V
tRLCH
2.4 V
ALE 2.4 V
tLHLL
2.4 V
tRHLH
0.8 V
tLLAX
2.4 V
tAVLL
RD
tLLRL
tRLRH
0.8 V
2.4 V
tAVRL
MB90860E Series
DS07-13748-5E 49
(6) Bus Timing (Write)
(TA = −40 °C to +105 °C, VCC = 5.0 V ± 10%, VSS = 0.0 V, fCP ≤ 24 MHz)
Parameter Symbol Pin Condition Value Unit
Min Max
Valid address → WR ↓ time tAVWL
A23 to A16,
AD15 to AD00,
WR
⎯
tCP−15 ⎯ns
WR pulse width tWLWH WR 3 tCP/2 − 20 ⎯ns
Valid data output → WR ↑ time tDVWH AD15 to AD00,
WR 3 tCP/2 − 20 ⎯ns
WR ↑ → Data hold time tWHDX AD15 to AD00,
WR 15 ⎯ns
WR ↑ → Address valid time tWHAX A23 to A16, WR tCP/2 − 10 ⎯ns
WR ↑ → ALE ↑ time tWHLH WR, ALE tCP/2 − 15 ⎯ns
WR ↓ → CLK ↑ time tWLCH WR, CLK tCP/2 − 15 ⎯ns
CLK
tWLCH
2.4 V
ALE
tWHLH
2.4 V
WR (WRL, WRH)
tWLWH
0.8 V
2.4 V
tAVWL
A23 to A16
0.8 V
2.4 V
2.4 V
0.8 V
tWHAX
AD15 to AD00 2.4 V
0.8 V Address 0.8 V
2.4 V
Write data
tDVWH
0.8 V
2.4 V
tWHDX
MB90860E Series
50 DS07-13748-5E
(7) Ready Input Timing
(TA = −40 °C to +105 °C, VCC = 5.0 V ± 10%, VSS = 0.0 V, fCP ≤ 24 MHz)
Note : If the RDY setup time is insufficient, use the auto-ready function.
Parameter Sym-
bol Pin Condition Rated Value Units Remarks
Min Max
RDY setup time tRYHS RDY ⎯
45 ⎯ns fCP = 16 MHz
32 ⎯ns fCP = 24 MHz
RDY hold time tRYHH RDY 0 ⎯ns
CLK 2.4 V
ALE
RD/WR
RDY
When WAIT is not used.
VIH VIH
tRYHH
RDY
When WAIT is used.
tRYHS
VIL
MB90860E Series
DS07-13748-5E 51
(8) Hold Timing
(TA = −40 °C to +105 °C, VCC = 5.0 V ± 10%, VSS = 0.0 V, fCP ≤ 24 MHz)
Note : It takes at least one machine clock cycle from when an HRQ is accepted until HAK changes.
Parameter Symbol Pin Condition Value Units
Min Max
Pin floating → HAK ↓ time tXHAL HAK ⎯30 tCP ns
HAK ↑ time → Pin valid time tHAHV HAK tCP 2 tCP ns
HAK
Each pin
High-Z
tHAHV
tXHAL
2.4 V
0.8 V
2.4 V 2.4 V
0.8 V 0.8 V
MB90860E Series
52 DS07-13748-5E
(9) LIN-UART0/1/2/3
• Bit setting: ESCR:SCES = 0, ECCR:SCDE = 0
(TA = −40 °C to +105 °C, VCC = 5.0 V ± 10%, fCP ≤ 24 MHz, VSS = 0 V)
Notes : • AC characteristic in CLK synchronized mode.
• CL is load capacity value of pins when testing.
• tCP is internal operating clock cycle time (machine clock) . Refer to “ (1) Clock Timing”.
Parameter Symbol Pin Condition Value Unit
Min Max
Serial clock cycle time tSCYC SCK0 to SCK3
Internal shift clock
mode output pins are
CL = 80 pF + 1 TTL.
5 tCP ⎯ns
SCK ↓ → SOT delay time tSLOVI SCK0 to SCK3
SOT0 to SOT3 −50 +50 ns
Valid SIN → SCK ↑tIVSHI SCK0 to SCK3
SIN0 to SIN3 tCP + 80 ⎯ns
SCK ↑ → Valid SIN hold time tSHIXI SCK0 to SCK3
SIN0 to SIN3 0⎯ns
Serial clock “L” pulse width tSHSL SCK0 to SCK3
External shift clock
mode output pins are
CL = 80 pF + 1 TTL.
3 tCP - tR⎯ns
Serial clock “H” pulse width tSLSH SCK0 to SCK3 tCP + 10 ⎯ns
SCK ↓ → SOT delay time tSLOVE SCK0 to SCK3
SOT0 to SOT3 ⎯2 tCP + 60 ns
Valid SIN → SCK ↑tIVSHE SCK0 to SCK3
SIN0 to SIN3 30 ⎯ns
SCK ↑ → Valid SIN hold time tSHIXE SCK0, SCK1,
SIN0 to SIN3 tCP + 30 ⎯ns
SCK fall time tFSCK0 to SCK3 ⎯10 ns
SCK rise time tRSCK0 to SCK3 ⎯10 ns
SCK0 to SCK3
2.4 V
0.8 V
SOT0 to SOT3
0.8 V
2.4 V
0.8 V
tSLOVI
SIN0 to SIN3
VIL
VIH
VIL
VIH
tSCYC
tIVSHI tSHIXI
• Internal Shift Clock Mode
MB90860E Series
DS07-13748-5E 53
• Bit setting: ESCR:SCES = 1, ECCR:SCDE = 0
(TA = −40 °C to +105 °C, VCC = 5.0 V ± 10%, fCP ≤ 24 MHz, VSS = 0 V)
Notes : • CL is load capacity value of pins when testing.
• tCP is internal operating clock cycle time (machine clock) . Refer to “ (1) Clock Timing”.
Parameter Symbol Pin Condition Value Unit
Min Max
Serial clock cycle time tSCYC SCK0 to SCK3
Internal shift clock
mode output pins are
CL = 80 pF + 1 TTL.
5 tCP ⎯ns
SCK ↑ → SOT delay time tSHOVI SCK0 to SCK3
SOT0 to SOT3 −50 +50 ns
Valid SIN → SCK ↓tIVSLI SCK0 to SCK3
SIN0 to SIN3 tCP + 80 ⎯ns
SCK ↓ → Valid SIN hold time tSLIXI SCK0 to SCK3
SIN0 to SIN3 0⎯ns
Serial clock “H” pulse width tSHSL SCK0 to SCK3
External shift clock
mode output pins are
CL = 80 pF + 1 TTL.
3 tCP - tR⎯ns
Serial clock “L” pulse width tSLSH SCK0 to SCK3 tCP + 10 ⎯ns
SCK ↑ → SOT delay time tSHOVE SCK0 to SCK3
SOT0 to SOT3 ⎯2 tCP + 60 ns
Valid SIN → SCK ↓tIVSLE SCK0 to SCK3
SIN0 to SIN3 30 ⎯ns
SCK ↓ → Valid SIN hold time tSLIXE SCK0 to SCK3
SIN0 to SIN3 tCP + 30 ⎯ns
SCK fall time tFSCK0 to SCK3 ⎯10 ns
SCK rise time tRSCK0 to SCK3 ⎯10 ns
• External Shift Clock Mode
SCK0 to SCK3 VIH
VIL
SOT0 to SOT3
0.8 V
2.4 V
tSLOVE
SIN0 to SIN3
VIL
VIH
VIL
VIH
VIH
VIL
tR
tF
tSHSL
tSLSH
tIVSHE tSHIXE
MB90860E Series
54 DS07-13748-5E
• Internal Shift Clock Mode
SCK0 to SCK3
2.4 V
t
SCYC
0.8 V
SOT0 to SOT3
0.8 V
2.4 V
t
SHOVI
SIN0 to SIN3
V
IL
V
IH
t
IVSLI
V
IL
V
IH
t
SLIXI
• External Shift Clock Mode
SCK0 to SCK3
V
IH
V
IL
SOT0 to SOT3
0.8 V
2.4 V
t
SHOVE
SIN0 to SIN3
V
IL
V
IH
t
IVSLE
V
IL
V
IH
t
SLIXE
V
IH
V
IL
t
SHSL
t
R
t
F
t
SLSH
MB90860E Series
DS07-13748-5E 55
• Bit setting: ESCR:SCES = 0, ECCR:SCDE = 1
(TA = −40 °C to +105 °C, VCC = 5.0 V ± 10%, fCP ≤ 24 MHz, VSS = 0 V)
Notes : • CL is load capacity value of pins when testing.
• tCP is internal operating clock cycle time (machine clock) . Refer to “ (1) Clock Timing”.
Parameter Symbol Pin Condition Value Unit
Min Max
Serial clock cycle time tSCYC SCK0 to SCK3
Internal clock operation
output pins are
CL = 80 pF + 1 TTL.
5 tCP ⎯ns
SCK ↑ → SOT delay time tSHOVI SCK0 to SCK3
SOT0 to SOT3 −50 +50 ns
Valid SIN → SCK ↓tIVSLI SCK0 to SCK3
SIN0 to SIN3 tCP + 80 ⎯ns
SCK ↓ → Valid SIN hold time tSLIXI SCK0 to SCK3
SIN0 to SIN3 0⎯ns
SOT → SCK ↓ delay time tSOVLI SCK0 to SCK3
SOT0 to SOT3 3 tCP − 70 ⎯ns
SCK0 to SCK3
2.4 V
tSCYC
0.8 V
SOT0 to SOT3
0.8 V
2.4 V
tSOVLI
SIN0 to SIN3
VIL
VIH
tIVSLI
VIL
VIH
tSLIXI
0.8 V
tSHOVI
0.8 V
2.4 V
MB90860E Series
56 DS07-13748-5E
• Bit setting: ESCR:SCES = 1, ECCR:SCDE = 1
(TA = −40 °C to +105 °C, VCC = 5.0 V ± 10%, fCP ≤ 24 MHz, VSS = 0 V)
Notes : • CL is load capacity value of pins when testing.
• tCP is internal operating clock cycle time (machine clock) . Refer to “ (1) Clock Timing”.
Parameter Symbol Pin Condition Value Unit
Min Max
Serial clock cycle time tSCYC SCK0 to SCK3
Internal clock operation
output pins are
CL = 80 pF + 1 TTL.
5 tCP ⎯ns
SCK ↓ → SOT delay time tSLOVI SCK0 to SCK3
SOT0 to SOT3 −50 +50 ns
Valid SIN → SCK ↑tIVSHI SCK0 to SCK3
SIN0 to SIN3 tCP + 80 ⎯ns
SCK ↑ → Valid SIN hold time tSHIXI SCK0 to SCK3
SIN0 to SIN3 0⎯ns
SOT → SCK ↑ delay time tSOVHI SCK0 to SCK3
SOT0 to SOT3 3 tCP − 70 ⎯ns
SCK0 to SCK32.4 V
t
SCYC
2.4 V
SOT0 to SOT30.8 V
2.4 V
t
SOVHI
SIN0 to SIN3V
IL
V
IH
t
IVSHI
V
IL
V
IH
t
SHIXI
0.8 V
t
SLOVI
0.8 V
2.4 V
MB90860E Series
DS07-13748-5E 57
(10) Trigger Input Timing
(TA = −40 °C to +105 °C, VCC = 5.0 V ± 10%, fCP ≤ 24 MHz, VSS = 0 V)
Parameter Symbol Pin Condition Value Unit
Min Max
Input pulse width tTRGH
tTRGL
INT0 to INT15,
INT8R to INT15R,
ADTG
⎯5 tCP ⎯ns
VIL
VIH
tTRGH
VIL
VIH
tTRGL
INT0 to INT15,
INT8R to INT15R,
ADTG
MB90860E Series
58 DS07-13748-5E
(11) Timer Related Resource Input Timing
(TA = −40 °C to +105 °C, VCC = 5.0 V ± 10%, fCP ≤ 24 MHz, VSS = 0 V)
(12) Timer Related Resource Output Timing
(TA = –40°C to +105°C, VCC = 5.0 V ± 10%, fCP ≤ 24 MHz, VSS = 0.0 V)
Parameter Symbol Pin Condition Value Unit
Min Max
Input pulse width tTIWH TIN0 to TIN3,
IN0 to IN7 ⎯4 tCP ⎯ns
tTIWL
Parameter Symbol Pin Condition Value Unit
Min Max
CLK ↑ → TOUT change time tTO TOT0 to TOT3,
PPG0 to PPGF ⎯30 ⎯ns
VIL
VIH
tTIWH
VIL
VIH
tTIWL
TIN0 to TIN3,
IN0 to IN7
CLK 2.4 V
0.8 V
2.4 V
tTO
TOT0 to TOT3,
PPG0 to PPGF
MB90860E Series
DS07-13748-5E 59
(13) I2C Timing
(TA = –40°C to +105°C, VCC = 5.0 V ± 10%, VSS = 0.0 V)
*1 : For use at over 100 kHz, set the machine clock to at least 6 MHz.
*2 : R,C : Pull-up resistance and load capacitance of the SCL and SDA lines.
*3 : The maximum tHDDAT must be satisfied if the device does not extend the “L” width (tLOW) of the SCL signal.
*4 : A Fast-mode I2C-bus device can be used in a Standard-mode I2C-bus system, but the requirement
tSUDAT ≥ 250 ns must then be met.
Parameter Symbol Condition Standard-mode Fast-mode*1
Unit
Min Max Min Max
SCL clock frequency fSCL
R = 1.7 kΩ,
C = 50 pF*2
0 100 0 400 kHz
Hold time (repeated) START condition
SDA ↓ → SCL ↓tHDSTA 4.0 ⎯0.6 ⎯µs
“L” width of the SCL clock tLOW 4.7 ⎯1.3 ⎯µs
“H” width of the SCL clock tHIGH 4.0 ⎯0.6 ⎯µs
Set-up time for a repeated START condition
SCL ↑ → SDA ↓tSUSTA 4.7 ⎯0.6 ⎯µs
Data hold time
SCL ↓ → SDA ↓ ↑tHDDAT 0 3.45*300.9*
4µs
Data set-up time
SDA ↓ ↑ → SCL ↑tSUDAT 250 ⎯100 ⎯ns
Set-up time for STOP condition
SCL ↑ → SDA ↑tSUSTO 4.0 ⎯0.6 ⎯µs
Bus free time between a STOP and START
condition tBUS 4.7 ⎯1.3 ⎯µs
SDA
SCL
tLOW tSUDAT tHDSTA tBUS
tHDSTA tHDDAT tHIGH tSUSTA tSUSTO
MB90860E Series
60 DS07-13748-5E
5. A/D Converter
(TA = −40 °C to +105 °C, 3.0 V ≤ AVRH − AVRL, VCC = AVCC = 5.0 V ± 10%, fCP ≤ 24 MHz, VSS = AVSS = 0 V)
* : This is the current when the A/D converter is not being operated, and the CPU is stopped (VCC = AVCC = AVRH
= 5.0 V) .
Note : The relative error increases as AVRH − AVRL becomes smaller.
Parameter Symbol Pin Value Unit Remarks
Min Typ Max
Resolution ⎯⎯ ⎯ ⎯ 10 bit
Total error ⎯⎯ ⎯ ⎯ ±3.0 LSB
Nonlinearity error ⎯⎯ ⎯ ⎯ ±2.5 LSB
Differential
nonlinearity error ⎯⎯ ⎯ ⎯ ±1.9 LSB
Zero reading
voltage VOT AN0 to AN23 AVRL −
1.5 × LSB
AVRL +
0.5 × LSB
AVRL +
2.5 × LSB V
Full scale reading
voltage VFST AN0 to AN23 AVRH −
3.5 × LSB
AVRH −
1.5 × LSB
AVRH +
0.5 × LSB V
Compare time ⎯⎯ 1.0 ⎯16500 µs4.5 V ≤ AVCC ≤ 5.5 V
2.0 4.0 V ≤ AVCC < 4.5 V
Sampling time ⎯⎯ 0.5 ⎯∞µs4.5 V ≤ AVCC ≤ 5.5 V
1.2 4.0 V ≤ AVCC < 4.5 V
Analog port input
current IAIN AN0 to AN23 −0.3 ⎯+0.3 µA
Analog input
voltage VAIN AN0 to AN23 AVRL ⎯AVRH V
Reference
voltage
⎯AVRH AVRL + 2.7 ⎯AVCC V
⎯AVRL 0 ⎯AVRH − 2.7 V
Power supply
current
IAAVCC ⎯3.5 7.5 mA
IAH AVCC ⎯⎯ 5µA*
Reference
voltage current
IRAVRH ⎯600 900 µA
IRH AVRH ⎯⎯ 5µA*
Variation between
input channels ⎯AN0 to AN23 ⎯⎯ 4LSB
MB90860E Series
DS07-13748-5E 61
6. Definition of A/D Converter Terms
(Continued)
Resolution : Analog variation that is recognized by an A/D converter.
Non linearity
error
: Deviation of the actual conversion characteristics from a line that connects the zero transition
point ( “00 0000 0000” ← → “00 0000 0001” ) to the full-scale transition point ( “11 1111 1110”
← → “11 1111 1111” ) .
Differential
linearity error
: Deviation from the ideal value of the input voltage required to change the output code by
LSB.
Total error : Difference between the actual value and the ideal value. The total error includes zero transi-
tion error, full-scale transition error, and linear error.
3FFH
3FEH
3FDH
004H
003H
002H
001H
AVRL AVRH
VNT
1.5 LSB
0.5 LSB
{1 LSB × (N − 1) + 0.5 LSB}
Actual conversion
characteristics
(Actually-measured value)
Actual conversion
characteristics
Ideal characteristics
Digital output
Analog input
Total error
Total error of digital output “N” = VNT − {1 LSB × (N − 1) + 0.5 LSB}
1 LSB [LSB]
1 LSB (Ideal value) = AVRH − AVRL
1024 [V]
VOT (Ideal value) = AVRL + 0.5 LSB [V]
VFST (Ideal value) = AVRH − 1.5 LSB [V]
VNT : The voltage at which the digital output changes from (N − 1) H to NH.
N : A/D converter digital output value
MB90860E Series
62 DS07-13748-5E
(Continued)
3FF
H
3FE
H
3FD
H
004
H
003
H
002
H
001
H
AVRL AVRH AVRL AVRH
N + 1
H
N
H
N − 1
H
N − 2
H
V
OT
(actual measurement value)
{1 LSB × (N − 1)
+ V
OT
}
Actual conversion
characteristics
V
FST
(actual
measurement
value)
V
NT
(actual
measurement value)
Actual conversion
characteristics
Ideal characteristics
Actual conversion
characteristics
Actual conversion
characteristics
Ideal
characteristics
Digital output
Digital output
Analog inputAnalog input
V
NT
(actual measurement value)
V
(N + 1) T
(actual measurement
value)
Non linearity error Differential linearity error
Non linearity error of digital output N =VNT − {1 LSB × (N − 1) + VOT}
1 LSB [LSB]
Differential linearity error of digital output N =V (N+1) T − VNT
1 LSB −1 LSB [LSB]
VFST − VOT
1022 [V]
1 LSB =
N : A/D converter digital output value
VOT : The voltage at which the digital output changes from “000H” to “001H.”
VFST : The voltage at which the digital output changes from “3FEH” to “3FFH.”
MB90860E Series
DS07-13748-5E 63
7. Notes on A/D Converter Unit
Use the device such that the output impedance of the external circuits attached to the analog inputs satisfy the
following conditions.
• It is recommended that the output impedance of external circuits are approx. 1.5 kΩ or lower
(4.0 V ≤ AVCC ≤ 5.5 V, sampling period = 0.5 µs)
• If an external capacitor is used, in consideration of the capacitive voltage division effect between the external
capacitor and the internal on-chip capacitor, it is recommended that the capacitance of the external capacitor
is several thousand times greater than the internal capacitor.
• If the output impedance of the external circuit is too high, the sampling period for the analog voltage may be
insufficient.
8. Flash Memory Program/Erase Characteristics
* : This value is the result of evaluating the reliability of the technology (using Arrhenius equation to translate high
temperature measurements into normalized value at +85 °C) .
Parameter Conditions Value Unit Remarks
Min Typ Max
Sector erase time
TA = +25 °C
VCC = 5.0 V
⎯115s
Excludes programming
prior to erasure
Chip erase time ⎯9⎯sExcludes programming
prior to erasure
Word (16-bit width)
programming time ⎯16 3600 µsExcept for the over head
time of the system
Number of program/
erase cycles ⎯10000 ⎯⎯cycle
Flash data retention time Average
TA = +85 °C20 ⎯⎯Year *
C
Comparator
Analog input R
4.5 V ≤ AVCC ≤ 5.5 V : R := 2.52 kΩ, C := 10.7 pF
4.0 V ≤ AVCC < 4.5 V : R := 13.6 kΩ, C := 10.7 pF
• Analog input circuit model
Note : The values shown in this figure are reference values.
MB90860E Series
64 DS07-13748-5E
■EXAMPLE CHARACTERISTICS
• MB90F867E, MB90F867ES
ICC − VCC ICCL − VCC
TA = +25 °C, operating on external clock
f = Internal operation frequency
TA = +25 °C, operating on external clock
f = Internal operation frequency
ICCS − VCC ICCLS − VCC
TA = +25 °C, operating on external clock
f = Internal operation frequency
TA = +25 °C, operating on external clock
f = Internal operation frequency
ICTS − VCC ICCT − VCC
TA = +25 °C, operating on external clock
f = Internal operation frequency
TA = +25 °C, operating on external clock
f = Internal operation frequency
ICTSPLL6 − VCC ICCH − VCC
TA = +25 °C, operating on external clock
f = Internal operation frequency TA = +25 °C, when stopped
ICC (mA)
70
30
10
20
VCC (V)
0
40
50
60
2.5 3.5 4.5 5.5 6.5
f = 24 MHz
f = 20 MHz
f = 16 MHz
f = 12 MHz
f = 10 MHz
f = 8 MHz
f = 4 MHz
f = 2 MHz
ICCL ( A)
100
30
10
20
VCC (V)
0
40
50
60
2.5 3.5 4.5 5.5 6.5
f = 8 kHz
90
70
80
ICCS (mA)
35
15
5
10
VCC (V)
0
20
25
30
2.5 3.5 4.5 5.5 6.5
f = 24 MHz
f = 20 MHz
f = 16 MHz
f = 12 MHz
f = 10 MHz
f = 8 MHz
f = 4 MHz
f = 2 MHz
ICCLS ( A)
50
15
5
10
VCC (V)
0
20
30
40
2.5 3.5 4.5 5.5 6.5
f = 8 kHz
45
25
35
ICTS ( A)
400
150
50
100
VCC (V)
0
200
300
2.5 3.5 4.5 5.5 6.5
f = 2 MHz
350
250
ICCT ( A)
20
10
6
8
VCC (V)
0
12
16
2.5 3.5 4.5 5.5 6.5
f = 8 kHz
18
14
4
2
ICTSPLL6 (mA)
10
3
1
2
VCC (V)
0
4
8
2.5 3.5 4.5 5.5 6.5
f = 24 MHz
9
6
5
7
ICCH ( A)
10
5
1
2
VCC (V)
0
6
8
2.5 3.5 4.5 5.5 6.5
9
7
3
4
MB90860E Series
DS07-13748-5E 65
• MB90867E, MB90867ES
ICC − VCC ICCL − VCC
TA = +25 °C, operating on external clock
f = Internal operation frequency
TA = +25 °C, operating on external clock
f = Internal operation frequency
ICCS − VCC ICCLS − VCC
TA = +25 °C, operating on external clock
f = Internal operation frequency
TA = +25 °C, operating on external clock
f = Internal operation frequency
ICTS − VCC ICCT − VCC
TA = +25 °C, operating on external clock
f = Internal operation frequency
TA = +25 °C, operating on external clock
f = Internal operation frequency
ICTSPLL6 − VCC ICCH − VCC
TA = +25 °C, operating on external clock
f = Internal operation frequency TA = +25 °C, when stopped
ICC (mA)
70
30
10
20
VCC (V)
0
40
50
60
2.5 3.5 4.5 5.5 6.5
f = 24 MHz
f = 20 MHz
f = 16 MHz
f = 12 MHz
f = 10 MHz
f = 8 MHz
f = 4 MHz
f = 2 MHz
ICCL (µA)
100
30
10
20
VCC (V)
0
40
50
60
2.5 3.5 4.5 5.5 6.5
f = 8 kHz
90
70
80
ICCS (mA)
35
15
5
10
VCC (V)
0
20
25
30
2.5 3.5 4.5 5.5 6.5
f = 24 MHz
f = 20 MHz
f = 16 MHz
f = 12 MHz
f = 10 MHz
f = 8 MHz
f = 4 MHz
f = 2 MHz
ICCLS (µA)
50
15
5
10
VCC
(
V
)
0
20
30
40
2.5 3.5 4.5 5.5 6.5
f = 8 kHz
45
25
35
ICTS (µA)
400
150
50
100
VCC (V)
0
200
300
2.5 3.5 4.5 5.5 6.5
f = 2 MHz
350
250
ICCT (µA)
20
10
6
8
VCC (V)
0
12
16
2.5 3.5 4.5 5.5 6.5
f = 8 kHz
18
14
4
2
ICTSPLL6 (mA)
10
3
1
2
VCC (V)
0
4
8
2.5 3.5 4.5 5.5 6.5
f = 24 MHz
9
6
5
7
ICCH (µA)
10
5
1
2
VCC (V)
0
6
8
2.5 3.5 4.5 5.5 6.5
9
7
3
4
MB90860E Series
66 DS07-13748-5E
• I/O characteristics
(VCC−VOH) − IOH VOL − IOL
TA = +25 °C, VCC = 4.5 V TA = +25 °C, VCC = 4.5 V
Automotive VIN − VCC CMOS VIN − VCC
TA = +25 °C
UART-SIN pin, other than I2C pin
TA = +25 °C
TTL VIN − VCC CMOS VIN − VCC
TA = +25 °C
UART-SIN pin, I2C pin
TA = +25 °C
VCC VOH (mV)
800
300
100
200
IOH (mA)
0
400
500
600
024 7 10
700
13 6589
VOL (mV)
1000
300
100
200
IOL (mA)
0
400
500
600
900
700
800
024 7 1013 6589
VIN (V)
5.0
1.5
0.5
1.0
VCC (V)
0.0
2.0
3.0
3.5
2.5
2.5 3.5 4.5 5.5 6.53.0 4.0 5.0 6.0 7.0
4.0
4.5 VIHA
VILA
VIN (V)
5.0
2.5
1.5
2.0
VCC (V)
0.0
3.0
4.0
2.5 3.5 4.5 5.5 6.5
4.5
3.5
1.0
0.5
VIHS
VILS
3.0 4.0 5.0 6.0 7.0
VIN (V)
2.5
0.8
0.3
0.5
VCC (V)
0.0
1.0
2.0
2.5 3.5 4.5 5.5 6.5
2.3
1.5
1.3
1.8
3.0 4.0 5.0 6.0 7.0
VIHT
VILT
VIN (V)
5.0
2.5
0.5
1.0
VCC (V)
0.0
3.0
4.0
4.5
3.5
1.5
2.0
2.5 3.5 4.5 5.5 6.53.0 4.0 5.0 6.0 7.0
VIHS
VILS
MB90860E Series
DS07-13748-5E 67
■ORDERING INFORMATION
Part number Package Remarks
MB90F867EPF 100-pin plastic QFP
(FPT-100P-M06)
Flash memory product
MB90F867ESPF
MB90F867EPMC 100-pin plastic LQFP
(FPT-100P-M20)
MB90F867ESPMC
MB90867EPF 100-pin plastic QFP
(FPT-100P-M06)
MASK ROM product
MB90867ESPF
MB90867EPMC 100-pin plastic LQFP
(FPT-100P-M20)
MB90867ESPMC
MB90V340E-101CR 299-pin ceramic PGA
(PGA-299C-A01) Evaluation product
MB90V340E-102CR
MB90860E Series
68 DS07-13748-5E
■PACKAGE DIMENSIONS
Please confirm the latest Package dimension by following URL.
http://edevice.fujitsu.com/package/en-search/
(Continued)
100-pin plastic QFP Lead pitch 0.65 mm
Package width ×
package length 14.00 × 20.00 mm
Lead shape Gullwing
Sealing method Plastic mold
Mounting height
3.35 mm MAX
Code
(Reference) P-QFP100-14×20-0.65
100-pin plastic QFP
(FPT-100P-M06)
(
FPT-100P-M06
)
C
2002 FUJITSU LIMITED F100008S-c-5-5
130
31
50
5180
81
100
20.00±0.20(.787±.008)
23.90±0.40(.941±.016)
14.00±0.20
(.551±.008)
17.90±0.40
(.705±.016)
INDEX
0.65(.026) 0.32±0.05
(.013±.002)
M
0.13(.005)
"A"
0.17±0.06
(.007±.002)
0.10(.004)
Details of "A" part
(.035±.006)
0.88±0.15
(.031±.008)
0.80±0.20
0.25(.010)
3.00 +0.35
–0.20
+.014
–.008
.118
(Mounting height)
0.25±0.20
(.010±.008)
(Stand off)
0~8
˚
*
*
Dimensions in mm (inches).
Note: The values in parentheses are reference values.
©2002-2008 FUJITSU MICROELECTRONICS LIMITED F100008S-c-5-6
Note 1) * : These dimensions do not include resin protrusion.
Note 2) Pins width and pins thickness include plating thickness.
Note 3) Pins width do not include tie bar cutting remainder.
MB90860E Series
DS07-13748-5E 69
(Continued)
Please confirm the latest Package dimension by following URL.
http://edevice.fujitsu.com/package/en-search/
100-pin plastic LQFP Lead pitch 0.50 mm
Package width ×
package length 14.0 mm × 14.0 mm
Lead shape Gullwing
Sealing method Plastic mold
Mounting height
1.70 mm Max
Weight 0.65 g
Code
(Reference) P-LFQFP100-14×14-0.50
100-pin plastic LQFP
(FPT-100P-M20)
(FPT-100P-M20)
C
2005 -2008 FUJITSU MICROELECTRONICS LIMITED F100031S-c-3-3
14.00±0.10(.551±.004)SQ
16.00±0.20(.630±.008)SQ
125
26
51
76 50
75
100
0.50(.020) 0.20±0.05
(.008±.002)
M
0.08(.003)0.145±0.055
(.0057±.0022)
0.08(.003)
"A"
INDEX .059
–
.004
+.008
–
0.10
+0.20
1.50
(Mounting height)
0°~8°
0.50±0.20
(.020±.008)
(.024±.006)
0.60±0.15
0.25(.010)
0.10±0.10
(.004±.004)
Details of "A" part
(Stand off)
*
Dimensions in mm (inches).
Note: The values in parentheses are reference values
Note 1) * : These dimensions do not include resin protrusion.
Note 2) Pins width and pins thickness include plating thickness.
Note 3)Pins width do not include tie bar cutting remainder.
MB90860E Series
70 DS07-13748-5E
■MAIN CHANGES IN THIS EDITION
The vertical lines marked in the left side of the page show the changes.
Page Section Change Results
⎯⎯
Changed the package.
FPT-100P-M05 → FPT-100P-M20
60 ■ ELECTRICAL CHARACTERISTICS
5. A/D Converter
Changed the items for “Zero reading voltage” and “Full scale
reading voltage”.
67
■ ORDERING INFORMATION Changed the part numbers;
MB90867EPFV → MB90367EPMC
MB90867ESPFV → MB90867ESPMC
MB90F867EPFV → MB90F867EPMC
MB90F867ESPFV → MB90F867ESPMC
MB90V340E-101 → MB90V340E-101CR
MB90V340E-102 → MB90V340E-102CR
69 ■ PACKAGE DIMENSIONS Changed the package's figure.
FPT-100P-M05 → FPT-100P-M20
MB90860E Series
DS07-13748-5E 71
MEMO
MB90860E Series
FUJITSU MICROELECTRONICS LIMITED
Shinjuku Dai-Ichi Seimei Bldg. 7-1, Nishishinjuku 2-chome, Shinjuku-ku,
Tokyo 163-0722, Japan Tel: +81-3-5322-3347 Fax: +81-3-5322-3387
http://jp.fujitsu.com/fml/en/
For further information please contact:
North and South America
FUJITSU MICROELECTRONICS AMERICA, INC.
1250 E. Arques Avenue, M/S 333
Sunnyvale, CA 94085-5401, U.S.A.
Tel: +1-408-737-5600 Fax: +1-408-737-5999
http://www.fma.fujitsu.com/
Europe
FUJITSU MICROELECTRONICS EUROPE GmbH
Pittlerstrasse 47, 63225 Langen,
Germany
Tel: +49-6103-690-0 Fax: +49-6103-690-122
http://emea.fujitsu.com/microelectronics/
Korea
FUJITSU MICROELECTRONICS KOREA LTD.
206 KOSMO TOWER, 1002 Daechi-Dong,
Kangnam-Gu,Seoul 135-280
Korea
Tel: +82-2-3484-7100 Fax: +82-2-3484-7111
http://www.fmk.fujitsu.com/
Asia Pacific
FUJITSU MICROELECTRONICS ASIA PTE LTD.
151 Lorong Chuan, #05-08 New Tech Park,
Singapore 556741
Tel: +65-6281-0770 Fax: +65-6281-0220
http://www.fujitsu.com/sg/services/micro/semiconductor/
FUJITSU MICROELECTRONICS SHANGHAI CO., LTD.
Rm.3102, Bund Center, No.222 Yan An Road(E),
Shanghai 200002, China
Tel: +86-21-6335-1560 Fax: +86-21-6335-1605
http://cn.fujitsu.com/fmc/
FUJITSU MICROELECTRONICS PACIFIC ASIA LTD.
10/F., World Commerce Centre, 11 Canton Road
Tsimshatsui, Kowloon
Hong Kong
Tel: +852-2377-0226 Fax: +852-2376-3269
http://cn.fujitsu.com/fmc/tw
All Rights Reserved.
The contents of this document are subject to change without notice.
Customers are advised to consult with sales representatives before ordering.
The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose
of reference to show examples of operations and uses of FUJITSU MICROELECTRONICS device; FUJITSU MICROELECTRONICS
does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporat-
ing the device based on such information, you must assume any responsibility arising out of such use of the information.
FUJITSU MICROELECTRONICS assumes no liability for any damages whatsoever arising out of the use of the information.
Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use
or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU MICROELECTRONICS
or any third party or does FUJITSU MICROELECTRONICS warrant non-infringement of any third-party's intellectual property right or
other right by using such information. FUJITSU MICROELECTRONICS assumes no liability for any infringement of the intellectual
property rights or other rights of third parties which would result from the use of information contained herein.
The products described in this document are designed, developed and manufactured as contemplated for general use, including without
limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured
as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect
to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in
nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in
weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite).
Please note that FUJITSU MICROELECTRONICS will not be liable against you and/or any third party for any claims or damages arising
in connection with above-mentioned uses of the products.
Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by
incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current
levels and other abnormal operating conditions.
Exportation/release of any products described in this document may require necessary procedures in accordance with the regulations of
the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws.
The company names and brand names herein are the trademarks or registered trademarks of their respective owners.
Edited Business & Media Promotion Dept.
