UMFT120DC - FTDI - Datasheet.Live

Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees

to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting

from such use.

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

Future Technology

Devices

International Ltd

Datasheet

FT12 Series Evaluation Kit

Generic USB device development kit

1 Introduction

The FT12 series evaluation kit is used to develop

and demonstrate functions of FTDI’s FT120, FT121

and FT122 ICs. The kit consists of a main board

and one of the FT120/FT121/FT122 add-on

modules. These modules can provide a generic

USB device function to a microcontroller(MCU)

with the following interfaces:

- UMFT120DC: 8-bit 8051 interface, up to 3 bi-

directional endpoints

- UMFT121DC: SPI slave interface, up to 8 bi-

directional endpoints

- UMFT122DC: 8-bit 8051 interface, up to 8 bi-

directional endpoints

1.1 Features

- Micro-B USB connector to connect to

USB host or Charger port

- Allow bus-power or self-power

configuration

- LPC1114 Cortex-M0 microcontroller for

easy software development

- Pushbutton and LEDs for HID

application

- In-system firmware upgradable

- On-board prototype area for application

development

2 Ordering Information

Part No *

Description

UMFT12XEV

Main board for evaluating FT120, FT121 and FT122 add-on modules. Fitted

with LPC1114 Cortex-M0 MCU. Firmware upgradable with UART or SWD

interface. Note: Board is shipped with firmware to support CDC class devices

pre-loaded

UMFT120DC

FT120 add-on module. 8-bit 8051 parallel bus. 3 bi-directional endpoints. I/O

level 3.3V (5V tolerant). Compatible to PDIUSBD12.

UMFT121DC

FT121 add-on module. SPI slave bus. 8 bi-directional endpoints. I/O level

1.8/2.5/3.3V.

UMFT122DC

FT122 add-on module. 8-bit 8051 parallel bus. 8 bi-directional endpoints. I/O

level 1.8/2.5/3.3V.

* Note that PCB label may differ

Table 2-1 Ordering information

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

Table of Contents

1 Introduction ................................................................................... 1

1.1 Features ........................................................................................................ 1

2 Ordering Information ..................................................................... 1

3 Hardware description ..................................................................... 3

3.1 UMFT12XEV Main Board ................................................................................ 3

3.2 UMFT120DC daughter board.......................................................................... 4

3.3 UMFT121DC daughter board.......................................................................... 6

3.4 UMFT122DC daughter board.......................................................................... 7

3.5 Accessories ................................................................................................... 8

4 Initial Board Set-up ...................................................................... 10

4.1 Installing UMFT12xDC daughter board ........................................................ 10

4.2 Set the jumpers........................................................................................... 10

4.3 Install the driver ......................................................................................... 11

5 Running demo tests ...................................................................... 16

5.1 Serial Loopback test .................................................................................... 16

5.2 USB Charger test ......................................................................................... 16

6 Board Circuit Schematics and BOMs ............................................. 18

6.1 UMFT12XEV Schematic and BOM ................................................................. 18

6.2 UMFT120DC Schematic and BOM ................................................................. 19

6.3 UMFT121DC Schematic and BOM ................................................................. 20

6.4 UMFT122DC Schematic and BOM ................................................................. 21

7 Firmware Upgrade Process ........................................................... 23

7.1 Put LPC1114 microcontroller in ISP mode ................................................... 23

7.2 Connect the TTL-232R-3V3 cable ................................................................ 23

7.3 Upgrade firmware ....................................................................................... 24

8 Environmental Compliances ......................................................... 25

9 Contact Information ..................................................................... 26

Appendix A - List of Figures and Tables ................................................................. 27

Appendix B – Abbreviations and References ......................................................... 29

Appendix C - Revision History ............................................................................... 30

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

3 Hardware description

3.1 UMFT12XEV Main Board

The UMFT12XEV board is intended for use as a hardware platform to enable easy evaluation of FTDI’s

FT120, FT121 and FT122 series of USB peripheral controllers. The UMFT12XEV boards utilize a NXP

Cortex-M0 based microcontroller (LPC1114) to interface to FT12 series with parallel or SPI bus. The LEDs

and push buttons can be used to demo the HID keyboard functions. A prototype area is also built on the

UMFT12XEV board, allowing user defined application circuit to be added so that application

hardware/firmware can be developed and tested on the prototype before porting over to mass

production.

Figure 3-1 shows the PCB layout with main component positions. These components include:

- 14x2 socket for add-on module: insert any of the three daughter boards (UMFT120DC,

UMFT121DC, UMFT122DC)

- 3.3V Regulator: It takes 5V input from USB Vbus (bus-power) or DC jack CN4 (self power) and

output 3.3V for on-board circuits

- LED(GPIO): 2 LED diodes for GPIO status display. Can be used for HID keyboard status LED

- LED(BCD_DET): This LED indicates if a USB Charger is attached and detected by FT121/FT122

- Push Button(GPIO): 2 push buttons for GPIO control input. Can be used for HID keyboard

function keys

- Reset button: hardware reset button

- UART connector: This 6-pin UART connector can be used for in-system firmware download as well

as firmware debug port

- SPI0 connector: This 6-pin SPI connector can be used to connect to a SPI slave board

- JTAG/SWD connector: This 8-pin connector is for connecting to LPC-link for firmware download or

debug purpose

- LPC1114 Microcontroller: 44-pin LPC1114 Cortex-M0 MCU to control FT12x and other peripherals

- Prototype area: for adding extra application circuits for prototyping purpose

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

Figure 3-1 UMFT12XEV main board

3.2 UMFT120DC daughter board

Figure 3-2 UMFT120DC daughter board

PIN No.

PIN NAME

TYPE

DESCRIPTION

1

D0

IO

Data bus bit 0.

2

D1

IO

Data bus bit 1.

3

D2

IO

Data bus bit 2.

4

D3

IO

Data bus bit 3.

5

NC

-

No Connection

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

PIN No.

PIN NAME

TYPE

DESCRIPTION

6

GND

P

Ground

7

D4

IO

Data bus bit 4.

8

D5

IO

Data bus bit 5.

9

D6

IO

Data bus bit 6.

10

D7

IO

Data bus bit 7.

11

ALE

I

Address latch enable for multiplexed address/data bus

configuration.

This pin must be pulled Low for non-multiplexed address/data

bus configuration.

12

CS_n

I

Chip select (Active Low).

13

GND

P

Ground

14

CLKOUT

O

Programmable output clock.

15

RD_n

I

Read enable (Active Low).

16

WR_n

I

Write enable (Active Low).

17

DMREQ

O

DMA request.

18

DMACK_n

I

DMA acknowledge (Active Low).

19

EOT_n

I

End of DMA transfer (Active Low). Also function as Vbus

sensing input for self-powered application.

20

GL_n

OD

USB bus activity indicator (Active Low)

21

A0

I

Address bit for non-multiplexed address/data bus configuration.

- A0=1 indicates command phase;

- A0=0 indicates data phase.

This pin must be pulled High for multiplexed address/data bus

configuration.

22

SUSPEND

I,OD

Device suspend (output) and wakeup (input).

23

INT_n

OD

Interrupt (Active Low).

24

RESET_n

I

Asynchronous reset (Active Low).

25

NC

-

No Connection

26

VOUT3V3

P

3.3V regulator output

27

VBUS

P

5V VBUS power from USB connector

28

VCC

P

VCC power supply

Table 3-1 UMFT120DC J1 Pin Out Description

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

3.3 UMFT121DC daughter board

Figure 3-3 UMFT121DC daughter board

PIN No.

PIN NAME

TYPE

DESCRIPTION

1

SS_n

I

SPI slave select input.

2

SCLK

I

SPI clock input.

3

MISO

O

4-wire mode: SPI slave output.

3-wire mode: no function. Leave it un-connected.

4

MOSI

I/IO

4-wire mode: SPI salve input

3-wire mode: SPI data input/output

5

VCCIO

P

IO Supply Voltage; 1.8V, 2.5V or 3.3V

6

GND

P

Ground

7

NC

-

No Connection

8

SUSPEND

I,OD

Device suspend (output) and wakeup (input).

9

INT_n

OD

Interrupt (Active Low).

10

RESET_n

I

Asynchronous reset (Active Low).

11

BCD_n

OD

USB Charger detector output

12

VOUT3V3

P

3.3V regulator output

13

VBUS

P

5V VBUS power from USB connector

14

VCC

P

VCC power supply

Table 3-2 UMFT121DC J1 Pin Out Description

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

3.4 UMFT122DC daughter board

Figure 3-4 UMFT122DC daughter board

PIN No.

PIN NAME

TYPE

DESCRIPTION

1

D0

IO

Data bus bit 0.

2

D1

IO

Data bus bit 1.

3

D2

IO

Data bus bit 2.

4

D3

IO

Data bus bit 3.

5

VCCIO

P

IO Supply Voltage; 1.8V, 2.5V or 3.3V

6

GND

P

Ground

7

D4

IO

Data bus bit 4.

8

D5

IO

Data bus bit 5.

9

D6

IO

Data bus bit 6.

10

D7

IO

Data bus bit 7.

11

ALE

I

Address latch enable for multiplexed address/data bus

configuration.

This pin must be pulled Low for non-multiplexed address/data

bus configuration.

12

CS_n

I

Chip select (Active Low).

13

GND

P

Ground

14

CLKOUT

O

Programmable output clock.

15

RD_n

I

Read enable (Active Low).

16

WR_n

I

Write enable (Active Low).

17

DMREQ

O

DMA request.

18

DMACK_n

I

DMA acknowledge (Active Low).

19

EOT_n

I

End of DMA transfer (Active Low). Also function as Vbus

sensing input for self-powered application.

20

GL_n

OD

USB bus activity indicator (Active Low)

21

A0

I

Address bit for non-multiplexed address/data bus configuration.

- A0=1 indicates command phase;

- A0=0 indicates data phase.

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

PIN No.

PIN NAME

TYPE

DESCRIPTION

This pin must be pulled High for multiplexed address/data bus

configuration.

22

SUSPEND

I,OD

Device suspend (output) and wakeup (input).

23

INT_n

OD

Interrupt (Active Low).

24

RESET_n

I

Asynchronous reset (Active Low).

25

BCD_n

OD

USB Charger detector output

26

VOUT3V3

P

3.3V regulator output

27

VBUS

P

5V VBUS power from USB connector

28

VCC

P

VCC power supply

Table 3-3 UMFT122DC J1 Pin Out Description

3.5 Accessories

Accessories that might be useful for the FT12x Evaluation kit demo and firmware upgrade/debug:

a) Micro-B to Standard-A USB cable: for connecting the FT12x evaluation kit to PC host or USB

charger port

Figure 3-5 Micro-B to Standard-A cable

b) TTL-232R-3V3 USB cable (optional): for firmware upgrade. For more info please refer to

http://www.ftdichip.com/Products/Cables/USBTTLSerial.htm. Can be purchased from FTDI online

shop ( http://apple.clickandbuild.com/cnb/shop/ftdichip?productID=53&op=catalogue-

product_info-null&prodCategoryID=105 ).

Figure 3-6 TTL-232R-3V3 USB cable

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

c) LPC-Link JTAG/SWD debugger module (optional): for firmware download and debug. For more

info refer to http://ics.nxp.com/lpcxpresso/ .

Figure 3-7 LPC-Link debugger module

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

4 Initial Board Set-up

4.1 Installing UMFT12xDC daughter board

Insert the daughter board module (UMFT120DC, UMFT121DC or UMFT122DC) into the UMFT12XEV main

board. Pin 1 of daughter board connector J1 shall plug into pin 1 of the socket J2 on the main board.

After connection the micro-USB connector on the UMFT12xDC module should be facing outside.

Figure 4-1 Plug the daughter board module to the main board

4.2 Set the jumpers

On the main board JP2, JP3 and JP4 need to be set to the default location as indicated in Table

4-1.

header

Jumper Pin position

Comment

JP2

Short pin 1-2 (default)

Short pin 2-3

VCC=5V

VCC=3.3V

JP3

Short pin 1-2 (default)

Short pin 2-3

Bus power

Self power, a 5V DC power shall be applied to DC jack CN4

JP4

Short pin 1-2 (default)

Short pin 2-3

External 3.3V regulator for on-board circuits

FT12x built-in 3.3V regulator for on-board circuits

Table 4-1 Default setting of the jumpers

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

Figure 4-2 JP2 default setting

Figure 4-3 JP3 and JP4 default setting

4.3 Install the driver

The LPC1114 on the UMFT12XEV board is pre-loaded with firmware supporting Communication Device

Class (CDC class). The major OSs support the CDC protocol on their USB stack to use serial port

communication, allowing PC’s to access the CDC device through a virtual COM port (VCP) without

developing a new driver.

Linux recognize the CDC device as /dev/ttyACM# (# denotes a number). The driver is loaded

automatically when the device is connected.

Mac OS recognize the CDC device as /dev/cu.usbmodem# (# denotes a number). The driver is loaded

automatically when the device is connected.

Windows has a CDC protocol driver (usbser.sys) to generate VCP. However, it requires a “Setting

Information (INF)” file at the first connection. The required INF file can be download from FTDI website

http://www.ftdichip.com/Products/Modules/DevelopmentModules.htm.

Here is an example of driver installation under Windows 7 32-bit system:

 Connect the daughter card USB connector to the test PC with the micro-USB-B to Standard-A cable

 On Windows 7 PC, open control panel->device manager

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

Figure 4-4 Device manager window

 Right click on “FT12X Evaluation Platform” under “Other devices” category, select “Property”

Figure 4-5 Drive property window

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

 Click “Update Driver…”

Figure 4-6 Update driver window

 Click “Browse my computer for driver software”

Figure 4-7 Update driver window

 Click “Let me pick from a list of device drivers on my computer”

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

Figure 4-8 Update driver window

 Click “Next”

Figure 4-9 Update driver window

 Click “Have Disk…”

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

Figure 4-10 Install from disk window

 Click “Browse…”, select the downloaded “FT12x.inf” file to load “usbser.sys” driver. Click “OK” and

then “”Next”.

 The driver installation started. When completed, the below window is displayed. A COM port number

(COM25 in this example) will be assigned to the FT12x CDC interface. Write down this port number

as it will be required by the serial loopback test utility. Click “Close” to finish the driver installation.

Figure 4-11 Update driver complete window

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

5 Running demo tests

The UMFT12XEV is pre-loaded with a default firmware. The firmware can auto-detect the daughter card

type, and the LPC1114 MCU can communicate to the FT12 series with either SPI(for FT121) or parallel

(for FT120 or FT122) protocol. For bus-powered configuration (default setting), the FT12x evaluation kit

will power on when the USB cable is plugged in. LED D4 (red) on the main board will be ON, indicating

the 3.3V power is ready. The D2 and D3 LEDs (red) will be flashing, indicating the firmware is up and

running. For UMFT120DC and UMFT122DC, the LED D1 (green) on the daughter card will be tunred ON

upon successful enumeration, and blinking when there are USB transactions.

The default firmware supports USB CDC class driver. Upon enumeration a virtual COM port is present on

the PC. User can run serial port applications such as serial loopback test, teraterm, hyperterm etc.

5.1 Serial Loopback test

Follow the steps below to run the serial loopback test over the FT12x USB serial port interface.

- Install the serial loopback test utility. Download v1.10 of the serial loopback test utility at

http://www.madsencircuits.com/serial_loopback.html .

- Start the loopback test by clicking All Programs -> Serial Loopback Test -> Serial Loopback

Test.

- Select the Serial Port number from the pull-down list. In this example COM25 is selected.

- Click “Start Test” button. The utility will send data to the FT12x USB serial port, receive

back from the same serial port, and perform the comparisson of the received data from the

sent one. The FT12x Evaluation kit firmware will route all the received data back to the PC

internally (the firmware will store the data from bulk OUT endpoint, and send it back when

the bulk IN token comes).

Figure 5-1 Serial Loopback Test

5.2 USB Charger test

The FT121 and FT122 supports USB Charger (Wall Charger or Dedicated Charging Port) detection. The

USB Charger shall have micro-B plug with its D+/D- pins shorted.

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

Follow the steps below to check the USB Charger detection function:

- Connect the USB Charger to the micro-B USB connector of UMFT121DC or UMFT122DC

module.

- Plug the USB Charger to the Wall power socket and switch on the power.

- The yellow LED (D1 on the UMFT12XEV main board) will be turned ON. This indicates a

USB wall charger or dedicated charging port is connected.

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

6 Board Circuit Schematics and BOMs

6.1 UMFT12XEV Schematic and BOM

Figure 6-1 UMFT12XEV Circuit Schematic

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

#

Designator

Comment

Description

ManufacturerPartNo

Manufacturer

1

CN4

Power Jack

Low Voltage Power

Supply Connector

PJ-002A

CUI Inc

2

XL1, XL2, XL3

Jumper 2.54mm

2.54mm Shorting

Jumper

969102-0000-DA

3M

3

R2, R3

0R

Resistor

RC0603JR-070RL

Yageo

4

R10

1k

Resistor

RC0603JR-071KL

Yageo

5

R13

1M

Resistor

RC0603FR-071ML

Yageo

6

R5, R6

4k7

Resistor

RC0603FR-074K7L

Yageo

7

R7, R11, R12

10K

Resistor

RC0603FR-0710KL

Yageo

8

R4, R8, R9,

R14

470R

Resistor

RC0603FR-07470RL

Yageo

9

C4, C7, C11

10nf

CAP CER 10000PF

50V 10% X7R 0603

C0603C103K5RACTU

Kemet

10

C3, C5, C6,

C10

0.1uF

Capacitor bipolar

06035C104KAT2A,

C0603C104K8RACTU

AVX Corporation,

Kemet

11

SW1, SW2,

SW3

SW_PB_4PIN

Push button

momentary switch

FSM4JH

TE Connectivity

12

C1, C2

27pf

Capacitor bipolar

06035A270JAT2A,

06035C180JAT2A

AVX Corporation

13

C8, C9

4.7uF

CAP TANTALUM

4.7UF 6.3V 20%

SMD

TAJA475M006RNJ

AVX Corporation

14

'JP2, JP3, JP4

'SIP-3

'3 contact jumper

'TSW-103-07-T-S

'Samtec Inc

15

U1

IC_LPC1114_QFP48

LPC1114FBD48/302,1

NXP

Semiconductors

16

CN2

Male Header 6-pin

CONN HEADER

6POS .100 STR

15AU

68000-206HLF

FCI

17

D2, D3, D4

Red

Typical LED diode

APT2012EC

Kingbright Corp

18

D1

Yellow

Typical LED diode

APT2012SYCK

Kingbright Corp

19

J2

Two 14 pin Female

Header pitch 2.54mm

Board to Board /

Mezzanine

Connectors

RECEPTACLE 14P

68685-314LF

FCI

20

U2

IC_AIC1733

500mA, Low

Dropout Linear

Regulator with

Shutdown

AIC1733-33PV

AIC

21

CN3

2X3 Pin Header (Male)

CONN HEADER

6POS .100" DUAL

TIN

TSW-103-07-T-D

Samtec Inc

22

CN1

Male Header 8-pin

CONN HEADER

8POS .100" SNGL

TIN

TSW-108-07-T-S

Samtec Inc

23

Y1

12MHz

ECS-120-18-4XEN

ECS Inc

Table 6-1 UMFT12XEV BOM list

Note: J1 not mounted.

6.2 UMFT120DC Schematic and BOM

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

Figure 6-2 UMFT120DC Circuit Schematic

#

Designator

Comment

Description

ManufacturerPartNo

Manufacturer

1

U1

FT120T

FT120 USB device

controller with parallel

interface, TSSOP-28

FT120T

FTDI Chip

2

CN1

MicroUSB

CONN RCPT STD MICRO

USB TYPE B

10104110-0001LF

FCI

3

R1, R2

27R/1%

Resistor

RC0603FR-0727RL

Yageo

4

R3

0R

Resistor

RC0603FR-07000RL

Yageo

5

R4

470R

Resistor

RC0603FR-07470RL

Yageo

6

C2

10nf

CAP CER 10000PF 50V

10% X7R 0603

C0603C103K5RACTU

Kemet

7

FB1

600R/0.5A

Chip Ferrite Bead 0805

MPZ1608S601A

TDK Corporation

8

C5, C6

27pf

Capacitor bipolar

06035A270JAT2A

AVX Corporation

9

C4

4.7uF

Polarized Capacitor

TAJA475K016RNJ

AVX Corporation

10

C1, C3

0.1uF

Capacitor bipolar

06035C104KAT2A

AVX Corporation

11

D1

Green

Typical LED diode

APT2012SGC

Kingbright Corp

12

J1

Two 1X14 PIN

HEADER, 600mil

spacing

'Headers & Wire Housings

14P SR UNSHRD HRD .76

GOLD OVER NI

68000-114HLF

FCI

13

Y1

6MHz

6.0MHZ CRYSTAL

ECS-60-18-4XEN

ECS Inc

Table 6-2 UMFT120DC BOM list

6.3 UMFT121DC Schematic and BOM

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

Figure 6-3 UMFT121DC Circuit Schematic

#

Designator

Comment

Description

ManufacturerPartNo

Manufacturer

1

U1

FT121T

FT121 USB device

controller with SPI slave,

TSSOP-16

FT121T

FTDI Chip

2

CN1

MicroUSB

CONN RCPT STD MICRO

USB TYPE B

10104110-0001LF

FCI

3

R3, R4

27R/1%

Resistor

RC0603FR-0727RL

Yageo

4

R2

100k

Resistor

RC0603JR-07100KL

Yageo

5

R1

200k

Resistor

RC0603JR-07200KL

Yageo

6

R5

0R

Resistor

RC0603FR-07000RL

Yageo

7

C3

10nf

CAP CER 10000PF 50V

10% X7R 0603

C0603C103K5RACTU

Kemet

8

FB1

600R/0.5A

Chip Ferrite Bead 0805

MPZ1608S601A

TDK Corporation

9

C2

4.7uF

Polarized Capacitor

TAJA475K016RNJ

AVX Corporation

10

C1, C4, C5

0.1uF

Capacitor bipolar

06035C104KAT2A

AVX Corporation

11

J1

Two 1X7 PIN

HEADER, 600mil

spacing

'Headers & Wire Housings

7P SR UNSHRD HRD .76

GOLD OVER NI

68000-107HLF

FCI

Table 6-3 UMFT121DC BOM list

6.4 UMFT122DC Schematic and BOM

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

Figure 6-4 UMFT122DC Circuit Schematic

#

Designator

Comment

Description

ManufacturerPartNo

Manufacturer

1

U1

FT122T

Enhanced USB device

controller with parallel

interface, TSSOP-28

FT122T

FTDI Chip

2

CN1

MicroUSB

CONN RCPT STD MICRO

USB TYPE B

10104110-0001LF

FCI

3

R2, R3

27R/1%

Resistor

RC0603FR-0727RL

Yageo

4

R4

0R

Resistor

RC0603FR-07000RL

Yageo

5

R1

470R

Resistor

RC0603FR-07470RL

Yageo

6

C2

10nf

CAP CER 10000PF 50V

10% X7R 0603

C0603C103K5RACTU

Kemet

7

FB1

600R/0.5A

Chip Ferrite Bead 0805

MPZ1608S601A

TDK Corporation

8

C1

4.7uF

Polarized Capacitor

TAJA475K016RNJ

AVX Corporation

9

C3, C4, C5

0.1uF

Capacitor bipolar

06035C104KAT2A

AVX Corporation

10

D1

Green

Typical LED diode

APT2012SGC

Kingbright Corp

11

J1

Two 1X14 PIN

HEADER, 600mil

spacing

'Headers & Wire Housings

14P SR UNSHRD HRD .76

GOLD OVER NI

68000-114HLF

FCI

Table 6-4 UMFT122DC BOM list

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

7 Firmware Upgrade Process

The firmware for the on-board microcontroller LPC1114 can be upgraded through either UART (ISP mode)

or JTAG/SWD interface. This section will describe the steps on how to download the firmware through

ISP mode. For the usage of JTAG/SWD interface with LPC-Link debug module, please refer to NXP

LPCXpresso homepage at http://ics.nxp.com/lpcxpresso/. Note that the LPCXpresso is an integrated

development platform for firmware development, debug and download for NXP’s ARM-based LPC

microcontrollers. The LPCXpresso development tool chain can be downloaded from

http://lpcxpresso.code-red-tech.com/LPCXpresso/ .

Check the FTDI website for the available pre-compiled firmware for FT12x Evaluation Kit (

http://www.ftdichip.com/Firmware/Precompiled.htm ).

7.1 Put LPC1114 microcontroller in ISP mode

- Use a jumper wire to short pad 38 of J1 to pad 1 or pad 54 of J1. This is to connect the LPC1114

P0_1 pin to GND so that LPC1114 will enter ISP mode after power on or reset.

- Connect the board to the test PC via the micro-USB cable. The USB–A plug shall be inserted in

the PC USB port, while the micro-USB-B plug shall be connected to the daughter card USB port.

The board will be powered on with the LPC1114 entering ISP mode. Note for self power

configuration the daughter card is not required to be present for firmware upgrading. For bus

power configuration the daughter card is required as the power comes from the daughter card

USB port.

Figure 7-1 Plug in micro USB cable

7.2 Connect the TTL-232R-3V3 cable

- Connect the board to the test PC using a TTL-232R-3V3 cable. Plug the 6-pin socket of the cable

into the CN2 pin header. Please note the direction of the cable, the black wire (GND) should be

plugged in to pin 1 of CN2.

- Connect the other end of the TTL-232R-3V3 cable to a USB port of the test PC

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

Figure 7-2 Connect TTL-232R-3V3 UART cable

7.3 Upgrade firmware

- Download and install the driver for the FTDI TTL-232R-3V3 cable. Refer to the cable datasheet for

details ( http://www.ftdichip.com/Support/Documents/DataSheets/Cables/DS_TTL-

232R_CABLES.pdf )

- Download the Flash Magic firmware programming utility from http://www.flashmagictool.com.

- Install the utility on test PC by running “FlashMagic.exe”

- Once installation is complete, launch the utility from Start -> All Programs -> Flash Magic ->

Flash Magic.

- Configure the tool by the following steps:

o Click “Select Device…”, choose LPC1114/302 from the popup window and click OK

o COM port: select the COM port number associated with the TTL-232R-3V3 cable. The

COM port number can be found in the “Device Manager -> Ports (COM & LPT) -> USB

Serial Port (COM3)”. Note on different PC this number can be changed.

o Interface: select “FTDI USB-Dongle” from the pull-down list.

o Oscillator (MHz): key in ‘12’.

o Tick the box “Erase blocks used by Hex File”.

o Select Hex File: browse to select the desired firmware binary hex file (ie “LPC1114-

FT12x.hex”).

o Tick the box “Verify after programming”

o The tool is configured ready for firmware downloading.

- Click “Start” button and the firmware download will begin. Typically the download takes about 2

minutes. Once completed, a ‘finished’ message will be displayed in the status bar (bottom side),

and the green download progress bar will reach 100%. Note the ‘finished’ message may

disappear after a while. If no message is displayed in the status bar after a few minutes, this also

indicates that the previous download is completed.

- Power off the board. Remove the ISP jumper wire and then power on the board again. The new

firmware will take effect.

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

Figure 7-3 Flash Magic configuration

8 Environmental Compliances

The UMFT12XEV main board and UMFT12XDC daughter boards exclusively use lead free components, and

are fully compliant with European Union directive 2002/95/EC.

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

9 Contact Information

Head Office – Glasgow, UK

Future Technology Devices International Limited

Unit 1, 2 Seaward Place, Centurion Business Park

Glasgow G41 1HH

United Kingdom

Tel: +44 (0) 141 429 2777

Fax: +44 (0) 141 429 2758

E-mail (Sales)

sales1@ftdichip.com

E-mail (Support)

support1@ftdichip.com

E-mail (General Enquiries)

admin1@ftdichip.com

Branch Office – Taipei, Taiwan

Future Technology Devices International Limited (Taiwan)

2F, No. 516, Sec. 1, NeiHu Road

Taipei 114

Taiwan , R.O.C.

Tel: +886 (0) 2 8791 3570

Fax: +886 (0) 2 8791 3576

E-mail (Sales)

tw.sales1@ftdichip.com

E-mail (Support)

tw.support1@ftdichip.com

E-mail (General Enquiries)

tw.admin1@ftdichip.com

Branch Office – Hillsboro, Oregon, USA

Future Technology Devices International Limited (USA)

7130 SW Fir Loop

Tigard, OR 97223

USA

Tel: +1 (503) 547 0988

Fax: +1 (503) 547 0987

E-Mail (Sales)

us.sales@ftdichip.com

E-Mail (Support)

us.support@ftdichip.com

E-Mail (General Enquiries)

us.admin@ftdichip.com

Branch Office – Shanghai, China

Future Technology Devices International Limited (China)

Room 1103, No. 666 West Huaihai Road,

Shanghai, 200052

China

Tel: +86 (0)21 6235 1596

Fax: +86 (0)21 6235 1595

E-mail (Sales)

cn.sales@ftdichip.com

E-mail (Support)

cn.support@ftdichip.com

E-mail (General Enquiries)

cn.admin@ftdichip.com

Web Site

http://ftdichip.com

Distributor and Sales Representatives

Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales

representative(s) in your country.

System and equipment manufacturers and designers are responsible to ensure that their systems, and any Future Technology Devices International Ltd

(FTDI) devices incorporated in their systems, meet all applicable safety, regulatory and system-level performance requirements. All application-related

information in this document (including application descriptions, suggested FTDI devices and other materials) is provided for reference only. While FTDI

has taken care to assure it is accurate, this information is subject to customer confirmation, and FTDI disclaims all liability for system designs and for any

applications assistance provided by FTDI. Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to

defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. This document is subject to change

without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Neither the whole nor any part

of the information contained in, or the product described in this document, may be adapted or reproduced in any material or electronic form without the prior

written consent of the copyright holder. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41

1HH, United Kingdom. Scotland Registered Company Number: SC136640

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

Appendix A - List of Figures and Tables

List of Figures

Figure 3-1 UMFT12XEV main board ............................................................................................................... 4

Figure 3-2 UMFT120DC daughter board ........................................................................................................ 4

Figure 3-3 UMFT121DC daughter board ........................................................................................................ 6

Figure 3-4 UMFT122DC daughter board ........................................................................................................ 7

Figure 3-5 Micro-B to Standard-A cable ........................................................................................................ 8

Figure 3-6 TTL-232R-3V3 USB cable .............................................................................................................. 8

Figure 3-7 LPC-Link debugger module ......................................................................................................... 9

Figure 4-1 Plug the daughter board module to the main board................................................................ 10

Figure 4-2 JP2 default setting ...................................................................................................................... 11

Figure 4-3 JP3 and JP4 default setting........................................................................................................ 11

Figure 4-4 Device manager window ............................................................................................................. 12

Figure 4-5 Drive property window ................................................................................................................ 12

Figure 4-6 Update driver window ................................................................................................................. 13

Figure 4-7 Update driver window ................................................................................................................. 13

Figure 4-8 Update driver window ................................................................................................................. 14

Figure 4-9 Update driver window ................................................................................................................. 14

Figure 4-10 Install from disk window ........................................................................................................... 15

Figure 5-1 Serial Loopback Test .................................................................................................................. 16

Figure 6-1 UMFT12XEV Circuit Schematic .................................................................................................. 18

Figure 6-2 UMFT120DC Circuit Schematic .................................................................................................. 20

Figure 6-3 UMFT121DC Circuit Schematic .................................................................................................. 21

Figure 6-4 UMFT122DC Circuit Schematic .................................................................................................. 22

Figure 7-1 Plug in micro USB cable ............................................................................................................. 24

Figure 7-2 Connect TTL-232R-3V3 UART cable .......................................................................................... 24

Figure 7-3 Flash Magic configuration .......................................................................................................... 25

List of Tables

Table 2-1 Ordering information ...................................................................................................................... 1

Table 3-1 UMFT120DC J1 Pin Out Description ............................................................................................. 5

Table 3-2 UMFT121DC J1 Pin Out Description ............................................................................................. 6

Table 3-3 UMFT122DC J1 Pin Out Description ............................................................................................. 8

Table 4-1 Default setting of the jumpers ..................................................................................................... 10

Table 6-1 UMFT12XEV BOM list ................................................................................................................... 19

Table 6-2 UMFT120DC BOM list ................................................................................................................... 20

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

Table 6-3 UMFT121DC BOM list ................................................................................................................... 21

Table 6-4 UMFT122DC BOM list ................................................................................................................... 22

Table A-1 Abbreviations................................................................................................................................ 29

Table A-2 References .................................................................................................................................... 29

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

Appendix B – Abbreviations and References

Term

Description

CDC

Communications Device Class

DUT

Device Under Test

GPIO

General Purpose Input/Output

HID

Human Interface Device

ISP

In System Program

JTAG

Joint Test Action Group

LED

Light Emitting Diode

MCU

Micro Controller Unit

OS

Operating System

PCB

Printed Circuit Board

SPI

Serial Parallel Interface

SWD

Serial Wire Debug

UART

Universal Asynchronous Receiver/Transmitter

USB

Universal Serial Bus

VCP

Virtual COM Port

Table A-1 Abbreviations

Title

Description

FT_000646

FT120 IC data sheet

FT_000648

FT121 IC data sheet

FT_000647

FT122 IC data sheet

AN_209

PDIUSBD12 to FT120 Migration Guide

AN_225

FT12x firmware programming guide

TTL-232R-3V3

USB cable

USB to UART converter cable. Refer to

http://www.ftdichip.com/Products/Cables/USBTTLSerial.htm

Serial Loopback

test utility

http://www.madsencircuits.com/serial_loopback.html

Flash Magic

LPC microcontroller firmware programming tool. Refer to

http://www.flashmagictool.com

LPCXpresso

LPC microcontroller integrated development platform. Refer to

http://ics.nxp.com/lpcxpresso/ and http://lpcxpresso.code-red-

tech.com/LPCXpresso/

Table A-2 References

FT12 Series Evaluation Kit Datasheet

Version 1.0

Document Reference No.: FT_000728 Clearance No.: FTDI# 314

Appendix C - Revision History

Document Title: DS_UMFT12xA FT12 Series Evaluation Kit datasheet

Document Reference No.: FT_000728

Clearance No.: FTDI#314

Product Page: http://www.ftdichip.com/Products/Modules/DevelopmentModules.htm

Document Feedback: Send Feedback

Version 1.0 1.0 Created 03/09/2012

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

FTDI:

UMFT122DC UMFT12XEV UMFT120DC UMFT121DC