C0G (NP0) Dielectric General Specifications C0G (NP0) is the most popular formulation of the "temperature-compensating," EIA Class I ceramic materials. Modern C0G (NP0) formulations contain neodymium, samarium and other rare earth oxides. C0G (NP0) ceramics offer one of the most stable capacitor dielectrics available. Capacitance change with temperature is 0 30ppm/C which is less than 0.3% C from -55C to +125C. Capacitance drift or hysteresis for C0G (NP0) ceramics is negligible at less than 0.05% versus up to 2% for films. Typical capacitance change with life is less than 0.1% for C0G (NP0), one-fifth that shown by most other dielectrics. C0G (NP0) formulations show no aging characteristics. PART NUMBER (see page 2 for complete part number explanation) 0805 5 Size Voltage (L" x W") 6.3V = 6 10V = Z 16V = Y 25V = 3 50V = 5 100V = 1 200V = 2 500V = 7 A 101 J A T Dielectric Capacitance Code (In pF) Capacitance Tolerance Failure Rate A = Not Applicable Terminations T = Plated Ni and Sn C0G (NP0) = A 2 Sig. Digits + Number of Zeros B = .10 pF (<10pF) C = .25 pF (<10pF) D = .50 pF (<10pF) F = 1% ( 10 pF) G = 2% ( 10 pF) J = 5% K = 10% NOTE: Contact factory for availability of Termination and Tolerance Options for Specific Part Numbers. Contact factory for non-specified capacitance values. 4 Contact Factory For 1 = Pd/Ag Term 7 = Gold Plated NOT RoHS COMPLIANT A 2 Packaging 2 = 7" Reel 4 = 13" Reel U = 4mm TR (01005) Special Code A = Std. Product Contact Factory For Multiples 051818 C0G (NP0) (NP0)Dielectric Dielectric C0G Specificationsand andTest TestMethods Methods Specifications Parameter/Test Parameter/Test Operating Temperature Range Operating Temperature Capacitance Capacitance NP0 Specification Limits Range QQ Insulation Resistance Insulation Resistance Dielectric Strength Dielectric Strength Appearance Appearance Resistance Resistance to to Flexure Flexure Stresses Stresses Capacitance Capacitance Variation Variation Q Q Insulation Insulation Resistance Resistance Solderability Solderability Appearance Capacitance Appearance Variation Resistance to Resistance Solder to Heat Solder Heat Thermal Shock Thermal Shock Capacitance Variation Q Q Insulation Resistance Insulation Dielectric Resistance Strength Dielectric Appearance Strength Capacitance Appearance Variation Capacitance Variation Q Q Insulation Resistance Insulation Dielectric Resistance Strength Dielectric Appearance Strength Capacitance Appearance Variation Capacitance Load Life Load Life Load Humidity Load Humidity Variation Q (C=Nominal Cap) Q (C=Nominal Cap) Insulation Resistance Insulation Dielectric Resistance Strength Dielectric Appearance Strength Capacitance Appearance Variation Capacitance Q Variation Q Insulation Resistance Dielectric Insulation Strength Resistance Dielectric Strength 100917 051818 NP0 Specification Limits -55C +125C -55Cto to +125C Within specified tolerance Within specified tolerance <30 pF:pF: QQ 400+20 x Cap Value <30 400+20 x Cap Value 30 QQ 1000 30pF:pF: 1000 100,000Moror1000M 1000M - F, 100,000M - F, whichever is less whichever is less No breakdown or visual defects No breakdown or visual defects NoNo defects defects 5% or .5 pF, pF, whichever is greater 5% or .5 whichever is greater Measuring Conditions Measuring Conditions Temperature Cycle Chamber Temperature Cycle Chamber Freq.: 10% for for capcap 1000 pF pF Freq.:1.0 1.0MHz MHz 10% 1000 1.01.0 kHz 10% for cap > 1000 pF pF kHz 10% for cap > 1000 Voltage: .2V Voltage:1.0Vrms 1.0Vrms .2V Charge device withwith rated voltage for for Charge device rated voltage 60 @@ room temp/humidity 60 5 5secs secs room temp/humidity Charge with 250% of rated voltage for for Chargedevice device with 250% of rated voltage 1-5 and discharge current 1-5seconds, seconds,w/charge w/charge and discharge current limited to to 50 50 mAmA (max) limited (max) Note: Charge device with 150% of rated Note:voltage Chargefordevice with 150% of rated 500V devices. voltage for 500V devices. Deflection: 2mm Deflection: 2mm Test Time: 30 seconds Test Time: 30 seconds Meets Initial Values (As Above) Meets Initial Values (As Above) Initial Value x 0.3 Initial Value x 0.3 95% of each terminal should be covered with fresh solder 95% of each terminal should be covered No defects, <25% leaching of either end terminal with fresh solder No defects, <25% leaching of either end 2.5% or .25 pF, whichever is terminal greater Dip device in eutectic solder at 230 5C 5.0 solder 0.5 seconds Dip device infor eutectic at 230 5C for 5.0 0.5 seconds Meets Initial Values (As Above) Dip device in eutectic solder at 260C for 60 seconds. Store at room temperature for 24 2 Dip device in eutectic solder at 260C for 60sechours before measuring electrical properties. Meets Initial Values (As Above) before measuring electrical properties. 2.5% or .25 pF, whichever is greater Meets Initial Values (As Above) Meets Initial Values (As Above) onds. Store at room temperature for 24 2hours Meets Initial Values (As Above) Meets Initial Values (As Above) No visual defects No.25 visual 2.5% or pF,defects whichever is greater Step 1: -55C 2 30 3 minutes Step 1: -55C 2Temp Step 2: Room 3033minutes minutes Step 2: Room Temp 3 minutes Meets Initial Values (As Above) Step 3: +125C 2 30 3 minutes Meets Initial Values (As Above) Step 4: Room Temp 3 minutes 2.5% or .25 pF, whichever is greater Meets Initial Values (As Above) Meets Initial Values (As Above) Meets Initial Values (As Above) Meets Initial Values (As Above) No visual defects Novisual 3.0% or .3 pF,defects whichever is greater 3.0% or .3 pF, whichever is greater 30 pF: 10 pF, <30 pF: 30 pF: <10 pF: Q 350 Q 275 +5C/2 Q 350 Q 200 +10C 10 pF, <30 pF: Q 275 +5C/2 <10 pF: Initial Value Q 200 +10C x 0.3 (See Above) Initial Value x 0.3 (See Above) Meets Initial Values (As Above) Step 3: +125C 2 Step 4: Room Temp 30 3 minutes 3 minutes Repeat for 5 cycles and measure after 24 hours at room temperature Repeat for 5 cycles and measure after 24 hours at room temperature Charge device with twice rated voltage in test chamber set at 125C 2C Charge device with twice rated voltage in for 1000 hours (+48, -0). test chamber set at 125C 2C for 1000 hours (+48, -0). Remove from test chamber and stabilize at hours at Removeroom from temperature test chamber for and24 stabilize room temperature for 24 hours before measuring. before measuring. Meets Initial Valuesdefects (As Above) No visual 5.0% or .5 pF, whichever is greater No visual defects pF:pF, whichever Q 350 is greater 5.0%or30 .5 10 pF, <30 pF: <10 30 pF:pF: Q 275 +5C/2 Q Q 200350 +10C 10 pF, <30 pF: Q 275 +5C/2 Initial Value x 0.3 (See Above) <10 pF: Q 200 +10C Meets Initial Values Above) Initial Value x 0.3 (See(As Above) Store in a test chamber set at 85C 2C/ 85% 5% relative humidity for 1000 hours (+48, -0) with rated voltage applied. Store in a test chamber set at 85C 2C/ 85% 5% relative humidity for 1000 hours Remove fromrated chamber andapplied. stabilize at (+48, -0) with voltage room temperature for 24 2 hours before measuring. Remove from chamber and stabilize at room temperature for 24 2 hours before measuring. Meets Initial Values (As Above) 555 C0G (NP0) Dielectric Capacitance Range PREFERRED SIZES ARE SHADED SIZE 0101* Soldering Packaging Reflow Only 0201 0402 Reflow Only Reflow/Wave 0603 0805 Reflow/Wave Reflow/Wave Reflow/Wave Paper/Embossed Paper/Embossed 2.01 0.20 (0.079 0.008) 1.25 0.20 (0.049 0.008) 0.50 0.25 (0.020 0.010) 3.20 0.20 (0.126 0.008) 1.60 0.20 (0.063 0.008) (L) Length mm (in.) All Paper All Paper 0.60 0.09 0.40 0.02 (0.016 0.0008) (0.024 0.004) All Paper 1.00 0.10 (0.040 0.004) All Paper 1.60 0.15 (0.063 0.006) (W) Width mm (in.) mm (in.) 0.20 0.02 0.30 0.09 (0.008 0.0008) (0.011 0.004) 0.10 0.04 0.15 0.05 (0.004 0.0016) (0.006 0.002) 0.50 0.10 (0.020 0.004) 0.25 0.15 (0.010 0.006) 0.81 0.15 (0.032 0.006) 0.35 0.15 (0.014 0.006) (t) Terminal Cap (pF) WVDC 0.5 1.0 1.2 1.5 25 J J J J J J J 50 J J J J J J J 100 J J J J J J J 200 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J G G G G G G J J J J J J J J J J J J J J J J J J G G G G G G G G G G G G J J J J J J J J J J J J G G G G G G G G G G G G G G G G G J J J J J J G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G 1800 2200 2700 G G G G G G 3300 3900 4700 G G G G G G G G G 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 B B B B B B 25 A A A A A A A 50 A A A A A A A 16 C C C C C C C 25 C C C C C C C 50 C C C C C C C 16 G G G G G G G 25 G G G G G G G 50 G G G G G G G 100 G G G G G G G B B B B B B A A A A A A A A A A A A C C C C C C C C C C C C C C C C C C G G G G G G G G G G G G G G G G G G G G G G G G B B B B B B A A A A A A A A A A A A C C C C C C C C C C C C C C C C C C G G G G G G G G G G G G G G G G G G G G G G G G B B B B B B A A A A A A A A A A A A C C C C C C C C C C C C C C C C C C G G G G G G G G G G G G G G G G G G B A A C C C C C C C C C C C C C C C C C C G G G G G G G G G G G G C C C C C C C C C C C C C C C C C C C G G G G G G C C 180 220 270 330 390 470 560 680 820 1000 1200 1500 200 5600 6800 8200 Cap (F) 0.50 0.25 (0.020 0.010) 16 J J J J J J J 1.8 2.2 2.7 16 1206 0.010 0.012 0.015 16 J J J J J J J 25 J J J J J J J 50 J J J J J J J 100 J J J J J J J 200 J J J J J J J 500 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J N N J J J J N N J J J J N N J J J J J J J J J J J J J J J J J J J J J M P P P P P P P P P P P P P P P P P P J J J J M P P P P P P P P P P P M M P J J J J M M P M M M M M M 16 25 16 25 N N N N N N M M M P M M M M M M P M Q Q Q Q Q Q Q P 0.018 0.022 0.027 0.033 0.039 0.047 0.068 0.082 0.1 WVDC SIZE Letter Max. Thickness 16 25 0101* A 0.33 (0.013) B 0.22 (0.009) 50 16 0201 25 50 16 25 C 0.56 (0.022) E 0.71 (0.028) 50 100 200 0603 0402 G 0.90 (0.035) J 0.94 (0.037) K 1.02 (0.040) 50 100 200 50 0805 M 1.27 (0.050) N 1.40 (0.055) P 1.52 (0.060) 100 200 500 1206 Q 1.78 (0.070) X 2.29 (0.090) Y 2.54 (0.100) Z 2.79 (0.110) EMBOSSED PAPER PAPER and EMBOSSED available for 01005 6 051818 C0G (NP0) Dielectric Capacitance Range PREFERRED SIZES ARE SHADED SIZE 1210 Soldering Packaging (L) Length (W) Width (t) Terminal Cap (pF) 1812 Reflow Only Paper/Embossed 3.20 0.20 (0.126 0.008) 2.50 0.20 (0.098 0.008) 0.50 0.25 (0.020 0.010) mm (in.) mm (in.) mm (in.) WVDC 0.5 1.0 1.2 1.5 25 50 100 1825 Reflow Only All Embossed 4.50 0.30 (0.177 0.012) 3.20 0.20 (0.126 0.008) 0.61 0.36 (0.024 0.014) 200 500 25 50 100 0.018 0.022 0.027 0.033 0.039 0.047 K K K K K K K K K K K K K K P P P Q Q X X K K K K K K K K K K K M M M P P P Q Q X X N N N N N N N N N P Q Q Q Q Q Q Q X X X X 0.068 0.082 0.1 WVDC Z Z Z 25 Z Z Z 50 2220 Reflow Only 2225 Reflow Only All Embossed 4.50 0.30 (0.177 0.012) 6.40 0.40 (0.252 0.016) 0.61 0.36 (0.024 0.014) Reflow Only All Embossed 5.70 0.40 (0.225 0.016) 5.00 0.40 (0.197 0.016) 0.64 0.39 (0.025 0.015) 200 500 50 100 200 N N N N N P P P P P Q Q Q M M M M P Q Q Q Y Y M M M M X X X X X X X X X X X X X X X X X M M M M X X X X X X X X X X X X X X X M M M M M M X X X X X X X X X X X Y 50 100 All Embossed 5.72 0.25 (0.225 0.010) 6.35 0.25 (0.250 0.010) 0.64 0.39 (0.025 0.015) 200 50 100 200 M M M M M M M M M M M M M M M M M P X X X M M M M M M M M M M M M M M M M Y Y Y Y Z P P P P P P P P P P P P P P Y Y Y Y Y Y X X Z 50 Z Z Z 100 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 Cap (F) 0.010 0.012 0.015 J J J J P P P P P P P P P P P N N J J J J P P P P P P P P P P P N N 25 SIZE Letter Max. Thickness A 0.33 (0.013) 50 J J J J K K P P P P P P P P P P P P P P P P P P 100 200 500 1210 B 0.22 (0.009) C 0.56 (0.022) Y Y Z 100 200 500 50 1812 E 0.71 (0.028) PAPER 051818 J J J J J J J J J J J J J J J J J J J M M M P P P P P P N G 0.90 (0.035) J 0.94 (0.037) K 1.02 (0.040) 100 200 X X X X X X X X X X X Y Y Z Z Z 50 1825 M 1.27 (0.050) N 1.40 (0.055) P 1.52 (0.060) X X X X X X X X X X X 100 X X X X X X X X X X 200 2220 Q 1.78 (0.070) X 2.29 (0.090) 200 2225 Y 2.54 (0.100) Z 2.79 (0.110) EMBOSSED 77