http://www.tracopower.com Page 1 of 3
DC/DC Converters
TEM 2 Series, 2 Watt
The TEM 2 series is a family of isolated dc/dc converters in a DIP-24 package. They
offer tight line/load regulation and 1000 VDC I/O isolation. Standard features in-
clude an internal filter to reduce reflected input ripple currrent and to guarantee low
output noise. This product series provides a cost effective solution by many industrial
or consumer electronics appliactions.
Ordercode Input voltage range Output voltage Output current max. Efficiency typ.
TEM 2-0511 5 VDC 400 mA 50 %
TEM 2-0512 12 VDC 165 mA 54 %
TEM 2-0521 5 VDC ±10% ±12 VDC ±80 mA 53 %
TEM 2-0522 ±15 VDC ±65 mA 51 %
TEM 2-1211 5 VDC 400 mA 50 %
TEM 2-1212 12 VDC 165 mA 56 %
TEM 2-1221 12 VDC ±10% ±12 VDC ±80 mA 59 %
TEM 2-1222 ±15 VDC ±65 mA 59 %
TEM 2-2411 5 VDC 400 mA 51 %
TEM 2-2412 12 VDC 165 mA 61 %
TEM 2-2421 24 VDC ±10% ±12 VDC ±80 mA 61 %
TEM 2-2422 ±15 VDC ±65 mA 61 %
Features
DIL-24 plastic package
Tightly regulated output
Very low output noise
Short circuit protection
Operating temperature
range –25°C to +70°C
I/O isolation 1’000 VDC
Internal filter
Industry standard pinout
3-year product warranty
UL 60950 -1
C
B
Scheme
Models
not recommended for new design in
http://www.tracopower.com Page 2 of 3
All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated.
Input Specifications
Input current no load 5 Vin models: 80 mA typ.
12 Vin models: 40 mA typ.
24 Vin models: 20 mA typ.
Surge voltage (1 sec. max.) 5 Vin models: 7.5 V max.
12 Vin models: 15 V max.
24 Vin models: 30 V max.
Input filter Pi-Filter
Output Specifications
Voltage set accuracy ±3 %
Regulation – Input variation Vin min. to Vin max. ±0.3 % max.
– Load variation 10 – 100 %
single output models: ±0.5 % max.
dual output models balanced load: ±1.0 % max.
dual output models unbalanced load: ±3.0 % max.
Ripple and noise (20 MHz Bandwidth) 50 mVpk-pk max
Temperature coefficient ±0.02 %/K
Current limitation >120 % of Iout max., constant current
Short circuit protection indefinite
Capacitive load single output models: 470 µF max.
dual output models: 220 µF max.
General Specifications
Temperature ranges – Operating 25°C to +70°C
5 VDC output models: 25°C to +60°C
– Case temperature +95°C max.
– Storage –40°C to +125°C
Derating 3 %/K above +70°C
Humidity (non condensing) 95 % rel H max.
Reliability, calculated MTBF (MIL-HDBK-217F, at +25°C, ground benign) >800‘000 Mio. h
Isolation voltage (60 sec.) – Input/Output 1’000 VDC
Isolation capacitance – Input/Output 100 pF typ.
Isolation resistance – Input/Output (500 VDC) >1‘000 M Ohm
Switching frequency 80 kHz typ. (Pulse frequency modulation PFM)
Safety standards cUL/UL 60950-1, IEC/EN 60950-1
Environmental compliance – Reach www.tracopower.com/info/reach-declaration.pdf
– RoHS directive 2011/65/EU
DC/DC Converters
TEM 2 Series 2 Watt
Page 3 of 3
Specifications can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com
www.tracopower.com
Physical Specifications
Casing material non conductive plastic (UL94V-0 rated)
Weight 12 g (0.42 oz)
Soldering temperature max. 260°C / 10 sec.
Outline Dimensions mm (inches)
2.0
(0.08)
23
24 22
12 3
10.0
(0.39)
3.8
32.0
(1.26)
(0.1)(0.1)
2.54
(0.1)(0.1)
10 11 12
15 14 13
27.94
(1.1)
17.78
(0.7)
2.54 2.542.54
(0.15)
15.24 (0.6)
20.0 (0.79)
2.4
(0.094)
Bottom view
Pin diameter ø 0.5 ±0.05 (0.02) ±0.002
Tolerances ±0.5 (±0.02)
Pin Single Dual
1+Vin (Vcc) +Vin (Vcc)
2ntd. –Vout
3ntc. Common
10 –Vout Common
11 +Vout +Vout
12 –Vin (GND) –Vin (GND)
13 –Vin (GND) –Vin (GND)
14 +Vout +Vout
15 –Vout Common
22 ntc. Common
23 ntc. –Vout
24 +Vin (Vcc) +Vin (Vcc)
Pin-Out
DC/DC Converters
TEM 2 Series 2 Watt
Specifications can be changed any time without notice.
Rev. July 13, 2018
ntc. = not to connect