HM-6642 512 x 8 CMOS PROM March 1997 Features Description * Low Power Standby and Operating Power - ICCSB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100A - ICCOP . . . . . . . . . . . . . . . . . . . . . . . . . . 20mA at 1MHz The HM-6642 is a 512 x 8 CMOS NiCr fusible link Programmable Read Only Memory in the popular 24 pin, byte wide pinout. Synchronous circuit design techniques combine with CMOS processing to give this device high speed performance with very low power dissipation. * Fast Access Time. . . . . . . . . . . . . . . . . . . . . . 120/200ns * Industry Standard Pinout On-chip address latches are provided, allowing easy interfacing with recent generation microprocessors that use multiplexed address/data bus structures, such as the 8085. The output enable controls, both active low and active high, further simplify microprocessor system interfacing by allowing output data bus control independent of the chip enable control. The data output latches allow the use of the HM-6642 in high speed pipelined architecture systems, and also in synchronous logic replacement functions. * Single 5.0V Supply * CMOS/TTL Compatible Inputs * Field Programmable * Synchronous Operation * On-Chip Address Latches * Separate Output Enable Applications for the HM-6642 CMOS PROM include low power handheld microprocessor based instrumentation and communications systems, remote data acquisition and processing systems, processor control store, and synchronous logic replacement. All bits are manufactured storing a logical "0" and can be selectively programmed for a logical "1" at any bit location. Ordering Information PACKAGE SBDIP SMD# SLIM SBDIP SMD# CLCC SMD# TEMPERATURE RANGE 120ns 200ns PKG. NO. -40oC to +85oC HM1-6642B-9 HM1-6642-9 D24.6 -55oC to +125oC 5962-8869002JA 5962-8869001JA D24.6 -40oC to +85oC HM6-6642B-9 HM6-6642-9 D24.3 -55oC to +125oC 5962-8869002LA 5962-8869001LA D24.3 HM4-6642-9 J28.A 5962-88690013A J28.A -40oC to +85oC -55oC to +125oC 5962-88690023A CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. http://www.intersil.com or 407-727-9207 | Copyright (c) Intersil Corporation 1999 6-1 File Number 3012.1 HM-6642 Pinouts HM-6642 (CLCC) TOP VIEW A7 1 24 VCC A6 A7 NC VCC A8 G1 PIN DESCRIPTION A5 HM-6642 (SBDIP) TOP VIEW A6 2 23 A8 4 3 2 1 28 27 26 A5 3 22 G1 A4 4 21 G2 A3 5 20 G3 A2 6 19 E 7 Address Inputs E Chip Enable Q Data Output A3 6 24 G3 A2 7 23 E 18 P A1 8 22 P 8 17 Q7 A0 9 21 NC VCC Power (+5V) 9 16 Q6 10 NC 10 15 Q5 20 Q7 G1, G2, G3 Output Enable 11 14 Q4 Q0 11 19 Q6 P (Note) Program Enable 14 15 16 17 18 NOTE: P should be hardwired to GND except during programming. Q5 13 Q3 12 13 Q4 12 Q1 GND A0-A8 G2 Q3 Q2 No Connect 25 NC Q1 NC 5 GND A0 Q0 DESCRIPTION A4 Q2 A1 PIN Functional Diagram A8 A A7 A6 A5 LATCHED ADDRESS REGISTER A4 A3 6 A GATED ROW DECODER 64 x 64 MATRIX 64 ALL LINES POSITIVE LOGIC - ACTIVE HIGH THREE STATE BUFFERS: OUTPUT ACTIVE A HIGH 6 8 8 8 8 8 8 8 DATA LATCHES: Q=D L HIGH Q LATCHES ON RISING EDGE OF E 8 A A2 A1 A0 LATCHED ADDRESS REGISTER 3 ADDRESS LATCHES AND GATED DECODERS: LATCH ON FALLING EDGE OF E GATE ON FALLING EDGE OF E GATED COLUMN DECODER A 3 P SHOULD BE HARDWIRED TO GND EXCEPT DURING PROGRAMMING D E 8-BIT DATA LATCH G1 G2 G3 Q0 Q1 Q2 Q3 Q4 6-2 Q5 Q6 Q7 HM-6642 Programming Introduction The HM-6642 is a 512 word by 8-bit field Programmable Read Only Memory utilizing nicrome fusible links as programmable memory elements. Selected memory locations are permanently changed from their manufactured state, of all low (VOL) to a logical high (VOH), by the controlled application of programming potentials and pulses. Careful adherence to the following programming specifications will result in high programming yield. Both high VCC (6.0V) and low VCC (4.0V) verify cycles are specified to assure the integrity of the programmed fuse. This programming specification, although complete, does not preclude rapid programming. The worst case programming time required is 37.4 seconds, and typical programming time can be approximately 4 seconds per device. Programming System Requirements 1. The power supply for the device to be programmed must be able to be set to three voltages: 4.0V, 6.0V, 12.5V. This supply must be able to supply 500mA average, and 1A dynamic, currents to the PROM during programming. The power supply rise fall times when switching between voltages must be no quicker than 1ms. 2. The address drivers must be able to supply a VIH of 4.0V and 6.0V and VIL when the system is at programming voltages. (See Note) 3. The control input buffers must be able to maintain input voltage levels of 70% and 20% VCC for VIH and VIL levels, respectively. Notice that chip enable (E) and G does not require a pull up to programming voltage levels. The program control (P) must switch from ground to VIH and from VIH to the VCC PGM level. (See Note) The chip (E) and output enable (G) are used during the programming procedure. On PROMs which have more than one output enable control G3 is to be used. The other output enables must be held in the active, or enabled, state throughout the entire programming sequence. The programmer designer is advised that all pins of the programmer's socket should be at ground potential when the PROM is inserted into the socket. VCC must be applied to the PROM before any input or output pin is allowed to rise (See Note). 4. The data input buffers must be able to sink up to 3mA from the PROM's output pins without rising more than 0.7V above ground, be able to hold the other outputs high with a current source capability of 0.5mA to 2.0mA, and not interfere with the reading and verifying of the data output of the PROM. Notice that a bit to be programmed is changed from a low state (VOL) to high (VOH) by pulling low on the output pin. A suggested implementation is open collector TTL buffers (or inverters) with 4.7k pull up resistors to VCC. (See Note) Overall Programming Procedure 1. The address of the first bit to be programmed is presented, and latched by the chip enable (E) falling edge. The output is disabled by taking the output enable G Low: The programming pin is enabled by taking (P) high. NOTE: Never allow any input or output pin to rise more than 0.3V above VCC, or fall more than 0.3V below ground. 2. VCC is raised to the programming voltage level, 12.5V. 3. All data output pins are pulled up to VCC program. Then the data output pin corresponding to the bit to be programmed is pulled low for 100ms. Only one bit should be programmed at a time. 4. The data output pin is returned to VCC, and the VCC pin is returned to 6.0V. 5. The address of the bit is again presented, and latched by a second chip enable falling edge. 6. The data outputs are enabled, and read, to verify that the bit was successfully programmed. a). If verified, the next bit to be programmed is addressed and programmed. b). If not verified, the programs verify sequence is repeated up to 8 times total. 7. After all bits to be programmed have been verified at 6.0V, the VCC is lowered to 4.0V and all bits are verified. a). If all bits verify, the device is properly programmed. b). If any bit fails to verify, the device is rejected. 6-3 HM-6642 Background Information HM-6642 Programming PROGRAMMING SPECIFICATIONS LIMITS SYMBOL MIN TYP MAX UNITS Programming VCC 12.0 12.0 12.5 V Operating VCC 4.5 5.5 5.5 V Special Verify VCC 4.0 - 6.0 V System ICC Capability 500 - - mA Transient ICC Capability 1.0 - - A VOL Output Low Voltage (To PROM) -0.3 GND 20% VCC V VOH Output High Voltage (To PROM) 70% VCC VCC VCC +0.3 V IOL Output Sink Current (At VOL) 0.01 - - mA IOH Output Source Current (At VOH) 0.01 - - mA VCC PROG VCCN VCC LV ICC ICC Peak PARAMETER PROM INPUT PINS PROM DATA OUTPUT PINS VOL Output Low Voltage (To PROM) -0.3 GND 0.7 V VOH Output High Voltage (To PROM) 70% VCC VCC VCC +0.3 V IOL Output Sink Current (At VOL) 3.0 - - mA IOH Output Source Current (At VOH) 0.5 1.0 2.0 mA tD Delay Time 1.0 1.0 - s tR Rise Time 1.0 10.0 10.0 s tF Fall Time 1.0 10.0 10.0 s TEHEL Chip Enable Pulse Width 500 - - ns TAVEL Address Valid to Chip Enable Low Time 500 - - ns TELQV Chip Enable Low to Output Valid Time - - 500 ns tpw Programming Pulse Width 90 100 110 s tIP Input Leakage at VCC = VCC PROG -10 +1.0 10 A TA Ambient Temperature - 25 - oC 6-4 HM-6642 PROGRAMMING VCC PROG VIH VIL A VERIFY VALID VALID tD TEHEL VIH E VIL tD tD G VCC PROG VIH VIL P VCC PROG VIH VIL VCC VCC PROG VCC GND Q VCC PROG VIH/VOH VIL/VOL tD tD tR tD tPW tD tF READ DATA FIGURE 1. HM-6642 PROGRAMMING CYCLE A VIH VALID VIL TAVEL E TEHEL TEHEL VIH VIL tD TEHEL tD 6.0V 5.0V 4.0V VCC 0.0V TELQV Q VOH VOL TELQV READ TELQV READ FIGURE 2. HM-6642 POST PROGRAMMING VERIFY CYCLE 6-5 READ HM-6642 Absolute Maximum Ratings Thermal Information Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7.0V Input, Output or I/O Voltage . . . . . . . . . . . GND -0.3V to VCC +0.3V Typical Derating Factor . . . . . . . . . . . . 5mA/MHz Increase in ICCOP ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1 Thermal Resistance JA JC SBDIP Package . . . . . . . . . . . . . . . . . . 52oC/W 14oC/W Slim SBDIP . . . . . . . . . . . . . . . . . . . . . 70oC/W 19oC/W CLCC Package . . . . . . . . . . . . . . . . . . 58oC/W 14oC/W Maximum Storage Temperature Range . . . . . . . . .-65oC to +150oC Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +175oC Maximum Lead Temperature (Soldering 10s)+300oC Operating Conditions Operating Voltage Range . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V Operating Temperature Range HM-6642B-9, HM-6642-9 . . . . . . . . . . . . . . . . . . . -40oC to +85oC Die Characteristics Gate Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1680 Gates CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. DC Electrical Specifications VCC = 5V 10%; TA = -40oC to +85oC (HM-6642B-9, HM-6642-9) LIMITS SYMBOL PARAMETER MIN MAX UNITS TEST CONDITIONS ICCSB Standby Supply Current - 100 A IO = 0, VI = VCC or GND, VCC = 5.5V ICCOP Operating Supply Current (Note 3) - 20 mA f = 1MHz, IO = 0, VI = VCC or GND, VCC = 5.5V Input Leakage Current -1.0 +1.0 A GND VI VCC, VCC = 5.5V IOZ Output Leakage Current -1.0 +1.0 A GND VO VCC, VCC = 5.5V VIL Input Low Voltage -0.3 0.8 V VCC = 4.5V VIH Input High Voltage 2.4 VCC + 0.3 V VCC = 5.5V VOL Output Low Voltage - 0.4 V IOL = 3.2mA, VCC = 4.5V VOH1 Output High Voltage 2.4 - V IOH = -1.0mA, VCC = 4.5V VOH2 Output High Voltage (Note 2) VCC - 1.0 - V IOH = -100A, VCC = 4.5V II AC Electrical Specifications LIMITS HM-6642B-9 SYMBOL PARAMETER HM-6642-9 MIN MAX MIN MAX UNITS TEST CONDITIONS (1) TELQV Chip Enable Access Time - 120 - 200 ns Notes 1, 4 (2) TAVQV Address Access Time (TAVQV = TELQV + TAVEL) - 140 - 220 ns Notes 1, 4 (3) TGVQV Output Enable Access Time - 50 - 150 ns Notes 1, 4 (4) TGVQX Output Enable Time 5 50 5 150 ns Notes 2, 4 (5) TGXQZ Output Disable Time - 50 - 150 ns Notes 2, 4 (6) TELEH Chip Enable Pulse Negative Width 120 - 200 - ns Notes 1, 4 (7) TELEL Read Cycle Time 160 - 350 - ns Notes 1, 4 (8) TEHEL Chip Enable Pulse Positive Width 40 - 150 - ns Notes 1, 4 (9) TAVEL Address Setup Time 20 - 20 - ns Notes 1, 4 (10) TELAX Address Hold Time 25 - 60 - ns Notes 1, 4 6-6 HM-6642 Capacitance TA = +25oC LIMITS SYMBOL PARAMETER MIN MAX UNITS CI Input Capacitance (Note 2) - 10.0 pF CO Output Capacitance (Note 2) - 12.0 pF TEST CONDITIONS f = 1MHz, All Measurements Reference Device Ground NOTES: 1. Input pulse levels: 0 to 3.0V; Input rise and fall times: 5ns (max); Input and output timing reference level: 1.5V; Output load: 1 TTL gate equivalent CL = 50pF (min) - for CL greater than 50pF, access time is derated by 0.15ns per pF. 2. Tested at initial design and after major design changes. 3. Typical derating 5mA/MHz increase in ICCOP. 4. VCC = 4.5V and 5.5V. Switching Waveform (2) TAVQV (9) TAVEL TELAX (10) A TAVEL (9) NEXT ADD ADD VALID TELEL (7) (8) TEHEL TELEH (6) TEHEL (8) E TELQV (1) DATA VALID Q TGVQX (4) TGXQZ (5) TGXQZ (5) TGVQV (3) G (NOTE) TIME REFERENCE -1 0 1 2 3 456 NOTE: G has the same timing as G except signal is inverted. FIGURE 3. READ CYCLE Test Load Circuit DUT CL (NOTE) IOH NOTE: TEST HEAD CAPACITANCE, INCLUDES STRAY AND JIG CAPACITANCE 1.5V EQUIVALENT CIRCUIT 6-7 IOL HM-6642 All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com Sales Office Headquarters NORTH AMERICA Intersil Corporation P. O. Box 883, Mail Stop 53-204 Melbourne, FL 32902 TEL: (407) 724-7000 FAX: (407) 724-7240 EUROPE Intersil SA Mercure Center 100, Rue de la Fusee 1130 Brussels, Belgium TEL: (32) 2.724.2111 FAX: (32) 2.724.22.05 6-8 ASIA Intersil (Taiwan) Ltd. Taiwan Limited 7F-6, No. 101 Fu Hsing North Road Taipei, Taiwan Republic of China TEL: (886) 2 2716 9310 FAX: (886) 2 2715 3029