VVC1 VVC2 Voltage Controlled Crystal Oscillator Features * VCXO with a CMOS output * Small 5.0 X 7.0 X 1.9 mm package * Output frequencies to 66 MHz * 5.0 or 3.3 V operation * Low Jitter < 6 pS rms, fo>12MHz * Tri-State Output for test and board debug * 0/70 or -40/85 C operating temperature * Hermetically sealed ceramic SMD package * Lead free construction The VVC1 Voltage Controlled Crystal Oscillator * Product is compliant to RoHS directive and fully compatible with lead free assembly Applications * SONET/SDH/DWDM * Ethernet, Gigabit Ethernet ESD Diodes * xDSL/PCMCIA cards * Digital Video Vc fO Input Buffer Output Buffer / Tri-state * Broadband Access Description Vectron's VVC1/VVC2 Voltage Controlled Crystal Oscillator (VCXO) is a quartz stabilized square wave generator with a CMOS output and is tested at CMOS and TTL (5.0 volt operation) logic levels. The VVC1/VVC2 uses fundamental crystals resulting in low jitter performance and a monolithic IC which improves reliability and reduces cost. Vectron International 267 Lowell Road, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com VVC1, VVC2 Voltage Controlled Crystal Oscillator Performance Characteristics Table 1. Electrical Performance Parameter Frequency Supply Voltage 1 (+5.0 V 5%) (+3.3 V 5%) (+2.7 V + 5%)4 Supply Current (+5.0 V) (+2.7 or +3.3 V) Output Logic Levels Output Logic High2 Output Logic Low2 Transition Times Rise Time2 Fall Time2 Symmetry or Duty Cycle3 Operating temperature (ordering option) Total Pull Range (ordering option) Or Absolute Pull Range Test Conditions for APR (+5V option) Test Conditions for APR (+3.3V option) Gain Transfer Control Voltage Impedance Control Voltage Bandwidth (-3dB) Package Size Symbol fO VDD Min 1.544 4.750 3.135 2.7 Typical Maximum 65.536 5.250 3.465 2.835 55 40 5.0 3.3 2.7 IDD VOH VOL Units MHz V mA 0.9*VDD V V 0.1VDD tR tF SYM 45 VC VC 0.5 0.3 50 0/70 or -40/85 50, 100 or 150 5 5 55 ns ns % C ppm 4.5 3.0 V V ppm/V Kohm kHz mm 50, 80 or 100 Positive 90 BW 10 5.0 x 7.0 x 1.9 1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended. 2. Figure 1 defines these parameters. Figure 2 illustrates the equivalent five gate TTL load and operating conditions under which these parameters are tested and specified. 3. Symmetry is defined as (ON TIME/PERIOD with Vs= 1.4 V for TTL and Vs=2.5 V for CMOS, 5 volt operation, and Vs=1.65V for 3.3 Volt operation. 4. Only available as 50 ppm APR. tF tR IDD 650 80 % 6 Vs 20 % V DD + - .1F .01F 1 IC On Time VC + - 2 5 3 4 15pF 1.8k Period Figure 1. Output Waveform Vectron International 267 Lowell Rd, Hudson NH 03051 Figure 2. Typical Output Test Conditions (255C) Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com VVC1, VVC2 Voltage Controlled Crystal Oscillator Outline Diagram, Pad Layout and Pin Out Pin # Symbol Function 1 2 3 4 5 VC NC or Tri-state GND fO Tri-state or NC 6 VDD Control Voltage No Connect or Tri-state Ground Output Frequency Logic low disables output Logic high or no connection enables output waveform Supply Voltage Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com VVC1, VVC2 Voltage Controlled Crystal Oscillator Tape and Reel J F G C D B A L I E H K Table 2. Tape and Reel Dimensions (mm) Tape Dimensions Product A VVC1/2 16 B C D E 7.5 1.5 4 8 Reel Dimensions F G H 2 21 13 I J K L 60 2 17 180 # Per Reel 1000 Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional operation is not implied at these or any other conditions in excess of conditions represented in the operational sections of this data sheet. Exposure to absolute maximum ratings for extended periods may adversely affect device reliability. Table 3. Absolute Maximum Ratings Parameter Symbol Power Supply VDD Storage Temperature Tstorage Voltage Control Range VC Vectron International 267 Lowell Rd, Hudson NH 03051 Ratings 6 -55/125 Gnd to VDD Tel: 1-88-VECTRON-1 Unit Vdc C V e-mail: vectron@vectron.com VVC1, VVC2 Voltage Controlled Crystal Oscillator Reliability The VVC1/VVC2 is capable of meeting the following qualification tests. Table 4. Environnemental Compliance Parameter Mechanical Shock Mechanical Vibration Solderability Gross and Fine Leak Resistance to Solvents Moisture Sensitivity Level Conditions MIL-STD-883 Method 2002 MIL-STD-883 Method 2007 MIL-STD-883 Method 2003 MIL-STD-883 Method 1014 MIL-STD-883 Method 2016 1 Handling Precautions Although ESD protection circuitry has been designed into the the VVC1/VVC2, proper precautions should be taken when handling and mounting. VI employs a Human Body Model and a Charged-Device Model (CDM) for ESD susceptibility testing and design protection evaluation. ESD thresholds are dependent on the circuit parameters used to define the model. Although no industry wide standard has been adopted for the CDM, a standard HBM of resistance = 1.5kohms and capacitance = 100pF is widely used and therefore can be used for comparison purposes. Table 5. ESD Ratings Model Human Body Model Charged Device Model Minimum 1500 1000 Conditions MIL-STD-883 Method 3115 JESD 22-C101 Suggested IR profile Devices are built using lead free epoxy and can also be subjected to standard lead free IR reflow conditions. Table 6. Reflow Profile (IPC/JEDEC J-STD-020) Parameter Symbol PreHeat Time Ramp Up tS 60 sec Min, 200 sec Max R UP 3 C/sec Max tL 60 sec Min, 150 sec Max o Time Above 217 C Time To Peak Temperature Value o t AMB-P 480 sec Max tP 20 sec Min, 40 sec Max o Time At 260 C (max) Time At 240C (max) tp2 60 sec MAX Ramp Down R DN 6 C/sec Max Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 o e-mail: vectron@vectron.com VVC1, VVC2 Voltage Controlled Crystal Oscillator Table 7. Standard Frequencies (MHz) 1.544 2.048 4.096 8.192 10.000 12.000 12.288 12.352 13.000 14.318 15.440 16.000 16.384 18.432 19.440 20.000 20.480 24.576 24.704 27.000 30.000 32.000 32.768 34.368 35.328 38.880 40.000 40.960 44.736 51.840 52.000 62.208 65.536 Other frequencies may be available upon request. Standard frequencies are frequencies which the crystal has been designed and does not imply a stock position. Ordering Information Frequency ex.: 44M736 = 44.736MHz Product Family VV = VCXO Temperature Range, Stability (for TPR) B= 0/70C, 50 ppm D= -40/85C, 50 ppm E= 0/70C, 25 ppm F= -40/85C, 25 ppm Package 5x7x1.9 Tristate 1= Pin 5 2= Pin 2 Absolute Pull Range G= 50 ppm APR N= 80 ppm APR H= 100 ppm APR Power Supply, Linearity A= 5.0V, 20% Linearity B= 3.3V, 20% Linearity C= 5.0V, 10% Linearity D= 2.7V, 20% Linearity* F= 3.3V, 10% Linearity or Total Pull Range 1= 50 ppm 2= 100 ppm 3= 150 ppm NOTE: Not all combinations of options are available. Higher frequencies have less pull capability, especially at +3.3 volts supply, and higher pull can result in 20% linearity instead of 10%. Consult factory or your local sales representative with application requirements. * Only 50 ppm APR is available with this power supply For Additional Information, Please Contact: www.vectron.com USA: Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * Fax: 1-888-FAX-VECTRON EUROPE: Landstrasse, D-74924, Neckarbischofsheim, Germany * Tel: 49 (0) 7268 8010 * Fax: 49 (0) 7268 801281 ASIA: Vectron Asia Pacific Sales 1F~2F. No.8 Workshop No.308 Fenju Rd., WaiGaoQiao Free Trade Zone, Pudong New Area Shanghai, China 200131 *Tel: 8621 50480777 * Fax: 8621 50481881 Vectron International reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. VVC1 (October 2007) Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com